Makefile: Lower limit of --xram-size to protect ChaCha20 space

ChaCha20 uses 256 bytes starting from 0xbf00 for its calculations.
Make sure the linker checks that this space is not overwritten.

.github/workflows/build.yml

@@ -20,7 +20,11 @@ jobs:
           apt install make gcc sdcc xxd python-is-python3 libjson-c-dev zlib1g-dev -y
       - name: Run the host-side unit tests
         run: make -C test
-      - name: Check if machine.c can be compiled for all machines
+      - name: Check that every machine definition can be compiled
         run: make machine_check
-      - name: Make project
-        run: make MACHINE="KP_9000_6XHML_X2"
+      - name: Make project (4x2/RTL8372)
+        run: make CI=1 MACHINE="KP_9000_6XHML_X2"
+      - name: Make project (8x1/RTL8373)
+        run: make CI=1 MACHINE="KP_9000_9XHML_X_V3_1"
+      - name: Make project with the health instrumentation
+        run: make clean && make CI=1 MACHINE="KP_9000_6XHML_X2" HEALTH=1

CHANGELOG.md

@@ -14,6 +14,12 @@
 
 ## Fixed
 
+- Config
+  - A startup configuration line longer than the command buffer no longer stops the replay:
+    the offending line is skipped and the following lines are still applied.
+  - The web UI and the configuration upload now refuse a line the replay cannot take,
+    instead of writing it to flash.
+
 ## Breaking changes
 
 - Config

Dockerfile

@@ -8,6 +8,7 @@ RUN apt-get update && apt-get install -y \
     python3 \
     libjson-c-dev \
     git \
+    zlib1g-dev \
     && rm -rf /var/lib/apt/lists/*
 
 # git safe.directory for mounted repos (Makefile uses git describe)

Makefile

@@ -7,18 +7,32 @@ HTML_LOCATION = 262144
 ifeq ($(origin CC),default)
 CC = sdcc
 endif
-CC_FLAGS = -mmcs51 -I. -Ihttpd -Iuip
+CC_FLAGS = -mmcs51 -I. -Imachine -Ihttpd -Iuip
 ASM ?= sdas8051
 AFLAGS= -plosgff
 
 SUBDIRS := tools
 SUBDIRSCLEAN=$(addsuffix clean,$(SUBDIRS))
 
-ifeq ($(MACHINE),)
-	MACHINE:= $(shell grep "^\s*#define MACHINE_" machine.h | sed "s/^\s*#define MACHINE_//")
-else
+# $MACHINE selects machine/$(MACHINE).c as the board definition and is passed
+# on as -DMACHINE_$(MACHINE), which the rest of the firmware tests with
+# #if defined(MACHINE_...), and as -DMACHINE_NAME, which machine.h uses to
+# include machine/$(MACHINE).h. Both take the same value, so they cannot drift.
+ifneq ($(MACHINE),)
 	CC_FLAGS += -DMACHINE_$(MACHINE)
+	CC_FLAGS += -DMACHINE_NAME=$(MACHINE)
 endif
+# Health instrumentation and the "health" console command: HEALTH=1 gmake ...
+ifneq ($(HEALTH),)
+	CC_FLAGS += -DHEALTH
+endif
+
+ifeq ($(CI),1)
+	CC_FLAGS += --Werror
+endif
+
+# The board definition being built: one file per MACHINE_* symbol in machine.h.
+MACHINE_SRC = machine/$(MACHINE).c
 
 BUILDDIR = output/$(MACHINE)
 VERSION_HEADER := version.h
@@ -43,16 +57,31 @@ BUILD_DATE := $(shell date -u -d @$(SOURCE_DATE_EPOCH) +"%Y-%m-%d %H:%M:%S" 2>/d
 	|| date -u -r $(SOURCE_DATE_EPOCH) +"%Y-%m-%d %H:%M:%S")
 endif
 
-all: create_build_dir $(VERSION_HEADER) $(SUBDIRS) $(BUILDDIR)/rtlplayground-$(FILENAME_EXTENSION).bin
+# $(MACHINE_SRC) is listed here so an unknown $MACHINE fails before anything else
+# is built, including the tools/ subdirectory.
+all: create_build_dir $(VERSION_HEADER) $(MACHINE_SRC) $(SUBDIRS) $(BUILDDIR)/rtlplayground-$(FILENAME_EXTENSION).bin
 
 create_build_dir:
 	mkdir -p "$(BUILDDIR)"
 	mkdir -p "$(BUILDDIR)/uip"
 	mkdir -p "$(BUILDDIR)/httpd"
+	mkdir -p "$(BUILDDIR)/machine"
+	mkdir -p "$(BUILDDIR)/crypto"
 
-# Keep machine.c in first position to fail immediately on invalid $MACHINE value
+# Every machine is a pair machine/<MACHINE>.c + machine/<MACHINE>.h. Selecting
+# them by name means no #if/#elif chain, so an unknown or empty $MACHINE is
+# caught here instead of by a #error further down the build.
+$(MACHINE_SRC):
+	@echo "ERROR: MACHINE='$(MACHINE)' has no definition (expected $(MACHINE_SRC))." >&2
+	@echo "       Every machine is one file pair under machine/, named after the" >&2
+	@echo "       MACHINE_* symbol it defines; see machine/*.c for the full list." >&2
+	@echo "       Example: make MACHINE=KP_9000_6XHML_X2" >&2
+	@false
+
+# Keep the per-machine definition in first position to fail immediately on an
+# invalid $MACHINE value
 SRCS = \
-	machine.c \
+	$(MACHINE_SRC) \
 	machine_init.c \
 	cmd_editor.c \
 	cmd_parser.c \
@@ -61,8 +90,13 @@ SRCS = \
 	rtlplayground.c \
 	boot.c \
 	sfp.c \
+	dns.c \
+	dns_cli.c \
+	ntp.c \
+	ntp_cli.c \
 	syslog.c \
-	udp_apps.c
+	udp_apps.c \
+	crypto/chacha20.c
 
 # RTL837x
 SRCS += \
@@ -71,10 +105,15 @@ SRCS += \
 	rtl837x_igmp.c \
 	rtl837x_init.c \
 	rtl837x_leds.c \
+	rtl837x_leds_dump.c \
 	rtl837x_phy.c \
 	rtl837x_pins.c\
 	rtl837x_port.c \
-	rtl837x_stp.c
+	rtl837x_stp.c \
+	rtl837x_lldp.c \
+	rtl837x_storm.c \
+	rtl837x_lacp.c \
+	rtl837x_trap.c
 SRCS += \
 	httpd/httpd.c \
 	httpd/page_impl.c
@@ -104,11 +143,14 @@ html_min: $(HTML)
 html_data.c html_data.h &: $(HTML) | tools html_min
 	tools/output/fileadder -a $(HTML_LOCATION) -s $(IMAGESIZE) -b BANK1 -z -d $(HTML_MIN) -p html_data
 
-$(VERSION_HEADER):
+$(VERSION_HEADER): FORCE
 	@printf '%s\n' "#ifndef VERSION_H" "#define VERSION_H" \
 		"#define VERSION_SW \"$(VERSION_EXTENSION)\"" \
 		"#define BUILD_DATE \"$(BUILD_DATE)\"" \
-		"#endif" > $(VERSION_HEADER)
+		"#endif" > $(VERSION_HEADER).tmp
+	@cmp -s $(VERSION_HEADER).tmp $(VERSION_HEADER) \
+		&& rm -f $(VERSION_HEADER).tmp \
+		|| mv $(VERSION_HEADER).tmp $(VERSION_HEADER)
 
 httpd: html_data.h
 
@@ -126,15 +168,25 @@ distclean: $(SUBDIRSCLEAN)
 $(SUBDIRSCLEAN):
 	$(MAKE) -C $(@:clean=) clean
 
-$(BUILDDIR)/%.rel: %.c | create_build_dir html_data.h
+# Objects depend on the flags they were built with, through a stamp file that
+# is rewritten only when CC_FLAGS actually changes.
+CCFLAGS_STAMP := $(BUILDDIR)/.ccflags
+
+.PHONY: FORCE
+FORCE:
+
+$(CCFLAGS_STAMP): FORCE | create_build_dir
+	@echo '$(CC_FLAGS)' | cmp -s - $@ 2>/dev/null || echo '$(CC_FLAGS)' > $@
+
+$(BUILDDIR)/%.rel: %.c $(CCFLAGS_STAMP) | create_build_dir html_data.h
 	$(CC) -MMD $(CC_FLAGS) -o $@ -c $<
 
-$(BUILDDIR)/%.rel: %.asm | create_build_dir
+$(BUILDDIR)/%.rel: %.asm $(CCFLAGS_STAMP) | create_build_dir
 	${ASM} ${AFLAGS} -o $@ $<
 #	mv -f $(addprefix $(basename $^), .lst .rel .sym) .
 
-$(BUILDDIR)/rtlplayground.ihx: $(OBJS) $(BUILDDIR)/crtbank.rel $(BUILDDIR)/crc16.rel
-	$(CC) $(CC_FLAGS) -Wl-bHOME=0x00000 -Wl-bBANK1=0x14000 -Wl-bBANK2=0x24000 -Wl-bBANK3=0x34000 -Wl-r -o $@ $^
+$(BUILDDIR)/rtlplayground.ihx: $(OBJS) $(BUILDDIR)/crtbank.rel $(BUILDDIR)/crc16.rel $(BUILDDIR)/crypto/chacha_8051.rel
+	$(CC) $(CC_FLAGS) --xram-size 48896 -Wl-bHOME=0x00000 -Wl-bBANK1=0x14000 -Wl-bBANK2=0x24000 -Wl-bBANK3=0x34000 -Wl-r -o $@ $^
 
 $(BUILDDIR)/rtlplayground.img: $(BUILDDIR)/rtlplayground.ihx
 	objcopy --input-target=ihex -O binary $< $@
@@ -144,21 +196,28 @@ $(BUILDDIR)/rtlplayground-$(FILENAME_EXTENSION).bin: $(BUILDDIR)/rtlplayground.i
 	tools/output/imagebuilder -i $^ $@
 	tools/output/fileadder -a $(DEFAULT_CONFIG_LOCATION) -s $(IMAGESIZE) -d config.txt $@
 	tools/output/fileadder -a $(CONFIG_LOCATION) -s $(IMAGESIZE) -d config.txt $@
-	tools/output/fileadder -a $(HTML_LOCATION) -s $(IMAGESIZE) -z -d $(HTML_MIN) -p html_data -b BANK1 $@
+	tools/output/fileadder -a $(HTML_LOCATION) -s $(IMAGESIZE) -z -d $(HTML_MIN) -b BANK1 $@
 	tools/output/crc_calculator -u $@
 	ln -sf $(MACHINE)/rtlplayground-$(FILENAME_EXTENSION).bin output/rtlplayground.bin
 
-.PHONY: clean distclean all $(SUBDIRS) $(SUBDIRSCLEAN) $(VERSION_HEADER) create_build_dir
+.PHONY: clean distclean all $(SUBDIRS) $(SUBDIRSCLEAN) create_build_dir
+
+# Every machine/ definition is compiled, so a machine added to machine/ is
+# covered without registering it anywhere. The machine-specific defines are
+# filtered out of $(CC_FLAGS) and supplied per iteration instead, so this also
+# works as "make machine_check MACHINE=...".
+MACHINE_DEFS := $(sort $(patsubst machine/%.c,%,$(wildcard machine/*.c)))
+MACHINE_LESS_CC_FLAGS = $(filter-out -DMACHINE_%,$(CC_FLAGS))
 
 .PHONY:
 machine_check:
 	@mkdir -p $(BUILDDIR)/tmp
 	@set -eo pipefail; \
-	for MACHINE in `grep -E '^[[:space:]]*(//[[:space:]]*)?#define MACHINE_' machine.h | sed -E 's%^[[:space:]]*(//[[:space:]]*)?#define MACHINE_%%' | awk '{print $$1}' | sort -u`; \
+	for MACHINE in $(MACHINE_DEFS); \
 	do \
 	echo "Checking $${MACHINE}"; \
-	$(CC) $(CC_FLAGS) -DMACHINE_$${MACHINE} -MMD -o $(BUILDDIR)/tmp/machine_check -c machine.c; \
-	$(CC) $(CC_FLAGS) -DMACHINE_$${MACHINE} -MMD -o $(BUILDDIR)/tmp/machine_check -c machine_init.c; \
+	$(CC) $(MACHINE_LESS_CC_FLAGS) -DMACHINE_$${MACHINE} -DMACHINE_NAME=$${MACHINE} -MMD -o $(BUILDDIR)/tmp/machine_check -c machine/$${MACHINE}.c; \
+	$(CC) $(MACHINE_LESS_CC_FLAGS) -DMACHINE_$${MACHINE} -DMACHINE_NAME=$${MACHINE} -MMD -o $(BUILDDIR)/tmp/machine_check -c machine_init.c; \
 	done
 	@rm -rf $(BUILDDIR)/tmp
 

README.md

@@ -344,6 +344,7 @@ netmask zzz.zzz.zzz.zzz = Network mask of the switch
 port x name xxx         = Name xxx the port number x
 port z 1g               = Set 1g speed for port z
 igmp on/off             = Turn IGMP on or off
+session xxxx            = Web session timeout in seconds (default 200)
 ```
 [To be continue]
 
@@ -358,5 +359,7 @@ The following documents give further documentation on specific features of the R
 - [IGMP (IP-MC streaming)](doc/igmp.md)
 - [SFP+ ports](doc/sfp.md) 
 - [Trunking aka. port aggregation](doc/trunking.md)
+- [LACP (802.3ad link aggregation)](doc/lacp.md)
 - [VLAN](doc/vlan.md)
+- [Storm control](doc/storm_control.md)
 - [Modifications and Flash replacement](doc/mods.md)

boot.c

@@ -21,8 +21,9 @@ extern __code const struct machine machine;
 extern __xdata struct machine_runtime machine_detected;
 extern __xdata uint8_t sfr_data[4];
 extern volatile __xdata uint32_t ticks;
+__xdata uint32_t rtl8224_release_tick;
 extern __xdata uint8_t tx_seq;
-extern __code uint8_t * __code hex;
+extern __code const uint8_t * __code const hex;
 
 
 
@@ -240,10 +241,10 @@ void rtl8224_enable(void) __banked
 	reg_bit_clear(RTL837X_REG_GPIO_32_63_OUTPUT, 4);
 	// Configure Pin as output
 	reg_bit_set(RTL837X_REG_GPIO_32_63_DIRECTION, 4);
-	delay(100);
+	delay(4);
 	// Set pin 4 high
 	reg_bit_set(RTL837X_REG_GPIO_32_63_OUTPUT, 4);
-	delay(500);
+	rtl8224_release_tick = ticks;
 }
 
 
@@ -397,10 +398,12 @@ void setup_i2c(void) __banked
 	// HW Control register, enable I2C depending on PIN configuration
 	reg_read_m(RTL837X_PIN_MUX_1);
 	for (uint8_t sfp = 0; sfp < machine.n_sfp; sfp++) {
-		const uint8_t scl_bus = i2c_bus_from_scl_pin(machine.sfp_port[sfp].i2c.scl);
-		const uint8_t sda_bus = i2c_bus_from_sda_pin(machine.sfp_port[sfp].i2c.sda);
+		uint8_t i2c = machine.sfp_port[sfp].i2c;
+		uint8_t scl_bus = (i2c >> RTL837X_REG_I2C_SCL_SHIFT) & RTL837X_REG_I2C_SCL_MASK;
+		uint8_t sda_bus = (i2c >> RTL837X_REG_I2C_SDA_SHIFT) & RTL837X_REG_I2C_SDA_MASK;
 		print_string("Configuring I2C for SFP idx="); print_byte(sfp); print_string(" SCL="); print_byte(scl_bus); print_string(", SDA="); print_byte(sda_bus); write_char('\n');
-		switch (scl_bus) {
+		// `& RTL837X_REG_I2C_SCL_MASK` is needed to silens a compiler warning 110.
+		switch (scl_bus & RTL837X_REG_I2C_SCL_MASK) {
 			case 3:
 				// Bit 5-6 0b10 -> SCL (implies enabled SDA on bus 3)
 				sfr_mask_data(0, 0x60, 0x40);
@@ -419,8 +422,6 @@ void setup_i2c(void) __banked
 				sfr_mask_data(0, 0x80, 0x80);
 				sfr_mask_data(1, 0x01, 0x00);
 				break;
-			default:
-				print_string("Invalid SCL bus number: "); print_byte(scl_bus); write_char('\n');
 		}
 
 		switch (sda_bus) {
@@ -444,8 +445,6 @@ void setup_i2c(void) __banked
 				// Bit 9-10 0b01 -> SDA
 				sfr_mask_data(1, 0x06, 0x02);
 				break;
-			default:
-				print_string("Invalid SDA bus number: "); print_byte(sda_bus); write_char('\n');
 		}
 	}
 	reg_write_m(RTL837X_PIN_MUX_1);	

cmd_parser.c

@@ -5,6 +5,8 @@
 // #define DEBUG
 // #define REGDBG 1
 
+#include <8051.h>
+#include "cmd_parser.h"
 #include "rtl837x_common.h"
 #include "rtl837x_port.h"
 #include "rtl837x_flash.h"
@@ -12,35 +14,45 @@
 #include "rtl837x_regs.h"
 #include "rtl837x_sfr.h"
 #include "rtl837x_stp.h"
+#include "rtl837x_lacp.h"
 #include "rtl837x_igmp.h"
 #include "rtl837x_bandwidth.h"
+#include "rtl837x_lldp.h"
+#include "rtl837x_storm.h"
+#include "rtl837x_trap.h"
 #include "sfp.h"
 #include "dhcp.h"
 #include "syslog.h"
+#include "dns.h"
+#include "ntp.h"
 #include "uip/uip.h"
 #include "version.h"
 
 #include "machine.h"
+#include "rtl837x_leds.h"
 #include "phy.h"
 
 #pragma codeseg BANK2
 #pragma constseg BANK2
 
-extern __code struct machine machine;
+extern __code const struct machine machine;
 extern __xdata bool stp_enabled;
-extern __code uint8_t log_to_phys_port[9];
+extern __code const uint8_t log_to_phys_port[9];
+extern __xdata bool lldp_enabled;
 
 extern volatile __xdata uint32_t ticks;
 extern volatile __xdata uint8_t sfr_data[4];
 
-extern __code uint8_t * __code greeting;
-extern __code uint8_t * __code hex;
+extern __code const uint8_t * __code const greeting;
+extern __code const uint8_t * __code const hex;
 
 extern __xdata uint8_t flash_buf[FLASH_BUF_SIZE];
 extern __xdata struct flash_region_t flash_region;
 
 extern __xdata char passwd[21];
 
+extern __xdata uint16_t session_timeout;
+
 extern __xdata struct dhcp_state dhcp_state;
 
 __xdata uint8_t vlan_names[VLAN_NAMES_SIZE];
@@ -59,7 +71,6 @@ __xdata uint8_t hexvalue[4] = { 0 };
 
 // Buffer for writing to flash 0x1fd000, copy to 0x1fe000
 __xdata uint8_t cmd_buffer[CMD_BUF_SIZE];
-__xdata uint8_t cmd_available;
 
 __xdata	char save_cmd;
 
@@ -105,7 +116,7 @@ inline uint8_t isnumber(uint8_t l)
 	return (l <= ('9'-'0'));
 }
 
-uint8_t cmd_compare(uint8_t start, __code uint8_t * cmd)
+uint8_t cmd_compare(uint8_t start, __code const uint8_t * cmd)
 {
 	if (cmd_words_len == 0 || start > (cmd_words_len - 1)) {
 		return 0;
@@ -524,11 +535,21 @@ void parse_lag(void)
 		goto err;
 
 	if (cmd_compare(2, "d")) {
+		lacp_lag_set(group, 0);
 		port_lag_members_set(group, 0);
 		return;
 	}
 
 	uint8_t w = 2;
+	__xdata uint8_t lacp_mode = 0;
+	if (cmd_words_len > 2 && cmd_compare(2, "lacp")) {
+		lacp_mode = 1;
+		w = 3;
+		if (cmd_words_len > 3 && cmd_compare(3, "off")) {
+			lacp_lag_set(group, 0);
+			return;
+		}
+	}
 	while (w < cmd_words_len) {
 		// Parse port.
 		if (cmd_parse_port_separator(cmd_words_b[w++]) == 0)
@@ -536,10 +557,15 @@ void parse_lag(void)
 
 		members |= ((uint16_t)1) << atoi_results_u8;
 	}
-	port_lag_members_set(group, members);
+	if (lacp_mode) {
+		lacp_lag_set(group, members);
+	} else {
+		lacp_lag_set(group, 0);
+		port_lag_members_set(group, members);
+	}
 	return;
 err:
-	cmd_error("lag (show | <1-4> (d | <port>...))\n");
+	cmd_error("lag (show | <1-4> (d | [lacp] <port>...))\n");
 }
 
 
@@ -837,9 +863,14 @@ void parse_mirror(void)
 	if (cmd_words_len < 2)
 		goto err;
 
+	// The first argument is the mirroring (monitor) port
+	uint8_t ret = cmd_parse_port(cmd_words_b[1]);
+	if (ret == 0)
+		goto err;
+	mirroring_port = atoi_results_u8;
+
 	uint8_t w = 2;
 	uint8_t port;
-	uint8_t ret;
 	while (w < cmd_words_len) {
 		uint8_t idx = cmd_words_b[w++];
 		ret = cmd_parse_port(idx);
@@ -849,10 +880,6 @@ void parse_mirror(void)
 		idx += ret;
 		port = atoi_results_u8;
 
-		// Use the first port argument as mirroring_port
-		if (w == 2)
-			mirroring_port = port;
-
 		ret = cmd_buffer[idx];
 		uint16_t pmask = ((uint16_t)1) << port;
 		if (ret != 't')
@@ -875,6 +902,7 @@ void parse_port(void)
 		cmd_error("\nUsage:" \
 					 "\nport <port> [show|on|off]" \
 					 "\nport <port> [10m|100m|1g|2g5|duplex] [half|full]" \
+					 "\nport <port> lldp [block|permit]" \
 					 "\nport <port> name [custom port name]\n");
 		return;
 	}
@@ -893,10 +921,13 @@ void parse_port(void)
 		print_string_x(port_names[phy_settings.port]);
 		if (!machine.is_sfp[phy_settings.port]) {
 			phy_show(phy_settings.port);
+		} else {
+			write_char('\n');
 		}
+		port_media_show(phy_settings.port);
 	} else if (cmd_compare(2, "name")) {
 		uint8_t i = 0;
-		while ( (i < PORT_NAME_SIZE-1) && (cmd_buffer[cmd_words_b[3] + i] != NUL) ) {
+		while ( cmd_words_len > 3 && (i < PORT_NAME_SIZE-1) && (cmd_buffer[cmd_words_b[3] + i] != NUL) ) {
 			port_names[phy_settings.port][i] = name_char(cmd_buffer[cmd_words_b[3] + i]);
 			i++;
 		}
@@ -904,6 +935,14 @@ void parse_port(void)
 		print_string("\nName set to: \"");
 		print_string_x(port_names[phy_settings.port]);
 		print_string("\"\n");
+	} else if (cmd_compare(2, "lldp")) {
+		if (cmd_compare(3, "block")){
+			lldp_logical_port_status &= ~((uint16_t)1 << phy_settings.port);
+		} else if (cmd_compare(3, "permit")) {
+			lldp_logical_port_status |= (uint16_t)1 << phy_settings.port;
+		} else {
+			print_string ("Unknown port <port> lldp [block|permit] command\n");
+		}
 	} else if (machine.is_sfp[phy_settings.port]) {
 		print_string(" is SFP no PHY information available.\n");
 	} else if (cmd_compare(2, "10m")) {
@@ -1165,6 +1204,32 @@ err:
 }
 
 
+static void print_temperature(uint16_t reg)
+{
+	int16_t v;
+
+	reg_read(reg);
+	v = SFR_DATA_U16;
+	if (v < 0) {
+		write_char('-');
+		v = -v;
+	}
+	itoa(v >> 7);
+	write_char('.');
+	itoa(((v & 0x7f) * 10) >> 7);
+	print_string(" C\n");
+}
+
+
+void parse_temp(void)
+{
+	print_string("\nChip temperature: ");
+	print_temperature(RTL837X_TM_RESULT);
+	print_string("At power-on:      ");
+	print_temperature(RTL837X_TM_RESULT_POWERON);
+}
+
+
 void parse_sdsget(void)
 {
 	__xdata uint8_t sds_id, page, reg, hex_size;
@@ -1427,7 +1492,7 @@ void parse_eee(void)
 			speed_word = 2;
 		} else if (cmd_is_space_or_nul(idx)) {
 			// Word 2 is a port number
-			if (cmd_parse_port_separator(idx) == 0) {
+			if (cmd_parse_port_separator(cmd_words_b[2]) == 0) {
 				cmd_error("Speed word invalid, use: [100m|1g|2g5]\n");
 				return;
 			}
@@ -1541,6 +1606,57 @@ err:
 	cmd_error("bw [in|out|status] <port> [<hexvalue>|off|drop|fc]\n");
 }
 
+static __code const char * __code const storm_types[STORM_TYPES] = { "bcast", "mcast", "ucast", "umcast" };
+
+void parse_storm(void)
+{
+	uint8_t port, type, d;
+	__xdata uint32_t rate;
+	__xdata uint8_t *p;
+
+	if (cmd_words_len == 1)
+		return storm_show();
+	if (cmd_words_len < 4 || !cmd_parse_port_separator(cmd_words_b[1]))
+		goto err;
+	port = atoi_results_u8;
+
+	type = 0;
+	while (!cmd_compare(2, storm_types[type])) {
+		if (++type == STORM_TYPES)
+			goto err;
+	}
+
+	if (cmd_words_len == 4 && cmd_compare(3, "off"))
+		return storm_off(port, type);
+	if (cmd_words_len != 5)
+		goto err;
+
+	rate = 0;
+	p = &cmd_buffer[cmd_words_b[3]];
+	do {
+		d = *p++ - '0';
+		if (d > 9 || rate > 99999999)
+			goto err;
+		rate = (rate << 3) + (rate << 1) + d;
+	} while (*p != ' ' && *p != NUL);
+
+	if (cmd_compare(4, "pps")) {
+		if (!rate || rate > 0xfffff)
+			goto err;
+		storm_set(port, type, rate, 1);
+	} else if (cmd_compare(4, "kbps")) {
+		if (!rate || rate > 10000000)
+			goto err;
+		storm_set(port, type, rate, 0);
+	} else {
+		goto err;
+	}
+	return;
+
+err:
+	print_string("usage: storm [<port> bcast|mcast|ucast|umcast <rate> pps|kbps|off]\n");
+}
+
 void parse_syslog(void)
 {
 	if (cmd_words_len < 2) // no argument -> print status
@@ -1609,6 +1725,25 @@ void parse_syslog(void)
 	}
 }
 
+void parse_session(void)
+{
+	if (cmd_words_len >= 2) {
+		/* atoi_short() returns zero for no digits and for a value past
+		 * 65535; a zero-second timeout is not useful either, so both
+		 * tests are needed. */
+		if (!atoi_short(cmd_words_b[1]) || !atoi_results_short) {
+			print_string("Must be 1-65535 s\n");
+			return;
+		}
+		session_timeout = atoi_results_short;
+	}
+	/* Also the confirmation after setting: one message for both. */
+	print_string("Session timeout: ");
+	itoa_short(session_timeout);
+	print_string(" s\n");
+}
+
+
 // Parse command into words
 // cmd_words_len contains the number of words found.
 // cmd_words_b[] contains only start of a word offset.
@@ -1751,6 +1886,10 @@ void cmd_parser(void) __banked
 			parse_mtu();
 		} else if (cmd_compare(0, "syslog")) {
 			parse_syslog();
+		} else if (cmd_compare(0, "dns")) {
+			dns_parse();
+		} else if (cmd_compare(0, "ntp") || cmd_compare(0, "time")) {
+			ntp_parse();
 		} else if (cmd_compare(0, "ip")) {
 			if (cmd_compare(1, "dhcp")) {
 				dhcp_start();
@@ -1847,6 +1986,17 @@ void cmd_parser(void) __banked
 			}
 		} else if (cmd_compare(0, "stp")) {
 			stp_parse();
+#ifdef HEALTH
+		} else if (cmd_compare(0, "health")) {
+			health_show();
+#endif
+		} else if (cmd_compare(0, "lacp")) {
+			if (cmd_compare(1, "show"))
+				lacp_show();
+			else if (cmd_compare(1, "off"))
+				lacp_off();
+			else
+				cmd_error("lacp (show | off); a group starts LACP with: lag <1-4> lacp <port>...\n");
 		} else if (cmd_compare(0, "pvid")) {
 			if (cmd_words_len == 3 && cmd_parse_port_separator(cmd_words_b[1]) != 0
 			    && atoi_short(cmd_words_b[2]) && atoi_results_short && atoi_results_short <= 4094)
@@ -1869,6 +2019,8 @@ void cmd_parser(void) __banked
 			write_char('\n');
 		} else if (cmd_compare(0, "gpio")) {
 			print_gpio_status();
+		} else if (cmd_compare(0, "leds")) {
+			leds_dump();
 		} else if (cmd_compare(0, "regget")) {
 			parse_regget();
 		} else if (cmd_compare(0, "regset")) {
@@ -1889,13 +2041,12 @@ void cmd_parser(void) __banked
 			parse_eee();
 		} else if (cmd_compare(0, "bw")) {
 			parse_bw();
+		} else if (cmd_compare(0, "temp")) {
+			parse_temp();
+		} else if (cmd_compare(0, "storm")) {
+			parse_storm();
 		} else if (cmd_compare(0, "version")) {
 			print_sw_version();
-		} else if (cmd_compare(0, "time")) {
-			print_string("  Tick counter: "); print_long(ticks); print_string("   Sec Counter: ");
-			reg_read_m(RTL837X_REG_SEC_COUNTER);
-			print_sfr_data();
-			write_char('\n');
 		} else if (cmd_compare(0, "history")) {
 			__xdata uint16_t p = (cmd_history_ptr + 1) & CMD_HISTORY_MASK;
 			__xdata uint8_t found_begin = 0;
@@ -1911,6 +2062,18 @@ void cmd_parser(void) __banked
 			}
 		} else if (cmd_compare(0, "ingress")) {
 			parse_ingress();
+		} else if (cmd_compare(0, "session")) {
+			parse_session();
+		} else if (cmd_compare(0, "lldp")) {
+			if (cmd_compare(1, "on")) {
+				print_string("LLDP enabled\n");
+				lldp_enabled = 1;
+				trap_rma_set(RTL837X_RMA0E_CONF, RTL837X_RMA_ACT_TRAP);
+			} else {
+				print_string("LLDP disabled\n");
+				lldp_enabled = 0;
+				trap_rma_set(RTL837X_RMA0E_CONF, RTL837X_RMA_ACT_FORWARD);
+			}
 		}
 		else {
 			cmd_error("Unknown command\n");
@@ -1962,6 +2125,7 @@ void execute_config(void) __banked
 	save_cmd = 0;
 
 	uint8_t cmd_idx = 0;
+	uint8_t skipping = 0;
 	do {
 		flash_region.addr = pos;
 		flash_region.len = FLASH_READ_BURST_SIZE;
@@ -1972,20 +2136,23 @@ void execute_config(void) __banked
 		do {
 			if (cmd_idx >= (CMD_BUF_SIZE - 1)) {
 				cmd_buffer[cmd_idx] = NUL;
-				print_string("ERROR: Command too long: ");
+				print_string("ERROR: Command too long, skipped: ");
 				print_string_x(cmd_buffer);
 				write_char('\n');
-				err_status = ERR_CMD_TOO_LONG;
-				goto config_done;
+				cmd_idx = 0;
+				skipping = 1;
 			}
 			c = flash_buf[cfg_idx++];
 			if (c == 0 || c == '\n') {
-				cmd_buffer[cmd_idx] = NUL;
-				if (cmd_idx) {
-					cmd_tokenize();
-					if (err_status != ERR_OK)
-						goto config_done;
-					cmd_parser();
+				if (skipping) {
+					skipping = 0;
+				} else {
+					cmd_buffer[cmd_idx] = NUL;
+					if (cmd_idx) {
+						cmd_tokenize();
+						if (err_status == ERR_OK)
+							cmd_parser();
+					}
 				}
 				if (c == 0)
 					goto config_done;
@@ -1993,8 +2160,10 @@ void execute_config(void) __banked
 				continue;
 			}
 
-			cmd_buffer[cmd_idx] = c;
-			cmd_idx++;
+			if (!skipping) {
+				cmd_buffer[cmd_idx] = c;
+				cmd_idx++;
+			}
 		} while (cfg_idx);
 
 		pages_left--;
@@ -2045,3 +2214,161 @@ void execute_commands(__xdata uint8_t *p) __banked {
 		p++;
 	};
 }
+
+#ifdef HEALTH
+/*
+ * Health instrumentation. The counters live in xdata and are fed from the
+ * main loop through the banked entry points below; the "health" command
+ * prints everything in one go. All figures are raw hex, diffing two dumps
+ * gives the rates. Phase times are in system ticks (SYS_TICK_HZ = 200,
+ * 5 ms each); a phase counts as slow when it spans 2 or more ticks.
+ */
+extern __xdata uint16_t len_left;	/* httpd: bytes still to send of the current file */
+extern __xdata uint8_t entry;		/* httpd: index of the file being sent */
+
+static __xdata uint32_t health_loops;
+__xdata uint16_t health_rx_frames;
+
+static __xdata uint16_t ph_last_t;
+static __xdata uint8_t  ph_max[HEALTH_PHASES];
+static __xdata uint16_t ph_slow[HEALTH_PHASES];
+
+/* The ISR increments ticks between the two byte reads of a 16-bit load, so
+ * read until two loads agree. */
+static uint16_t ticks_lo(void)
+{
+	uint16_t a, b;
+	a = (uint16_t)ticks;
+	do {
+		b = a;
+		a = (uint16_t)ticks;
+	} while (a != b);
+	return a;
+}
+
+
+void health_loop_start(void) __banked
+{
+	health_loops++;
+	ph_last_t = ticks_lo();
+}
+
+
+void health_phase(uint8_t id) __banked
+{
+	__xdata uint16_t now = ticks_lo();
+	__xdata uint16_t d = now - ph_last_t;
+	ph_last_t = now;
+	if (d > 0xff)
+		d = 0xff;
+	if ((uint8_t)d > ph_max[id])
+		ph_max[id] = d;
+	if (d >= 2)
+		ph_slow[id]++;
+}
+
+
+/* Fill the stack area above the current frame with a pattern; the dump scans
+ * for how much of it survived. The 8051 stack grows upward, so everything
+ * above SP is free at this point. Interrupts are held off so an ISR does not
+ * push into the area mid-paint. */
+void health_stack_paint(void) __banked
+{
+	__xdata uint8_t from = SP + 4;
+	__xdata uint8_t ea = EA;
+	EA = 0;
+	for (uint8_t i = 0xff; i >= from; i--)
+		*(__idata uint8_t *)i = 0xa5;
+	EA = ea;
+}
+
+
+static void ph_line(__code const char *name, uint8_t id)
+{
+	print_string(name);
+	print_string(" max ");
+	print_byte(ph_max[id]);
+	print_string(" slow ");
+	print_short(ph_slow[id]);
+	write_char('\n');
+}
+
+
+void health_show(void) __banked
+{
+	__xdata uint8_t i;
+
+	print_string("up ");
+	reg_read_m(RTL837X_REG_SEC_COUNTER);
+	print_byte(sfr_data[0]); print_byte(sfr_data[1]);
+	print_byte(sfr_data[2]); print_byte(sfr_data[3]);
+	print_string(" ticks ");
+	print_long(ticks);
+	print_string(" loops ");
+	print_long(health_loops);
+	print_string(" rx ");
+	print_short(health_rx_frames);
+	write_char('\n');
+
+	/* Phase timing: max duration seen (ticks of 5 ms) and slow-pass count */
+	ph_line("link", HEALTH_PH_LINK);
+	ph_line("sfp ", HEALTH_PH_SFP);
+	ph_line("rx  ", HEALTH_PH_RX);
+	ph_line("tx  ", HEALTH_PH_TX);
+	ph_line("stp ", HEALTH_PH_STP);
+	ph_line("cmd ", HEALTH_PH_CMD);
+
+	/* Stack: current depth plus how much of the painted area is untouched */
+	print_string("sp ");
+	print_byte(SP);
+	print_string(" untouched ");
+	i = 0;
+	while (*(__idata uint8_t *)(0xff - i) == 0xa5 && i < 0x86)
+		i++;
+	print_byte(i);
+	write_char('\n');
+
+	/* The TCP connection slot. One on this configuration; a build with more
+	 * has to say which slot each line is, so make that a visible decision. */
+#if UIP_CONNS != 1
+#error "health: the tcp dump prints a single slot, extend it for UIP_CONNS > 1"
+#endif
+	i = 0;
+	{
+		print_string("tcp ");
+		print_string("st ");
+		print_byte(uip_conns[i].tcpstateflags);
+		print_string(" tmr ");
+		print_byte(uip_conns[i].timer);
+		print_string(" rtx ");
+		print_byte(uip_conns[i].nrtx);
+		print_string(" rto ");
+		print_byte(uip_conns[i].rto);
+		print_string(" len ");
+		print_short(uip_conns[i].len);
+		print_string(" mss ");
+		print_short(uip_conns[i].mss);
+		write_char('\n');
+		print_string("  lport ");
+		print_short(HTONS(uip_conns[i].lport));
+		print_string(" rport ");
+		print_short(HTONS(uip_conns[i].rport));
+		print_string(" rip ");
+		print_short(HTONS(uip_conns[i].ripaddr[0]));
+		write_char(' ');
+		print_short(HTONS(uip_conns[i].ripaddr[1]));
+		write_char('\n');
+	}
+
+	/* httpd transfer state and the protocol flags */
+	print_string("httpd left ");
+	print_short(len_left);
+	print_string(" entry ");
+	print_byte(entry);
+	print_string(" stp ");
+	print_byte(stp_enabled);
+	print_string(" mvlan ");
+	print_short(management_vlan);
+	write_char('\n');
+}
+#endif

cmd_parser.h

@@ -6,9 +6,36 @@
 #include "rtl837x_common.h"
 
 extern __xdata uint8_t cmd_buffer[CMD_BUF_SIZE];
-extern __xdata uint8_t cmd_available;
+extern __bit __at(0x03) cmd_available;
 extern __xdata uint8_t err_status;
 
+/* Health instrumentation, built with HEALTH=1. Without it the hooks below
+ * compile to nothing and the "health" command does not exist. */
+#ifdef HEALTH
+/* Phase ids, in main-loop order */
+#define HEALTH_PH_LINK	0
+#define HEALTH_PH_SFP	1
+#define HEALTH_PH_RX	2
+#define HEALTH_PH_TX	3
+#define HEALTH_PH_STP	4
+#define HEALTH_PH_CMD	5
+#define HEALTH_PHASES	6
+#define HEALTH_LLDP     7
+
+extern __xdata uint16_t health_rx_frames;
+#define health_rx_frame()	health_rx_frames++
+
+void health_loop_start(void) __banked;	/* once per idle() pass, resets the phase baseline */
+void health_phase(uint8_t id) __banked;	/* after each phase; accounts ticks since last checkpoint */
+void health_stack_paint(void) __banked;	/* paint the unused stack area once at boot */
+void health_show(void) __banked;	/* "health" CLI dump */
+#else
+#define health_rx_frame()
+#define health_loop_start()
+#define health_phase(id)
+#define health_stack_paint()
+#endif
+
 void cmd_tokenize(void) __banked;
 void cmd_parser(void) __banked;
 void execute_config(void) __banked;

crypto/chacha.h

@@ -0,0 +1,23 @@
+#ifndef _CHACHA_H_
+#define _CHACHA_H_
+
+#include <stdint.h>
+
+struct chacha20_t {
+	uint8_t wstate[64];		// 64 bytes written here
+	uint8_t constant[16];		// 128 bit constant
+        uint8_t key[32];		// 256-bit secret key
+        uint32_t cnt;			// 32-bit block counter 1, 2.. Big Endian!
+        uint8_t nonce[12];		// 96-bit nonce
+        __xdata uint8_t *plaintext;
+        uint16_t length;
+        __xdata uint8_t *cyphertext;
+};
+
+// Encrypt a plaintext with ChaCha20 as per RFC7539
+void chacha20_encrypt(void);
+
+// Test ChaCha20 using the example from RFC7539
+void chacha20_test(void);
+
+#endif

crypto/chacha20.c

@@ -0,0 +1,103 @@
+#include "rtl837x_common.h"
+#include "chacha.h"
+
+void chacha_20(void);
+void chacha_update(void);
+void chacha_count(void);
+
+// generate a block of ChaCha20 keystream as per RFC7539
+
+
+__xdata struct chacha20_t __at(0xbf00) chacha20;
+
+#ifdef CHACHA20_TEST
+__xdata uint8_t plaintext[256];
+__xdata uint8_t cyphertext[256];
+#endif
+
+#ifdef DEBUG
+void chacha20_print_block(void)
+{
+        for (uint8_t i=0; i < 64; i++) {
+            print_byte(*(uint8_t * __xdata)(chacha20.wstate + i));
+	    if (i%4 == 3)
+		    write_char(' ');
+        }
+}
+#endif
+
+void chacha20_encrypt(void)
+{
+	__xdata uint8_t *p = chacha20.plaintext;
+
+	while (chacha20.length) {
+		register uint8_t i;
+		chacha_count();
+		memcpy(chacha20.wstate, chacha20.wstate + 64, 64);
+#ifdef DEBUG
+		chacha20_print_block(); write_char('\n');
+#endif
+		chacha_20();
+		chacha_update();
+#ifdef DEBUG
+		chacha20_print_block(); write_char('\n');
+#endif
+		for (i = 0; i < ((chacha20.length > 64) ? 64 : chacha20.length); i++)
+			*chacha20.cyphertext++ = *p++ ^ chacha20.wstate[i];
+		chacha20.length -= chacha20.length > 64 ? 64 : chacha20.length;
+#ifdef DEBUG
+		print_string("\n  round done\n");
+#endif
+	};
+}
+
+#ifdef CHACHA20_TEST
+// Test the example of RFC 7539 Section 2.4.2
+void chacha20_test(void)
+{
+	__code uint8_t chacha_c[16] =
+		{ 0x61, 0x70, 0x78, 0x65,  0x33, 0x20, 0x64, 0x6e,
+		  0x79, 0x62, 0x2d, 0x32,  0x6b, 0x20, 0x65, 0x74 };
+
+	__code uint8_t key[32] =
+		{ 0x03, 0x02, 0x01, 0x00,  0x07, 0x06, 0x05, 0x04,
+		  0x0b, 0x0a, 0x09, 0x08,  0x0f, 0x0e, 0x0d, 0x0c,
+		  0x13, 0x12, 0x11, 0x10,  0x17, 0x16, 0x15, 0x14,
+		  0x1b, 0x1a, 0x19, 0x18,  0x1f, 0x1e, 0x1d, 0x1c };
+	
+	__code uint8_t nonce[12] = {
+		  0x00, 0x00, 0x00, 0x00,  0x4a, 0x00, 0x00, 0x00,
+		  0x00, 0x00, 0x00, 0x00 };
+
+	__code uint8_t sunscreen[] = "Ladies and Gentlemen of the class of '99: If I could offer you only one tip for " \
+				     "the future, sunscreen would be it.";
+
+/*
+	Ciphertext Sunscreen (from RFC 7539 Section 2.4.2):
+	000  6e 2e 35 9a 25 68 f9 80 41 ba 07 28 dd 0d 69 81  n.5.%h..A..(..i.
+	016  e9 7e 7a ec 1d 43 60 c2 0a 27 af cc fd 9f ae 0b  .~z..C`..'......
+	032  f9 1b 65 c5 52 47 33 ab 8f 59 3d ab cd 62 b3 57  ..e.RG3..Y=..b.W
+	048  16 39 d6 24 e6 51 52 ab 8f 53 0c 35 9f 08 61 d8  .9.$.QR..S.5..a.
+	064  07 ca 0d bf 50 0d 6a 61 56 a3 8e 08 8a 22 b6 5e  ....P.jaV....".^
+	080  52 bc 51 4d 16 cc f8 06 81 8c e9 1a b7 79 37 36  R.QM.........y76
+	096  5a f9 0b bf 74 a3 5b e6 b4 0b 8e ed f2 78 5e 42  Z...t.[......x^B
+	112  87 4d 
+*/
+	strcpy(plaintext, sunscreen);
+	memcpyc(chacha20.constant, chacha_c, 16);
+	memcpyc(chacha20.key, key, 32);
+	chacha20.cnt = 0;
+	memcpyc(chacha20.nonce, nonce, 12);
+	chacha20.plaintext = plaintext;
+	chacha20.length = strlen_x(plaintext);
+	chacha20.cyphertext = cyphertext;
+
+	print_string("Encrypting...\n");
+	chacha20_encrypt();
+	print_string("Cypertext:\n");
+	uint16_t len = strlen_x(plaintext);
+	for (uint8_t i = 0; i < len; i++) {
+		print_byte(cyphertext[i]); write_char(' ');
+	}
+}
+#endif

crypto/chacha_8051.asm

@@ -0,0 +1,455 @@
+; ChaCha Quater-Round implementation in Assembler
+	.module chacha_8051
+; Global variables:
+	.globl _chacha_20
+	.globl _chacha_update
+	.globl _chacha_count
+
+;#define CHACHA_QR(A, B, C, D) { \
+;    A += B; D ^= A; D = ROTL32(D, 16);  \
+;    C += D; B ^= C; B = ROTL32(B, 12);  \
+;    A += B; D ^= A; D = ROTL32(D, 8);   \
+;    C += D; B ^= C; B = ROTL32(B, 7);   \
+;}
+
+; 		r0      r1    r2   r3
+; CHACHA_QR( v[ 0], v[ 4], v[ 8], v[12] );
+
+	.area HOME    (CODE)
+
+store_32:
+	ar7 = 0x07
+	ar6 = 0x06
+	ar5 = 0x05
+	ar4 = 0x04
+	ar3 = 0x03
+	ar2 = 0x02
+	ar1 = 0x01
+	ar0 = 0x00
+
+	mov	a, r7
+	movx	@dptr, a
+	dec	dpl
+	mov	a, r6
+	movx	@dptr, a
+	dec	dpl
+	mov	a, r5
+	movx	@dptr, a
+	dec	dpl
+	mov	a, r4
+	movx	@dptr, a
+	ret
+
+rol_b:
+	clr	c
+	mov	a, r7
+	rlc	a
+	mov	r7, a
+	mov	a, r6
+	rlc	a
+	mov	r6, a
+	mov	a, r5
+	rlc	a
+	mov	r5, a
+	mov	a, r4
+	rlc	a
+	mov	r4, a
+	clr	a
+	addc	a, r7
+	mov	r7, a
+	djnz	dpl, rol_b
+	ret
+
+
+chacha_plus_xor:
+; Load A into registers r4-r7, A pointed to by r0
+	mov	dptr, #_chacha20
+	mov	dpl, r0
+	movx	a, @dptr
+	mov	r7, a
+	dec	dpl
+	movx	a, @dptr
+	mov	r6, a
+	dec	dpl
+	movx	a, @dptr
+	mov	r5, a
+	dec	dpl
+	movx	a, @dptr
+	mov	r4, a
+
+; A += B, B pointed to by r1
+	mov	dpl, r1
+	movx	a, @dptr
+	add	a, r7
+	mov	r7, a
+
+	dec	dpl
+	movx	a, @dptr
+	addc	a, r6
+	mov	r6, a
+
+	dec	dpl
+	movx	a, @dptr
+	addc	a, r5
+	mov	r5, a
+
+	dec	dpl
+	movx	a, @dptr
+	addc	a, r4
+	mov	r4, a
+
+	mov	dpl, r0		; Store A back
+	mov	a, r7
+	movx	@dptr, a
+	dec	dpl
+	mov	a, r6
+	movx	@dptr, a
+	dec	dpl
+	mov	a, r5
+	movx	@dptr, a
+	dec	dpl
+	mov	a, r4
+	movx	@dptr, a
+
+; D ^= A
+	mov	dpl, r3
+	movx	a, @dptr
+	xrl	a, r7
+	mov	r7, a
+	dec	dpl
+
+	movx	a, @dptr
+	xrl	a, r6
+	mov	r6, a
+	dec	dpl
+
+	movx	a, @dptr
+	xrl	a, r5
+	mov	r5, a
+	dec	dpl
+
+	movx	a, @dptr
+	xrl	a, r4
+	mov	r4, a
+	dec	dpl
+	ret
+
+chacha_qr:
+; QR Part: A += B; D ^= A; D = ROTL32(D, 16);
+	acall	chacha_plus_xor
+
+; rotate left 16. D is r4, r5, r6, r7 -> r6, r7, r4, r5
+	mov	a, r6
+	xch	a, r4
+	mov	r6, a
+	mov	a, r7
+	xch	a, r5
+	mov	r7, a
+	mov     dpl, r3 ; Store D
+	acall   store_32
+
+;QR Part: C += D; B ^= C; B = ROTL32(B, 12);
+; Swap A <-> C and D <-> B
+	mov	a, r0
+	xch	a, r2
+	mov	r0, a
+	mov	a, r1
+	xch	a, r3
+	mov	r1, a
+	acall	chacha_plus_xor
+
+; rotate left 12. D is r4, r5, r6, r7 -> r5, r6, r7, r4
+	mov	a, r4
+	xch	a, r7
+	xch	a, r6
+	xch	a, r5
+	mov	r4, a
+
+	mov	dpl, #4
+	acall	rol_b
+	mov	dpl, r3	; Store D (being B)
+	acall	store_32
+
+; Swap A <-> C and D <-> B
+	mov	a, r0
+	xch	a, r2
+	mov	r0, a
+	mov	a, r1
+	xch	a, r3
+	mov	r1, a
+
+; QR Part A += B; D ^= A; D = ROTL32(D, 8);
+	acall	chacha_plus_xor
+	mov	a, r4
+	xch	a, r7
+	xch	a, r6
+	xch	a, r5
+	mov	r4, a
+	mov	dpl, r3	; Store D
+	acall	store_32
+
+; QR Part
+;    C += D; B ^= C; B = ROTL32(B, 7);
+line4:
+; Swap A <-> C and D <-> B
+	mov	a, r0
+	xch	a, r2
+	mov	r0, a
+	mov	a, r1
+	xch	a, r3
+	mov	r1, a
+	acall	chacha_plus_xor
+
+; Roll left 7 bits, start by rolling 8 bits left, then roll 1 to the right
+	mov	a, r4
+	xch	a, r7
+	xch	a, r6
+	xch	a, r5
+	mov	r4, a
+
+	clr	c
+	mov	a, r4
+	rrc	a
+	mov	r4, a
+	mov	a, r5
+	rrc	a
+	mov	r5, a
+	mov	a, r6
+	rrc	a
+	mov	r6, a
+	mov	a, r7
+	rrc	a
+	mov	r7, a
+	clr	a
+	rrc	a
+	add	a, r4
+	mov	r4, a
+
+; Swap A <-> C and D <-> B
+	mov	a, r0
+	xch	a, r2
+	mov	r0, a
+	mov	a, r1
+	xch	a, r3
+	mov	r1, a
+	mov	dpl, r1	; Store B
+	acall	store_32
+	ret
+
+
+;
+; Implementation of 20 ChaCha Rounds (10 Double Rounds)
+;
+_chacha_20:
+	push    acc
+	push    b
+	push    dpl
+	push    dph
+	push    ar7
+	push    ar6
+	push    ar5
+	push    ar4
+	push    ar3
+	push    ar2
+	push    ar1
+	push    ar0
+	push    psw
+
+	mov	b, #10 ; 10 Double rounds
+chacha_20_loop:
+;	CHACHA_QR( v[ 0], v[ 4], v[ 8], v[12] );
+	mov r0, #3
+	mov r1, #19
+	mov r2, #35
+	mov r3, #51
+	acall	chacha_qr
+	
+;        CHACHA_QR( v[ 1], v[ 5], v[ 9], v[13] ); 7  23  39  55
+	mov r0, #7
+	mov r1, #23
+	mov r2, #39
+	mov r3, #55
+	acall	chacha_qr
+
+; 	CHACHA_QR( v[ 2], v[ 6], v[10], v[14] ); 11 27  43  59
+	mov r0, #11
+	mov r1, #27
+	mov r2, #43
+	mov r3, #59
+	acall	chacha_qr
+
+;	CHACHA_QR( v[ 3], v[ 7], v[11], v[15] ); 15 31  47  63
+        mov r0, #15
+        mov r1, #31
+        mov r2, #47
+        mov r3, #63
+	acall	chacha_qr
+
+;	CHACHA_QR( v[ 0], v[ 5], v[10], v[15] ); 3  23  43  63
+	mov r0, #3
+	mov r1, #23
+	mov r2, #43
+	mov r3, #63
+	acall	chacha_qr
+
+;	CHACHA_QR( v[ 1], v[ 6], v[11], v[12] ); 7  27  47  51
+	mov r0, #7
+	mov r1, #27
+	mov r2, #47
+	mov r3, #51
+	acall	chacha_qr
+
+;	CHACHA_QR( v[ 2], v[ 7], v[ 8], v[13] ); 11 31  35  55
+	mov r0, #11
+	mov r1, #31
+	mov r2, #35
+	mov r3, #55
+	acall	chacha_qr
+
+;	CHACHA_QR( v[ 3], v[ 4], v[ 9], v[14] ); 15 19  39  59
+	mov r0, #15
+	mov r1, #19
+	mov r2, #39
+	mov r3, #59
+	acall	chacha_qr
+	djnz	b, chacha_20_loop
+
+	pop     psw
+	pop     ar0
+	pop     ar1
+	pop     ar2
+	pop     ar3
+	pop     ar4
+	pop     ar5
+	pop     ar6
+	pop     ar7
+	pop     dph
+	pop     dpl
+	pop     b
+	pop     acc
+	ret
+
+;
+; Update ChaCHa state
+;
+_chacha_update:
+	push    acc
+	push    b
+	push    dpl
+	push    dph
+	push    ar4
+	push    ar3
+	push    ar2
+	push    ar1
+	push    ar0
+	push    psw
+
+	mov	dptr, #_chacha20
+	mov	b, #16 ; 16 uint32
+update_loop:
+	mov	a, b ; multiply by 4 and subtract 1
+	rl	a
+	rl	a
+	dec	a
+; Load Working State variable into registers r0-r3
+	mov	dpl, a
+
+	orl	a, #64	; Save pointer to state
+	mov	r4, a
+
+	movx	a, @dptr
+	mov	r3, a
+	dec	dpl
+	movx	a, @dptr
+	mov	r2, a
+	dec	dpl
+	movx	a, @dptr
+	mov	r1, a
+	dec	dpl
+	movx	a, @dptr
+	mov	r0, a
+
+; Add to State variable
+	mov	a, r4
+	mov	dpl, a
+	movx	a, @dptr
+	add	a, r3
+	mov	r3, a
+
+	dec	dpl
+	movx	a, @dptr
+	addc	a, r2
+	mov	r2, a
+
+	dec	dpl
+	movx	a, @dptr
+	addc	a, r1
+	mov	r1, a
+
+	dec	dpl
+	movx	a, @dptr
+	addc	a, r0
+	mov	r0, a
+
+; Store back state variable in LSB, first sequence (serialized)
+	mov	a, r4
+	xrl	a, #64	; Save pointer to working state
+	mov	dpl, a
+	mov	a, r0
+	movx	@dptr, a
+	dec	dpl
+	mov	a, r1
+	movx	@dptr, a
+	dec	dpl
+	mov	a, r2
+	movx	@dptr, a
+	dec	dpl
+	mov	a, r3
+	movx	@dptr, a
+
+	djnz	b, update_loop
+
+	pop     psw
+	pop     ar0
+	pop     ar1
+	pop     ar2
+	pop     ar3
+	pop     ar4
+	pop     dph
+	pop     dpl
+	pop     b
+	pop     acc
+	ret
+
+;
+; Increase counter in state
+;
+_chacha_count:
+	push    acc
+	push    dpl
+	push    dph
+	mov	dptr, #_chacha20
+	mov	dpl, #112 + 3
+	movx	a, @dptr
+	inc	a
+	movx	@dptr, a	
+	jnz	chacha_count_done
+	dec	dpl
+	movx	a, @dptr
+	inc	a
+	movx	@dptr, a
+	jnz	chacha_count_done
+	dec	dpl
+	movx	a, @dptr
+	inc	a
+	movx	@dptr, a
+	jnz	chacha_count_done
+	dec	dpl
+	movx	a, @dptr
+	inc	a
+	movx	@dptr, a
+chacha_count_done:
+	pop     dph
+	pop     dpl
+	pop     acc
+	ret

dhcp.c

@@ -139,7 +139,6 @@ void dhcp_addopt_request_ip(void)
 	DHCP_OPT[dhcp_state.opt_ptr++] = dhcp_state.current_ip[1];
 	DHCP_OPT[dhcp_state.opt_ptr++] = dhcp_state.current_ip[2];
 	DHCP_OPT[dhcp_state.opt_ptr++] = dhcp_state.current_ip[3];
-	memcpy(&DHCP_OPT[dhcp_state.opt_ptr], uip_ethaddr.addr, 4);
 }
 
 
@@ -151,13 +150,11 @@ void dhcp_addopt_server_id(void)
 	DHCP_OPT[dhcp_state.opt_ptr++] = dhcp_state.server[1];
 	DHCP_OPT[dhcp_state.opt_ptr++] = dhcp_state.server[2];
 	DHCP_OPT[dhcp_state.opt_ptr++] = dhcp_state.server[3];
-	memcpy(&DHCP_OPT[dhcp_state.opt_ptr], uip_ethaddr.addr, 4);
 }
 
 
 void dhcp_send_discover(void)
 {
-	print_string("dhcp_send_discover called\n");
 	dhcp_prepare_request();
 
 	dhcp_state.opt_ptr = 0;
@@ -193,7 +190,6 @@ void dhcp_send_discover(void)
 
 void dhcp_send_request(void)
 {
-	print_string("dhcp_send_request called\n");
 	dhcp_prepare_request();
 
 	dhcp_state.opt_ptr = 0;
@@ -232,19 +228,21 @@ void ip_opt(__xdata uint8_t * ip)
 {
 	dhcp_state.opt_ptr++;
 	uint8_t len = DHCP_OPT[dhcp_state.opt_ptr++];
-	*ip++ = DHCP_OPT[dhcp_state.opt_ptr++];
-	*ip++ = DHCP_OPT[dhcp_state.opt_ptr++];
-	*ip++ = DHCP_OPT[dhcp_state.opt_ptr++];
-	*ip++ = DHCP_OPT[dhcp_state.opt_ptr++];
+	if (len >= 4)
+		memcpy(ip, &DHCP_OPT[dhcp_state.opt_ptr], 4);
 	 // There may be more than one IP option, such as 2 DNS servers advertised
-	dhcp_state.opt_ptr += len - 4;
+	dhcp_state.opt_ptr += len;
 }
 
 
-void long_opt(void)
+uint8_t long_opt(void)
 {
 	dhcp_state.opt_ptr++;
-	dhcp_state.opt_ptr++;
+	uint8_t len = DHCP_OPT[dhcp_state.opt_ptr++];
+	if (len < 4) {
+		dhcp_state.opt_ptr += len;
+		return 0;
+	}
 	long_value =  DHCP_OPT[dhcp_state.opt_ptr++];
 	long_value <<= 8;
 	long_value |= DHCP_OPT[dhcp_state.opt_ptr++];
@@ -252,6 +250,8 @@ void long_opt(void)
 	long_value |= DHCP_OPT[dhcp_state.opt_ptr++];
 	long_value <<= 8;
 	long_value |= DHCP_OPT[dhcp_state.opt_ptr++];
+	dhcp_state.opt_ptr += len - 4;
+	return 1;
 }
 
 
@@ -275,16 +275,16 @@ void parse_opts(void)
 			ip_opt(&dhcp_state.broadcast[0]);
 			break;
 		case DHCP_LEASE:
-			long_opt();
-			dhcp_state.lease = long_value;
+			if (long_opt())
+				dhcp_state.lease = long_value;
 			break;
 		case DHCP_REBIND:
-			long_opt();
-			dhcp_state.rebind = long_value;
+			if (long_opt())
+				dhcp_state.rebind = long_value;
 			break;
 		case DHCP_RENEWAL:
-			long_opt();
-			dhcp_state.renewal = long_value;
+			if (long_opt())
+				dhcp_state.renewal = long_value;
 			break;
 		case DHCP_END:
 			break;
@@ -376,13 +376,11 @@ void dhcp_start(void) __banked
 	*tid++ = SFR_DATA_8;
 	*tid = SFR_DATA_0;
 	dhcp_state.state = DHCP_START;
-	print_string("dhcp_start done\n");
 }
 
 
 void dhcp_stop(void) __banked
 {
-	print_string("dhcp_stop called\n");
 	uip_udp_remove(dhcp_state.conn);
 	dhcp_state.state = DHCP_OFF;
 }

dns.c

@@ -0,0 +1,238 @@
+/*
+ * DNS resolver for the RTL837x platform
+ * This code is in the Public Domain
+ */
+
+#include <stdint.h>
+#include "rtl837x_common.h"
+#include "cmd_parser.h"
+#include "uip/uip.h"
+#include "dhcp.h"
+#include "dns.h"
+
+#pragma codeseg BANK3
+#pragma constseg BANK3
+
+#define DNS_PORT	53
+#define DNS_TRIES	6
+#define DNS_TIMEOUT	(2 * SYS_TICK_HZ)
+
+extern __xdata struct dhcp_state dhcp_state;
+extern volatile __xdata uint32_t ticks;
+
+__xdata struct dns_state dns_state;
+__xdata uip_ipaddr_t dns_ip;
+uint8_t * __xdata dns_cand[3];
+
+
+static uint8_t dns_used(__xdata uint8_t *a) __reentrant
+{
+	return a[0] | a[1] | a[2] | a[3];
+}
+
+
+static uint8_t dns_name_is_ip(void) __reentrant
+{
+	__xdata char *s = dns_state.name;
+	uint8_t i, n;
+	uint16_t v;
+
+	for (i = 0; i < 4; i++) {
+		v = 0;
+		n = 0;
+		while (*s >= '0' && *s <= '9') {
+			v = v * 10 + (*s++ - '0');
+			if (++n > 3 || v > 255)
+				return 0;
+		}
+		if (!n)
+			return 0;
+		dns_state.addr[i] = v;
+		if (i < 3 && *s++ != '.')
+			return 0;
+	}
+	return !*s;
+}
+
+
+static void dns_next(void) __reentrant
+{
+	uint8_t k = 0;
+
+	if (dns_state.conn) {
+		uip_udp_remove(dns_state.conn);
+		dns_state.conn = 0;
+	}
+	if (dns_used(dns_state.server[0]))
+		dns_cand[k++] = dns_state.server[0];
+	if (dns_used(dns_state.server[1]))
+		dns_cand[k++] = dns_state.server[1];
+	if (dns_used(dhcp_state.dns))
+		dns_cand[k++] = dhcp_state.dns;
+	if (!k || dns_state.tries >= DNS_TRIES) {
+		dns_state.status = DNS_FAILED;
+		if (dns_state.verbose)
+			print_string(k ? "DNS: no answer\n" : "DNS: no server\n");
+		return;
+	}
+	k = dns_state.tries % k;
+	uip_ipaddr(dns_ip, dns_cand[k][0], dns_cand[k][1], dns_cand[k][2], dns_cand[k][3]);
+	dns_state.conn = uip_udp_new(&dns_ip, HTONS(DNS_PORT));
+	if (!dns_state.conn) {
+		dns_state.status = DNS_FAILED;
+		print_string("DNS: no free UDP connection\n");
+		return;
+	}
+	dns_state.send = 1;
+}
+
+
+static void dns_query(void) __reentrant
+{
+	__xdata uint8_t *p = (__xdata uint8_t *)uip_appdata;
+	__xdata char *n = dns_state.name;
+	__xdata uint8_t *label;
+	uint16_t len = 12;
+
+	dns_state.id++;
+	p[0] = dns_state.id >> 8;
+	p[1] = dns_state.id;
+	p[2] = 0x01;
+	p[3] = 0x00;
+	p[4] = 0;
+	p[5] = 1;
+	p[6] = p[7] = p[8] = p[9] = p[10] = p[11] = 0;
+	while (*n) {
+		label = p + len++;
+		*label = 0;
+		while (*n && *n != '.') {
+			p[len++] = *n++;
+			(*label)++;
+		}
+		if (*n)
+			n++;
+	}
+	p[len++] = 0;
+	p[len++] = 0;
+	p[len++] = 1;
+	p[len++] = 0;
+	p[len++] = 1;
+	uip_udp_send(len);
+}
+
+
+static uint16_t dns_skip_name(__xdata uint8_t *p, uint16_t i, uint16_t len) __reentrant
+{
+	while (i < len) {
+		if (!p[i])
+			return i + 1;
+		if ((p[i] & 0xc0) == 0xc0)
+			return i + 2;
+		i += p[i] + 1;
+	}
+	return len;
+}
+
+
+static void dns_answer(void) __reentrant
+{
+	__xdata uint8_t *p = (__xdata uint8_t *)uip_appdata;
+	uint16_t len = uip_datalen();
+	uint16_t i, an;
+
+	if (dns_state.status != DNS_PENDING || len < 12 || !(p[2] & 0x80)
+	    || p[0] != (uint8_t)(dns_state.id >> 8) || p[1] != (uint8_t)dns_state.id)
+		return;
+	an = ((uint16_t)p[6] << 8) | p[7];
+	i = dns_skip_name(p, 12, len) + 4;
+	while (!(p[3] & 0x0f) && an-- && i + 10 <= len) {
+		i = dns_skip_name(p, i, len);
+		if (i + 10 > len)
+			break;
+		if (!p[i] && p[i + 1] == 1 && !p[i + 8] && p[i + 9] == 4 && i + 14 <= len) {
+			memcpy(dns_state.addr, p + i + 10, 4);
+			dns_state.status = DNS_DONE;
+			uip_udp_remove(dns_state.conn);
+			dns_state.conn = 0;
+			if (dns_state.verbose) {
+				print_string("DNS: ");
+				print_string_x(dns_state.name);
+				print_string(" is ");
+				print_ip(dns_state.addr);
+				write_char('\n');
+			}
+			return;
+		}
+		i += 10 + (((uint16_t)p[i + 8] << 8) | p[i + 9]);
+	}
+	dns_state.tries = DNS_TRIES;
+	dns_next();
+}
+
+
+void dns_init(void) __banked
+{
+	memset(dns_state.server, 0, sizeof(dns_state.server));
+	dns_state.name[0] = 0;
+	dns_state.status = DNS_IDLE;
+	dns_state.conn = 0;
+}
+
+
+void dns_lookup(void) __banked
+{
+	if (dns_name_is_ip()) {
+		dns_state.status = DNS_DONE;
+		return;
+	}
+	dns_state.tries = 0;
+	dns_state.status = DNS_PENDING;
+	dns_next();
+}
+
+
+void dns_show(void) __banked
+{
+	print_string("DNS servers ");
+	print_ip(dns_state.server[0]);
+	write_char(' ');
+	print_ip(dns_state.server[1]);
+	print_string(", from DHCP ");
+	print_ip(dhcp_state.dns);
+	write_char('\n');
+	if (!dns_state.name[0])
+		return;
+	print_string("Last lookup ");
+	print_string_x(dns_state.name);
+	print_string(": ");
+	if (dns_state.status == DNS_DONE)
+		print_ip(dns_state.addr);
+	else if (dns_state.status == DNS_PENDING)
+		print_string("pending");
+	else
+		print_string("failed");
+	write_char('\n');
+}
+
+
+void dns_callback(uint16_t lport) __banked __reentrant
+{
+	if (!dns_state.conn || lport != dns_state.conn->lport)
+		return;
+	if (uip_newdata()) {
+		dns_answer();
+		return;
+	}
+	if (dns_state.status != DNS_PENDING)
+		return;
+	if (dns_state.send) {
+		dns_state.send = 0;
+		dns_state.sent = ticks;
+		dns_query();
+		return;
+	}
+	if (ticks - dns_state.sent >= DNS_TIMEOUT) {
+		dns_state.tries++;
+		dns_next();
+	}
+}

dns.h

@@ -0,0 +1,36 @@
+#ifndef _DNS_H_
+#define _DNS_H_
+
+#include <stdint.h>
+
+#define DNS_NAME_LEN	48
+
+#define DNS_IDLE	0
+#define DNS_PENDING	1
+#define DNS_DONE	2
+#define DNS_FAILED	3
+
+struct uip_udp_conn;
+
+struct dns_state {
+	uint8_t server[2][4];	/* configured servers, 0.0.0.0 = unused */
+	char name[DNS_NAME_LEN];	/* name of the current or last lookup */
+	uint8_t addr[4];	/* address found by the last lookup */
+	uint8_t status;		/* DNS_* */
+	uint8_t verbose;	/* print the result of the lookup */
+	uint8_t tries;		/* queries sent for the current lookup */
+	uint8_t send;		/* a query is due on the connection */
+	uint16_t id;
+	uint32_t sent;		/* ticks when the last query went out */
+	struct uip_udp_conn *conn;
+};
+
+extern __xdata struct dns_state dns_state;
+
+void dns_init(void) __banked;
+void dns_lookup(void) __banked;
+void dns_show(void) __banked;
+void dns_callback(uint16_t lport) __banked __reentrant;
+void dns_parse(void) __banked __reentrant;
+
+#endif

dns_cli.c

@@ -0,0 +1,63 @@
+/*
+ * Command line interface of the DNS resolver for the RTL837x platform
+ * This code is in the Public Domain
+ */
+
+#include <stdint.h>
+#include "rtl837x_common.h"
+#include "cmd_parser.h"
+#include "dns.h"
+
+#pragma codeseg BANK2
+#pragma constseg BANK2
+
+extern __xdata uint8_t cmd_buffer[CMD_BUF_SIZE];
+extern __xdata uint8_t cmd_words_len;
+extern __xdata uint8_t cmd_words_b[15];
+extern __xdata uint8_t ip[4];
+uint8_t cmd_compare(uint8_t start, __code const uint8_t * cmd);
+uint8_t parse_ip(uint8_t idx);
+
+
+void dns_parse(void) __banked __reentrant
+{
+	__xdata uint8_t *s;
+	uint8_t n;
+
+	if (cmd_words_len < 2) {
+		dns_show();
+		return;
+	}
+	if (cmd_compare(1, "server") && cmd_words_len >= 3 && parse_ip(cmd_words_b[2])) {
+		memcpy(dns_state.server[0], ip, 4);
+		memset(dns_state.server[1], 0, 4);
+		if (cmd_words_len >= 4) {
+			if (!parse_ip(cmd_words_b[3]))
+				goto err;
+			memcpy(dns_state.server[1], ip, 4);
+		}
+		return;
+	}
+	if (cmd_compare(1, "lookup") && cmd_words_len >= 3) {
+		if (dns_state.status == DNS_PENDING) {
+			print_string("DNS: a lookup is already running\n");
+			return;
+		}
+		s = &cmd_buffer[cmd_words_b[2]];
+		for (n = 0; s[n] && s[n] != ' '; n++) {
+			if (n == DNS_NAME_LEN - 1)
+				goto err;
+			dns_state.name[n] = s[n];
+		}
+		dns_state.name[n] = 0;
+		dns_state.verbose = 1;
+		dns_lookup();
+		if (dns_state.status == DNS_DONE) {
+			print_ip(dns_state.addr);
+			write_char('\n');
+		}
+		return;
+	}
+err:
+	print_string("Error: dns [server <ip> [<ip>]|lookup <name>]\n");
+}

doc/devices/2M-PCB23-V3_2.md

@@ -0,0 +1,40 @@
+### 2M-PCB23-V3.2
+
+## Brands
+|Brand|Type|Managed|PCB|Flash|Chip RTL|
+|---|---|---|---|---|---|
+| keepLINK | KP-9000-9XHML-X | Yes|  2M-PCB23-V3.2 | 2M (Winbond 25Q) | |
+
+The original web interface reports this board as hardware version V3.2
+(original firmware V100.9.25, January 2026).
+
+## PCB
+
+<img src="photos/2M-PCB23-V3.2-managed/2M-PCB23-V3.2-top.jpeg" width="300" />
+
+## Compared to V3.1
+
+The component placement matches [2M-PCB23-V3.1](2M-PCB23-V3_1.md): same
+positions for the flash (U8), the T7/T8/T9/T10 headers, the SFP cage and its
+LED, and the unpopulated U7/U9 footprints. Build with
+`MACHINE=KP_9000_9XHML_X_V3_2`, which uses the V3.1 machine definition and
+only differs in the reported name.
+
+## Tested
+
+Installed from the original firmware through its web interface with
+`installer/output/rtlplayground_oem_upgrade.bin`, then:
+
+- RJ45 ports link at 2.5G; LEDs: orange at 2.5G, green below
+- SFP port: module detected with vendor/model/serial and DOM readings
+  (temperature, Vcc, TX bias, TX/RX power), link up at 10G
+- factory MAC read from flash (0x1FC000)
+- reset button (GPIO48): held for more than 10 s it restores the default config
+
+## Flash access
+
+Reading the flash in-circuit with a SOIC-8 clip did not work: the chip ID
+comes back as `EF FF FF` (only the manufacturer byte is right) and reads
+return 0xff, the same as on a V3.1 board. The switch chip is powered through
+the clip and keeps driving the SPI lines. Make sure a way back is acceptable
+before installing, or hold the switch chip in reset while reading.

doc/devices/F7008-2.5.md

@@ -0,0 +1,70 @@
+# F7008-2.5
+
+Documentation for the unmanaged 8 + 1 switch sold as `7018-2.5G` by Guangnianwei
+(光年微), board marking `F7008-2.5`, PCB `F7008-2.5GPOE-V1.2`.
+
+### Brands
+
+| Brand | Type | Managed | PCB | Flash | Chip RTL |
+|-------|------|---------|-----|-------|----------|
+| Guangnianwei (光年微) | 7018-2.5G | No | F7008-2.5GPOE-V1.2 | W25Q64JVSSIQ | 8373N + 8224N |
+
+### What works
+
+- All eight 2.5GBASE-T RJ45 ports at 10/100/1000/2500 Mbps
+- SFP+ port with 1G/2.5G/10G modules
+- LEDs of the eight RJ45 ports
+
+### Not verified
+
+- The LED pads for the SFP+ cage are not mapped yet. The SFP+ lamps are left
+  undriven, so an inserted module lights nothing.
+- The UART header footprint is present but unpopulated, and no boot log could be
+  captured from it, so the baud rate is unknown. There are most likely
+  unpopulated 0-Ohm resistors next to the header; bridging those should bring
+  the console to life.
+
+### Build target
+
+```
+make MACHINE=F7008_2_5
+```
+
+### LED wiring
+
+Measured pad to lamp map (`led_mux` index -> lamp):
+
+| Port | green lamp | yellow lamp |
+|------|-----------|-------------|
+| 1 | pad 0  | pad 1  |
+| 2 | pad 2  | pad 3  |
+| 3 | pad 4  | pad 5  |
+| 4 | pad 6  | pad 8  |
+| 5 | pad 9  | pad 10 |
+| 6 | pad 12 | pad 15 |
+| 7 | pad 18 | pad 21 |
+| 8 | pad 24 | pad 25 |
+
+Pads 7, 11, 13, 14, 16, 17, 19, 20, 22, 23, 26 and 27 do not drive an RJ45 lamp.
+
+The front panel is silkscreened `2.5G: Green / 10/100M: Yellow`, and the target
+follows it: the green lamp is on while the port is linked at 2.5G, the yellow
+lamp blinks while data is flowing.
+
+### PCB overview
+
+The board is marked `F7008-2.5GPOE-V1.2`.
+
+Top side:
+
+<img src="photos/F7008-2.5/PCB-top.jpg" width="600" />
+
+Bottom side:
+
+<img src="photos/F7008-2.5/PCB-bottom.jpg" width="600" />
+
+### Hardware notes
+
+- 4 x `RT4802SNE` magnetics
+- Unpopulated UART header footprint, next to the magnetics
+- Power input 12V 1A, 180 x 84 x 29 mm metal case

doc/devices/HASIVO_S1100WP_8GT_1SX_SE.md

@@ -0,0 +1,75 @@
+# Hasivo S1100WP-8GT-1SX-SE
+
+RTL8373-based 8×2.5G PoE + 1×SFP switch.
+
+### Label specifications
+
+- **Manufacturer**: Hasivo
+- **Model**: S1100WP-8GT-1SX-SE
+- **Ports**:
+  - 8 × RJ45: 10/100/1000/2500 Mbps with PoE
+  - 1 × SFP: 1G / 2.5G / 10G
+- **Power input**: DC 52V 2.5A
+- **Stock firmware defaults**: IP 192.168.0.1, user/password `admin`/`admin`
+
+### What works
+
+- All eight 2.5GBASE-T RJ45 ports at 10/100/1000/2500 Mbps (PoE is not configurable via RTLPlayground)
+- SFP port supporting 1G, 2.5G and 10G modules
+- LEDs: green (2.5G) and amber (1G/100M/10M) per copper port; combined link/act on the SFP port
+
+### Photos
+
+Front panel:
+
+<img src="photos/HASIVO_S1100WP-8GT-1SX-SE/front.jpg" width="600" />
+
+Label:
+
+<img src="photos/HASIVO_S1100WP-8GT-1SX-SE/label.jpg" width="600" />
+
+### PCB overview
+
+Top side:
+
+<img src="photos/HASIVO_S1100WP-8GT-1SX-SE/pcb_top.jpg" width="600" />
+
+Bottom side:
+
+<img src="photos/HASIVO_S1100WP-8GT-1SX-SE/pcb_bottom.jpg" width="600" />
+
+### Port layout
+
+| Logical port | Physical port | Type   |
+|--------------|---------------|--------|
+| 1-8          | 1-8           | Copper |
+| 9            | 9             | SFP    |
+
+### LED configuration
+
+Copper ports use LED SET0, the SFP port uses LED SET1.
+
+| SET  | LED0                                          | LED2                                                 |
+|------|-----------------------------------------------|------------------------------------------------------|
+| SET0 | Green — lights on 2.5G link with activity     | Amber — lights on 1G / 100M / 10M link with activity |
+| SET1 | All speeds — lights on any link with activity | —                                                    |
+
+### SFP GPIO assignments
+
+| SFP (logical 9) | pin_detect (ModAbs) | pin_los | pin_tx_disable | SerDes | I2C SDA         | I2C SCL             |
+|-----------------|---------------------|---------|----------------|--------|-----------------|---------------------|
+| SFP             | GPIO30_ACL_BIT3_EN  | GPIO37  | GPIO_NA        | SDS1   | GPIO39_I2C_SDA4 | GPIO40_I2C_SCL3_MDC1 |
+
+### Machine configuration
+
+- `reset_pin`: GPIO54_ACL_BIT2_EN
+- High LEDs (pads 27-29): mux = `LED_27 | LED_28_SYS | LED_29`, enable = `LED_28_SYS | LED_29`
+
+### PoE
+
+The 8 copper ports support PoE powered by a DC 52V 2.5A input. Power management is handled by two HS104PTI chipsets over I2C (GPIO47_I2C_SDA0, GPIO46_I2C_SCL0):
+
+* Chip 1 (I2C address 0x1A): 2.5G Ports 1–4
+* Chip 2 (I2C address 0x2A): 2.5G Ports 5–8
+
+Note: The current implementation does not yet support PoE management. Consequently, PoE currently operates in standalone mode without software control.

doc/devices/ONT-S207CW-62TS-SE.md

@@ -0,0 +1,122 @@
+# ONT-S207CW-62TS-SE / Binardat 2G06-04210GSM / Binardat 2G06-04210GS
+
+## Overview
+
+ONT-S207CW-62TS-SE, Binardat 2G06-04210GSM (managed), and Binardat 2G06-04210GS (unmanaged) are **switches with identical hardware**:
+- **CPU:** RTL8372N (confirmed via serial: "Detecting CPU: RTL8372N")
+- **Flash:** GD25Q128E (16MB)
+- **Ports:** 4x 2.5G RJ45 + 2x 10G SFP+
+- **Console:** 115200 baud (RTLPlayground firmware) / 9600 baud (stock firmware)
+
+**Note:** These devices are **RTL8372N-based** with **LAN ports mounted upside-down on the PCB**, requiring a custom configuration. The `MACHINE_ONT_S207CW_62TS_SE` definition uses a **custom configuration** with:
+- Corrected port mapping (physical ports 1-4 = RJ45, 5-6 = SFP)
+- Optimized LED sets for different port wiring (RJ45 Ports 1-2 have reversed LED wiring)
+- Custom LED mux configuration
+
+## Device Photos
+
+### Binardat 2G06-04210GSM
+
+**Front View:**
+<img src="photos/ONT-S207CW-Binardat-2G06-04210GSM/binardat-2g06-04210gsm-front.jpg" width="400" />
+
+**Back View:**
+<img src="photos/ONT-S207CW-Binardat-2G06-04210GSM/binardat-2g06-04210gsm-back.jpg" width="400" />
+
+**PCB View:**
+<img src="photos/ONT-S207CW-Binardat-2G06-04210GSM/binardat-2g06-04210gsm-pcb.jpg" width="400" />
+
+*Photos courtesy of [andreas5232](https://github.com/andreas5232) from [emesix/ONT-S207CW-62TS-SE#1](https://github.com/emesix/ONT-S207CW-62TS-SE/issues/1)*
+
+## Hardware Specification
+
+| Feature | Value |
+|---|---|
+| **CPU** | RTL8372N |
+| **Flash** | GD25Q128E (16MB) |
+| **RAM** | Integrated in RTL8372N |
+| **RJ45 Ports** | 4x 2.5GBase-T (Ports 1-4) |
+| **SFP+ Ports** | 2x 10G (Ports 5-6) |
+| **Console** | UART (115200 baud for RTLPlayground, 9600 baud for stock) |
+| **Stock Web UI IP** | 192.168.2.1 |
+| **Loader Mode IP** | 192.168.10.247 |
+
+## Port Layout
+
+```
+┌─────────────────────────────────────────────┐
+│  ┌─────┐ ┌─────┐ ┌─────┐ ┌─────┐   ┌─────┐ ┌─────┐  │
+│  │RJ45 │ │RJ45 │ │RJ45 │ │RJ45 │   │SFP+ │ │SFP+ │  │
+│  │  1  │ │  2  │ │  3  │ │  4  │   │  5  │ │  6  │  │
+│  └─────┘ └─────┘ └─────┘ └─────┘   └─────┘ └─────┘  │
+│                                                     │
+│  [System LEDs]                                      │
+└─────────────────────────────────────────────┘
+```
+
+## LED Behavior
+
+### RJ45 Ports (Physical 1-4)
+
+| LED Color | Speed |
+|---|---|
+| **Green** | 2.5G |
+| **Orange** | 1G / 100M / 10M |
+| **Off** | No link |
+
+### SFP+ Ports (Physical 5-6)
+
+| LED Color | Speed |
+|---|---|
+| **Green** | 10G |
+| **Orange** | 2.5G / 1G |
+| **Off** | No link / No SFP module |
+
+## Port to Logical Mapping
+
+Custom mapping for ONT-S207CW-62TS-SE:
+
+| Physical Port | Logical Port | Type | LED Set |
+|---|---|---|---|
+| 1 | 7 | RJ45 | 2 |
+| 2 | 6 | RJ45 | 2 |
+| 3 | 5 | RJ45 | 0 |
+| 4 | 4 | RJ45 | 0 |
+| 5 | 3 | SFP+ (SDS0) | 3 |
+| 6 | 8 | SFP+ (SDS1) | 3 |
+
+**Note:** Ports 1-2 (RJ45) have reversed LED wiring and use LED-Set 2. SFP Ports 5-6 use LED-Set 3 to account for wiring differences.
+
+## Flashing Instructions
+
+See the [README.md](../../README.md) for general flashing instructions.
+
+## Stock Firmware Information
+
+| Property | Value |
+|---|---|
+| **Default IP** | 192.168.2.1 (ONT) / 192.168.10.247 (Loader Mode) |
+| **Default Login** | admin/admin (may vary by OEM) |
+| **Console Baud** | 9600 (stock) / 115200 (RTLPlayground) |
+| **CPU String** | "RTL8372N" |
+| **Loader Mode IP** | 192.168.10.247 |
+
+## Configuration Details
+
+- **CPU:** RTL8372N
+- **SFP:** SDS0 on logical port 3 (GPIO37), SDS1 on logical port 8 (GPIO38)
+- **Port Mapping:** Physical 1-4 → Logical 7-4, Physical 5-6 → Logical 3,8
+- **LED Wiring:** RJ45 Ports 1-2 and SFP Port 6 have reversed LED pins (orange/green swapped)
+- **LED Sets:** Set 0 for RJ45 Ports 3-4, Set 1 unused, Set 2 for RJ45 Ports 1-2, Set 3 for SFP Ports 5-6
+
+## Notes
+
+- ONT-S207CW-62TS-SE, Binardat 2G06-04210GSM (managed), and Binardat 2G06-04210GS (unmanaged) are **RTL8372N-based** with **LAN ports mounted upside-down on the PCB**
+- Web UI shows correct physical port order (1-2-3-4 for RJ45, 5-6 for SFP)
+- Loader Mode always remains accessible at `192.168.10.247` for recovery
+- Serial console: 9600 baud (stock) → 115200 baud (RTLPlayground)
+
+## References
+
+- [GitHub Issue: emesix/ONT-S207CW-62TS-SE#1](https://github.com/emesix/ONT-S207CW-62TS-SE/issues/1) - Original photos and discussion
+- [PR: logicog/RTLPlayground#465](https://github.com/logicog/RTLPlayground/pull/465) - Feedback and improvements

doc/devices/SWTG018AS_A_V2_0.md

@@ -1,9 +1,10 @@
 # SWTG018AS-A V2.0
 ## Brands
-| Brand  | Type             |Managed| PCB              | Flash           | Chip RTL      |
-|--------|------------------|-------|------------------|-----------------|---------------|
-| Ampcom | SWTG018AS-A V2.0 | No    | SWTG018AS-A V2.0 | 2MB             | 8273N + 8224N |
-| Horaco | HC-SWTGW218AS-A  | Yes   | SWTG018AS-A V2.0 | 2MB(25Q16JVSIQ) | 8273N + 8224N |
+| Brand   | Type             |Managed| PCB              | Flash           | Chip RTL      |
+|---------|------------------|-------|------------------|-----------------|---------------|
+| Ampcom  | SWTG018AS-A V2.0 | No    | SWTG018AS-A V2.0 | 2MB             | 8273N + 8224N |
+| Horaco  | HC-SWTGW218AS-A  | Yes   | SWTG018AS-A V2.0 | 2MB(25Q16JVSIQ) | 8273N + 8224N |
+| GoodTop | GT-ST018M        | Yes   | SWTG018AS-A V2.0 | ?               | 8273N + 8224N |
 
 
 The following is a documentation for the unmanaged switch marked as `SWTG018AS-A V2.0`.

doc/dns.md

@@ -0,0 +1,23 @@
+# DNS
+
+The switch can resolve host names to IPv4 addresses, for the NTP client and
+for anything else that is given a name instead of an address.
+
+```
+dns server <ip> [<ip>]   # one or two servers, 0.0.0.0 removes them
+dns lookup <name>        # resolve a name and print the address
+dns                      # show the servers and the last lookup
+```
+
+The answer to a lookup arrives after the command has returned, so it is
+printed on the serial console and in the syslog. In the console of the web
+interface, run `dns` afterwards to see it.
+
+Without a configured server the resolver uses the one handed out by DHCP.
+Only address records are looked up; a query goes to the servers in turn,
+every two seconds, and gives up after six tries. A name that already is a
+dotted address is taken as it is, without a query.
+
+The DNS servers are set in the Network card of the System page as well.
+Settings made there or on the console are kept only once the configuration is
+saved.

doc/health.md

@@ -0,0 +1,79 @@
+# The health command
+
+`health` prints a one-page snapshot of the firmware's vital signs on the
+serial console. It exists for the situations where the switch misbehaves and
+every probe from the network measures the network instead of the device: the
+dump is taken from inside, costs one command, and works while HTTP does not.
+
+```
+> health
+up 0000001f ticks 0x00001f4c loops 0x000016da rx 0x024e
+link max 01 slow 0x0000
+sfp  max 74 slow 0x0001
+rx   max 00 slow 0x0000
+tx   max 00 slow 0x0000
+stp  max 04 slow 0x0001
+cmd  max 02 slow 0x0001
+sp 80 untouched 62
+tcp st 00 tmr 00 rtx 00 rto 00 len 0x0000 mss 0x05b4
+  lport 0x0000 rport 0x0000 rip 0x0000 0x0000
+httpd left 0x0000 entry 00 stp 01 mvlan 0x0002
+```
+
+The instrumentation is not part of a default build. It costs about 1.1 kB
+of bank 2, a few bytes of xdata and seven banked calls per main-loop pass,
+which is nothing a user needs unless they are chasing a problem, so it is
+switched on at build time:
+
+```
+make MACHINE=SWTGW218AS HEALTH=1
+```
+
+Without it the hooks compile to nothing and `health` is not a command.
+
+All figures are raw hex. The counters are cumulative: take two dumps a known
+time apart and the differences give the rates.
+
+## The first line
+
+`up` is the seconds counter, `ticks` the system tick (200 per second),
+`loops` the number of main-loop passes and `rx` the frames handle_rx has
+taken off the NIC. A healthy loop completes one pass per tick, so the
+difference in `loops` tracks the difference in `ticks`; a loop that falls
+behind is being held up by one of the phases below. The `rx` rate separates
+a flooded CPU port from a stalled loop, which look identical from outside.
+
+## Phases
+
+Each line is one section of the main loop: the link poll, SFP handling,
+frame reception, TCP transmission, the STP timers and the command dispatch.
+`max` is the worst time that section has taken, in ticks of 5 ms; `slow`
+counts the passes that took two ticks or more. A misbehaving subsystem
+names itself here, which is the difference between knowing that the loop is
+slow and knowing why.
+
+A dump of its own output takes the console some milliseconds, so running
+`health` repeatedly increments the `cmd` counters by itself. That is the
+instrument observing itself, not a fault.
+
+## Stack
+
+At boot the free stack area is painted with a pattern. `sp` is the live
+stack pointer; `untouched` counts the painted bytes still intact at the top,
+which is the closest thing to a high-water mark this hardware offers. A
+shrinking `untouched` across dumps means something is reaching deeper than
+anything before it.
+
+## The TCP slot
+
+The connection table is printed whole, one slot per pair of lines: TCP
+state (3 is ESTABLISHED, 0 closed), retransmission timer and counter, bytes
+in flight, negotiated MSS, then the ports and the peer address. With a
+single slot serving the entire web interface, one glance answers the
+question every management outage starts with: who is holding it. A slot
+showing state 3 with nothing in flight and a peer that no longer answers is
+a connection whose owner went away.
+
+`httpd left` and `entry` describe the file transfer the web server believes
+it is in the middle of, and the trailing flags show whether STP is running
+and which VLAN carries management.

doc/igmp.md

@@ -69,18 +69,26 @@ The code currently provides the following functions:
 void igmp_setup(void) __banked;
 void igmp_enable(void) __banked;
 void igmp_router_port_set(uint16_t pmask) __banked;
-void igmp_packet_handler(void) __banked;
+uint8_t igmp_packet_handler(void) __banked;
 void igmp_show(void) __banked;
 ```c
 `igmp_setup()` is called at boot-time and configures flooding of all IP-MC packets by
-default, as otherwise no IP-MC would be possible in the network.
+default, as otherwise no IP-MC would be possible in the network. `igmp off` calls it as
+well; groups learned while IGMP was on stay in the table, but are no longer looked up.
 
 `igmp_enable()`starts IGMP which cause IGMP packets to be handled by the CPU and forwarding
 of IP-MC packets to be limited to only subscribed ports.
 
 `igmp_router_port_set()`configures forwarding ports for IGMP messages.
 
-`igmp_packet_handler()` implements handling of trapped IGMP packets by the CPU.
+`igmp_packet_handler()` implements handling of trapped IGMP packets by the CPU. It is called
+for frames to 01:00:5e:xx:xx:xx and returns 0 when the frame is not a trapped IGMP packet,
+so that it is passed on to the IP stack. IGMPv1/v2 reports (0x12, 0x16) join the group given
+in the IGMP header, IGMPv2 leaves (0x17) leave it, IGMPv3 reports use the first group record
+(type 4 joins, type 3 leaves). Trapped IGMP frames arrive without a VLAN tag.
+Reports for groups in 224.0.0.0/24 are ignored: the switch floods that block
+even with IGMP on, and an entry for a group such as 224.0.0.251 (mDNS) would
+otherwise limit it to the ports that reported it, as RFC 4541 warns against.
 
 `igmp_show()` prints out the IGMP configuration on the CLI.
 

doc/l2.md

@@ -73,13 +73,14 @@ without being flooded to the other ports. No bridge relays these frames:
 their addresses are in the set that 802.1D-2004 clause 7.12.6 forbids a
 bridge to forward, and what travels the network is the information, with
 every bridge regenerating BPDUs of its own on its designated ports. The reserved-multicast *trap* action
-cannot do that on this hardware, because its destination is an external CPU
-attached to a physical port, which these boards do not populate. The protocol
-modules therefore leave the reserved-multicast action at *forward* and constrain
-the egress with a static L2 multicast entry instead: the lookup hits the entry's
-own port mask rather than the VLAN flood mask. Verified on a SWTGW218AS both
-ways, with the CPU bit cleared, where delivery stops, and with the CPU bit alone,
-where nothing egresses.
+does that: it delivers to the port named in `EXT_CPU_CTRL` (0x6724), which
+`trap_init()` sets to 9, the CPU port, at startup; with the reset value 0xf it
+names no port and the trapped frame is dropped. STP traps its address while it
+runs (see stp.md). Where the action is left at *forward*, the egress can be
+constrained with a static L2 multicast entry instead: the lookup hits the
+entry's own port mask rather than the VLAN flood mask. Verified on a SWTGW218AS
+both ways, with the CPU bit cleared, where delivery stops, and with the CPU bit
+alone, where nothing egresses.
 
 `port_l2mc_set()` writes one such entry. The SMI layout is the L2 multicast
 variant of the table entry:

doc/lacp.md

@@ -0,0 +1,155 @@
+# LACP (Link Aggregation Control Protocol, IEEE 802.3ad)
+
+A static link aggregation group works only if both ends are configured for the
+same links, and nothing checks that they are. LACP lets the two ends agree on
+which links reach the same partner, aggregates only those, and takes a link out
+of the group when the partner stops answering.
+
+The switch runs LACP in software on the 8051. LACP frames belong to the Slow
+Protocols, with destination `01:80:C2:00:00:02` and ethertype `0x8809`; the
+subtype of LACP frames is 1. The implementation has the Receive, Selection and
+Mux machines of 802.3ad clause 43 and does not aggregate links whose partners
+differ. Up to `LACP_NUM_LAGS` (4) groups can run LACP; the others stay static.
+
+## Getting the frames to the CPU
+
+While LACP runs, the reserved multicast action for `01:80:C2:00:00:02` is
+*trap*, the same mechanism STP uses for its BPDUs, see [stp.md](stp.md). A
+trapped LACPDU has no VLAN tag after the RTL tag, and `TRAP_RX_BODY()` gives the
+offset of the LACPDU in the received frame. When the last group leaves LACP,
+the action goes back to *drop*.
+
+## What has to match across the members
+
+802.3ad requires that every link in an aggregate be full duplex and run at the
+same speed. Beyond the standard, anything that changes how a frame is treated
+has to be identical across members, because the hash picks the member per frame
+and a difference would make the behaviour depend on that choice:
+
+* must match: speed and duplex, VLAN membership and pvid, ingress filtering,
+  port isolation
+* may differ: EEE, LED configuration, counters, cable diagnostics
+
+None of this is enforced yet — `port_lag_members_set()` writes a member mask and
+a hash setting and validates nothing. See #377 for the discussion of whether a
+mismatch should be rejected or applied to the whole group.
+
+## Protocol timing
+
+The timer values are in units of the LACP timer, which steps every four ticks
+of the system clock, 50 times per second:
+
+| Constant             | Value | Time |
+|----------------------|-------|------|
+| `LACP_FAST_PERIODIC` | 50    | 1 s  |
+| `LACP_SLOW_PERIODIC` | 1500  | 30 s |
+| `LACP_SHORT_TIMEOUT` | 200   | 4 s  |
+
+802.3ad specifies a fast periodic time of 1 s with a short timeout of 3 s, and a
+slow periodic time of 30 s with a long timeout of 90 s. The switch transmits at
+the rate the partner asks for with its TIMEOUT bit. Its own timeout is always
+the short one, one second above the standard, so a partner that stops sending
+while its link stays up leaves the trunk after 4 s.
+
+The Partner block of a transmitted LACPDU repeats the partner's actor
+information as it was last received: system priority, system, key, port
+priority, port and state. A Linux partner sets our SYNC only when this block
+matches what it sent.
+
+## LACP API
+
+```
+void lacp_init(void) __banked;
+void lacp_off(void) __banked;
+void lacp_lag_set(uint8_t lag, __xdata uint16_t ports) __banked;
+void lacp_in(void) __banked;
+void lacp_timers(void) __banked;
+void lacp_show(void) __banked;
+```
+
+`lacp_init()` has to run before the startup configuration replays, because xdata
+is not zeroed and the port-to-LAG map uses `0xff` as "no LAG"; a stray zero would
+make a port look like it belongs to LAG 0.
+
+## LACP configuration on the serial console
+
+A group is put under LACP by adding `lacp` to the `lag` command:
+
+```
+lag 1 lacp 7 8      # ports 7 and 8 become LACP candidates of group 1
+lag 1 lacp off      # group 1 leaves LACP, its trunk is cleared (so does "lag 1 lacp")
+lag 1 d             # group 1 disabled, whether it ran LACP or not
+lag 1 7 8           # plain static aggregation, no protocol
+```
+
+A group put under LACP gives up the static trunk it had: the hardware trunk is
+cleared and rebuilt from the ports that converge. The other way round, `lag 1 d`
+and a static member list take the group out of LACP before they touch the
+trunk. A port named in another LACP group moves to the new one. The protocol
+starts with the first group put under LACP and stops when the last one is taken
+out; there is no separate switch for it. Two commands act on the whole engine:
+
+```
+lacp off            # every group leaves LACP, protocol stopped
+lacp show
+```
+
+`lacp show` prints the engine state, then one line per group with its candidate
+ports, the elected aggregator and the trunk members actually programmed into the
+hardware, then one line per port with the actor and partner state bytes and the
+receive-machine state.
+
+## LACP configuration via the Web Interface
+
+Each group on the LAG page has a Static/LACP mode next to its member ports;
+for an LACP group it shows the elected aggregator and the active members. Below
+the groups a table has one row per LACP port with its group, actor and partner
+state, receive state, LACPDU count and partner system. The page reads
+`/lacp.json` every three seconds while it is open. The member checkboxes of a
+static group come from the hardware registers in `/lag.json`.
+
+## A test with a Linux 802.3ad bond
+
+Two ports of the switch to two interfaces of one host:
+
+```
+ip link add bond0 type bond mode 802.3ad
+ip link set enp1s0 down && ip link set enp1s0 master bond0
+ip link set enp2s0 down && ip link set enp2s0 master bond0
+ip link set bond0 up
+```
+
+On the switch, with those two ports as the group:
+
+```
+lag 1 lacp 7 8
+```
+
+`lacp show` should then give both ports an actor state of `0x3f` (ACTIVITY,
+TIMEOUT, AGGREGATION, SYNC, COLLECTING and DISTRIBUTING), a partner state with
+SYNC set, and the partner's system MAC. `lag show` lists the trunk members as
+programmed in the hardware and should show both ports.
+
+On the host, `/proc/net/bonding/bond0` should show the same `Aggregator ID` for
+both slaves; different IDs mean that each link is in a group of its own. Both
+churn states should read `none`.
+
+Further checks:
+
+* `tcpdump -i enp1s0 ether proto 0x8809` on each slave shows the LACPDUs of the
+  switch and of that slave, never those of the other slave.
+* The host log has no `illegal loopback`.
+* The three reserved bytes after the actor state in a LACPDU from the switch
+  are zero.
+
+When one slave goes down, the group narrows to the remaining member, and the
+slave rejoins after it comes back.
+
+## Known limits
+
+* No Churn Detection machines and no Marker protocol.
+* Coupled Mux: collecting and distributing are enabled together.
+* One aggregator per group.
+* Selection compares the partner's system only, not its key: two aggregates
+  that one partner system offers on the same group land in one trunk here.
+* Member compatibility is not validated; see #377.

doc/link_aggregation.md

@@ -227,3 +227,7 @@ iperf Done.
 ```
 As you can see, the total throughput was 4.71 GBit/sec which is close to the
 maximum possible with a single 5GBit link.
+
+## LACP
+
+Dynamic aggregation with LACP is described in [lacp.md](lacp.md).

doc/ntp.md

@@ -0,0 +1,33 @@
+# Time
+
+The switch has no battery backed clock. It counts seconds from power on, and
+it can take the date and time from an NTP server once the network is up. The
+time is lost at every restart and set again at the first synchronisation.
+
+```
+ntp server <name|ip>     # default pool.ntp.org
+ntp interval <1-1440>    # minutes between two synchronisations, default 60
+ntp timezone <+hh:mm>    # offset from UTC, -12:00 to +14:00
+ntp dst off|eu|us        # daylight saving rule
+ntp on
+ntp off
+ntp                      # settings and time
+time                     # local date and time
+```
+
+The client speaks SNTP version 4 and synchronises at once when turned on,
+then after every interval. A server given by name is resolved through the DNS
+resolver before every synchronisation. An answer from an unsynchronised
+server is ignored, and a failed attempt is repeated after 30 seconds.
+
+The local time is UTC plus the time zone offset, plus one hour while daylight
+saving time applies:
+
+* `eu`: from 01:00 UTC on the last Sunday of March to 01:00 UTC on the last
+  Sunday of October;
+* `us`: from 02:00 local time on the second Sunday of March to 02:00 local
+  time on the first Sunday of November.
+
+The same settings, with the current local time and the last synchronisation,
+are in the Time card of the System page. Settings made there or on the
+console are kept only once the configuration is saved.

doc/storm_control.md

@@ -0,0 +1,54 @@
+# Storm Control
+Storm control limits the rate at which a port admits broadcast, multicast,
+unknown unicast and unknown multicast frames. Frames of a type above its limit
+are dropped at ingress, so a loop or a misbehaving host cannot flood the rest
+of the network through that port. Known unicast traffic is not affected.
+
+## Commands
+```
+storm <port> bcast|mcast|ucast|umcast <rate> pps
+storm <port> bcast|mcast|ucast|umcast <rate> kbps
+storm <port> bcast|mcast|ucast|umcast off
+storm
+```
+`ucast` is unicast to a MAC address the switch has not learned yet, and
+`umcast` is multicast without an entry in the address table. Multicast groups
+get their entries from IGMP snooping, so without `igmp on` all multicast is
+unknown and only the `umcast` limit applies to it; `mcast` covers the groups
+IGMP has learned. A limit in
+packets per second goes from 1 to 1048575, a limit in kbit/s from 1 to
+10000000. `storm` without arguments prints the limits of every port. The
+limits are kept in the configuration like any other setting, and the Bandwidth
+page of the web interface has a Storm control card to set them.
+
+## Registers
+Each port and type has an enable bit and a meter index, and each limit uses
+one of the 64 shared meters of the switch. RTLPlayground gives every port and
+type its own meter, index `24 + port * 4 + type`, so one port's storm does not
+eat into the limit of another. Storm control uses meters 24 to 63 and leaves
+0 to 23 to the ACL. The limit of a meter is in `RTL837X_METER_RATE + 4 *
+meter`, and bit `meter % 32` of `RTL837X_METER_MODE + 4 * (meter / 32)`
+selects pps instead of kbit/s.
+```
+#define RTL837X_STORM_CTRL		0x54e4	/* + 4 * type, bit = port */
+#define RTL837X_STORM_MIDX		0x54f4	/* + 8 * type + 4 * (port / 5), 6 bits per port */
+#define RTL837X_METER_RATE		0x5cf0	/* + 4 * meter, 24 bits, kbit/s or pps */
+#define RTL837X_METER_MODE		0x5ef0	/* + 4 * (meter / 32), bit set = pps */
+```
+In kbit/s mode one step of the rate is 1 kbit/s. Measured with 100 and 1000 byte
+frames, the meter counts a frame with its FCS, but without preamble and
+interframe gap. Every meter has a bit that adds them, in `0x5f08 + 4 * (meter
+/ 32)`, which storm control leaves cleared. `IGBW_INC_IFG` and `EGBW_INC_IFG`
+are the matching bits of the bandwidth control.
+
+An ingress bandwidth limit on the same port works on the same arriving frames
+as the storm limit rather than after it, and the two together pass far less
+than either one: a 1 Mbit/s `umcast` limit with a 10 Mbit/s ingress limit let
+0.12 to 0.16 Mbit/s of a 1.4 Gbit/s stream through, where each alone passed
+1.17 and 10.2 Mbit/s.
+
+The type is 0 for broadcast, 1 for multicast, 2 for unknown unicast and 3 for
+unknown multicast. The burst size of a meter (0x5df0 + 4 * meter) counts packets
+in pps mode; its default of 0x2000 lets 8192 frames through before a pps limit
+bites, so a pps limit sets the burst to one second of traffic. A kbit/s limit
+puts back the default.

doc/stp.md

@@ -35,28 +35,34 @@ BPDUs are addressed to `01:80:C2:00:00:00`, a reserved link-local group. The
 ASIC's Reserved-Multicast action for that address decides what happens to the
 frame.
 
-Forwarding to the CPU port works normally: the 8051 sits behind an ordinary
-port of the internal switch and is an ordinary member of a forwarding mask.
-The *trap* action does not deliver to it. Its destination is an external CPU
-attached to a physical port (`cpuTag_externalCpuPort_set`, `EXT_CPU_CTRL` in
-the vendor SDK), which these boards do not populate. The ACL trap and
-redirect actions do not deliver to the 8051 either.
+While STP runs, the action is *trap*. A trap delivers to the port named in
+`EXT_CPU_CTRL` (0x6724), whose reset value 0xf names no port, and with that
+value the trapped frame is dropped at ingress. `trap_init()` sets it to 9, the
+port the 8051 sits behind, once at startup. The trap needs no per-VLAN L2
+entries, so it does not depend on which VLANs exist or on the PVIDs, and turning
+STP on no longer walks the whole VLAN table. BPDUs reach the CPU on a port that
+STP holds in blocking with either action: measured on a SWTGW218AS by sending
+BPDUs into a blocked port with forward and with trap, both ports stopped being
+edge and waited out the forward delay. The chip exempts this address from the
+ingress state check; the slow-protocols address used by LACP is not exempt.
 
-Delivery therefore uses the *forward* action, constrained to the CPU port
-by a static L2 multicast entry (`port_l2mc_set()`), one per VLAN in use:
+A trapped frame reaches the CPU in the format it came in with: unlike a
+forwarded one it has no VLAN tag inserted after the RTL tag, and the RTL tag
+carries the trap reason. `stp_in()` reads the BPDU from the offset
+`TRAP_RX_BODY()` returns, which works for both.
 
-* while STP runs, the entry's member mask is the CPU port only — BPDUs reach
-  the CPU and are not flooded to other ports, as a participating bridge
-  requires;
-* with STP off, the same entries are retargeted to all ports, restoring the
-  transparency an unmanaged switch is expected to have, so a surrounding
-  spanning tree can span *through* this device.
+With STP off, the action goes back to *forward* and a static L2 multicast
+entry per VLAN in use (`port_l2mc_set()`) targets all ports, restoring the
+transparency an unmanaged switch is expected to have, so a surrounding
+spanning tree can span *through* this device.
 
-A BPDU delivered this way is an ordinary frame to the port's ingress logic
-and passes through its acceptable-frame-type filter. BPDUs are untagged, so a
-port set to admit tagged frames only (`ingress <port>t`) never delivers one
-to the CPU. `stp_setup()` prints a warning for every STP-enabled port in that
-state.
+The port's acceptable-frame-type filter treats the two actions differently.
+BPDUs are untagged, so a port set to admit tagged frames only
+(`ingress <port>t`) drops a forwarded BPDU before it reaches the CPU, while a
+trapped one passes. Both were measured on a SWTGW218AS with `ingress 3t`:
+LACPDUs, delivered by forward, stopped arriving on port 3, and BPDUs sent into
+the same port, delivered by trap, kept arriving. A port that admits tagged
+frames only therefore takes part in STP.
 
 ## Link aggregation
 

doc/supported_devices.md

@@ -7,6 +7,8 @@ The following devices have been tested and are fully working:
 | Davuaz   | Da-K6501W       | No      | [PCB-K0501W-V2.0](devices/K0501W_V2_0.md)                                 |       | 5 + 1 |
 | FOXNEO   | FNS-1200P       | No      | [PCB-K0402W-U13-V2.0](devices/FNS-1200P.md)                               | 2M    | 4 + 2 |
 | Goalake  | IG108           | No      | [PB-2132](devices/PB-2132.md)                                             | 4M    | 8 + 1 |
+| GoodTop  | GT-ST018M       | Yes     | [SWTG018AS-A V2.0](devices/SWTG018AS_A_V2_0.md)                           | ?     | 8 + 1 |
+| Hasivo   | S1100WP_8GT_1SX_SE | Yes  | [S1100WP_8GT_1SX_SE-V1.05](devices/HASIVO_S1100WP_8GT_1SX_SE.md)          | 2M    | 8 + 1 |
 | Hisource | Hi-K0402WS      | No      | [PCB-K0402WS-V3.0](devices/PCB-K0402WS-V3.0.md)                           |       | 4 + 2 |
 | Hisource | Hi-K0402WS      | No      | [PCB-K0402WS-V2.0](devices/PCB-K0402WS-V2.0.md)                           | 2M    | 4 + 2 |
 | Hisource | Hi-K0801WS      | No      | [PCB-KO801W-V2.0](devices/HI-K0801WS.md)                                  |       | 8 + 1 |
@@ -20,12 +22,15 @@ The following devices have been tested and are fully working:
 | Keeplink | KP-9000-6XH-X2 / KP-9000-6XHML-X2 | No/Yes | [2M-PCB43-V1.2 / V2.1](devices/KP-9000-6XH-X2.md) |       | 4 + 2 |
 | keepLINK | KP-9000-9XHML-X | Yes     | [2M-PCB23-V2.2](devices/2M-PCB23-V2_2.md)                                 | 2M    | 8 + 1 |
 | keepLINK | KP-9000-9XHML-X | Yes     | [2M-PCB23-V3.1](devices/2M-PCB23-V3_1.md)                                 | 2M    | 8 + 1 |
+| keepLINK | KP-9000-9XHML-X | Yes     | [2M-PCB23-V3.2](devices/2M-PCB23-V3_2.md)                                 | 2M    | 8 + 1 |
 | LIANGUO  | SWTG024AS       | No      | [SWTG024AS-v2.0-17452](devices/SWTG024AS.md)                              | 0.5M  | 4 + 2 |
 | Lianguo  | ZX-SWTGW215AS   | Yes     | [PCB-SWTG115AS-V2.0 / PCB-SWTG115AS-V2.1](devices/SWTGW215AS.md)          | 2M    | 5 + 1 |
 | Lianguo  | HYWS-SGT0108S   | No      | [2G5F_20G_V1.01](devices/HYWS-SGT0108S.md)                                | 0.5M  | 8 + 1 |
 | Mokerlink| 2G040210GSM     | Yes     | [2M-PCB43-V1.1](devices/2M-PCB43-V1.1.md)                                 |       | 4 + 2 |
 | Mokerlink| ZX-SWTGW218AS   | Yes     | [SWTG118AS-V2.0-16029](devices/SWTGW218AS.md)                             | 2M    | 8 + 1 |
 | MokerLink| POE-2G080110GS  | No      | [2M-PCB51-ML-V1.1](devices/2M-PCB51-ML-V1_1.md)                           | 4M    | 8 + 1 |
+| Binardat | 2G06-04210GSM    | No      | [PCB-SWTG024AS-A-2.0.1](devices/ONT-S207CW-62TS-SE.md)                 | 0.5M  | 4 + 2 |
+| ONT      | ONT-S207CW-62TS-SE | No   | [PCB-SWTG024AS-A-2.0.1](devices/ONT-S207CW-62TS-SE.md)                 | 0.5M  | 4 + 2 |
 | Netcore  | GS9             | No      | [PB-2132](devices/PB-2132.md)                                             | 4M    | 8 + 1 |
 | Ruiying  | RY-4GT-2SX      | No      | [FG-4GT-2SX_V2.0](devices/FG-4GT-2SX_V2.0.md)                             | 4M    | 4 + 2 |
 | Ruiying  | RY-8GT-1SX      | No      | [FG-8GT-1SX](devices/FG-8GT-1SX.md)                                       | 1M    | 8 + 1 |
@@ -36,6 +41,7 @@ The following devices have been tested and are fully working:
 | Xikestore| SKS3200M-4GPY2XF| Yes     | [SWTG024AS-v1.0](devices/SWTG024AS.md)                                    |       | 4 + 2 |
 | XikeStor | SKS3200-8E1X    | Yes     | [SWTG118AS-V2.1-17462](devices/SWTGW218AS.md)                             | 2M    | 8 + 1 |
 | Ztyuav   | Z-QWYT0402      | No      | [PCB-K0402WS-V3.0](devices/PCB-K0402WS-V3.0.md)                           |       | 4 + 2 |
+| Guangnianwei | 7018-2.5G   | No      | [F7008-2.5GPOE-V1.2](devices/F7008-2.5.md)                                | 8M    | 8 + 1 |
 
 For KP-9000-6XH-X2 / KP-9000-6XHML-X2 / Mokerlink 2G040210GSM devices, select
 the machine target by PCB revision. The ML/non-ML or managed/unmanaged label

html/index.html

@@ -331,8 +331,36 @@ button.danger{background:var(--bad);color:#fff;border-color:transparent}
       </div>
     </section>
 
+    <section class="tab" id="tab-lldp">
+      <div class="card"><h2 data-i18n="lldp_title">LLDP</h2>
+        <label class="row"><span class="lb" data-i18n="lldp_enabled">Enabled</span>
+          <span class="switch"><input type="checkbox" id="lldp_en"><i></i></span>
+        </label>
+        <div class="scrollx"><table class="t" id="lldp_table">
+          <thead><tr><th data-i18n="c_port">Port Number</th><th data-i18n="lldp_portname">Name</th><th data-i18n="lldp_enable">Send Frames</th></tr></thead>
+          <tbody></tbody></table></div>
+      </div>
+    </section>
+
+    <section class="tab" id="tab-isolate">
+      <div class="card"><h2 data-i18n="iso_title">Port isolation</h2>
+        <p class="small mut" style="margin-bottom:10px" data-i18n="iso_intro">A frame entering a port may only leave through the ports ticked in its row.</p>
+        <div class="scrollx"><table class="t" id="isotbl" style="width:auto"><thead></thead><tbody></tbody></table></div>
+        <p class="small mut" style="margin-top:6px" data-i18n="iso_legend">The cell of the port itself is always allowed.</p>
+        <div style="display:flex;gap:12px;margin-top:10px">
+          <button class="ctl pri" id="isoapply" data-i18n="c_apply">Apply</button>
+          <button class="ctl" id="isoall" data-i18n="iso_all">Allow all</button>
+        </div>
+      </div>
+    </section>
+
     <section class="tab" id="tab-lag">
       <div id="lagwrap" class="grid2"></div>
+      <div class="card" style="margin-top:14px"><h2 data-i18n="lacp_heading">LACP (802.3ad)</h2>
+        <div class="scrollx"><table class="t" id="lacptbl">
+          <thead><tr><th data-i18n="c_port">Port</th><th>LAG</th><th data-i18n="lacp_actor">Actor</th><th data-i18n="lacp_partner">Partner</th><th data-i18n="lacp_rxstate">RX state</th><th data-i18n="lacp_rx">LACPDUs received</th><th data-i18n="lacp_psys">Partner system</th></tr></thead>
+          <tbody></tbody></table></div>
+      </div>
       <p class="small mut" style="margin-top:10px" data-i18n="lag_note">A LAG needs at least one member to be saved in the startup config; applying an empty group clears it.</p>
     </section>
 
@@ -351,6 +379,12 @@ button.danger{background:var(--bad);color:#fff;border-color:transparent}
           <thead><tr><th data-i18n="c_port">Port</th><th data-i18n="bw_in">Ingress limit</th><th>Mbit/s</th><th data-i18n="bw_exceed">When exceeded</th><th data-i18n="bw_out">Egress limit</th><th>Mbit/s</th><th></th></tr></thead>
           <tbody></tbody></table></div>
       </div>
+      <div class="card"><h2><span data-i18n="sc_title">Storm control</span> <span class="hint" data-i18n="sc_h">per port and traffic type, empty = off</span></h2>
+        <div class="scrollx"><table class="t" id="sctable">
+          <thead><tr><th data-i18n="c_port">Port</th><th data-i18n="sc_bcast">Broadcast</th><th data-i18n="sc_mcast">Multicast</th><th data-i18n="sc_ucast">Unknown unicast</th><th data-i18n="sc_umcast">Unknown multicast</th><th></th></tr></thead>
+          <tbody></tbody></table></div>
+        <p class="small mut" style="margin-top:8px" data-i18n="sc_note">Frames of a type above its limit are dropped where they enter the switch.</p>
+      </div>
     </section>
 
     <section class="tab" id="tab-system">
@@ -360,6 +394,9 @@ button.danger{background:var(--bad);color:#fff;border-color:transparent}
           <label class="row"><span class="lb" data-i18n="i_ip">IP address</span><input class="in" id="sy-ip" size="15"></label>
           <label class="row"><span class="lb" data-i18n="i_mask">Netmask</span><input class="in" id="sy-mask" size="15"></label>
           <label class="row"><span class="lb" data-i18n="i_gw">Gateway</span><input class="in" id="sy-gw" size="15"></label>
+          <label class="row"><span class="lb" data-i18n="sy_dns1">DNS server</span><input class="in" id="sy-dns1" size="15"></label>
+          <label class="row"><span class="lb" data-i18n="sy_dns2">Second DNS</span><input class="in" id="sy-dns2" size="15"></label>
+          <p class="small mut" id="sy-dnsdhcp"></p>
           <div style="display:flex;gap:10px;margin-top:12px">
             <button class="ctl pri" id="sy-apply" data-i18n="c_apply">Apply</button>
             <button class="ctl" id="sy-dhcp" data-i18n="sy_dhcp" data-i18n-t="sy_dhcp_t">Use DHCP</button>
@@ -375,8 +412,26 @@ button.danger{background:var(--bad);color:#fff;border-color:transparent}
             <input class="in" id="sy-sysip" style="flex:1;min-width:0;width:0" data-i18n-p="sy_sysip">
             <span class="small mut" data-i18n="sy_port">Port</span>
             <input class="in" id="sy-sysport" style="width:64px" type="number" min="1" max="65535"></div>
+          <label class="row" style="justify-content:space-between"><span data-i18n="sy_sesstmo">Session timeout (s)</span>
+            <input class="in" id="sy-sesstmo" style="width:80px" type="number" min="1" max="65535"></label>
           <p class="small mut" data-i18n="sy_services_note">Service state reflects the startup config; runtime state is not readable.</p>
         </div>
+        <div class="card" id="sy-ntpcard"><h2 data-i18n="sy_time">Time</h2>
+          <label class="row" style="justify-content:space-between"><span data-i18n="sy_ntp">NTP</span>
+            <span class="switch"><input type="checkbox" id="sy-ntp"><i></i></span></label>
+          <label class="row"><span class="lb" data-i18n="sy_ntpsrv">NTP server</span><input class="in" id="sy-ntpsrv" maxlength="47" data-i18n-p="sy_ntpsrv_p"></label>
+          <label class="row"><span class="lb" data-i18n="sy_ntpint">Poll interval [min]</span><input class="in sm" id="sy-ntpint" type="number" min="1" max="1440"></label>
+          <label class="row"><span class="lb" data-i18n="sy_tz">Time zone</span><select class="in" id="sy-tz"></select></label>
+          <label class="row"><span class="lb" data-i18n="sy_dst">Daylight saving</span><select class="in" id="sy-dst"><option value="off" data-i18n="c_offc">Off</option><option value="eu" data-i18n="sy_dst_eu">Europe</option><option value="us" data-i18n="sy_dst_us">United States</option></select></label>
+          <div style="display:flex;gap:10px;margin-top:8px">
+            <button class="ctl pri" id="sy-ntpapply" data-i18n="c_apply">Apply</button>
+            <button class="ctl" id="sy-ntprefresh" data-i18n="c_refresh">Refresh</button>
+          </div>
+          <label class="row" style="margin-top:10px"><span class="lb" data-i18n="sy_now">Local time</span><span class="mono" id="sy-now">-</span></label>
+          <label class="row"><span class="lb" data-i18n="sy_sync">Last synchronisation</span><span id="sy-sync">-</span></label>
+          <label class="row"><span class="lb" data-i18n="sy_ntpaddr">Server address</span><span class="mono" id="sy-ntpaddr">-</span></label>
+          <p class="small mut" style="margin-top:8px" data-i18n="sy_time_note">The switch has no battery backed clock.</p>
+        </div>
         <div class="card"><h2 data-i18n="sy_password">Admin password</h2>
           <label class="row"><span class="lb" data-i18n="sy_newpw">New password</span><input class="in" id="sy-pw1" type="password" maxlength="20"></label>
           <label class="row"><span class="lb" data-i18n="sy_repeat">Repeat</span><input class="in" id="sy-pw2" type="password" maxlength="20"></label>
@@ -393,9 +448,13 @@ button.danger{background:var(--bad);color:#fff;border-color:transparent}
         <div class="card"><h2 data-i18n="sy_display">Display</h2>
           <label class="row"><span class="lb" data-i18n="sy_lang">Language</span>
             <select class="in" id="langSel">
+              <option value="de">Deutsch</option>
               <option value="en">English</option>
+              <option value="es">Español</option>
+              <option value="fr">Français</option>
               <option value="ja">日本語</option>
               <option value="zh">中文</option>
+              
             </select></label>
           <label class="row"><span class="lb" data-i18n="sy_theme">Theme</span>
             <select class="in" id="themeSel">

html/login.html

@@ -81,16 +81,23 @@ button:hover{filter:brightness(1.1)}
 <script>
 (function(){
   var L={
+    de:["Switch-Anmeldung","RTLPlayground-Verwaltungsoberfläche","Passwort","Anmelden","Falsches Passwort, bitte erneut versuchen."],
     en:["Switch Login","RTLPlayground management interface","Password","Sign in","Wrong password, try again."],
     ja:["スイッチ ログイン","RTLPlayground 管理インターフェース","パスワード","ログイン","パスワードが違います。もう一度お試しください。"],
-    zh:["交换机登录","RTLPlayground 管理界面","密码","登录","密码错误，请重试。"]
+    zh:["交换机登录","RTLPlayground 管理界面","密码","登录","密码错误，请重试。"],
+    es:["Inicio de sesión del switch","Interfaz de gestión de RTLPlayground","Contraseña","Iniciar sesión","Contraseña incorrecta, inténtalo de nuevo."],
+    fr:["Utilisateur du commutateur","Interface de management RTLPlayground","Mot de passe","Se connecter","Mot de passe erronné, essayez à nouveau."]
   };
   var l=null;
   try{l=localStorage.getItem("rtl_lang");}catch(e){}
   if(!L[l])l=(navigator.language||"en").slice(0,2);
   var s=L[l]||L.en;
-  document.title=s[0];
-  document.getElementById("hn").textContent=s[0];
+  // Name the tab after the switch: the hostname seen at the last login here,
+  // otherwise the address, so several open switches can be told apart
+  var host=null;
+  try{host=localStorage.getItem("rtl_host");}catch(e){}
+  document.title=(host||location.hostname)+" – "+s[0];
+  document.getElementById("hn").textContent=host||s[0];
   document.getElementById("sub").textContent=s[1];
   document.getElementById("lp").textContent=s[2];
   document.getElementById("lb").textContent=s[3];

httpd/httpd.c

@@ -12,7 +12,11 @@
 #include "debug.h"
 
 #define SESSION_ID_LENGTH 12
-#define SESSION_TIMEOUT 200
+#define SESSION_TIMEOUT_DEFAULT 200
+
+/* Seconds of inactivity after which a session cookie stops validating.
+ * Configurable with the "session" command, see cmd_parser.c. */
+__xdata uint16_t session_timeout = SESSION_TIMEOUT_DEFAULT;
 
 #define CMARK_S 6
 
@@ -22,9 +26,9 @@
 extern volatile __xdata uint8_t sfr_data[4];
 extern volatile __xdata uint32_t ticks;
 extern __xdata uint8_t cmd_capture;	/* owned by rtlplayground.c, see write_char_no_syslog() */
-extern __code uint8_t * __code hex;
-extern __code struct f_data f_data[];
-extern __code char * __code mime_strings[];
+extern __code const uint8_t * __code const hex;
+extern __code const struct f_data f_data[];
+extern __code const char * __code const mime_strings[];
 extern __xdata struct flash_region_t flash_region;
 extern __xdata uint32_t flash_size;
 
@@ -127,7 +131,7 @@ uint8_t find_entry(__xdata uint8_t *e)
 }
 
 
-bool is_word(__xdata uint8_t *xdata_str_p, __code uint8_t * __xdata code_str_p)
+bool is_word(__xdata uint8_t *xdata_str_p, __code const uint8_t * __xdata code_str_p)
 {
 	uint8_t u, c;
 
@@ -149,7 +153,7 @@ bool is_word(__xdata uint8_t *xdata_str_p, __code uint8_t * __xdata code_str_p)
 
 
 /* name must be lower-case, starting with the '\n' of the previous line's end */
-__xdata uint8_t *header_value(__xdata uint8_t *p, __code uint8_t *name)
+__xdata uint8_t *header_value(__xdata uint8_t *p, __code const uint8_t *name)
 {
 	uint8_t u, c;
 
@@ -342,7 +346,7 @@ __xdata uint8_t *scan_header(__xdata uint8_t * __xdata p)
 	read_reg_timer(&now);
 
 	if (session && session_id[0]) {
-		if (now - last_session_use > SESSION_TIMEOUT) {
+		if (now - last_session_use > session_timeout) {
 			dbg_string("Session expired\n");
 		} else {
 			if (is_word_x(session, session_id)) {
@@ -377,8 +381,8 @@ void gen_random_hex_chars(__xdata uint8_t * b, __xdata uint8_t bytes)
 static uint8_t config_take(void)
 {
 	// #386: needs static, otherwise it still lands in SRAM/DSEG
-	static __xdata uint16_t cfg_pos, cfg_hdr, cfg_body, cfg_end, cfg_last;
-	__xdata uint8_t cfg_bl;
+	static __xdata uint16_t cfg_pos, cfg_hdr, cfg_body, cfg_end, cfg_last, cfg_i;
+	__xdata uint8_t cfg_bl, cfg_run;
 
 	cfg_bl = strlen_x(boundary);
 
@@ -420,6 +424,13 @@ static uint8_t config_take(void)
 				// the payload plus its terminator must fit the sector
 				if (cfg_end - cfg_body + 1 > CONFIG_LEN)
 					return 2;
+				cfg_run = 0;
+				for (cfg_i = cfg_body; cfg_i < cfg_end; cfg_i++) {
+					if (config_buf[cfg_i] == '\n')
+						cfg_run = 0;
+					else if (++cfg_run >= CMD_BUF_SIZE - 1)
+						return 2;
+				}
 				config_buf[cfg_end] = 0;
 				flash_region.addr = CONFIG_START;
 				flash_sector_erase();
@@ -532,6 +543,19 @@ uint8_t stream_upload(void)
 			crc16_bank1(upload_settings.p + upload_settings.bptr);
 			flash_buf[write_len++] = upload_settings.p[upload_settings.bptr++];
 			if (write_len >= FLASH_PAGE_SIZE) {
+				/* The staged image spans FIRMWARE_UPLOAD_START to twice that,
+				 * the span check_and_flash_update_image() reads back. Nothing
+				 * else bounds uptr: a body whose closing boundary never arrives
+				 * keeps writing, and on a flash exactly this size the address
+				 * wraps onto the running image at zero. */
+				if (uptr >= (uint32_t)FIRMWARE_UPLOAD_START * 2) {
+					print_string("Upload runs past the image area! Aborting.\n");
+					slen = strtox(outbuf, "HTTP/1.1 400 Bad Request\r\nContent-Length: 30\r\n"
+						"Content-Type: text/plain\r\n\r\n"
+						"NO: upload exceeds image area\n");
+					s->tstate = TSTATE_NONE;
+					return 0;
+				}
 				dbg_string("len: "); dbg_short(write_len); dbg_char(' ');
 				dbg_string("CRC16: "); dbg_short(crc_value); dbg_char('\n');
 				if (uptr % FLASH_SECTOR_SIZE == 0) {
@@ -752,6 +776,10 @@ void handle_post(void)
 			return;
 		}
 		if (is_word(request_path, "upload")) {
+			if (!authenticated) {
+				send_unauthorized();
+				return;
+			}
 			if (flash_size < FIRMWARE_UPLOAD_START*2)
 			{
 				print_string("Flash too small for firmware upload!\n");
@@ -779,7 +807,23 @@ void handle_post(void)
 		dbg_string("Multipart request\n");
 	}
 
-	if (is_word(request_path, "cmd")) {
+	if (s->tstate == TSTATE_MULTIPART || is_word(request_path, "upload") || is_word(request_path, "config")) {
+		dbg_string("POST upload/config request\n");
+		if (!authenticated) {
+			send_unauthorized();
+			return;
+		}
+		if (!boundary[0]) {
+			dbg_string("Bad request, no boundary!\n");
+			send_bad_request();
+			return;
+		}
+		if (config_upload)
+			handle_config_fragment(p);
+		else
+			handle_firmware_fragment(p);
+		return;
+	} else if (is_word(request_path, "cmd")) {
 		p += 4;
 		if (!authenticated) {
 			send_unauthorized();
@@ -805,22 +849,6 @@ void handle_post(void)
 			return;
 		run_login_body(p);
 		return;
-	} else if (s->tstate == TSTATE_MULTIPART || is_word(request_path, "upload") || is_word(request_path, "config")) {
-		dbg_string("POST upload/config request\n");
-		if (!authenticated) {
-			send_unauthorized();
-			return;
-		}
-		if (!boundary[0]) {
-			dbg_string("Bad request, no boundary!\n");
-			send_bad_request();
-			return;
-		}
-		if (config_upload)
-			handle_config_fragment(p);
-		else
-			handle_firmware_fragment(p);
-		return;
 	} else {
 		send_not_found();
 		return;
@@ -907,8 +935,9 @@ void httpd_appcall(void)
 			reset_chip();
 		}
 	} else if (uip_newdata() && s->tstate == TSTATE_POST) {
-		// Check here maxupload by subtracting uip_len and close socekt if fails!
-		if (max_upload - uip_len > 0) {
+		if (config_upload || uip_len <= max_upload) {
+			if (!config_upload)
+				max_upload -= uip_len;
 			upload_settings.p = uip_appdata;
 			upload_settings.bptr = 0;
 			upload_settings.plen = uip_len;
@@ -987,6 +1016,8 @@ void httpd_appcall(void)
 				send_eee();
 			} else if (is_word(q, "/bandwidth.json")) {
 				send_bandwidth();
+			} else if (is_word(q, "/storm.json")) {
+				send_storm();
 			} else if (is_word(q, "/l2.json")) {
 				parse_short(q + 13); // e.g.: /l2.json?idx=10
 				send_l2(short_parsed);
@@ -995,12 +1026,18 @@ void httpd_appcall(void)
 				l2_delete(short_parsed);
 			} else if (is_word(q, "/mirror.json")) {
 				send_mirror();
+			} else if (is_word(q, "/isolation.json")) {
+				send_isolation();
 			} else if (is_word(q, "/mtu.json")) {
 				send_mtu();
 			} else if (is_word(q, "/lag.json")) {
 				send_lag();
 			} else if (is_word(q, "/stp.json")) {
 				send_stp();
+			} else if (is_word(q, "/lldp.json")) {
+				send_lldp();
+			} else if (is_word(q, "/lacp.json")) {
+				send_lacp();
 			} else if (is_word(q, "/vlanlist")) {
 				send_vlanlist();
 			} else if (is_word(q, "/config")) {

httpd/page_impl.c

@@ -3,6 +3,7 @@
 #include "rtl837x_sfr.h"
 #include "rtl837x_common.h"
 #include "rtl837x_regs.h"
+#include "rtl837x_storm.h"
 #include "rtl837x_port.h"
 #include "rtl837x_flash.h"
 #include "rtl837x_pins.h"
@@ -13,6 +14,7 @@
 #include "version.h"
 #include "machine.h"
 #include "rtl837x_stp.h"
+#include "rtl837x_lacp.h"
 #include "page_impl.h"
 #include "syslog.h"
 
@@ -28,9 +30,10 @@ extern __code const struct machine machine;
 extern __xdata uint8_t outbuf[TCP_OUTBUF_SIZE];
 extern __xdata uint16_t slen;
 extern __xdata uint16_t management_vlan;
+extern __xdata uint16_t session_timeout;
 extern __xdata uint16_t cont_len;
 extern __xdata uint32_t cont_addr;
-extern __code uint8_t * __code hex;
+extern __code const uint8_t * __code const hex;
 extern __xdata uip_ipaddr_t uip_hostaddr, uip_draddr, uip_netmask;
 
 extern __xdata uint8_t sfr_data[4];
@@ -47,8 +50,11 @@ extern __xdata char sfp_module_model[2][17];
 extern __xdata char sfp_module_serial[2][17];
 extern __xdata uint8_t sfp_options[2];
 
-__code uint8_t * __code HTTP_RESPONCE_JSON = "HTTP/1.1 200 OK\r\nConnection: close\r\nContent-Type: application/json\r\n\r\n";
-__code uint8_t * __code HTTP_RESPONCE_TXT = "HTTP/1.1 200 OK\r\nConnection: close\r\nContent-Type: text/plain\r\n\r\n";
+extern __xdata uint16_t lldp_logical_port_status;
+extern __xdata bool lldp_enabled;
+
+__code const uint8_t * __code const HTTP_RESPONCE_JSON = "HTTP/1.1 200 OK\r\nConnection: close\r\nContent-Type: application/json\r\n\r\n";
+__code const uint8_t * __code const HTTP_RESPONCE_TXT = "HTTP/1.1 200 OK\r\nConnection: close\r\nContent-Type: text/plain\r\n\r\n";
 
 // Convert uint8_t to ascii HEX char push on html-buffer.
 void charhex_to_html(char c)
@@ -114,12 +120,14 @@ void itoa_html(uint8_t v)
 	char_to_html('0' + (v % 10));
 }
 
-void itoa16_html(uint16_t v) /* sufficient for VLAN IDs (max 4094) */
+void itoa16_html(uint16_t v) /* up to five digits (65535) */
 {
 	uint8_t print_zeros = 0;
 	uint8_t d;
-	d = v / 1000;
+	d = v / 10000;
 	if (d) { char_to_html('0' + d); print_zeros = 1; }
+	d = (v / 1000) % 10;
+	if (d || print_zeros) { char_to_html('0' + d); print_zeros = 1; }
 	d = (v / 100) % 10;
 	if (d || print_zeros) { char_to_html('0' + d); print_zeros = 1; }
 	d = (v / 10) % 10;
@@ -127,11 +135,28 @@ void itoa16_html(uint16_t v) /* sufficient for VLAN IDs (max 4094) */
 	char_to_html('0' + (v % 10));
 }
 
-void string_to_html(__code char *s)
+void string_to_html(__code const char *s)
 {
 	while (*s) char_to_html(*s++);
 }
 
+static void temp_to_html(void)
+{
+	int16_t v;
+
+	reg_read(RTL837X_TM_RESULT);
+	v = SFR_DATA_U16;
+	if (v < 0) {
+		char_to_html('-');
+		v = -v;
+	}
+	itoa_html(v >> 7);
+	char_to_html('.');
+	itoa_html(((v & 0x7f) * 10) >> 7);
+	char_to_html(' ');
+	char_to_html('C');
+}
+
 uint16_t stat_content(void)
 {
 	dbg_string("stat_content called\n");
@@ -258,7 +283,9 @@ void send_basic_info(void)
 	itoa_html(syslog_state.server_ip[2]); char_to_html('.');
 	itoa_html(syslog_state.server_ip[3]); char_to_html(':');
 	itoa16_html(syslog_state.server_port);
-	slen += strtox(outbuf + slen, "\",\"mac_address\":\"");
+	slen += strtox(outbuf + slen, "\",\"session_timeout\":");
+	itoa16_html(session_timeout);
+	slen += strtox(outbuf + slen, ",\"mac_address\":\"");
 	byte_to_html(uip_ethaddr.addr[0]); char_to_html(':');
 	byte_to_html(uip_ethaddr.addr[1]); char_to_html(':');
 	byte_to_html(uip_ethaddr.addr[2]); char_to_html(':');
@@ -277,6 +304,8 @@ void send_basic_info(void)
 	slen += strtox(outbuf + slen, BUILD_DATE);
 	slen += strtox(outbuf + slen, "\",\"hw_ver\":\"");
 	slen += strtox(outbuf + slen, machine.machine_name);
+	slen += strtox(outbuf + slen, "\",\"chip_temp\":\"");
+	temp_to_html();
 	slen += strtox(outbuf + slen, "\",\"flash_size\":\"");
 	string_to_html(get_flash_size_str());
 
@@ -594,7 +623,6 @@ static void bridge_to_html(void)
 		byte_to_html(pi_mac[i]);
 }
 
-
 void send_stp(void)
 {
 	uint8_t i, j, st, dsg;
@@ -709,8 +737,84 @@ void send_stp(void)
 	slen += strtox(outbuf + slen, "]}");
 }
 
+void send_lacp(void)
+{
+	dbg_string("send_lacp called\n");
+	slen = strtox(outbuf, HTTP_RESPONCE_JSON);
 
+	slen += strtox(outbuf + slen, "{\"on\":");
+	bool_to_html(lacpEnabled);
+	slen += strtox(outbuf + slen, ",\"lags\":[");
+	for (uint8_t l = 0; l < LACP_NUM_LAGS; l++) {
+		slen += strtox(outbuf + slen, "{\"cfg\":\"");
+		byte_to_html(lacp_lag_ports[l] >> 8);
+		byte_to_html(lacp_lag_ports[l]);
+		slen += strtox(outbuf + slen, "\",\"aggValid\":");
+		bool_to_html(lacp_agg_valid[l]);
+		slen += strtox(outbuf + slen, ",\"agg\":\"");
+		for (uint8_t j = 0; j < MAC_ADDR_LEN; j++)
+			byte_to_html(lacp_agg_sys[l][j]);
+		slen += strtox(outbuf + slen, "\",\"members\":\"");
+		byte_to_html(lacp_members_last[l] >> 8);
+		byte_to_html(lacp_members_last[l]);
+		slen += strtox(outbuf + slen, "\"},");
+	}
+	slen -= 1; // remove comma
+	slen += strtox(outbuf + slen, "],\"ports\":[");
+	for (uint8_t i = machine.min_port; i <= machine.max_port; i++) {
+		slen += strtox(outbuf + slen, "{\"p\":");
+		itoa_html(machine.log_to_phys_port[i]);
+		slen += strtox(outbuf + slen, ",\"lag\":");
+		itoa_html(lacp_port_lag[i]);
+		slen += strtox(outbuf + slen, ",\"a\":\"");
+		byte_to_html(lacp_actor_state[i]);
+		slen += strtox(outbuf + slen, "\",\"pt\":\"");
+		byte_to_html(lacp_partner_state[i]);
+		slen += strtox(outbuf + slen, "\",\"rs\":");
+		itoa_html(lacp_rx_state[i]);
+		slen += strtox(outbuf + slen, ",\"rx\":\"");
+		byte_to_html(lacp_rx_count[i] >> 8);
+		byte_to_html(lacp_rx_count[i]);
+		slen += strtox(outbuf + slen, "\",\"psys\":\"");
+		for (uint8_t j = 0; j < MAC_ADDR_LEN; j++)
+			byte_to_html(lacp_partner_sys[i][j]);
+		slen += strtox(outbuf + slen, "\"},");
+	}
+	slen -= 1; // remove comma
+	slen += strtox(outbuf + slen, "]}");
+}
 
+void send_lldp(void)
+{
+	dbg_string("send_lldp called\n");
+	slen = strtox(outbuf, HTTP_RESPONCE_JSON);
+
+	slen += strtox(outbuf + slen, "{\"on\":");
+	bool_to_html(lldp_enabled);
+	slen += strtox(outbuf + slen, ",\"portStatus\":[");
+
+	for (uint8_t i = machine.min_port; i <= machine.max_port; i++) {
+		slen += strtox(outbuf + slen, "{\"portNum\":");
+		itoa_html(machine.log_to_phys_port[i]);
+
+		slen += strtox(outbuf + slen, ",\"logPort\":");
+		itoa_html(i);
+		slen += strtox(outbuf + slen, ",\"name\":\"");
+		for (uint8_t j = 0; j < PORT_NAME_SIZE && port_names[i][j]; j++) {
+			json_char_to_html(port_names[i][j]);
+		}
+
+		slen += strtox(outbuf + slen, "\",\"permitted\":");
+		bool_to_html(1 & (lldp_logical_port_status >> i));
+		slen += strtox(outbuf + slen, "}");
+
+		if (i < machine.max_port)
+			char_to_html(',');
+		else
+			char_to_html(']');
+	}
+	char_to_html('}');
+}
 
 void send_eee(void)
 {
@@ -804,6 +908,63 @@ void send_bandwidth(void)
 }
 
 
+void send_storm(void)
+{
+	__xdata uint8_t i, t, idx;
+
+	slen = strtox(outbuf, HTTP_RESPONCE_JSON);
+	char_to_html('[');
+	for (i = machine.min_port; i <= machine.max_port; i++) {
+		slen += strtox(outbuf + slen, "{\"portNum\":");
+		itoa_html(machine.log_to_phys_port[i]);
+		slen += strtox(outbuf + slen, ",\"en\":\"");
+		for (t = 0; t < STORM_TYPES; t++)
+			char_to_html(reg_bit_test(RTL837X_STORM_CTRL + (t << 2), i) ? '1' : '0');
+		slen += strtox(outbuf + slen, "\",\"pps\":\"");
+		for (t = 0; t < STORM_TYPES; t++) {
+			idx = STORM_METER(i, t);
+			char_to_html(reg_bit_test(RTL837X_METER_MODE + ((idx >> 5) << 2), idx & 0x1f) ? '1' : '0');
+		}
+		slen += strtox(outbuf + slen, "\",\"rate\":\"");
+		for (t = 0; t < STORM_TYPES; t++) {
+			reg_read_m(RTL837X_METER_RATE + (STORM_METER(i, t) << 2));
+			byte_to_html(sfr_data[1]);
+			byte_to_html(sfr_data[2]);
+			byte_to_html(sfr_data[3]);
+		}
+		char_to_html('"');
+		char_to_html('}');
+		if (i < machine.max_port)
+			char_to_html(',');
+		else
+			char_to_html(']');
+	}
+}
+
+
+void send_isolation(void)
+{
+	__xdata uint16_t allow;
+
+	dbg_string("send_isolation called\n");
+	slen = strtox(outbuf, HTTP_RESPONCE_JSON);
+	char_to_html('[');
+	for (uint8_t i = machine.min_port; i <= machine.max_port; i++) {
+		slen += strtox(outbuf + slen, "{\"portNum\":");
+		itoa_html(machine.log_to_phys_port[i]);
+		slen += strtox(outbuf + slen, ",\"allow\":\"");
+		allow = port_isolation_get(i);
+		byte_to_html(allow >> 8);
+		byte_to_html(allow & 0xff);
+		char_to_html('"');
+		char_to_html('}');
+		if (i < machine.max_port)
+			char_to_html(',');
+	}
+	char_to_html(']');
+}
+
+
 void send_mtu(void)
 {
 	dbg_string("send_mtu called\n");
@@ -1011,7 +1172,7 @@ void send_cmd_log(void)
 	__xdata uint8_t found_begin = 0;
 	dbg_string("History ptr: ");
 	dbg_short(cmd_history_ptr); dbg_char('\n');
-	while (p != cmd_history_ptr) {
+	while (p != cmd_history_ptr && slen < TCP_OUTBUF_SIZE) {
 		if (!cmd_history[p] || cmd_history[p] == '\n')
 			found_begin = 1;
 		if (found_begin && cmd_history[p])
@@ -1036,8 +1197,7 @@ void send_vlanlist(void)
 	slen += strtox(outbuf + slen, ",\"vlan\":[");
 
 	for (i = 1; i < 4095; i++) {
-		if (vlan_get(i) < 0)
-			continue;
+		vlan_get(i);
 		if (!(sfr_data[0] & 0x02)) /* bit 1: VLAN table entry valid */
 			continue;
 

httpd/page_impl.h

@@ -3,22 +3,28 @@
 
 #include <stdbool.h>
 
-extern __code uint8_t * __code HTTP_RESPONCE_TXT;
+extern __code const uint8_t * __code const HTTP_RESPONCE_TXT;
+
+void itoa16_html(uint16_t v);
 
 bool send_counters(uint8_t phys_port);
 void send_status(void);
 void send_vlan(uint16_t vlan);
 void send_basic_info(void);
 void send_bandwidth(void);
+void send_storm(void);
 void send_eee(void);
 void send_l2(uint16_t idx);
 void l2_delete(uint16_t idx);
 void send_mirror(void);
 void send_mtu(void);
+void send_isolation(void);
 void send_config(void);
 void send_cmd_log(void);
 void send_lag(void);
 void send_stp(void);
+void send_lldp(void);
+void send_lacp(void);
 void send_vlanlist(void);
 
 /*  Convert only the lower nibble to ascii HEX char.

installer/installer.c

@@ -30,7 +30,7 @@
 __xdata uint8_t buffer[0x1000];
 __xdata uint8_t dio_enabled;
 
-__code uint8_t * __code hex = "0123456789abcdef";
+__code const uint8_t * __code const hex = "0123456789abcdef";
 
 void isr_timer0(void) __interrupt(1)
 {
@@ -67,7 +67,7 @@ void write_char(char c)
 }
 
 
-void print_string(__code char *p)
+void print_string(__code const char *p)
 {
 	while (*p)
 		write_char(*p++);

machine.h

@@ -3,58 +3,19 @@
 
 #include <stdint.h>
 
-/*
- * Select your machine type below
- */
-// Legacy KP-9000 4+2 targets. Prefer the PCB-revision-specific targets below.
-// #define MACHINE_KP_9000_6XHML_X2
-// #define MACHINE_KP_9000_6XH_X2
+#define MACHINE_STR_HELPER(x)  #x
+#define MACHINE_STR(x) MACHINE_STR_HELPER(x)
 
-// KP-9000 4+2 targets by PCB silkscreen revision.
-// #define MACHINE_KP_9000_6XH_X2_V1_1
-// #define MACHINE_KP_9000_6XHML_X2_V1_1
-// #define MACHINE_KP_9000_6XH_X2_V1_2
-// #define MACHINE_KP_9000_6XHML_X2_V1_2
-// #define MACHINE_KP_9000_6XH_X2_V2_1
-// #define MACHINE_KP_9000_6XHML_X2_V2_1
 
-// #define MACHINE_KP_9000_6XH_X
-// #define MACHINE_KP_9000_9XH_X_EU
-// #define MACHINE_KP_9000_9XHML_X_V2_2
-// #define MACHINE_KP_9000_9XHML_X_V3_1
-// #define MACHINE_SWGT024_V2_0_MANAGED
-// #define MACHINE_SWGT024_V2_0_UNMANAGED
-// #define MACHINE_TRENDNET_TEG_S562
-// #define MACHINE_HG0402XG_V1_1
-// #define MACHINE_SWTG018AS_A_V_2_0
-// #define MACHINE_SWTGW218AS
-// #define MACHINE_PCB_SWTG018AS_V2_1_0
-// #define MACHINE_PCB_K0402WS_V3
-// #define MACHINE_PCB_K0402WS_V2
-// #define MACHINE_K0501W_V2_0
-// #define MACHINE_LIANGUO_ZX_SWTGW215AS
-// #define MACHINE_ZX310S_4T2XH
-// #define MACHINE_ZX310S_4T2XT
-// #define MACHINE_STEAMEMO_IG204_V1
-// #define MACHINE_DEFAULT_8C_1SFP
-// #define MACHINE_HI_K0801WS
-// #define MACHINE_FNS1200P
-// #define MACHINE_PCB_SWTG024AS_A_2_0_1
-// #define MACHINE_SWTG024AS_A_2_0_1_5C_1SFP
-// #define MACHINE_SWTG024AS_V2_0
-// #define MACHINE_FG_4GT_2SX_V2_0
-// #define MACHINE_FG_8GT_1SX
-// #define MACHINE_LIANGUO_HYWS_SGT0108S
-// #define MACHINE_POE_2G080110GS
-// #define MACHINE_PB_2132
-// #define MACHINE_HASIVO_S600W_4GT_2XGT_SE
+#define MACHINE_DEF_DIR machine
 
-typedef struct {
-	// GPIO pins for SDA/SCL
-	uint8_t sda; 
-	uint8_t scl;
-} i2c_bus_t;
+#ifndef MACHINE_NAME
+	#define MACHINE_NAME default_machine
+#endif
 
+#define MACHINE_INC(dir,file) MACHINE_STR(dir/file)
+
+#include  MACHINE_INC(MACHINE_DEF_DIR,MACHINE_NAME.h)
 
 #define LED_27 1
 // SYSTEM LED
@@ -74,7 +35,7 @@ struct sfp_port
 	uint8_t pin_los; // gpio number 0-63, 0xFF = don't have it?
 	uint8_t pin_tx_disable; // gpio number 0-63, 0xFF = not present
 	uint8_t sds;
-	i2c_bus_t i2c;
+	uint8_t i2c;
 };
 
 struct machine {

machine/DEFAULT_8C_1SFP.c

@@ -0,0 +1,25 @@
+#include "machine_defs.h"
+
+__code const struct machine machine = {
+	.machine_name = MACHINE_MODEL,
+	.isRTL8373 = 1,
+	.min_port = 0,
+	.max_port = 8,
+	.n_sfp = 1,
+	.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
+	.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
+	.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
+	.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
+	.sfp_port[0].pin_los = GPIO37,
+	.sfp_port[0].pin_tx_disable = GPIO_NA,
+	.sfp_port[0].sds = 1,
+	.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
+	.reset_pin = GPIO_NA,
+	.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28_SYS | LED_29 },
+	.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 0},
+	.led_sets = { { LEDS_2G5 | LEDS_TWO_PAIR_1G | LEDS_1G | LEDS_500M | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G | LEDS_TWO_PAIR_5G | LEDS_5G | LEDS_TWO_PAIR_2G5,
+			LEDS_2G5 | LEDS_LINK,
+			LEDS_1G | LEDS_LINK,
+			LEDS_2G5 | LEDS_LINK | LEDS_ACT },
+		    },
+};

machine/DEFAULT_8C_1SFP.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_DEFAULT_8C_1SFP_H_
+#define _MACHINE_DEFAULT_8C_1SFP_H_
+
+#define MACHINE_MODEL "8+1 SFP Port Switch"
+
+#endif

machine/F7008_2_5.c

@@ -0,0 +1,41 @@
+#include "machine_defs.h"
+
+__code const struct machine machine = {
+	.machine_name = MACHINE_MODEL,
+	.isRTL8373 = 1,
+	.min_port = 0,
+	.max_port = 8,
+	.n_sfp = 1,
+	.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
+	.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
+	.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
+	.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
+	.sfp_port[0].pin_los = GPIO37,
+	.sfp_port[0].pin_tx_disable = GPIO_NA,
+	.sfp_port[0].sds = 1,
+	.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
+	.reset_pin = GPIO_NA,
+	.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28_SYS | LED_29 },
+	.port_led_set = {0, 0, 0, 0, 0, 0, 0, 0, 1},
+	.led_sets = {
+		{	/* SET0 */
+			LEDS_2G5 | LEDS_LINK,				/* LEDID0 - green: 2.5G link */
+			LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,	/* LEDID1 - yellow: traffic */
+			0,
+			0,
+		},
+		{	/* SET1 - SFP+ */
+			LEDS_10G | LEDS_5G | LEDS_2G5 | LEDS_LINK,
+			LEDS_10G | LEDS_5G | LEDS_2G5 | LEDS_1G | LEDS_LINK | LEDS_ACT,
+			0,
+			0,
+		},
+	},
+	.led_mux_custom = 1,
+	.led_mux = {
+		0x00, 0x01, 0x04, 0x05, 0x08, 0x09, 0x0c, 0x02,
+		0x0d, 0x10, 0x11, 0x02, 0x14, 0x02, 0x02, 0x15,
+		0x02, 0x02, 0x18, 0x02, 0x02, 0x19, 0x02, 0x02,
+		0x1c, 0x1d, 0x02, 0x02,
+	},
+};

machine/F7008_2_5.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_F7008_2_5_H_
+#define _MACHINE_F7008_2_5_H_
+
+#define MACHINE_MODEL "F7008-2.5 8+1 SFP Port Switch"
+
+#endif

machine/FG_4GT_2SX_V2_0.c

@@ -0,0 +1,66 @@
+#include "machine_defs.h"
+
+__code const struct machine machine = {
+	.machine_name = MACHINE_MODEL,
+	.isRTL8373 = 0,
+	.min_port = 3,
+	.max_port = 8,
+	.n_sfp = 2,
+	.log_to_phys_port = {0, 0, 0, 6, 1, 2, 3, 4, 5},
+	.phys_to_log_port = {4, 5, 6, 7, 8, 3, 0, 0, 0},
+	.is_sfp = {0, 0, 0, 2, 0, 0, 0, 0, 1},
+	
+	// Left SFP port
+	.sfp_port[0].pin_detect = GPIO38, 
+	.sfp_port[0].pin_los = GPIO_NA, 
+	.sfp_port[0].sds = 1, 
+	.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
+
+	// Right SFP port
+	.sfp_port[1].pin_detect = GPIO37,
+	.sfp_port[1].pin_los = GPIO_NA, 
+	.sfp_port[1].sds = 0, 
+	.sfp_port[1].i2c = I2CBUS( GPIO41_I2C_SDA3_MDIO1, GPIO40_I2C_SCL3_MDC1 ),
+
+	.reset_pin = GPIO_NA,
+	.high_leds = { .mux = LED_27 | LED_28_SYS | LED_29, .enable = LED_28_SYS | LED_29 },
+	.port_led_set = { 0, 0, 0, 1, 0, 0, 0, 0, 1},
+	/* Ports 1-4 RJ45 use set 0, port 5-6 SFP uses set 1 
+	 * Ports 1-4: Green: 2.5GBit, Amber: 10/100/1000MBit
+	 * Ports 5-6: Green: 100MBit-10GBit
+	 */
+	.led_sets = { 
+			{
+				LEDS_2G5 | LEDS_LINK | LEDS_ACT,
+				LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
+				0,
+				LEDS_2G5 | LEDS_LINK | LEDS_ACT
+			},
+			{  
+				LEDS_10G | LEDS_5G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
+				LEDS_10G | LEDS_LINK,
+				0,
+				LEDS_COL | LEDS_DUPLEX
+			},
+			{
+				LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
+				LEDS_2G5 | LEDS_1G | LEDS_LINK,
+				LEDS_5G | LEDS_2G5 | LEDS_LINK | LEDS_ACT,
+				LEDS_10G | LEDS_LINK | LEDS_ACT
+			},
+			{
+				LEDS_TX,
+				LEDS_RX,
+				LEDS_10G | LEDS_TWO_PAIR_5G | LEDS_5G | LEDS_TWO_PAIR_2G5 |
+					LEDS_2G5 | LEDS_TWO_PAIR_1G | LEDS_1G | LEDS_500M | LEDS_100M | LEDS_10M | LEDS_ACT,
+				LEDS_10G | LEDS_TWO_PAIR_5G | LEDS_5G | LEDS_TWO_PAIR_2G5 |
+					LEDS_2G5 | LEDS_TWO_PAIR_1G | LEDS_1G | LEDS_500M | LEDS_100M | LEDS_10M | LEDS_LINK
+			},
+	 },
+	.led_mux_custom = 1,
+	.led_mux = {
+				0x0c, 0x0d, 0x0e, 0x10, 0x11, 0x12, 0x14, 0x3f, 0x15, 0x16,
+				0x18, 0x0e, 0x19, 0x11, 0x12, 0x1a, 0x15, 0x16, 0x1c, 0x19,
+				0x1a, 0x1d, 0x1d, 0x1e, 0x1e, 0x20, 0x21, 0x22
+		},
+	};

machine/FG_4GT_2SX_V2_0.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_FG_4GT_2SX_V2_0_H_
+#define _MACHINE_FG_4GT_2SX_V2_0_H_
+
+#define MACHINE_MODEL "FG-4GT-2SX_V2.0"
+
+#endif

machine/FG_8GT_1SX.c

@@ -0,0 +1,45 @@
+#include "machine_defs.h"
+
+__code const struct machine machine = {
+	.machine_name = MACHINE_MODEL,
+	.isRTL8373 = 1,
+	.min_port = 0,
+	.max_port = 8,
+	.n_sfp = 1,
+	.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
+	.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
+	.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
+	.sfp_port[0].pin_detect = GPIO38,
+	.sfp_port[0].pin_los = GPIO_NA,
+	.sfp_port[0].pin_tx_disable = GPIO_NA,
+	.sfp_port[0].sds = 1,
+	.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
+	.reset_pin = GPIO_NA,
+	.high_leds = { .mux = LED_27 | LED_28_SYS | LED_29, .enable = LED_28_SYS | LED_29 },
+	.port_led_set = {0, 0, 0, 0, 0, 0, 0, 0, 1},
+	.led_sets = {
+		/*
+			Ports 1-8: Left Amber 10/100/1000MBit (Vendor no 10M, but we add it)
+					   Right Green 2.5GBit
+			SFP-port: Any speed
+		*/
+		{
+			LEDS_2G5 | LEDS_LINK | LEDS_ACT,
+			LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
+			0,
+			0,
+		},
+		{
+			LEDS_10G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
+			0,
+			0,
+			0,
+		},
+	},
+	.led_mux_custom = 1,
+	.led_mux = {
+		0x00, 0x01, 0x04, 0x05, 0x08, 0x09, 0x0c, 0x09, 0x0d, 0x10,
+		0x11, 0x0e, 0x14, 0x11, 0x12, 0x15, 0x15, 0x16, 0x18, 0x19,
+		0x1a, 0x19, 0x1d, 0x1e, 0x1c, 0x1d, 0x20, 0x21,
+	},
+};

machine/FG_8GT_1SX.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_FG_8GT_1SX_H_
+#define _MACHINE_FG_8GT_1SX_H_
+
+#define MACHINE_MODEL "FG-8GT-1SX"
+
+#endif

machine/FNS1200P.c

@@ -0,0 +1,55 @@
+#include "machine_defs.h"
+
+__code const struct machine machine = {
+    .machine_name = MACHINE_MODEL,
+    .isRTL8373 = 0,
+    .min_port = 3,
+    .max_port = 8,
+    .n_sfp = 2,
+    .log_to_phys_port = {0, 0, 0, 6, 1, 2, 3, 4, 5},
+    .phys_to_log_port = {4, 5, 6, 7, 8, 3, 0, 0, 0},
+    .is_sfp = {0, 0, 0, 2, 0, 0, 0, 0, 1},
+
+    /* Left SFP (logical 8, SDS1): GPIO30=ModAbs, GPIO37=RX_LOS */
+    .sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
+    .sfp_port[0].pin_los = GPIO37,
+    .sfp_port[0].pin_tx_disable = GPIO_NA,
+    .sfp_port[0].sds = 1,
+    .sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
+
+    /* Right SFP (logical 3, SDS0): GPIO50=ModAbs, GPIO51=RX_LOS */
+    .sfp_port[1].pin_detect = GPIO50_I2C_SCL2_UART1_TX,
+    .sfp_port[1].pin_los = GPIO51_I2C_SDA2_UART1_RX,
+    .sfp_port[1].pin_tx_disable = GPIO_NA,
+    .sfp_port[1].sds = 0,
+    .sfp_port[1].i2c = I2CBUS( GPIO41_I2C_SDA3_MDIO1, GPIO40_I2C_SCL3_MDC1 ),
+
+    .reset_pin = GPIO_NA,
+
+    .high_leds = { .mux = LED_27 | LED_28_SYS | LED_29, .enable = LED_28_SYS | LED_29 },
+
+    /* Copper ports use SET0; SFP ports use SET1 */
+    .port_led_set = {0, 0, 0, 1, 0, 0, 0, 0, 1},
+
+    .led_sets = {
+        {   /* SET0: copper — LED0=amber (2.5G), LED2=green (1G/100M/10M) */
+            LEDS_2G5 | LEDS_LINK | LEDS_ACT,
+            0,
+            LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
+            0
+        },
+        {   /* SET1: SFP — all speeds link/act */
+            LEDS_10G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
+            0,
+            0, 0
+        },
+    },
+
+    .led_mux_custom = 1,
+    .led_mux = {
+        0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f,  /* GPIO0-7: unused */
+        0x0f, 0x0c, 0x0d, 0x0e, 0x10, 0x11, 0x12,          /* GPIO8-14 */
+        0x14, 0x15, 0x16, 0x18, 0x19, 0x1a,                 /* GPIO15-20 */
+        0x1c, 0x1d, 0x1e, 0x20, 0x21, 0x22, 0x23            /* GPIO21-27 */
+    },
+};

machine/FNS1200P.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_FNS1200P_H_
+#define _MACHINE_FNS1200P_H_
+
+#define MACHINE_MODEL "FNS-1200P"
+
+#endif

machine/HASIVO_S1100WP_8GT_1SX_SE.c

@@ -0,0 +1,32 @@
+#include "machine_defs.h"
+
+__code const struct machine machine = {
+	.machine_name = MACHINE_MODEL,
+	.isRTL8373 = 1,
+	.mac_flash_offset = 0x1FC000,
+	.min_port = 0,
+	.max_port = 8,
+	.n_sfp = 1,
+	.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
+	.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
+	.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
+	.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
+	.sfp_port[0].pin_los = GPIO37,
+	.sfp_port[0].pin_tx_disable = GPIO_NA,
+	.sfp_port[0].sds = 1,
+	.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
+	.reset_pin = GPIO54_ACL_BIT2_EN,
+	.high_leds = { .mux = LED_27 | LED_28_SYS | LED_29, .enable = LED_28_SYS | LED_29 },
+	.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1},
+	.led_sets = { { LEDS_2G5 | LEDS_LINK | LEDS_ACT, // Green LED (right)
+					0,
+					LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT, // Amber LED (left)
+					0
+				  },
+				  { LEDS_10G | LEDS_5G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_LINK | LEDS_ACT, // SFP LED
+					0, 
+					0,
+					0
+				  },
+				},
+};

machine/HASIVO_S1100WP_8GT_1SX_SE.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_HASIVO_S1100WP_8GT_1SX_SE_H_
+#define _MACHINE_HASIVO_S1100WP_8GT_1SX_SE_H_
+
+#define MACHINE_MODEL "Hasivo S1100WP-8GT-1SX-SE"
+
+#endif

machine/HASIVO_S600W_4GT_2XGT_SE.c

@@ -0,0 +1,43 @@
+#include "machine_defs.h"
+
+__code const struct machine machine = {
+    .machine_name = MACHINE_MODEL,
+    .isRTL8373 = 0,
+    .min_port = 3,
+    .max_port = 8,
+    .n_sfp = 0,
+    .n_10g = 2,
+    .log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
+    .phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
+    .is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 0},
+    .reset_pin = GPIO54_ACL_BIT2_EN,
+    .high_leds = { .mux = LED_28_SYS | LED_29, .enable = LED_28_SYS | LED_29 },
+    .port_led_set = { 0, 0, 0, 1, 0, 0, 0, 0, 1 },
+    /* Ports 1-4: Green: 2.5GBit, Orange: 10/100/1000MBit
+     * Ports 5-6: Green: 10GBit, Orange: 5/2.5GBit, None: 10/100/1000MBit
+     */
+    .led_sets = {
+        {
+            LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT, // Yellow
+            LEDS_2G5 | LEDS_LINK, // Green
+            LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK, // Orange
+            0, // Unused
+        },
+        {
+            LEDS_10G | LEDS_5G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT, // Yellow
+            LEDS_10G | LEDS_LINK, // Green
+            LEDS_5G | LEDS_2G5 | LEDS_LINK, // Orange
+            0, // Unused
+        },
+    },
+    .led_mux_custom = 1,
+    .led_mux = {
+        0x3f, 0x3f, 0x3f, 0x3f, 0x3f,
+        0x3f, 0x3f, 0x3f, 0x0f, 0x20,
+        0x21, 0x22, 0x10, 0x11, 0x12,
+        0x14, 0x15, 0x16, 0x18, 0x19,
+        0x1a, 0x1c, 0x1d, 0x1e, 0x0c,
+        0x0d, 0x0e, 0x23
+    },
+
+};

machine/HASIVO_S600W_4GT_2XGT_SE.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_HASIVO_S600W_4GT_2XGT_SE_H_
+#define _MACHINE_HASIVO_S600W_4GT_2XGT_SE_H_
+
+#define MACHINE_MODEL "Hasivo S600W-4GT-2XGT-SE"
+
+#endif

machine/HG0402XG_V1_1.c

@@ -0,0 +1,38 @@
+#include "machine_defs.h"
+
+__code const struct machine machine = {
+	.machine_name = MACHINE_MODEL,
+	.isRTL8373 = 0,
+	.min_port = 3,
+	.max_port = 8,
+	.n_sfp = 2,
+	.log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
+	.phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
+	.is_sfp = {0, 0, 0, 2, 0, 0, 0, 0, 1},
+	.sfp_port[0].pin_detect = 50,
+	.sfp_port[0].pin_los = 10,
+	.sfp_port[0].pin_tx_disable = GPIO_NA,
+	.sfp_port[0].sds = 1,
+	.sfp_port[0].i2c = I2CBUS( GPIO41_I2C_SDA3_MDIO1, GPIO40_I2C_SCL3_MDC1 ),
+	.sfp_port[1].pin_detect = 30,
+	.sfp_port[1].pin_los = 51,
+	.sfp_port[1].pin_tx_disable = GPIO_NA,
+	.sfp_port[1].sds = 0,
+	.sfp_port[1].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
+	.reset_pin = GPIO_NA,
+	.high_leds = { .mux = LED_27 , .enable = LED_27 | LED_29 },
+	.port_led_set = { 0, 0, 0, 1, 0, 0, 0, 0, 1},
+	/* The Ethernet ports have 1 amber LED (left) and 1 green LED (right)
+	 * The SFP ports have also 1 amber LED and 1 green LED
+	 * Ethernet ports use LED-set 0, SFP ports use LED-set 1
+	 */
+	.led_sets = { { LEDS_10M | LEDS_LINK | LEDS_ACT,
+			LEDS_1G | LEDS_100M | LEDS_10M | LEDS_2G5 | LEDS_LINK | LEDS_ACT,
+			LEDS_2G5 | LEDS_LINK | LEDS_ACT,
+			0 },
+			{ LEDS_100M | LEDS_10M | LEDS_LINK,
+			LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
+			LEDS_10G | LEDS_LINK,
+			0 },
+		    },
+};

machine/HG0402XG_V1_1.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_HG0402XG_V1_1_H_
+#define _MACHINE_HG0402XG_V1_1_H_
+
+#define MACHINE_MODEL "HG0402XG V1.1"
+
+#endif

machine/HI_K0402WS.c

@@ -0,0 +1,46 @@
+#include "machine_defs.h"
+
+__code const struct machine machine = {
+	.machine_name = MACHINE_MODEL,
+	.isRTL8373 = 0,
+	.min_port = 3,
+	.max_port = 8,
+	.n_sfp = 2,
+	.log_to_phys_port = {0, 0, 0, 6, 1, 2, 3, 4, 5},
+	.phys_to_log_port = {4, 5, 6, 7, 8, 3, 0, 0, 0},
+	.is_sfp = {0, 0, 0, 2, 0, 0, 0, 0, 1},
+	
+	// Left SFP port
+	.sfp_port[0].pin_detect = GPIO38, 
+	.sfp_port[0].pin_los = GPIO_NA, 
+	.sfp_port[0].sds = 1, 
+	.sfp_port[0].i2c =  I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
+
+	// Right SFP port
+	.sfp_port[1].pin_detect = GPIO37,
+	.sfp_port[1].pin_los = GPIO_NA, 
+	.sfp_port[1].sds = 0, 
+	.sfp_port[1].i2c = I2CBUS( GPIO41_I2C_SDA3_MDIO1, GPIO40_I2C_SCL3_MDC1 ),
+
+	.reset_pin = GPIO_NA,
+	.high_leds = { .mux =  LED_28_SYS | LED_29, .enable = LED_27 | LED_28_SYS | LED_29 },
+	.port_led_set = { 0, 0, 0, 1, 0, 0, 0, 0, 1},
+	.led_sets = { 
+			{
+				LEDS_2G5 | LEDS_LINK | LEDS_10M | LEDS_ACT,
+				LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
+				LEDS_1G | LEDS_LINK, 
+				0 
+			},
+			{  
+				LEDS_10G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK,
+				LEDS_10G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_ACT,
+				0,
+				0
+			},
+	 },
+	.led_mux_custom = 1,
+	.led_mux = {
+				0x00,0x01,0x04,0x05,0x08,0x09,0x0c,0x3f,0x0d,0x10,0x11,0x0e,0x14,0x11,0x12,0x15,0x15,0x16,0x18,0x19,0x1a,0x19,0x1d,0x1e,0x1c,0x1d,0x20,0x21
+		},
+	};

machine/HI_K0402WS.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_HI_K0402WS_H_
+#define _MACHINE_HI_K0402WS_H_
+
+#define MACHINE_MODEL "PCB-K0402WS-V3.0"
+
+#endif

machine/HI_K0801WS.c

@@ -0,0 +1,45 @@
+#include "machine_defs.h"
+
+__code const struct machine machine = {
+    .machine_name = MACHINE_MODEL,
+    .isRTL8373 = 1,
+    .min_port = 0,
+    .max_port = 8,
+    .n_sfp = 1,
+    .log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
+    .phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
+    .is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
+
+    .sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
+    .sfp_port[0].pin_los = GPIO37,
+    .sfp_port[0].pin_tx_disable = GPIO_NA,
+    .sfp_port[0].sds = 1,
+    .sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
+    .reset_pin = GPIO_NA,
+
+    .high_leds = {
+        .mux = LED_27 | LED_29,
+        .enable = LED_28_SYS | LED_29
+    },
+
+    /* Ports 1-8 use set 0, port 9 SFP uses set 1 */
+    .port_led_set = {0, 0, 0, 0, 0, 0, 0, 0, 1},
+
+    .led_sets = {
+        {   /* Set 0: RJ45 copper ports
+             * Amber = 2.5G
+             * Green = 1G/100M/10M with activity
+             */
+            LEDS_2G5 | LEDS_LINK | LEDS_ACT, /* Amber */
+            0,
+            LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT, /* Green */
+            0
+        },
+        {   /* Set 1: SFP port, single green LED for all valid speeds */
+            LEDS_10G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
+            0,
+            0,
+            0
+        },
+    },
+};

machine/HI_K0801WS.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_HI_K0801WS_H_
+#define _MACHINE_HI_K0801WS_H_
+
+#define MACHINE_MODEL "Hi-Source HI-k0801WS"
+
+#endif

machine/K0501W_V2_0.c

@@ -0,0 +1,34 @@
+#include "machine_defs.h"
+
+__code const struct machine machine = {
+	.machine_name = MACHINE_MODEL,
+	.isRTL8373 = 0,
+	.min_port = 3,
+	.max_port = 8,
+	.n_sfp = 1,
+	.log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
+	.phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
+	.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
+	.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
+	.sfp_port[0].pin_los = GPIO37,
+	.sfp_port[0].pin_tx_disable = GPIO_NA,
+	.sfp_port[0].sds = 1,
+	.sfp_port[0].i2c =  I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
+
+	.reset_pin = GPIO_NA,
+	.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1},
+	.led_sets = {
+		{
+			LEDS_2G5 | LEDS_LINK | LEDS_ACT,
+			0,
+			LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
+			0
+		},
+		{
+			LEDS_10G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
+			0,
+			0,
+			0
+		},
+	 },
+};

machine/K0501W_V2_0.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_K0501W_V2_0_H_
+#define _MACHINE_K0501W_V2_0_H_
+
+#define MACHINE_MODEL "K0501W V2.0"
+
+#endif

machine/KP_9000_6XHML_X2.c

@@ -0,0 +1,37 @@
+#include "machine_defs.h"
+
+__code const struct machine machine = {
+	.machine_name = MACHINE_MODEL,
+	.isRTL8373 = 0,
+	.min_port = 3,
+	.max_port = 8,
+	.n_sfp = 2,
+	.log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
+	.phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
+	.is_sfp = {0, 0, 0, 1, 0, 0, 0, 0, 2},
+	// Left SFP port (5)
+	.sfp_port[0].pin_detect = GPIO50_I2C_SCL2_UART1_TX,
+	.sfp_port[0].pin_los = GPIO10_LED10,
+	.sfp_port[0].pin_tx_disable = GPIO_NA,
+	.sfp_port[0].sds = 0,
+	.sfp_port[0].i2c = I2CBUS( GPIO41_I2C_SDA3_MDIO1, GPIO40_I2C_SCL3_MDC1 ),
+	// Right SFP port (6)
+	.sfp_port[1].pin_detect = GPIO30_ACL_BIT3_EN,
+	.sfp_port[1].pin_los = GPIO37,
+	.sfp_port[1].pin_tx_disable = GPIO_NA,
+	.sfp_port[1].sds = 1,
+	.sfp_port[1].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
+	.reset_pin = GPIO54_ACL_BIT2_EN,
+	.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28_SYS | LED_29 },
+	.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 0},
+	/* Conditions for LED on:
+	 * dual led orange: ledset_0 & ledset_2
+	 * dual led green: ledset_2 & !ledset_0
+	 * single right led green: ledset_0 & !ledset_1
+	*/
+	.led_sets = { { LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
+			LEDS_2G5 | LEDS_LINK | LEDS_10G,
+			LEDS_1G | LEDS_LINK,
+			0 },
+		    },
+};

machine/KP_9000_6XHML_X2.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_KP_9000_6XHML_X2_H_
+#define _MACHINE_KP_9000_6XHML_X2_H_
+
+#define MACHINE_MODEL "keepLink KP-9000-6XHML-X2"
+
+#endif

machine/KP_9000_6XHML_X2_V1_1.c

@@ -0,0 +1 @@
+KP_9000_6XHML_X2.c

machine/KP_9000_6XHML_X2_V1_1.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_KP_9000_6XHML_X2_V1_1_H_
+#define _MACHINE_KP_9000_6XHML_X2_V1_1_H_
+
+#define MACHINE_MODEL "keepLink KP-9000-6XHML V1.1"
+
+#endif

machine/KP_9000_6XHML_X2_V1_2.c

@@ -0,0 +1 @@
+KP_9000_6XHML_X2.c

machine/KP_9000_6XHML_X2_V1_2.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_KP_9000_6XHML_X2_V1_2_H_
+#define _MACHINE_KP_9000_6XHML_X2_V1_2_H_
+
+#define MACHINE_MODEL "keepLink KP-9000-6XHML V1.2"
+
+#endif

machine/KP_9000_6XHML_X2_V2_1.c

@@ -0,0 +1 @@
+KP_9000_6XH_X2.c

machine/KP_9000_6XHML_X2_V2_1.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_KP_9000_6XHML_X2_V2_1_H_
+#define _MACHINE_KP_9000_6XHML_X2_V2_1_H_
+
+#define MACHINE_MODEL "keepLink KP-9000-6XHML V2.1"
+
+#endif

machine/KP_9000_6XH_X.c

@@ -0,0 +1,28 @@
+#include "machine_defs.h"
+
+__code const struct machine machine = {
+	.machine_name = MACHINE_MODEL,
+	.isRTL8373 = 0,
+	.min_port = 3,
+	.max_port = 8,
+	.n_sfp = 1,
+	.log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
+	.phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
+	.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
+	.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
+	.sfp_port[0].pin_los = GPIO37,
+	.sfp_port[0].pin_tx_disable = GPIO_NA,
+	.sfp_port[0].sds = 1,
+	.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
+	.reset_pin = GPIO_NA,
+	/* Conditions for LED on:
+	 * dual led orange: ledset_0 & ledset_2
+	 * dual led green: ledset_2 & !ledset_0
+	 * single right led green: ledset_0 & !ledset_1
+	*/
+	.led_sets = { { LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
+			LEDS_2G5 | LEDS_LINK | LEDS_10G,
+			LEDS_1G | LEDS_LINK,
+			0 },
+		    },
+};

machine/KP_9000_6XH_X.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_KP_9000_6XH_X_H_
+#define _MACHINE_KP_9000_6XH_X_H_
+
+#define MACHINE_MODEL "keepLink KP-9000-6XH-X"
+
+#endif

machine/KP_9000_6XH_X2.c

@@ -0,0 +1,48 @@
+#include "machine_defs.h"
+
+__code const struct machine machine = {
+	.machine_name = MACHINE_MODEL,
+	.isRTL8373 = 0,
+	.min_port = 3,
+	.max_port = 8,
+	.n_sfp = 2,
+	.log_to_phys_port = {0, 0, 0, 6, 1, 2, 3, 4, 5},
+	.phys_to_log_port = {4, 5, 6, 7, 8, 3, 0, 0, 0},
+	.is_sfp = {0, 0, 0, 2, 0, 0, 0, 0, 1},
+
+	// Left SFP port
+	.sfp_port[0].pin_detect = GPIO38,
+	.sfp_port[0].pin_los = GPIO_NA,
+	.sfp_port[0].sds = 1,
+	.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
+
+	// Right SFP port
+	.sfp_port[1].pin_detect = GPIO37,
+	.sfp_port[1].pin_los = GPIO_NA,
+	.sfp_port[1].sds = 0,
+	.sfp_port[1].i2c = I2CBUS( GPIO41_I2C_SDA3_MDIO1, GPIO40_I2C_SCL3_MDC1 ),
+
+	.reset_pin = GPIO48_I2C_SCL1,   // Button-Switch is unpopulated on PCB, but can be added manually (hole in case is already there)
+	.high_leds = { .mux =  LED_28_SYS | LED_29, .enable = LED_27 | LED_28_SYS | LED_29 },
+	.port_led_set = { 0, 0, 0, 1, 0, 0, 0, 0, 1},
+	.led_sets = {
+			{
+				LEDS_2G5 | LEDS_LINK,												// Left LED (Amber)
+				LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,   // Right LED (Green)
+				0,
+				0
+			},
+			{
+				LEDS_10G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
+				0,
+				0,
+				0
+			},
+	 },
+	.led_mux_custom = 1,
+	.led_mux = {
+				0x00,0x01,0x04,0x05,0x08,0x09,0x0c,0x3f,0x0d,0x10,
+				0x11,0x0e,0x14,0x11,0x12,0x15,0x15,0x16,0x18,0x19,
+				0x1a,0x19,0x1d,0x1e,0x1c,0x1d,0x20,0x21
+		},
+	};

machine/KP_9000_6XH_X2.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_KP_9000_6XH_X2_H_
+#define _MACHINE_KP_9000_6XH_X2_H_
+
+#define MACHINE_MODEL "keepLink KP-9000-6XH-X2"
+
+#endif

machine/KP_9000_6XH_X2_V1_1.c

@@ -0,0 +1 @@
+KP_9000_6XHML_X2.c

machine/KP_9000_6XH_X2_V1_1.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_KP_9000_6XH_X2_V1_1_H_
+#define _MACHINE_KP_9000_6XH_X2_V1_1_H_
+
+#define MACHINE_MODEL "keepLink KP-9000-6XH V1.1"
+
+#endif

machine/KP_9000_6XH_X2_V1_2.c

@@ -0,0 +1 @@
+KP_9000_6XHML_X2.c

machine/KP_9000_6XH_X2_V1_2.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_KP_9000_6XH_X2_V1_2_H_
+#define _MACHINE_KP_9000_6XH_X2_V1_2_H_
+
+#define MACHINE_MODEL "keepLink KP-9000-6XH V1.2"
+
+#endif

machine/KP_9000_6XH_X2_V2_1.c

@@ -0,0 +1 @@
+KP_9000_6XH_X2.c

machine/KP_9000_6XH_X2_V2_1.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_KP_9000_6XH_X2_V2_1_H_
+#define _MACHINE_KP_9000_6XH_X2_V2_1_H_
+
+#define MACHINE_MODEL "keepLink KP-9000-6XH-X2 V2.1"
+
+#endif

machine/KP_9000_9XHML_X_V2_2.c

@@ -0,0 +1,51 @@
+#include "machine_defs.h"
+
+__code const struct machine machine = {
+	.machine_name = MACHINE_MODEL,
+	.isRTL8373 = 1,
+	.min_port = 0,
+	.max_port = 8,
+	.n_sfp = 1,
+	.log_to_phys_port = { 1, 2, 3, 4, 5, 6, 7, 8, 9 },
+	.phys_to_log_port = { 0, 1, 2, 3, 4, 5, 6, 7, 8 },
+	.is_sfp = { 0, 0, 0, 0, 0, 0, 0, 0, 1 },
+	.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
+	.sfp_port[0].pin_los = GPIO37,
+	.sfp_port[0].pin_tx_disable = GPIO_NA,
+	.sfp_port[0].sds = 1,
+	.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
+	.reset_pin = GPIO54_ACL_BIT2_EN,
+	.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28_SYS | LED_29 },
+	.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1 },
+	.led_sets = {
+		{   /* Set 0 for RJ45 connectors */
+			/* LED0: Right Green */
+			LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
+			/* LED1: Left Orange */
+			LEDS_2G5 | LEDS_LINK,
+			/* LED2: Left Green */
+			LEDS_1G | LEDS_LINK,
+			/* LED3: None */
+			0,
+		}, { /* Set 1 for SFP port */
+			/* LED0: Single Green "9" LED */
+			LEDS_2G5 | LEDS_TWO_PAIR_1G | LEDS_1G | LEDS_500M | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G | LEDS_TWO_PAIR_5G | LEDS_5G | LEDS_TWO_PAIR_2G5,
+			/* LED1: D23 LED on PCB */
+			LEDS_1G | LEDS_LINK,
+			/* LED2: D22 LED on PCB */
+			LEDS_2G5 | LEDS_LINK,
+			/* LED3: Unused */
+			LEDS_COL | LEDS_DUPLEX,
+		}, { /* Set 2: Unused, but set to same things as stock firmware for consistency */
+			LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
+			LEDS_1G | LEDS_LINK | LEDS_ACT,
+			LEDS_2G5 | LEDS_LINK | LEDS_ACT | LEDS_5G,
+			LEDS_10G | LEDS_ACT | LEDS_LINK,
+		}, { /* Set 3: Unused, but set to same things as stock firmware for consistency */
+			LEDS_TX,
+			LEDS_RX,
+			LEDS_2G5 | LEDS_TWO_PAIR_1G | LEDS_1G | LEDS_500M | LEDS_100M | LEDS_10M | LEDS_ACT | LEDS_10G | LEDS_TWO_PAIR_5G | LEDS_5G | LEDS_TWO_PAIR_2G5,
+			LEDS_2G5 | LEDS_TWO_PAIR_1G | LEDS_1G | LEDS_500M | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_10G | LEDS_TWO_PAIR_5G | LEDS_5G | LEDS_TWO_PAIR_2G5,
+		},
+	},
+};

machine/KP_9000_9XHML_X_V2_2.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_KP_9000_9XHML_X_V2_2_H_
+#define _MACHINE_KP_9000_9XHML_X_V2_2_H_
+
+#define MACHINE_MODEL "keepLink KP-9000-9XHML-X V2.2"
+
+#endif

machine/KP_9000_9XHML_X_V3_1.c

@@ -0,0 +1,37 @@
+#include "machine_defs.h"
+
+// 2M-PCB23-V3.2 is wired like V3.1 (SFP detection, LEDs, factory MAC location)
+__code const struct machine machine = {
+	.machine_name = MACHINE_MODEL,
+	.isRTL8373 = 1,
+	.min_port = 0,
+	.max_port = 8,
+	.n_sfp = 1,
+	.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
+	.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
+	.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
+	.sfp_port[0].pin_detect = GPIO38,
+	.sfp_port[0].pin_los = GPIO_NA,
+	.sfp_port[0].sds = 1,
+	.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
+	.reset_pin = GPIO48_I2C_SCL1,
+	.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28_SYS | LED_29 },
+	.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1},
+	.led_sets = {
+		{   /* RJ45: First LED, yellow, second LED: green */
+			LEDS_2G5 | LEDS_LINK,
+            LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
+			0,
+			0,
+		}, { /* SFP PORT, SINGLE GREEN LED */
+			LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
+			0,
+			0,
+			0,
+		}},
+	.led_mux_custom = 1,
+	.led_mux = {0x00, 0x01, 0x04, 0x05, 0x08, 0x09, 0x0c, 0x09, 0x0d, 0x10,
+				0x11, 0x0e, 0x14, 0x11, 0x12, 0x15, 0x15, 0x16, 0x18, 0x19,
+				0x1a, 0x19, 0x1d, 0x1e, 0x1c, 0x1d, 0x20, 0x21},
+	.mac_flash_offset = 0x1FC000,
+};

machine/KP_9000_9XHML_X_V3_1.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_KP_9000_9XHML_X_V3_1_H_
+#define _MACHINE_KP_9000_9XHML_X_V3_1_H_
+
+#define MACHINE_MODEL "keepLink KP-9000-9XHML-X V3.1"
+
+#endif

machine/KP_9000_9XHML_X_V3_2.c

@@ -0,0 +1 @@
+KP_9000_9XHML_X_V3_1.c

machine/KP_9000_9XHML_X_V3_2.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_KP_9000_9XHML_X_V3_2_H_
+#define _MACHINE_KP_9000_9XHML_X_V3_2_H_
+
+#define MACHINE_MODEL "keepLink KP-9000-9XHML-X V3.2"
+
+#endif

machine/KP_9000_9XH_X_EU.c

@@ -0,0 +1,25 @@
+#include "machine_defs.h"
+
+__code const struct machine machine = {
+	.machine_name = MACHINE_MODEL,
+	.isRTL8373 = 1,
+	.min_port = 0,
+	.max_port = 8,
+	.n_sfp = 1,
+	.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
+	.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
+	.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
+	.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
+	.sfp_port[0].pin_los = GPIO37,
+	.sfp_port[0].pin_tx_disable = GPIO_NA,
+	.sfp_port[0].sds = 1,
+	.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
+	.reset_pin = GPIO_NA,
+	.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28_SYS | LED_29 },
+	.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 0},
+	.led_sets = { { LEDS_2G5 | LEDS_TWO_PAIR_1G | LEDS_1G | LEDS_500M | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G | LEDS_TWO_PAIR_5G | LEDS_5G | LEDS_TWO_PAIR_2G5,
+			LEDS_2G5 | LEDS_LINK,
+			LEDS_1G | LEDS_LINK, 
+			LEDS_2G5 | LEDS_LINK | LEDS_ACT },
+		    },
+};

machine/KP_9000_9XH_X_EU.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_KP_9000_9XH_X_EU_H_
+#define _MACHINE_KP_9000_9XH_X_EU_H_
+
+#define MACHINE_MODEL "keepLink KP-9000-9XH-X-EU"
+
+#endif

machine/LIANGUO_HYWS_SGT0108S.c

@@ -0,0 +1,36 @@
+#include "machine_defs.h"
+
+__code const struct machine machine = {
+    .machine_name = MACHINE_MODEL,
+    .isRTL8373 = 1,
+    .min_port = 0,
+    .max_port = 8,
+    .n_sfp = 1,
+    .log_to_phys_port = {2, 1, 4, 3, 5, 6, 7, 8, 9},
+    .phys_to_log_port = {1, 0, 3, 2, 4, 5, 6, 7, 8},
+    .is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
+
+    .sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
+    .sfp_port[0].pin_los = GPIO37,
+    .sfp_port[0].pin_tx_disable = GPIO_NA,
+    .sfp_port[0].sds = 1,
+    .sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
+
+    .reset_pin = GPIO_NA,
+	.high_leds = { .mux = 0, .enable = 0 },
+	.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1 },
+	.led_sets = { 
+		{ 
+			LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT, // RJ45 Blue LEDs
+			LEDS_2G5 | LEDS_LINK, // RJ45 White LEDs
+			0,
+			0
+		},
+		{ 
+			LEDS_10G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT, // SFP blue LED?
+			0,
+			0,
+			0
+		},
+	},
+};

machine/LIANGUO_HYWS_SGT0108S.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_LIANGUO_HYWS_SGT0108S_H_
+#define _MACHINE_LIANGUO_HYWS_SGT0108S_H_
+
+#define MACHINE_MODEL "Lianguo HYWS-SGT0108S"
+
+#endif

machine/LIANGUO_ZX_SWTGW215AS.c

@@ -0,0 +1,33 @@
+#include "machine_defs.h"
+
+__code const struct machine machine = {
+	.machine_name = MACHINE_MODEL,
+	.isRTL8373 = 0,
+	.mac_flash_offset = 0x1FC000,
+	.min_port = 3,
+	.max_port = 8,
+	.n_sfp = 1,
+	.log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
+	.phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
+	.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
+	.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
+	.sfp_port[0].pin_los = GPIO37,
+	.sfp_port[0].pin_tx_disable = GPIO_NA,
+	.sfp_port[0].sds = 1,
+	.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
+	.reset_pin = GPIO54_ACL_BIT2_EN,
+	.high_leds = { .mux = LED_27 | LED_28_SYS | LED_29, .enable = LED_28_SYS | LED_29 },
+	.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1},
+	.led_sets = { { LEDS_2G5 | LEDS_LINK | LEDS_ACT, // Green LED (right)
+					0, // unused
+					LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT, // Amber LED (left)
+					0
+				  }, // unused
+				  { LEDS_10G | LEDS_5G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_LINK | LEDS_ACT, // SFP LED
+					0, // unused
+					0, // unused
+					0
+				  }, // unused		    	},
+				},
+	.led_mux_custom = 0,
+};