Merge pull request #500 from 13974684927/add-f7008-2-5

machine: add the F7008-2.5 (GPOE-V1.2) 8+1 target

doc/devices/F7008-2.5.md

@@ -0,0 +1,70 @@
+# F7008-2.5
+
+Documentation for the unmanaged 8 + 1 switch sold as `7018-2.5G` by Guangnianwei
+(光年微), board marking `F7008-2.5`, PCB `F7008-2.5GPOE-V1.2`.
+
+### Brands
+
+| Brand | Type | Managed | PCB | Flash | Chip RTL |
+|-------|------|---------|-----|-------|----------|
+| Guangnianwei (光年微) | 7018-2.5G | No | F7008-2.5GPOE-V1.2 | W25Q64JVSSIQ | 8373N + 8224N |
+
+### What works
+
+- All eight 2.5GBASE-T RJ45 ports at 10/100/1000/2500 Mbps
+- SFP+ port with 1G/2.5G/10G modules
+- LEDs of the eight RJ45 ports
+
+### Not verified
+
+- The LED pads for the SFP+ cage are not mapped yet. The SFP+ lamps are left
+  undriven, so an inserted module lights nothing.
+- The UART header footprint is present but unpopulated, and no boot log could be
+  captured from it, so the baud rate is unknown. There are most likely
+  unpopulated 0-Ohm resistors next to the header; bridging those should bring
+  the console to life.
+
+### Build target
+
+```
+make MACHINE=F7008_2_5
+```
+
+### LED wiring
+
+Measured pad to lamp map (`led_mux` index -> lamp):
+
+| Port | green lamp | yellow lamp |
+|------|-----------|-------------|
+| 1 | pad 0  | pad 1  |
+| 2 | pad 2  | pad 3  |
+| 3 | pad 4  | pad 5  |
+| 4 | pad 6  | pad 8  |
+| 5 | pad 9  | pad 10 |
+| 6 | pad 12 | pad 15 |
+| 7 | pad 18 | pad 21 |
+| 8 | pad 24 | pad 25 |
+
+Pads 7, 11, 13, 14, 16, 17, 19, 20, 22, 23, 26 and 27 do not drive an RJ45 lamp.
+
+The front panel is silkscreened `2.5G: Green / 10/100M: Yellow`, and the target
+follows it: the green lamp is on while the port is linked at 2.5G, the yellow
+lamp blinks while data is flowing.
+
+### PCB overview
+
+The board is marked `F7008-2.5GPOE-V1.2`.
+
+Top side:
+
+<img src="photos/F7008-2.5/PCB-top.jpg" width="600" />
+
+Bottom side:
+
+<img src="photos/F7008-2.5/PCB-bottom.jpg" width="600" />
+
+### Hardware notes
+
+- 4 x `RT4802SNE` magnetics
+- Unpopulated UART header footprint, next to the magnetics
+- Power input 12V 1A, 180 x 84 x 29 mm metal case

doc/supported_devices.md

@@ -36,6 +36,7 @@ The following devices have been tested and are fully working:
 | Xikestore| SKS3200M-4GPY2XF| Yes     | [SWTG024AS-v1.0](devices/SWTG024AS.md)                                    |       | 4 + 2 |
 | XikeStor | SKS3200-8E1X    | Yes     | [SWTG118AS-V2.1-17462](devices/SWTGW218AS.md)                             | 2M    | 8 + 1 |
 | Ztyuav   | Z-QWYT0402      | No      | [PCB-K0402WS-V3.0](devices/PCB-K0402WS-V3.0.md)                           |       | 4 + 2 |
+| Guangnianwei | 7018-2.5G   | No      | [F7008-2.5GPOE-V1.2](devices/F7008-2.5.md)                                | 8M    | 8 + 1 |
 
 For KP-9000-6XH-X2 / KP-9000-6XHML-X2 / Mokerlink 2G040210GSM devices, select
 the machine target by PCB revision. The ML/non-ML or managed/unmanaged label

machine.c

@@ -1325,6 +1325,47 @@ __code const struct machine machine = {
     },
 
 };
+#elif defined MACHINE_F7008_2_5
+__code const struct machine machine = {
+	.machine_name = "F7008-2.5 8+1 SFP Port Switch",
+	.isRTL8373 = 1,
+	.min_port = 0,
+	.max_port = 8,
+	.n_sfp = 1,
+	.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
+	.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
+	.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
+	.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
+	.sfp_port[0].pin_los = GPIO37,
+	.sfp_port[0].pin_tx_disable = GPIO_NA,
+	.sfp_port[0].sds = 1,
+	.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
+	.reset_pin = GPIO_NA,
+	.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28_SYS | LED_29 },
+	.port_led_set = {0, 0, 0, 0, 0, 0, 0, 0, 1},
+	.led_sets = {
+		{	/* SET0 */
+			LEDS_2G5 | LEDS_LINK,				/* LEDID0 - green: 2.5G link */
+			LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,	/* LEDID1 - yellow: traffic */
+			0,
+			0,
+		},
+		{	/* SET1 - SFP+ */
+			LEDS_10G | LEDS_5G | LEDS_2G5 | LEDS_LINK,
+			LEDS_10G | LEDS_5G | LEDS_2G5 | LEDS_1G | LEDS_LINK | LEDS_ACT,
+			0,
+			0,
+		},
+	},
+	.led_mux_custom = 1,
+	.led_mux = {
+		0x00, 0x01, 0x04, 0x05, 0x08, 0x09, 0x0c, 0x02,
+		0x0d, 0x10, 0x11, 0x02, 0x14, 0x02, 0x02, 0x15,
+		0x02, 0x02, 0x18, 0x02, 0x02, 0x19, 0x02, 0x02,
+		0x1c, 0x1d, 0x02, 0x02,
+	},
+};
+
 #else
 	#error "Please select a machine type in machine.h"
 #endif

machine.h

@@ -48,6 +48,7 @@
 // #define MACHINE_POE_2G080110GS
 // #define MACHINE_PB_2132
 // #define MACHINE_HASIVO_S600W_4GT_2XGT_SE
+// #define MACHINE_F7008_2_5
 
 #define LED_27 1
 // SYSTEM LED