Add assmebler injection script

This adds a howto for figuring out LED configuration via tracing
of functions in the originam firmware image. The method also provides
information on PHY and SDS configuration, including PHY patches.

.github/workflows/build.yml

@@ -26,3 +26,5 @@ jobs:
         run: make CI=1 MACHINE="KP_9000_6XHML_X2"
       - name: Make project (8x1/RTL8373)
         run: make CI=1 MACHINE="KP_9000_9XHML_X_V3_1"
+      - name: Make project with the health instrumentation
+        run: make clean && make CI=1 MACHINE="KP_9000_6XHML_X2" HEALTH=1

Makefile

@@ -19,6 +19,10 @@ ifeq ($(MACHINE),)
 else
 	CC_FLAGS += -DMACHINE_$(MACHINE)
 endif
+# Health instrumentation and the "health" console command: HEALTH=1 gmake ...
+ifneq ($(HEALTH),)
+	CC_FLAGS += -DHEALTH
+endif
 
 ifeq ($(CI),1)
 	CC_FLAGS += --Werror
@@ -75,10 +79,13 @@ SRCS += \
 	rtl837x_igmp.c \
 	rtl837x_init.c \
 	rtl837x_leds.c \
+	rtl837x_leds_dump.c \
 	rtl837x_phy.c \
 	rtl837x_pins.c\
 	rtl837x_port.c \
-	rtl837x_stp.c
+	rtl837x_stp.c \
+	rtl837x_lldp.c \
+	rtl837x_storm.c
 SRCS += \
 	httpd/httpd.c \
 	httpd/page_impl.c
@@ -108,11 +115,14 @@ html_min: $(HTML)
 html_data.c html_data.h &: $(HTML) | tools html_min
 	tools/output/fileadder -a $(HTML_LOCATION) -s $(IMAGESIZE) -b BANK1 -z -d $(HTML_MIN) -p html_data
 
-$(VERSION_HEADER):
+$(VERSION_HEADER): FORCE
 	@printf '%s\n' "#ifndef VERSION_H" "#define VERSION_H" \
 		"#define VERSION_SW \"$(VERSION_EXTENSION)\"" \
 		"#define BUILD_DATE \"$(BUILD_DATE)\"" \
-		"#endif" > $(VERSION_HEADER)
+		"#endif" > $(VERSION_HEADER).tmp
+	@cmp -s $(VERSION_HEADER).tmp $(VERSION_HEADER) \
+		&& rm -f $(VERSION_HEADER).tmp \
+		|| mv $(VERSION_HEADER).tmp $(VERSION_HEADER)
 
 httpd: html_data.h
 
@@ -130,10 +140,20 @@ distclean: $(SUBDIRSCLEAN)
 $(SUBDIRSCLEAN):
 	$(MAKE) -C $(@:clean=) clean
 
-$(BUILDDIR)/%.rel: %.c | create_build_dir html_data.h
+# Objects depend on the flags they were built with, through a stamp file that
+# is rewritten only when CC_FLAGS actually changes.
+CCFLAGS_STAMP := $(BUILDDIR)/.ccflags
+
+.PHONY: FORCE
+FORCE:
+
+$(CCFLAGS_STAMP): FORCE | create_build_dir
+	@echo '$(CC_FLAGS)' | cmp -s - $@ 2>/dev/null || echo '$(CC_FLAGS)' > $@
+
+$(BUILDDIR)/%.rel: %.c $(CCFLAGS_STAMP) | create_build_dir html_data.h
 	$(CC) -MMD $(CC_FLAGS) -o $@ -c $<
 
-$(BUILDDIR)/%.rel: %.asm | create_build_dir
+$(BUILDDIR)/%.rel: %.asm $(CCFLAGS_STAMP) | create_build_dir
 	${ASM} ${AFLAGS} -o $@ $<
 #	mv -f $(addprefix $(basename $^), .lst .rel .sym) .
 
@@ -148,11 +168,11 @@ $(BUILDDIR)/rtlplayground-$(FILENAME_EXTENSION).bin: $(BUILDDIR)/rtlplayground.i
 	tools/output/imagebuilder -i $^ $@
 	tools/output/fileadder -a $(DEFAULT_CONFIG_LOCATION) -s $(IMAGESIZE) -d config.txt $@
 	tools/output/fileadder -a $(CONFIG_LOCATION) -s $(IMAGESIZE) -d config.txt $@
-	tools/output/fileadder -a $(HTML_LOCATION) -s $(IMAGESIZE) -z -d $(HTML_MIN) -p html_data -b BANK1 $@
+	tools/output/fileadder -a $(HTML_LOCATION) -s $(IMAGESIZE) -z -d $(HTML_MIN) -b BANK1 $@
 	tools/output/crc_calculator -u $@
 	ln -sf $(MACHINE)/rtlplayground-$(FILENAME_EXTENSION).bin output/rtlplayground.bin
 
-.PHONY: clean distclean all $(SUBDIRS) $(SUBDIRSCLEAN) $(VERSION_HEADER) create_build_dir
+.PHONY: clean distclean all $(SUBDIRS) $(SUBDIRSCLEAN) create_build_dir
 
 .PHONY:
 machine_check:

README.md

@@ -344,6 +344,7 @@ netmask zzz.zzz.zzz.zzz = Network mask of the switch
 port x name xxx         = Name xxx the port number x
 port z 1g               = Set 1g speed for port z
 igmp on/off             = Turn IGMP on or off
+session xxxx            = Web session timeout in seconds (default 200)
 ```
 [To be continue]
 
@@ -359,4 +360,5 @@ The following documents give further documentation on specific features of the R
 - [SFP+ ports](doc/sfp.md) 
 - [Trunking aka. port aggregation](doc/trunking.md)
 - [VLAN](doc/vlan.md)
+- [Storm control](doc/storm_control.md)
 - [Modifications and Flash replacement](doc/mods.md)

boot.c

@@ -21,6 +21,7 @@ extern __code const struct machine machine;
 extern __xdata struct machine_runtime machine_detected;
 extern __xdata uint8_t sfr_data[4];
 extern volatile __xdata uint32_t ticks;
+__xdata uint32_t rtl8224_release_tick;
 extern __xdata uint8_t tx_seq;
 extern __code const uint8_t * __code const hex;
 
@@ -240,10 +241,10 @@ void rtl8224_enable(void) __banked
 	reg_bit_clear(RTL837X_REG_GPIO_32_63_OUTPUT, 4);
 	// Configure Pin as output
 	reg_bit_set(RTL837X_REG_GPIO_32_63_DIRECTION, 4);
-	delay(100);
+	delay(4);
 	// Set pin 4 high
 	reg_bit_set(RTL837X_REG_GPIO_32_63_OUTPUT, 4);
-	delay(500);
+	rtl8224_release_tick = ticks;
 }
 
 

cmd_parser.c

@@ -5,6 +5,8 @@
 // #define DEBUG
 // #define REGDBG 1
 
+#include <8051.h>
+#include "cmd_parser.h"
 #include "rtl837x_common.h"
 #include "rtl837x_port.h"
 #include "rtl837x_flash.h"
@@ -14,6 +16,8 @@
 #include "rtl837x_stp.h"
 #include "rtl837x_igmp.h"
 #include "rtl837x_bandwidth.h"
+#include "rtl837x_lldp.h"
+#include "rtl837x_storm.h"
 #include "sfp.h"
 #include "dhcp.h"
 #include "syslog.h"
@@ -21,6 +25,7 @@
 #include "version.h"
 
 #include "machine.h"
+#include "rtl837x_leds.h"
 #include "phy.h"
 
 #pragma codeseg BANK2
@@ -29,6 +34,7 @@
 extern __code const struct machine machine;
 extern __xdata bool stp_enabled;
 extern __code const uint8_t log_to_phys_port[9];
+extern __xdata bool lldp_enabled;
 
 extern volatile __xdata uint32_t ticks;
 extern volatile __xdata uint8_t sfr_data[4];
@@ -41,6 +47,8 @@ extern __xdata struct flash_region_t flash_region;
 
 extern __xdata char passwd[21];
 
+extern __xdata uint16_t session_timeout;
+
 extern __xdata struct dhcp_state dhcp_state;
 
 __xdata uint8_t vlan_names[VLAN_NAMES_SIZE];
@@ -59,7 +67,6 @@ __xdata uint8_t hexvalue[4] = { 0 };
 
 // Buffer for writing to flash 0x1fd000, copy to 0x1fe000
 __xdata uint8_t cmd_buffer[CMD_BUF_SIZE];
-__xdata uint8_t cmd_available;
 
 __xdata	char save_cmd;
 
@@ -875,6 +882,7 @@ void parse_port(void)
 		cmd_error("\nUsage:" \
 					 "\nport <port> [show|on|off]" \
 					 "\nport <port> [10m|100m|1g|2g5|duplex] [half|full]" \
+					 "\nport <port> lldp [block|permit]" \
 					 "\nport <port> name [custom port name]\n");
 		return;
 	}
@@ -893,10 +901,13 @@ void parse_port(void)
 		print_string_x(port_names[phy_settings.port]);
 		if (!machine.is_sfp[phy_settings.port]) {
 			phy_show(phy_settings.port);
+		} else {
+			write_char('\n');
 		}
+		port_media_show(phy_settings.port);
 	} else if (cmd_compare(2, "name")) {
 		uint8_t i = 0;
-		while ( (i < PORT_NAME_SIZE-1) && (cmd_buffer[cmd_words_b[3] + i] != NUL) ) {
+		while ( cmd_words_len > 3 && (i < PORT_NAME_SIZE-1) && (cmd_buffer[cmd_words_b[3] + i] != NUL) ) {
 			port_names[phy_settings.port][i] = name_char(cmd_buffer[cmd_words_b[3] + i]);
 			i++;
 		}
@@ -904,6 +915,14 @@ void parse_port(void)
 		print_string("\nName set to: \"");
 		print_string_x(port_names[phy_settings.port]);
 		print_string("\"\n");
+	} else if (cmd_compare(2, "lldp")) {
+		if (cmd_compare(3, "block")){
+			lldp_logical_port_status &= ~((uint16_t)1 << phy_settings.port);
+		} else if (cmd_compare(3, "permit")) {
+			lldp_logical_port_status |= (uint16_t)1 << phy_settings.port;
+		} else {
+			print_string ("Unknown port <port> lldp [block|permit] command\n");
+		}
 	} else if (machine.is_sfp[phy_settings.port]) {
 		print_string(" is SFP no PHY information available.\n");
 	} else if (cmd_compare(2, "10m")) {
@@ -1165,6 +1184,32 @@ err:
 }
 
 
+static void print_temperature(uint16_t reg)
+{
+	int16_t v;
+
+	reg_read(reg);
+	v = SFR_DATA_U16;
+	if (v < 0) {
+		write_char('-');
+		v = -v;
+	}
+	itoa(v >> 7);
+	write_char('.');
+	itoa(((v & 0x7f) * 10) >> 7);
+	print_string(" C\n");
+}
+
+
+void parse_temp(void)
+{
+	print_string("\nChip temperature: ");
+	print_temperature(RTL837X_TM_RESULT);
+	print_string("At power-on:      ");
+	print_temperature(RTL837X_TM_RESULT_POWERON);
+}
+
+
 void parse_sdsget(void)
 {
 	__xdata uint8_t sds_id, page, reg, hex_size;
@@ -1541,6 +1586,57 @@ err:
 	cmd_error("bw [in|out|status] <port> [<hexvalue>|off|drop|fc]\n");
 }
 
+static __code const char * __code const storm_types[STORM_TYPES] = { "bcast", "mcast", "ucast", "umcast" };
+
+void parse_storm(void)
+{
+	uint8_t port, type, d;
+	__xdata uint32_t rate;
+	__xdata uint8_t *p;
+
+	if (cmd_words_len == 1)
+		return storm_show();
+	if (cmd_words_len < 4 || !cmd_parse_port_separator(cmd_words_b[1]))
+		goto err;
+	port = atoi_results_u8;
+
+	type = 0;
+	while (!cmd_compare(2, storm_types[type])) {
+		if (++type == STORM_TYPES)
+			goto err;
+	}
+
+	if (cmd_words_len == 4 && cmd_compare(3, "off"))
+		return storm_off(port, type);
+	if (cmd_words_len != 5)
+		goto err;
+
+	rate = 0;
+	p = &cmd_buffer[cmd_words_b[3]];
+	do {
+		d = *p++ - '0';
+		if (d > 9 || rate > 99999999)
+			goto err;
+		rate = (rate << 3) + (rate << 1) + d;
+	} while (*p != ' ' && *p != NUL);
+
+	if (cmd_compare(4, "pps")) {
+		if (!rate || rate > 0xfffff)
+			goto err;
+		storm_set(port, type, rate, 1);
+	} else if (cmd_compare(4, "kbps")) {
+		if (!rate || rate > 10000000)
+			goto err;
+		storm_set(port, type, rate, 0);
+	} else {
+		goto err;
+	}
+	return;
+
+err:
+	print_string("usage: storm [<port> bcast|mcast|ucast|umcast <rate> pps|kbps|off]\n");
+}
+
 void parse_syslog(void)
 {
 	if (cmd_words_len < 2) // no argument -> print status
@@ -1609,6 +1705,25 @@ void parse_syslog(void)
 	}
 }
 
+void parse_session(void)
+{
+	if (cmd_words_len >= 2) {
+		/* atoi_short() returns zero for no digits and for a value past
+		 * 65535; a zero-second timeout is not useful either, so both
+		 * tests are needed. */
+		if (!atoi_short(cmd_words_b[1]) || !atoi_results_short) {
+			print_string("Must be 1-65535 s\n");
+			return;
+		}
+		session_timeout = atoi_results_short;
+	}
+	/* Also the confirmation after setting: one message for both. */
+	print_string("Session timeout: ");
+	itoa_short(session_timeout);
+	print_string(" s\n");
+}
+
+
 // Parse command into words
 // cmd_words_len contains the number of words found.
 // cmd_words_b[] contains only start of a word offset.
@@ -1847,6 +1962,10 @@ void cmd_parser(void) __banked
 			}
 		} else if (cmd_compare(0, "stp")) {
 			stp_parse();
+#ifdef HEALTH
+		} else if (cmd_compare(0, "health")) {
+			health_show();
+#endif
 		} else if (cmd_compare(0, "pvid")) {
 			if (cmd_words_len == 3 && cmd_parse_port_separator(cmd_words_b[1]) != 0
 			    && atoi_short(cmd_words_b[2]) && atoi_results_short && atoi_results_short <= 4094)
@@ -1869,6 +1988,8 @@ void cmd_parser(void) __banked
 			write_char('\n');
 		} else if (cmd_compare(0, "gpio")) {
 			print_gpio_status();
+		} else if (cmd_compare(0, "leds")) {
+			leds_dump();
 		} else if (cmd_compare(0, "regget")) {
 			parse_regget();
 		} else if (cmd_compare(0, "regset")) {
@@ -1889,6 +2010,10 @@ void cmd_parser(void) __banked
 			parse_eee();
 		} else if (cmd_compare(0, "bw")) {
 			parse_bw();
+		} else if (cmd_compare(0, "temp")) {
+			parse_temp();
+		} else if (cmd_compare(0, "storm")) {
+			parse_storm();
 		} else if (cmd_compare(0, "version")) {
 			print_sw_version();
 		} else if (cmd_compare(0, "time")) {
@@ -1911,6 +2036,16 @@ void cmd_parser(void) __banked
 			}
 		} else if (cmd_compare(0, "ingress")) {
 			parse_ingress();
+		} else if (cmd_compare(0, "session")) {
+			parse_session();
+		} else if (cmd_compare(0, "lldp")) {
+			if (cmd_compare(1, "on")) {
+				print_string("LLDP enabled\n");
+				lldp_enabled = 1;
+			} else {
+				print_string("LLDP disabled\n");
+				lldp_enabled = 0;
+			}
 		}
 		else {
 			cmd_error("Unknown command\n");
@@ -2051,3 +2186,161 @@ void execute_commands(__xdata uint8_t *p) __banked {
 		p++;
 	};
 }
+
+#ifdef HEALTH
+/*
+ * Health instrumentation. The counters live in xdata and are fed from the
+ * main loop through the banked entry points below; the "health" command
+ * prints everything in one go. All figures are raw hex, diffing two dumps
+ * gives the rates. Phase times are in system ticks (SYS_TICK_HZ = 200,
+ * 5 ms each); a phase counts as slow when it spans 2 or more ticks.
+ */
+extern __xdata uint16_t len_left;	/* httpd: bytes still to send of the current file */
+extern __xdata uint8_t entry;		/* httpd: index of the file being sent */
+
+static __xdata uint32_t health_loops;
+__xdata uint16_t health_rx_frames;
+
+static __xdata uint16_t ph_last_t;
+static __xdata uint8_t  ph_max[HEALTH_PHASES];
+static __xdata uint16_t ph_slow[HEALTH_PHASES];
+
+/* The ISR increments ticks between the two byte reads of a 16-bit load, so
+ * read until two loads agree. */
+static uint16_t ticks_lo(void)
+{
+	uint16_t a, b;
+	a = (uint16_t)ticks;
+	do {
+		b = a;
+		a = (uint16_t)ticks;
+	} while (a != b);
+	return a;
+}
+
+
+void health_loop_start(void) __banked
+{
+	health_loops++;
+	ph_last_t = ticks_lo();
+}
+
+
+void health_phase(uint8_t id) __banked
+{
+	__xdata uint16_t now = ticks_lo();
+	__xdata uint16_t d = now - ph_last_t;
+	ph_last_t = now;
+	if (d > 0xff)
+		d = 0xff;
+	if ((uint8_t)d > ph_max[id])
+		ph_max[id] = d;
+	if (d >= 2)
+		ph_slow[id]++;
+}
+
+
+/* Fill the stack area above the current frame with a pattern; the dump scans
+ * for how much of it survived. The 8051 stack grows upward, so everything
+ * above SP is free at this point. Interrupts are held off so an ISR does not
+ * push into the area mid-paint. */
+void health_stack_paint(void) __banked
+{
+	__xdata uint8_t from = SP + 4;
+	__xdata uint8_t ea = EA;
+	EA = 0;
+	for (uint8_t i = 0xff; i >= from; i--)
+		*(__idata uint8_t *)i = 0xa5;
+	EA = ea;
+}
+
+
+static void ph_line(__code const char *name, uint8_t id)
+{
+	print_string(name);
+	print_string(" max ");
+	print_byte(ph_max[id]);
+	print_string(" slow ");
+	print_short(ph_slow[id]);
+	write_char('\n');
+}
+
+
+void health_show(void) __banked
+{
+	__xdata uint8_t i;
+
+	print_string("up ");
+	reg_read_m(RTL837X_REG_SEC_COUNTER);
+	print_byte(sfr_data[0]); print_byte(sfr_data[1]);
+	print_byte(sfr_data[2]); print_byte(sfr_data[3]);
+	print_string(" ticks ");
+	print_long(ticks);
+	print_string(" loops ");
+	print_long(health_loops);
+	print_string(" rx ");
+	print_short(health_rx_frames);
+	write_char('\n');
+
+	/* Phase timing: max duration seen (ticks of 5 ms) and slow-pass count */
+	ph_line("link", HEALTH_PH_LINK);
+	ph_line("sfp ", HEALTH_PH_SFP);
+	ph_line("rx  ", HEALTH_PH_RX);
+	ph_line("tx  ", HEALTH_PH_TX);
+	ph_line("stp ", HEALTH_PH_STP);
+	ph_line("cmd ", HEALTH_PH_CMD);
+
+	/* Stack: current depth plus how much of the painted area is untouched */
+	print_string("sp ");
+	print_byte(SP);
+	print_string(" untouched ");
+	i = 0;
+	while (*(__idata uint8_t *)(0xff - i) == 0xa5 && i < 0x86)
+		i++;
+	print_byte(i);
+	write_char('\n');
+
+	/* The TCP connection slot. One on this configuration; a build with more
+	 * has to say which slot each line is, so make that a visible decision. */
+#if UIP_CONNS != 1
+#error "health: the tcp dump prints a single slot, extend it for UIP_CONNS > 1"
+#endif
+	i = 0;
+	{
+		print_string("tcp ");
+		print_string("st ");
+		print_byte(uip_conns[i].tcpstateflags);
+		print_string(" tmr ");
+		print_byte(uip_conns[i].timer);
+		print_string(" rtx ");
+		print_byte(uip_conns[i].nrtx);
+		print_string(" rto ");
+		print_byte(uip_conns[i].rto);
+		print_string(" len ");
+		print_short(uip_conns[i].len);
+		print_string(" mss ");
+		print_short(uip_conns[i].mss);
+		write_char('\n');
+		print_string("  lport ");
+		print_short(HTONS(uip_conns[i].lport));
+		print_string(" rport ");
+		print_short(HTONS(uip_conns[i].rport));
+		print_string(" rip ");
+		print_short(HTONS(uip_conns[i].ripaddr[0]));
+		write_char(' ');
+		print_short(HTONS(uip_conns[i].ripaddr[1]));
+		write_char('\n');
+	}
+
+	/* httpd transfer state and the protocol flags */
+	print_string("httpd left ");
+	print_short(len_left);
+	print_string(" entry ");
+	print_byte(entry);
+	print_string(" stp ");
+	print_byte(stp_enabled);
+	print_string(" mvlan ");
+	print_short(management_vlan);
+	write_char('\n');
+}
+#endif

cmd_parser.h

@@ -6,9 +6,36 @@
 #include "rtl837x_common.h"
 
 extern __xdata uint8_t cmd_buffer[CMD_BUF_SIZE];
-extern __xdata uint8_t cmd_available;
+extern __bit __at(0x03) cmd_available;
 extern __xdata uint8_t err_status;
 
+/* Health instrumentation, built with HEALTH=1. Without it the hooks below
+ * compile to nothing and the "health" command does not exist. */
+#ifdef HEALTH
+/* Phase ids, in main-loop order */
+#define HEALTH_PH_LINK	0
+#define HEALTH_PH_SFP	1
+#define HEALTH_PH_RX	2
+#define HEALTH_PH_TX	3
+#define HEALTH_PH_STP	4
+#define HEALTH_PH_CMD	5
+#define HEALTH_PHASES	6
+#define HEALTH_LLDP     7
+
+extern __xdata uint16_t health_rx_frames;
+#define health_rx_frame()	health_rx_frames++
+
+void health_loop_start(void) __banked;	/* once per idle() pass, resets the phase baseline */
+void health_phase(uint8_t id) __banked;	/* after each phase; accounts ticks since last checkpoint */
+void health_stack_paint(void) __banked;	/* paint the unused stack area once at boot */
+void health_show(void) __banked;	/* "health" CLI dump */
+#else
+#define health_rx_frame()
+#define health_loop_start()
+#define health_phase(id)
+#define health_stack_paint()
+#endif
+
 void cmd_tokenize(void) __banked;
 void cmd_parser(void) __banked;
 void execute_config(void) __banked;

dhcp.c

@@ -139,7 +139,6 @@ void dhcp_addopt_request_ip(void)
 	DHCP_OPT[dhcp_state.opt_ptr++] = dhcp_state.current_ip[1];
 	DHCP_OPT[dhcp_state.opt_ptr++] = dhcp_state.current_ip[2];
 	DHCP_OPT[dhcp_state.opt_ptr++] = dhcp_state.current_ip[3];
-	memcpy(&DHCP_OPT[dhcp_state.opt_ptr], uip_ethaddr.addr, 4);
 }
 
 
@@ -151,13 +150,11 @@ void dhcp_addopt_server_id(void)
 	DHCP_OPT[dhcp_state.opt_ptr++] = dhcp_state.server[1];
 	DHCP_OPT[dhcp_state.opt_ptr++] = dhcp_state.server[2];
 	DHCP_OPT[dhcp_state.opt_ptr++] = dhcp_state.server[3];
-	memcpy(&DHCP_OPT[dhcp_state.opt_ptr], uip_ethaddr.addr, 4);
 }
 
 
 void dhcp_send_discover(void)
 {
-	print_string("dhcp_send_discover called\n");
 	dhcp_prepare_request();
 
 	dhcp_state.opt_ptr = 0;
@@ -193,7 +190,6 @@ void dhcp_send_discover(void)
 
 void dhcp_send_request(void)
 {
-	print_string("dhcp_send_request called\n");
 	dhcp_prepare_request();
 
 	dhcp_state.opt_ptr = 0;
@@ -232,19 +228,21 @@ void ip_opt(__xdata uint8_t * ip)
 {
 	dhcp_state.opt_ptr++;
 	uint8_t len = DHCP_OPT[dhcp_state.opt_ptr++];
-	*ip++ = DHCP_OPT[dhcp_state.opt_ptr++];
-	*ip++ = DHCP_OPT[dhcp_state.opt_ptr++];
-	*ip++ = DHCP_OPT[dhcp_state.opt_ptr++];
-	*ip++ = DHCP_OPT[dhcp_state.opt_ptr++];
+	if (len >= 4)
+		memcpy(ip, &DHCP_OPT[dhcp_state.opt_ptr], 4);
 	 // There may be more than one IP option, such as 2 DNS servers advertised
-	dhcp_state.opt_ptr += len - 4;
+	dhcp_state.opt_ptr += len;
 }
 
 
-void long_opt(void)
+uint8_t long_opt(void)
 {
 	dhcp_state.opt_ptr++;
-	dhcp_state.opt_ptr++;
+	uint8_t len = DHCP_OPT[dhcp_state.opt_ptr++];
+	if (len < 4) {
+		dhcp_state.opt_ptr += len;
+		return 0;
+	}
 	long_value =  DHCP_OPT[dhcp_state.opt_ptr++];
 	long_value <<= 8;
 	long_value |= DHCP_OPT[dhcp_state.opt_ptr++];
@@ -252,6 +250,8 @@ void long_opt(void)
 	long_value |= DHCP_OPT[dhcp_state.opt_ptr++];
 	long_value <<= 8;
 	long_value |= DHCP_OPT[dhcp_state.opt_ptr++];
+	dhcp_state.opt_ptr += len - 4;
+	return 1;
 }
 
 
@@ -275,16 +275,16 @@ void parse_opts(void)
 			ip_opt(&dhcp_state.broadcast[0]);
 			break;
 		case DHCP_LEASE:
-			long_opt();
-			dhcp_state.lease = long_value;
+			if (long_opt())
+				dhcp_state.lease = long_value;
 			break;
 		case DHCP_REBIND:
-			long_opt();
-			dhcp_state.rebind = long_value;
+			if (long_opt())
+				dhcp_state.rebind = long_value;
 			break;
 		case DHCP_RENEWAL:
-			long_opt();
-			dhcp_state.renewal = long_value;
+			if (long_opt())
+				dhcp_state.renewal = long_value;
 			break;
 		case DHCP_END:
 			break;
@@ -376,13 +376,11 @@ void dhcp_start(void) __banked
 	*tid++ = SFR_DATA_8;
 	*tid = SFR_DATA_0;
 	dhcp_state.state = DHCP_START;
-	print_string("dhcp_start done\n");
 }
 
 
 void dhcp_stop(void) __banked
 {
-	print_string("dhcp_stop called\n");
 	uip_udp_remove(dhcp_state.conn);
 	dhcp_state.state = DHCP_OFF;
 }

doc/devices/2M-PCB23-V3_2.md

@@ -0,0 +1,40 @@
+### 2M-PCB23-V3.2
+
+## Brands
+|Brand|Type|Managed|PCB|Flash|Chip RTL|
+|---|---|---|---|---|---|
+| keepLINK | KP-9000-9XHML-X | Yes|  2M-PCB23-V3.2 | 2M (Winbond 25Q) | |
+
+The original web interface reports this board as hardware version V3.2
+(original firmware V100.9.25, January 2026).
+
+## PCB
+
+<img src="photos/2M-PCB23-V3.2-managed/2M-PCB23-V3.2-top.jpeg" width="300" />
+
+## Compared to V3.1
+
+The component placement matches [2M-PCB23-V3.1](2M-PCB23-V3_1.md): same
+positions for the flash (U8), the T7/T8/T9/T10 headers, the SFP cage and its
+LED, and the unpopulated U7/U9 footprints. Build with
+`MACHINE=KP_9000_9XHML_X_V3_2`, which uses the V3.1 machine definition and
+only differs in the reported name.
+
+## Tested
+
+Installed from the original firmware through its web interface with
+`installer/output/rtlplayground_oem_upgrade.bin`, then:
+
+- RJ45 ports link at 2.5G; LEDs: orange at 2.5G, green below
+- SFP port: module detected with vendor/model/serial and DOM readings
+  (temperature, Vcc, TX bias, TX/RX power), link up at 10G
+- factory MAC read from flash (0x1FC000)
+- reset button (GPIO48): held for more than 10 s it restores the default config
+
+## Flash access
+
+Reading the flash in-circuit with a SOIC-8 clip did not work: the chip ID
+comes back as `EF FF FF` (only the manufacturer byte is right) and reads
+return 0xff, the same as on a V3.1 board. The switch chip is powered through
+the clip and keeps driving the SPI lines. Make sure a way back is acceptable
+before installing, or hold the switch chip in reset while reading.

doc/devices/HASIVO_S1100WP_8GT_1SX_SE.md

@@ -0,0 +1,75 @@
+# Hasivo S1100WP-8GT-1SX-SE
+
+RTL8373-based 8×2.5G PoE + 1×SFP switch.
+
+### Label specifications
+
+- **Manufacturer**: Hasivo
+- **Model**: S1100WP-8GT-1SX-SE
+- **Ports**:
+  - 8 × RJ45: 10/100/1000/2500 Mbps with PoE
+  - 1 × SFP: 1G / 2.5G / 10G
+- **Power input**: DC 52V 2.5A
+- **Stock firmware defaults**: IP 192.168.0.1, user/password `admin`/`admin`
+
+### What works
+
+- All eight 2.5GBASE-T RJ45 ports at 10/100/1000/2500 Mbps (PoE is not configurable via RTLPlayground)
+- SFP port supporting 1G, 2.5G and 10G modules
+- LEDs: green (2.5G) and amber (1G/100M/10M) per copper port; combined link/act on the SFP port
+
+### Photos
+
+Front panel:
+
+<img src="photos/HASIVO_S1100WP-8GT-1SX-SE/front.jpg" width="600" />
+
+Label:
+
+<img src="photos/HASIVO_S1100WP-8GT-1SX-SE/label.jpg" width="600" />
+
+### PCB overview
+
+Top side:
+
+<img src="photos/HASIVO_S1100WP-8GT-1SX-SE/pcb_top.jpg" width="600" />
+
+Bottom side:
+
+<img src="photos/HASIVO_S1100WP-8GT-1SX-SE/pcb_bottom.jpg" width="600" />
+
+### Port layout
+
+| Logical port | Physical port | Type   |
+|--------------|---------------|--------|
+| 1-8          | 1-8           | Copper |
+| 9            | 9             | SFP    |
+
+### LED configuration
+
+Copper ports use LED SET0, the SFP port uses LED SET1.
+
+| SET  | LED0                                          | LED2                                                 |
+|------|-----------------------------------------------|------------------------------------------------------|
+| SET0 | Green — lights on 2.5G link with activity     | Amber — lights on 1G / 100M / 10M link with activity |
+| SET1 | All speeds — lights on any link with activity | —                                                    |
+
+### SFP GPIO assignments
+
+| SFP (logical 9) | pin_detect (ModAbs) | pin_los | pin_tx_disable | SerDes | I2C SDA         | I2C SCL             |
+|-----------------|---------------------|---------|----------------|--------|-----------------|---------------------|
+| SFP             | GPIO30_ACL_BIT3_EN  | GPIO37  | GPIO_NA        | SDS1   | GPIO39_I2C_SDA4 | GPIO40_I2C_SCL3_MDC1 |
+
+### Machine configuration
+
+- `reset_pin`: GPIO54_ACL_BIT2_EN
+- High LEDs (pads 27-29): mux = `LED_27 | LED_28_SYS | LED_29`, enable = `LED_28_SYS | LED_29`
+
+### PoE
+
+The 8 copper ports support PoE powered by a DC 52V 2.5A input. Power management is handled by two HS104PTI chipsets over I2C (GPIO47_I2C_SDA0, GPIO46_I2C_SCL0):
+
+* Chip 1 (I2C address 0x1A): 2.5G Ports 1–4
+* Chip 2 (I2C address 0x2A): 2.5G Ports 5–8
+
+Note: The current implementation does not yet support PoE management. Consequently, PoE currently operates in standalone mode without software control.

doc/devices/ONT-S207CW-62TS-SE.md

@@ -0,0 +1,122 @@
+# ONT-S207CW-62TS-SE / Binardat 2G06-04210GSM / Binardat 2G06-04210GS
+
+## Overview
+
+ONT-S207CW-62TS-SE, Binardat 2G06-04210GSM (managed), and Binardat 2G06-04210GS (unmanaged) are **switches with identical hardware**:
+- **CPU:** RTL8372N (confirmed via serial: "Detecting CPU: RTL8372N")
+- **Flash:** GD25Q128E (16MB)
+- **Ports:** 4x 2.5G RJ45 + 2x 10G SFP+
+- **Console:** 115200 baud (RTLPlayground firmware) / 9600 baud (stock firmware)
+
+**Note:** These devices are **RTL8372N-based** with **LAN ports mounted upside-down on the PCB**, requiring a custom configuration. The `MACHINE_ONT_S207CW_62TS_SE` definition uses a **custom configuration** with:
+- Corrected port mapping (physical ports 1-4 = RJ45, 5-6 = SFP)
+- Optimized LED sets for different port wiring (RJ45 Ports 1-2 have reversed LED wiring)
+- Custom LED mux configuration
+
+## Device Photos
+
+### Binardat 2G06-04210GSM
+
+**Front View:**
+<img src="photos/ONT-S207CW-Binardat-2G06-04210GSM/binardat-2g06-04210gsm-front.jpg" width="400" />
+
+**Back View:**
+<img src="photos/ONT-S207CW-Binardat-2G06-04210GSM/binardat-2g06-04210gsm-back.jpg" width="400" />
+
+**PCB View:**
+<img src="photos/ONT-S207CW-Binardat-2G06-04210GSM/binardat-2g06-04210gsm-pcb.jpg" width="400" />
+
+*Photos courtesy of [andreas5232](https://github.com/andreas5232) from [emesix/ONT-S207CW-62TS-SE#1](https://github.com/emesix/ONT-S207CW-62TS-SE/issues/1)*
+
+## Hardware Specification
+
+| Feature | Value |
+|---|---|
+| **CPU** | RTL8372N |
+| **Flash** | GD25Q128E (16MB) |
+| **RAM** | Integrated in RTL8372N |
+| **RJ45 Ports** | 4x 2.5GBase-T (Ports 1-4) |
+| **SFP+ Ports** | 2x 10G (Ports 5-6) |
+| **Console** | UART (115200 baud for RTLPlayground, 9600 baud for stock) |
+| **Stock Web UI IP** | 192.168.2.1 |
+| **Loader Mode IP** | 192.168.10.247 |
+
+## Port Layout
+
+```
+┌─────────────────────────────────────────────┐
+│  ┌─────┐ ┌─────┐ ┌─────┐ ┌─────┐   ┌─────┐ ┌─────┐  │
+│  │RJ45 │ │RJ45 │ │RJ45 │ │RJ45 │   │SFP+ │ │SFP+ │  │
+│  │  1  │ │  2  │ │  3  │ │  4  │   │  5  │ │  6  │  │
+│  └─────┘ └─────┘ └─────┘ └─────┘   └─────┘ └─────┘  │
+│                                                     │
+│  [System LEDs]                                      │
+└─────────────────────────────────────────────┘
+```
+
+## LED Behavior
+
+### RJ45 Ports (Physical 1-4)
+
+| LED Color | Speed |
+|---|---|
+| **Green** | 2.5G |
+| **Orange** | 1G / 100M / 10M |
+| **Off** | No link |
+
+### SFP+ Ports (Physical 5-6)
+
+| LED Color | Speed |
+|---|---|
+| **Green** | 10G |
+| **Orange** | 2.5G / 1G |
+| **Off** | No link / No SFP module |
+
+## Port to Logical Mapping
+
+Custom mapping for ONT-S207CW-62TS-SE:
+
+| Physical Port | Logical Port | Type | LED Set |
+|---|---|---|---|
+| 1 | 7 | RJ45 | 2 |
+| 2 | 6 | RJ45 | 2 |
+| 3 | 5 | RJ45 | 0 |
+| 4 | 4 | RJ45 | 0 |
+| 5 | 3 | SFP+ (SDS0) | 3 |
+| 6 | 8 | SFP+ (SDS1) | 3 |
+
+**Note:** Ports 1-2 (RJ45) have reversed LED wiring and use LED-Set 2. SFP Ports 5-6 use LED-Set 3 to account for wiring differences.
+
+## Flashing Instructions
+
+See the [README.md](../../README.md) for general flashing instructions.
+
+## Stock Firmware Information
+
+| Property | Value |
+|---|---|
+| **Default IP** | 192.168.2.1 (ONT) / 192.168.10.247 (Loader Mode) |
+| **Default Login** | admin/admin (may vary by OEM) |
+| **Console Baud** | 9600 (stock) / 115200 (RTLPlayground) |
+| **CPU String** | "RTL8372N" |
+| **Loader Mode IP** | 192.168.10.247 |
+
+## Configuration Details
+
+- **CPU:** RTL8372N
+- **SFP:** SDS0 on logical port 3 (GPIO37), SDS1 on logical port 8 (GPIO38)
+- **Port Mapping:** Physical 1-4 → Logical 7-4, Physical 5-6 → Logical 3,8
+- **LED Wiring:** RJ45 Ports 1-2 and SFP Port 6 have reversed LED pins (orange/green swapped)
+- **LED Sets:** Set 0 for RJ45 Ports 3-4, Set 1 unused, Set 2 for RJ45 Ports 1-2, Set 3 for SFP Ports 5-6
+
+## Notes
+
+- ONT-S207CW-62TS-SE, Binardat 2G06-04210GSM (managed), and Binardat 2G06-04210GS (unmanaged) are **RTL8372N-based** with **LAN ports mounted upside-down on the PCB**
+- Web UI shows correct physical port order (1-2-3-4 for RJ45, 5-6 for SFP)
+- Loader Mode always remains accessible at `192.168.10.247` for recovery
+- Serial console: 9600 baud (stock) → 115200 baud (RTLPlayground)
+
+## References
+
+- [GitHub Issue: emesix/ONT-S207CW-62TS-SE#1](https://github.com/emesix/ONT-S207CW-62TS-SE/issues/1) - Original photos and discussion
+- [PR: logicog/RTLPlayground#465](https://github.com/logicog/RTLPlayground/pull/465) - Feedback and improvements

doc/devices/SWTG018AS_A_V2_0.md

@@ -1,9 +1,10 @@
 # SWTG018AS-A V2.0
 ## Brands
-| Brand  | Type             |Managed| PCB              | Flash           | Chip RTL      |
-|--------|------------------|-------|------------------|-----------------|---------------|
-| Ampcom | SWTG018AS-A V2.0 | No    | SWTG018AS-A V2.0 | 2MB             | 8273N + 8224N |
-| Horaco | HC-SWTGW218AS-A  | Yes   | SWTG018AS-A V2.0 | 2MB(25Q16JVSIQ) | 8273N + 8224N |
+| Brand   | Type             |Managed| PCB              | Flash           | Chip RTL      |
+|---------|------------------|-------|------------------|-----------------|---------------|
+| Ampcom  | SWTG018AS-A V2.0 | No    | SWTG018AS-A V2.0 | 2MB             | 8273N + 8224N |
+| Horaco  | HC-SWTGW218AS-A  | Yes   | SWTG018AS-A V2.0 | 2MB(25Q16JVSIQ) | 8273N + 8224N |
+| GoodTop | GT-ST018M        | Yes   | SWTG018AS-A V2.0 | ?               | 8273N + 8224N |
 
 
 The following is a documentation for the unmanaged switch marked as `SWTG018AS-A V2.0`.

doc/health.md

@@ -0,0 +1,79 @@
+# The health command
+
+`health` prints a one-page snapshot of the firmware's vital signs on the
+serial console. It exists for the situations where the switch misbehaves and
+every probe from the network measures the network instead of the device: the
+dump is taken from inside, costs one command, and works while HTTP does not.
+
+```
+> health
+up 0000001f ticks 0x00001f4c loops 0x000016da rx 0x024e
+link max 01 slow 0x0000
+sfp  max 74 slow 0x0001
+rx   max 00 slow 0x0000
+tx   max 00 slow 0x0000
+stp  max 04 slow 0x0001
+cmd  max 02 slow 0x0001
+sp 80 untouched 62
+tcp st 00 tmr 00 rtx 00 rto 00 len 0x0000 mss 0x05b4
+  lport 0x0000 rport 0x0000 rip 0x0000 0x0000
+httpd left 0x0000 entry 00 stp 01 mvlan 0x0002
+```
+
+The instrumentation is not part of a default build. It costs about 1.1 kB
+of bank 2, a few bytes of xdata and seven banked calls per main-loop pass,
+which is nothing a user needs unless they are chasing a problem, so it is
+switched on at build time:
+
+```
+make MACHINE=SWTGW218AS HEALTH=1
+```
+
+Without it the hooks compile to nothing and `health` is not a command.
+
+All figures are raw hex. The counters are cumulative: take two dumps a known
+time apart and the differences give the rates.
+
+## The first line
+
+`up` is the seconds counter, `ticks` the system tick (200 per second),
+`loops` the number of main-loop passes and `rx` the frames handle_rx has
+taken off the NIC. A healthy loop completes one pass per tick, so the
+difference in `loops` tracks the difference in `ticks`; a loop that falls
+behind is being held up by one of the phases below. The `rx` rate separates
+a flooded CPU port from a stalled loop, which look identical from outside.
+
+## Phases
+
+Each line is one section of the main loop: the link poll, SFP handling,
+frame reception, TCP transmission, the STP timers and the command dispatch.
+`max` is the worst time that section has taken, in ticks of 5 ms; `slow`
+counts the passes that took two ticks or more. A misbehaving subsystem
+names itself here, which is the difference between knowing that the loop is
+slow and knowing why.
+
+A dump of its own output takes the console some milliseconds, so running
+`health` repeatedly increments the `cmd` counters by itself. That is the
+instrument observing itself, not a fault.
+
+## Stack
+
+At boot the free stack area is painted with a pattern. `sp` is the live
+stack pointer; `untouched` counts the painted bytes still intact at the top,
+which is the closest thing to a high-water mark this hardware offers. A
+shrinking `untouched` across dumps means something is reaching deeper than
+anything before it.
+
+## The TCP slot
+
+The connection table is printed whole, one slot per pair of lines: TCP
+state (3 is ESTABLISHED, 0 closed), retransmission timer and counter, bytes
+in flight, negotiated MSS, then the ports and the peer address. With a
+single slot serving the entire web interface, one glance answers the
+question every management outage starts with: who is holding it. A slot
+showing state 3 with nothing in flight and a peer that no longer answers is
+a connection whose owner went away.
+
+`httpd left` and `entry` describe the file transfer the web server believes
+it is in the middle of, and the trailing flags show whether STP is running
+and which VLAN carries management.

doc/howto_leds.md

@@ -0,0 +1,572 @@
+# LEDs HOWTO using firmware function tracing
+
+This is a tutorial to show how to figure out the LED configuration for
+unmanaged switches (on managed ones one can just print out the registers
+from the command line) without using an I2C port on the device together
+an I2C-capable microcontroller. You will only need to have a SOIC clamp
+and will have to run ghidra to do a bit of reversing.
+
+The additional advantage of this method is that it not only gives the LED
+configuration but also the full PHY configuration and SDS configuration e.g.
+in case of additional PHYs being used on the device.
+
+We will use the ZoeRax HG0402XG V1.1 as an example device.
+
+The first step is to read out the flash with a SOIC clamp.
+Save the image as
+`zoerax_hg0402xg.bin`
+
+The next step is to use a decompiler such as ghidra to identify the
+functions used to write or read registers, SDS or to the PHY.
+
+<img src="images/ghidra_open.png" width="300" />
+
+First, load the code in BANK0 into ghidra. The type of code is
+8051 default big-endian. The code starts at offset 0x0002 in the file
+and has length 0x3ffd
+
+<img src="images/ghidra_add_block.png" width="300" />
+Add BANK1 into ghidra by using File->Add to program...
+and add the code starting at 0x4000 in `zoerax_hg0402xg.bin` with length
+0xc000. Repeat for BANK2 (starts at 0x10000) and BANK3 (starts at 0x1c0000).
+They both have length 0xc000.
+
+<img src="images/ghidra_search_read_reg.png" width="300" />
+
+Now, find the read_reg function. An example of the read-register function
+is given below. Note the critical bit, namely the execution of the
+read-function of an ASIC register via an SFR: 
+```
+CODE1::4dc9 75 a0 01           MOV        SFR_EXEC_GO,#0x1
+```
+
+This sequence of bytes is very specific. Replace 0x01 with 0x03 and you have
+the regster write SFR, 0x05 reads the SerDes, 0x07 writes it. 0x09 reads
+from the PHY and 0x0b writes to it.
+
+
+```
+                             **************************************************************
+                             *                          FUNCTION                          *
+                             **************************************************************
+                             undefined reg_read()
+             undefined         <UNASSIGNED>   <RETURN>
+                             reg_read
+     CODE1::4da9 ab 07              MOV        R3,BANK0_R7                                      = ??
+     CODE1::4dab aa 06              MOV        R2,BANK0_R6                                      = ??
+     CODE1::4dad e4                 CLR        A
+     CODE1::4dae ff                 MOV        R7,A
+     CODE1::4daf fe                 MOV        R6,A
+     CODE1::4db0 fd                 MOV        R5,A
+     CODE1::4db1 fc                 MOV        R4,A
+     CODE1::4db2 90 00 c9           MOV        DPTR,#0xc9
+     CODE1::4db5 12 06 15           LCALL      FUN_CODE_0615                                    undefined FUN_CODE_0615()
+     CODE1::4db8 e4                 CLR        A
+     CODE1::4db9 ff                 MOV        R7,A
+     CODE1::4dba fe                 MOV        R6,A
+     CODE1::4dbb fd                 MOV        R5,A
+     CODE1::4dbc fc                 MOV        R4,A
+     CODE1::4dbd 90 00 c5           MOV        DPTR,#0xc5
+     CODE1::4dc0 12 06 15           LCALL      FUN_CODE_0615                                    undefined FUN_CODE_0615()
+     CODE1::4dc3 ea                 MOV        A,R2
+     CODE1::4dc4 f5 a2              MOV        SFR_A_ADDRH,A                                    = ??
+     CODE1::4dc6 eb                 MOV        A,R3
+     CODE1::4dc7 f5 a3              MOV        SFR_A_ADDRL,A                                    = ??
+     CODE1::4dc9 75 a0 01           MOV        SFR_EXEC_GO,#0x1 <<<<<<<< Executes READ REG
+                             LAB_CODE1__4dcc                                 XREF[1]:     CODE1::4dcf(j)  
+     CODE1::4dcc af a1              MOV        R7,SFR_EXEC_STATUS                               = ??
+     CODE1::4dce ef                 MOV        A,R7
+     CODE1::4dcf 70 fb              JNZ        LAB_CODE1__4dcc
+     CODE1::4dd1 af a4              MOV        R7,DAT_SFR_a4                                    = ??
+     CODE1::4dd3 fc                 MOV        R4,A
+     CODE1::4dd4 fd                 MOV        R5,A
+     CODE1::4dd5 fe                 MOV        R6,A
+     CODE1::4dd6 90 00 c9           MOV        DPTR,#0xc9
+     CODE1::4dd9 12 06 15           LCALL      FUN_CODE_0615                                    undefined FUN_CODE_0615()
+     CODE1::4ddc 90 00 c5           MOV        DPTR,#0xc5
+     CODE1::4ddf 12 05 f9           LCALL      FUN_CODE_05f9                                    undefined FUN_CODE_05f9()
+     CODE1::4de2 c0 00              PUSH       BANK0_R0
+     CODE1::4de4 90 00 c9           MOV        DPTR,#0xc9
+     CODE1::4de7 12 05 dd           LCALL      read_xmem_32_b                                   undefined read_xmem_32_b()
+     CODE1::4dea 78 18              MOV        R0,#0x18
+     CODE1::4dec 12 05 86           LCALL      FUN_CODE_0586                                    undefined FUN_CODE_0586()
+     CODE1::4def d0 00              POP        BANK0_R0
+     CODE1::4df1 12 05 48           LCALL      FUN_CODE_0548                                    undefined FUN_CODE_0548()
+     CODE1::4df4 90 00 c5           MOV        DPTR,#0xc5
+     CODE1::4df7 12 06 15           LCALL      FUN_CODE_0615                                    undefined FUN_CODE_0615()
+     CODE1::4dfa af a5              MOV        R7,DAT_SFR_a5                                    = ??
+     CODE1::4dfc e4                 CLR        A
+     CODE1::4dfd fc                 MOV        R4,A
+     CODE1::4dfe fd                 MOV        R5,A
+     CODE1::4dff fe                 MOV        R6,A
+     CODE1::4e00 90 00 c9           MOV        DPTR,#0xc9
+     CODE1::4e03 12 06 15           LCALL      FUN_CODE_0615                                    undefined FUN_CODE_0615()
+     CODE1::4e06 90 00 c5           MOV        DPTR,#0xc5
+     CODE1::4e09 12 05 f9           LCALL      FUN_CODE_05f9                                    undefined FUN_CODE_05f9()
+     CODE1::4e0c c0 00              PUSH       BANK0_R0
+     CODE1::4e0e 90 00 c9           MOV        DPTR,#0xc9
+     CODE1::4e11 12 05 dd           LCALL      read_xmem_32_b                                   undefined read_xmem_32_b()
+     CODE1::4e14 78 10              MOV        R0,#0x10
+     CODE1::4e16 12 05 86           LCALL      FUN_CODE_0586                                    undefined FUN_CODE_0586()
+     CODE1::4e19 d0 00              POP        BANK0_R0
+     CODE1::4e1b 12 05 48           LCALL      FUN_CODE_0548                                    undefined FUN_CODE_0548()
+     CODE1::4e1e 90 00 c5           MOV        DPTR,#0xc5
+     CODE1::4e21 12 06 15           LCALL      FUN_CODE_0615                                    undefined FUN_CODE_0615()
+     CODE1::4e24 af a6              MOV        R7,DAT_SFR_a6                                    = ??
+     CODE1::4e26 e4                 CLR        A
+     CODE1::4e27 fc                 MOV        R4,A
+     CODE1::4e28 fd                 MOV        R5,A
+     CODE1::4e29 fe                 MOV        R6,A
+     CODE1::4e2a 90 00 c9           MOV        DPTR,#0xc9
+     CODE1::4e2d 12 06 15           LCALL      FUN_CODE_0615                                    undefined FUN_CODE_0615()
+     CODE1::4e30 90 00 c5           MOV        DPTR,#0xc5
+     CODE1::4e33 12 05 f9           LCALL      FUN_CODE_05f9                                    undefined FUN_CODE_05f9()
+     CODE1::4e36 c0 00              PUSH       BANK0_R0
+     CODE1::4e38 90 00 c9           MOV        DPTR,#0xc9
+     CODE1::4e3b 12 05 dd           LCALL      read_xmem_32_b                                   undefined read_xmem_32_b()
+     CODE1::4e3e 78 08              MOV        R0,#0x8
+     CODE1::4e40 12 05 86           LCALL      FUN_CODE_0586                                    undefined FUN_CODE_0586()
+     CODE1::4e43 d0 00              POP        BANK0_R0
+     CODE1::4e45 12 05 48           LCALL      FUN_CODE_0548                                    undefined FUN_CODE_0548()
+     CODE1::4e48 90 00 c5           MOV        DPTR,#0xc5
+     CODE1::4e4b 12 06 15           LCALL      FUN_CODE_0615                                    undefined FUN_CODE_0615()
+     CODE1::4e4e af a7              MOV        R7,DAT_SFR_a7                                    = ??
+     CODE1::4e50 e4                 CLR        A
+     CODE1::4e51 fc                 MOV        R4,A
+     CODE1::4e52 fd                 MOV        R5,A
+     CODE1::4e53 fe                 MOV        R6,A
+     CODE1::4e54 90 00 c9           MOV        DPTR,#0xc9
+     CODE1::4e57 12 06 15           LCALL      FUN_CODE_0615                                    undefined FUN_CODE_0615()
+     CODE1::4e5a 90 00 c5           MOV        DPTR,#0xc5
+     CODE1::4e5d 12 05 dd           LCALL      read_xmem_32_b                                   undefined read_xmem_32_b()
+     CODE1::4e60 90 00 c9           MOV        DPTR,#0xc9
+     CODE1::4e63 12 05 f9           LCALL      FUN_CODE_05f9                                    undefined FUN_CODE_05f9()
+     CODE1::4e66 12 05 48           LCALL      FUN_CODE_0548                                    undefined FUN_CODE_0548()
+     CODE1::4e69 90 00 c5           MOV        DPTR,#0xc5
+     CODE1::4e6c 12 06 15           LCALL      FUN_CODE_0615                                    undefined FUN_CODE_0615()
+     CODE1::4e6f 90 00 c5           MOV        DPTR,#0xc5
+     CODE1::4e72 02 05 dd           LJMP       read_xmem_32_b                                   undefined read_xmem_32_b()
+                             -- Flow Override: CALL_RETURN (CALL_TERMINATOR)
+
+```
+
+INSERT ghidra_search_read_reg.png
+
+Identify all the read and write function to the HW of the SoC using the find
+in memory function.
+
+The next task is to adapt the intercept routines in a special assembler
+file. Don't worry, you do not need to understand assembler to do this.
+
+```
+; Assembler file to intercept register writes/reads and PHY writes/reads
+; assemble with as31
+; Compile with
+; as31 -Fbyte -Orwintercept_zoerax_hg0402xg.hex rwintercept_zoerax_hg0402xg.asm
+; ./injector zoerax_hg0402xg.bin RTLPlayground/rwintercept_zoerax_hg0402xg.hex zoerax_hg0402xg_patched.bin
+; Start at 0x3b00, where there is always some space in BANK 0
+	.equ	valptr, 0x199
+
+
+	.equ	SFR_DATA_0, 0xa7
+	.equ	SFR_DATA_8, 0xa6
+	.equ	SFR_DATA_16, 0xa5
+	.equ	SFR_DATA_24, 0xa4
+
+; Intercept Register Write
+	.org 0x4d62
+	lcall	reg_write
+	nop
+
+; Intercept Register Read
+	.org 0x4dad
+	lcall	reg_read_head
+	.org 0x4e6f
+	lcall	reg_read_tail
+
+; Intercept PHY write
+	.org 0x522c
+	lcall	phy_write
+
+; Intercept PHY read
+	.org 0x526f
+	lcall	phy_read_head
+	.org 0x5295
+	ljmp	phy_read_tail
+
+; Intercept SDS write
+	.org 0x503c
+	lcall	sds_write
+	nop
+
+; Intercept SDS read
+	.org 0x5061
+	lcall	sds_read_head
+	nop
+	.org 0x507b
+	ljmp	sds_read_tail
+
+;
+; BEGIN actual code at unused end of BANK0
+;
+	.org 0x3b00
+
+;
+; print the address of a register write. The address is in R6/R7. A and r4 can be scratched
+;
+reg_write:	
+	mov	a, #'R'
+	acall	putc
+
+	mov	a, r6
+	acall	wbyte
+
+	mov	a, r7
+	acall	wbyte
+
+	mov	a, #'-'
+	acall	putc
+
+	mov	dptr, #valptr
+	movx	a, @dptr
+	acall	wbyte
+	mov	dptr, #valptr + 1
+	movx	a, @dptr
+	acall	wbyte
+	mov	dptr, #valptr + 2
+	movx	a, @dptr
+	acall	wbyte
+	mov	dptr, #valptr + 3
+	movx	a, @dptr
+	acall	wbyte
+
+	mov	a, #' '
+	acall	putc
+
+	mov	a, r7
+	mov	r5, a
+	mov	a, r6
+	mov	r4, a
+	ret
+[...]
+```
+
+The full assembler file can be found here: XXXXXXXXXX
+
+
+Once you have assembled the code, inject the bytes into the existing image,
+creating a patched version:
+```
+$ as31 -Fbyte -Orwintercept_zoerax_hg0402xg.hex rwintercept_zoerax_hg0402xg.asm
+Begin Pass #1
+Begin Pass #2
+./injector zoerax_hg0402xg.bin rwintercept_zoerax_hg0402xg.hex zoerax_hg0402xg_patched.bin
+Input file size: 1048576
+Bytes read:: 1048576
+Patched 417 bytes.
+```
+
+Now flash `zoerax_hg0402xg_patched.bin` onto device.
+
+Connect a serial adapter and plug in power. You will see:
+
+```
+$ picocom -b 9600 /dev/ttyUSB0 
+picocom v3.1
+
+port is        : /dev/ttyUSB0
+flowcontrol    : none
+baudrate is    : 9600
+parity is      : none
+databits are   : 8
+stopbits are   : 1
+escape is      : C-a
+local echo is  : no
+noinit is      : no
+noreset is     : no
+hangup is      : no
+nolock is      : no
+send_cmd is    : sz -vv
+receive_cmd is : rz -vv -E
+imap is        : 
+omap is        : 
+emap is        : crcrlf,delbs,
+logfile is     : none
+initstring     : none
+exit_after is  : not set
+exit is        : no
+
+Type [C-a] [C-h] to see available commands
+Terminal ready
+[The printout only starts once the serial peripherial has been set up. Initially its timing is off:]
+�.Ӛ�҂���������30-00005555 r6330:00005555 R6330-00005515 [RTL837X_REG_SMI_MAC_TYPE]
+[RTL837X_REG_SMI_PORT_POLLING: ]
+r6334:00000000 R6334-000000f0
+r6454:00000000 R6454-00007000
+
+[Read SoC-Revision]
+r000c:00200000 R000c-002a0000 r000c:202a6818 r000c:202a6818 R000c-20206818
+p001e.000d:ffff R02f8-0000ffff R02f4-0000fffa P000001.1e00000d:fffa p001e.000d:ffff p001e.000d:ffff
+R02f8-0000ffff R02f4-0000fff0 P000001.1e00000d:fff0
+
+[RTL837X_REG_LED_MODE being configured:]
+r6520:0021fdb0 R6520-0021e7b0 r6520:0021e7b0 R6520-0021e6b0
+
+[RLDP Leds configured via RTL837X_REG_LED_RLDP_X:]
+r65f8:00000018 R65f8-0000001b R65fc-fffff000 r6600:00000000 R6600-0000000f
+
+[RTL837X_REG_LED_GLB_IO_EN: ]
+r65dc:5fffff00 R65dc-7fffff00 r65dc:7fffff00 R65dc-77ffff00
+
+[RTL837X_PIN_MUX_0, makes serial go out of sync:]
+r7f8c:30000000 R7f8c-30000000 r7f8c:300��.Ӛ�҂���������30-00005555
+
+r6330:00005555 R6330-00005515 r6334:00000000 R6334-000000f0
+
+r6454:00000000 R6454-00007000
+
+[Read SoC-Revision (again)]
+r000c:00200000 R000c-002a0000 r000c:202a6818 r000c:202a6818 R000c-20206818
+p001e.000d:ffff R02f8-0000ffff R02f4-0000fffa P000001.1e00000d:fffa p001e.000d:ffff p001e.000d:ffff
+R02f8-0000ffff R02f4-0000fff0
+P000001.1e00000d:fff0
+
+#### LED configuration ########
+[RTL837X_REG_LED_MODE being configured (final):]
+r6520:0021fdb0 R6520-0021e7b0 r6520:0021e7b0 R6520-0021e6b0
+
+[More RTL837X_REG_LED_RLDP]
+r65f8:00000018 R65f8-0000001b R65fc-fffff000 r6600:00000000 R6600-0000000f
+
+[RTL837X_REG_LED_GLB_IO_EN]
+r65dc:5fffff00 R65dc-7fffff00 r65dc:7fffff00 R65dc-77ffff00
+
+[RTL837X_PIN_MUX_0
+r7f8c:30000000 R7f8c-30000000 r7f8c:30000000 R7f8c-38000000
+
+[RTL837X_LED_PORT_SET_SEL]
+r654c:00000000 R654c-00010000
+
+[RTL837X_REG_LED1_0_SET0]
+R6548-00000141
+
+[RTL837X_REG_LED3_2_SET0]
+r6544:01411000 R6544-01410174
+
+[RTL837X_REG_LED1_0_SET1]
+r6540:00440070 R6540-0044017f
+
+[RTL837X_REG_LED3_0_SET1]
+r6528:00000000 R6528-000f0000
+
+[SDS 0 being configure:]
+r7b20:00000bff R7b20-000003ff r7b20:000003ff R7b20-000003fa r7b20:000003fa R7b20-000003fa
+Q002110:4480 Q002113:0400 Q002118:6d02 Q00211b:424e Q00211d:0002 Q00361c:1390 
+Q003614:003f Q003610:0200 Q002e04:0080 Q002e06:0408 Q002e07:020d Q002e09:0601 
+Q002e0b:222c Q002e0c:a217 Q002e0d:fe40 Q002e15:f5c1 Q002e16:0443 Q002e1d:abb0 
+Q000612:5078 Q000706:9401 Q000708:9401 Q00070a:9401 Q00070c:9401 Q001f0b:0003 
+Q000603:c45c Q00061f:2100 q001f0b:0003 Q001f0b:000f q002000:0000 Q002000:0030 
+q002000:0030 Q002000:0010 q002000:0010 Q002000:0050 q002000:0050 Q002000:00d0 
+q002000:00d0 Q002000:0cd0 q002000:0cd0 Q002000:04d0 q002000:04d0 Q002000:04d0 
+q002000:04d0 Q002000:0cd0 q002000:0cd0 Q002000:00d0 q002000:00d0 Q002000:00d0 
+q002000:00d0 Q002000:0050 q002000:0050 Q002000:0010 q002000:0010 Q002000:0010 
+q002000:0010 Q002000:0030 q002000:0030 Q002000:0000 q001f00:0000 Q001f00:000b 
+q001f00:000b Q001f00:0000
+
+[SDS 1 being configured]
+r7b20:000003fa R7b20-000003fa r7b20:000003fa R7b20-0000035a r7b20:0000035a R7b20-0000035a
+Q012110:4480 Q012113:0400 Q012118:6d02 Q01211b:424e Q01211d:0002 Q01361c:1390 
+Q013614:003f Q013610:0200 Q012e04:0080 Q012e06:0408 Q012e07:020d Q012e09:0601 
+Q012e0b:222c Q012e0c:a217 Q012e0d:fe40 Q012e15:f5c1 Q012e16:0443 Q012e1d:abb0 
+Q010612:5078 Q010706:9401 Q010708:9401 Q01070a:9401 Q01070c:9401 Q011f0b:0003 
+Q010603:c45c Q01061f:2100 q011f0b:0003 Q011f0b:000f q012000:0000 Q012000:0030 
+q012000:0030 Q012000:0010 q012000:0010 Q012000:0050 q012000:0050 Q012000:00d0 
+q012000:00d0 Q012000:0cd0 q012000:0cd0 Q012000:04d0 q012000:04d0 Q012000:04d0 
+q012000:04d0 Q012000:0cd0 q012000:0cd0 Q012000:00d0 q012000:00d0 Q012000:00d0 
+q012000:00d0 Q012000:0050 q012000:0050 Q012000:0010 q012000:0010 Q012000:0010 
+q012000:0010 Q012000:0030 q012000:0030 Q012000:0000 q011f00:0000 Q011f00:000b 
+q011f00:000b Q011f00:0000 q012100:4902 Q012100:4906 q013605:0000 Q013605:4000 
+Q011f02:001f q011f15:0096 q002100:4902 Q002100:4906 q003605:0000 Q003605:4000 
+Q001f02:001f q001f15:00a6
+
+r0a90:000000f3 R0a90-000000fc P0000f0.1f00a610:2858 r5fd4:0002914a 
+R5fd4-001a914a r1538:00000e33 R1538-00000e37 r1538:00000e37 R1538-00000e37 
+r1538:00000e37 R1538-00000f37 r1638:00000e33 R1638-00000e37 r1638:00000e37 
+R1638-00000e37 r1638:00000e37 R1638-00000f37 r1738:00000e33 R1738-00000e37 
+r1738:00000e37 R1738-00000e37 r1738:00000e37 R1738-00000f37 r1838:00000e33 
+R1838-00000e37 r1838:00000e37 R1838-00000e37 r1838:00000e37 R1838-00000f37 
+r1938:00000e33 R1938-00000e37 r1938:00000e37 R1938-00000e37 r1938:00000e37 
+R1938-00000f37 r1a38:00000e33 R1a38-00000e37 r1a38:00000e37 R1a38-00000e37 
+r1a38:00000e37 R1a38-00000f37 r0b7c:000000d8 R0b7c-000000f8 R7124-00001050 
+R7128-00001050 R712c-00001050 R7130-00001050 R7134-00001050 R7138-00001050 
+R713c-00001050 R7140-00001050 R7144-00001050 R7148-00001050 r6040:00000030 
+R6040-00000031 p041f.a436:8195 P000010.1f00a436:0005 p041f.a438:02d4 
+P000010.1f00a436:801e p041f.a438:0000 p041f.b820:0000 P000010.1f00b820:0010 
+p041f.b800:00c0 p041f.a436:801e P000010.1f00a436:8023 p041f.a438:0000 
+P000010.1f00a438:1802 p041f.a436:8025 
+
+[PHY with ID 5 being patched] P000010.1f00a436:b82e p041f.a438:0000 
+P000010.1f00a438:0001 p041f.b820:0010 P000010.1f00b820:0090 
+P000010.1f00a436:a016 P000010.1f00a438:0000 P000010.1f00a436:a012 
+P000010.1f00a438:0000 P000010.1f00a436:a014 P000010.1f00a438:1800 
+P000010.1f00a438:8010 P000010.1f00a438:1800 P000010.1f00a438:8013 
+P000010.1f00a438:1800 P000010.1f00a438:8026 P000010.1f00a438:1800 
+P000010.1f00a438:802a P000010.1f00a438:1800 P000010.1f00a438:802e 
+P000010.1f00a438:1800 P000010.1f00a438:802e P000010.1f00a438:1800 
+P000010.1f00a438:802e P000010.1f00a438:1800 P000010.1f00a438:802e 
+...
+```
+Where:
+```
+r: read-reg
+R: write-reg
+q: read SDS
+Q: write SDS
+p: read PHY
+P: write SDS
+```
+
+The LED configuration has been marked above. We now write exactly those registers
+into the registers of `rtlplayground.c` on startup:
+
+```
+[...]
+	set_sys_led_state(SYS_LED_ON);
+
+	// [RTL837X_REG_LED_MODE being configured (final):]
+	// r6520:0021fdb0 R6520-0021e7b0 r6520:0021e7b0 R6520-0021e6b0
+	REG_SET(RTL837X_REG_LED_MODE, 0x0021e6b0);
+
+	// [More RTL837X_REG_LED_RLDP]
+	// r65f8:00000018 R65f8-0000001b R65fc-fffff000 r6600:00000000 R6600-0000000f
+	REG_SET(0x65f8, 0x0000001b);
+	REG_SET(0x65fc, 0xfffff000);
+	REG_SET(0x6600, 0x0000000f);
+
+	// [RTL837X_REG_LED_GLB_IO_EN]
+	// r65dc:5fffff00 R65dc-7fffff00 r65dc:7fffff00 R65dc-77ffff00
+	REG_SET(0x65dc, 0x77ffff00);
+
+	// [RTL837X_PIN_MUX_0
+	// r7f8c:30000000 R7f8c-30000000 r7f8c:30000000 R7f8c-38000000
+	REG_SET(0x7f8c, 0x38000000);
+
+	// [RTL837X_LED_PORT_SET_SEL]
+	// r654c:00000000 R654c-00010000
+	REG_SET(0x654c, 0x00010040);
+
+	// [RTL837X_REG_LED1_0_SET0]
+	// R6548-00000141
+	REG_SET(0x6548, 0x00000141);
+
+	// [RTL837X_REG_LED3_2_SET0]
+	// r6544:01411000 R6544-01410174
+	REG_SET(0x6544, 0x01410174);
+
+	// [RTL837X_REG_LED1_0_SET1]
+	// r6540:00440070 R6540-0044017f
+	REG_SET(0x6540, 0x0044017f);
+
+	// [RTL837X_REG_LED3_0_SET1]
+	// r6528:00000000 R6528-000f0000
+	REG_SET(0x6528, 0x000f0000);
+
+	cmd_editor_init();
+[...]
+```
+
+Create an initial configuraiton for your device by copying over an existing one
+for the same device type, i.e. same port-configuraiton and same SoC,
+give it a new name. Make sure that the led_mux_custom and led_mux fields are not
+used, because our device does not customize the LED muxes.
+
+Compile and flash onto your device.
+
+Now, boot the switch and issue the `leds`command, which will print out:
+```
+RTL837X_PIN_MUX_0: 0x38000000
+RTL837X_REG_LED_GLB_IO_EN: 0x77ffff00
+RTL837X_REG_LED1_0_SET0: 0x00000141
+RTL837X_REG_LED3_2_SET0: 0x01410174
+RTL837X_REG_LED1_0_SET1: 0x0044017f
+RTL837X_REG_LED3_2_SET1: 0x18000040
+RTL837X_REG_LED1_0_SET2: 0x00000000
+RTL837X_REG_LED3_2_SET2: 0x00000000
+RTL837X_REG_LED1_0_SET3: 0x00000000
+RTL837X_REG_LED3_2_SET3: 0x00000000
+RTL837X_REG_LED3_0_SET1: 0x000f0000
+RTL837X_REG_LED3_0_SET3: 0x00000000
+RTL837X_LED_PORT_SET_SEL: 0x00010040
+RTL837X_REG_LED_GLB_MUX_1: 0x3fffffff
+RTL837X_REG_LED_GLB_MUX_2: 0x0c3fffff
+RTL837X_REG_LED_GLB_MUX_3: 0x1245038d
+RTL837X_REG_LED_GLB_MUX_4: 0x19616554
+RTL837X_REG_LED_GLB_MUX_5: 0x2079d71a
+RTL837X_REG_LED_GLB_MUX_6: 0x000238a1
+RTL837X_REG_LED_GLB_ACTIVE: 0x3ffbedff
+RTL837X_REG_LED_MODE: 0x0021e6b0
+LED pad Configuration:
+00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 19 1a 1b 
+3f 3f 3f 3f 3f 3f 3f 3f 0f 0c 0d 0e 10 11 12 14 15 16 18 19 1a 1c 1d 1e 20 21 22 23 
+LED-set Configuration:
+LED-ID          0               1               2               3
+SET 0:     000141          000000          000174          000141
+SET 1:     0f017f          000044          000040          001800
+SET 2:     000000          000000          000000          000000
+SET 3:     000000          000000          000000          000000
+Port 3: SET 1: ( 2G5 TWO_1G 1G 500M 100M 10M LINK ACT 10G TWO_5G 5G TWO_2G5), ( 1G LINK), ( LINK), ( COL DUPLEX), 
+Port 4: SET 0: ( 2G5 LINK ACT), (), ( 1G 100M 10M LINK ACT), ( 2G5 LINK ACT), 
+Port 5: SET 0: ( 2G5 LINK ACT), (), ( 1G 100M 10M LINK ACT), ( 2G5 LINK ACT), 
+Port 6: SET 0: ( 2G5 LINK ACT), (), ( 1G 100M 10M LINK ACT), ( 2G5 LINK ACT), 
+Port 7: SET 0: ( 2G5 LINK ACT), (), ( 1G 100M 10M LINK ACT), ( 2G5 LINK ACT), 
+Port 8: SET 1: ( 2G5 TWO_1G 1G 500M 100M 10M LINK ACT 10G TWO_5G 5G TWO_2G5), ( 1G LINK), ( LINK), ( COL DUPLEX), 
+
+```
+Together with the GPIO information, this will give you the following machine configuration:
+```
+_code const struct machine machine = {
+	.machine_name = "ZOERAX HG0402XG",
+	.isRTL8373 = 0,
+	.min_port = 3,
+	.max_port = 8,
+	.n_sfp = 2,
+	.log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
+	.phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
+	.is_sfp = {0, 0, 0, 1, 0, 0, 0, 0, 2},
+	// Left SFP port (5)
+	.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
+	.sfp_port[0].pin_los = GPIO_NA,
+	.sfp_port[0].pin_tx_disable = GPIO_NA,
+	.sfp_port[0].sds = 1,
+	.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
+	// Right SFP port (6)
+	.sfp_port[1].pin_detect = GPIO50_I2C_SCL2_UART1_TX,
+	.sfp_port[1].pin_los = GPIO_NA,
+	.sfp_port[1].pin_tx_disable = GPIO_NA,
+	.sfp_port[1].sds = 0,
+	.sfp_port[1].i2c = I2CBUS( GPIO41_I2C_SDA3_MDIO1, GPIO40_I2C_SCL3_MDC1 ),
+	.reset_pin = GPIO_NA,
+	.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28_SYS | LED_29 },
+	.port_led_set = { 0, 0, 0, 1, 0, 0, 0, 0, 1},
+	/* On Ethernet: Left led is orange, right green
+	 * 100M and 1G give right led green with activity
+	 * 2.5GBit adds solid left orange LED
+	 * LEDs for the SFP-ports are the same as for the Ethernet ports
+	*/
+	.led_sets = { { LEDS_2G5 | LEDS_LINK | LEDS_ACT,
+			0,
+			LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
+			LEDS_2G5 | LEDS_LINK | LEDS_ACT
+		      },
+		      { LEDS_2G5 | LEDS_TWO_PAIR_1G | LEDS_1G | LEDS_500M | LEDS_100M | LEDS_10M |
+			LEDS_LINK | LEDS_ACT | LEDS_10G | LEDS_TWO_PAIR_5G | LEDS_5G | LEDS_TWO_PAIR_2G5,
+			LEDS_1G | LEDS_LINK,
+			LEDS_LINK,
+			LEDS_COL | LEDS_DUPLEX
+		      } 
+		    }
+		    
+};
+```
+
+

doc/igmp.md

@@ -69,7 +69,7 @@ The code currently provides the following functions:
 void igmp_setup(void) __banked;
 void igmp_enable(void) __banked;
 void igmp_router_port_set(uint16_t pmask) __banked;
-void igmp_packet_handler(void) __banked;
+uint8_t igmp_packet_handler(void) __banked;
 void igmp_show(void) __banked;
 ```c
 `igmp_setup()` is called at boot-time and configures flooding of all IP-MC packets by
@@ -80,7 +80,11 @@ of IP-MC packets to be limited to only subscribed ports.
 
 `igmp_router_port_set()`configures forwarding ports for IGMP messages.
 
-`igmp_packet_handler()` implements handling of trapped IGMP packets by the CPU.
+`igmp_packet_handler()` implements handling of trapped IGMP packets by the CPU. It is called
+for frames to 01:00:5e:xx:xx:xx and returns 0 when the frame is not a trapped IGMP packet,
+so that it is passed on to the IP stack. IGMPv1/v2 reports (0x12, 0x16) join the group given
+in the IGMP header, IGMPv2 leaves (0x17) leave it, IGMPv3 reports use the first group record
+(type 4 joins, type 3 leaves). Trapped IGMP frames arrive without a VLAN tag.
 
 `igmp_show()` prints out the IGMP configuration on the CLI.
 

doc/storm_control.md

@@ -0,0 +1,54 @@
+# Storm Control
+Storm control limits the rate at which a port admits broadcast, multicast,
+unknown unicast and unknown multicast frames. Frames of a type above its limit
+are dropped at ingress, so a loop or a misbehaving host cannot flood the rest
+of the network through that port. Known unicast traffic is not affected.
+
+## Commands
+```
+storm <port> bcast|mcast|ucast|umcast <rate> pps
+storm <port> bcast|mcast|ucast|umcast <rate> kbps
+storm <port> bcast|mcast|ucast|umcast off
+storm
+```
+`ucast` is unicast to a MAC address the switch has not learned yet, and
+`umcast` is multicast without an entry in the address table. Multicast groups
+get their entries from IGMP snooping, so without `igmp on` all multicast is
+unknown and only the `umcast` limit applies to it; `mcast` covers the groups
+IGMP has learned. A limit in
+packets per second goes from 1 to 1048575, a limit in kbit/s from 1 to
+10000000. `storm` without arguments prints the limits of every port. The
+limits are kept in the configuration like any other setting, and the Bandwidth
+page of the web interface has a Storm control card to set them.
+
+## Registers
+Each port and type has an enable bit and a meter index, and each limit uses
+one of the 64 shared meters of the switch. RTLPlayground gives every port and
+type its own meter, index `24 + port * 4 + type`, so one port's storm does not
+eat into the limit of another. Storm control uses meters 24 to 63 and leaves
+0 to 23 to the ACL. The limit of a meter is in `RTL837X_METER_RATE + 4 *
+meter`, and bit `meter % 32` of `RTL837X_METER_MODE + 4 * (meter / 32)`
+selects pps instead of kbit/s.
+```
+#define RTL837X_STORM_CTRL		0x54e4	/* + 4 * type, bit = port */
+#define RTL837X_STORM_MIDX		0x54f4	/* + 8 * type + 4 * (port / 5), 6 bits per port */
+#define RTL837X_METER_RATE		0x5cf0	/* + 4 * meter, 24 bits, kbit/s or pps */
+#define RTL837X_METER_MODE		0x5ef0	/* + 4 * (meter / 32), bit set = pps */
+```
+In kbit/s mode one step of the rate is 1 kbit/s. Measured with 100 and 1000 byte
+frames, the meter counts a frame with its FCS, but without preamble and
+interframe gap. Every meter has a bit that adds them, in `0x5f08 + 4 * (meter
+/ 32)`, which storm control leaves cleared. `IGBW_INC_IFG` and `EGBW_INC_IFG`
+are the matching bits of the bandwidth control.
+
+An ingress bandwidth limit on the same port works on the same arriving frames
+as the storm limit rather than after it, and the two together pass far less
+than either one: a 1 Mbit/s `umcast` limit with a 10 Mbit/s ingress limit let
+0.12 to 0.16 Mbit/s of a 1.4 Gbit/s stream through, where each alone passed
+1.17 and 10.2 Mbit/s.
+
+The type is 0 for broadcast, 1 for multicast, 2 for unknown unicast and 3 for
+unknown multicast. The burst size of a meter (0x5df0 + 4 * meter) counts packets
+in pps mode; its default of 0x2000 lets 8192 frames through before a pps limit
+bites, so a pps limit sets the burst to one second of traffic. A kbit/s limit
+puts back the default.

doc/supported_devices.md

@@ -7,6 +7,8 @@ The following devices have been tested and are fully working:
 | Davuaz   | Da-K6501W       | No      | [PCB-K0501W-V2.0](devices/K0501W_V2_0.md)                                 |       | 5 + 1 |
 | FOXNEO   | FNS-1200P       | No      | [PCB-K0402W-U13-V2.0](devices/FNS-1200P.md)                               | 2M    | 4 + 2 |
 | Goalake  | IG108           | No      | [PB-2132](devices/PB-2132.md)                                             | 4M    | 8 + 1 |
+| GoodTop  | GT-ST018M       | Yes     | [SWTG018AS-A V2.0](devices/SWTG018AS_A_V2_0.md)                           | ?     | 8 + 1 |
+| Hasivo   | S1100WP_8GT_1SX_SE | Yes  | [S1100WP_8GT_1SX_SE-V1.05](devices/HASIVO_S1100WP_8GT_1SX_SE.md)          | 2M    | 8 + 1 |
 | Hisource | Hi-K0402WS      | No      | [PCB-K0402WS-V3.0](devices/PCB-K0402WS-V3.0.md)                           |       | 4 + 2 |
 | Hisource | Hi-K0402WS      | No      | [PCB-K0402WS-V2.0](devices/PCB-K0402WS-V2.0.md)                           | 2M    | 4 + 2 |
 | Hisource | Hi-K0801WS      | No      | [PCB-KO801W-V2.0](devices/HI-K0801WS.md)                                  |       | 8 + 1 |
@@ -20,12 +22,15 @@ The following devices have been tested and are fully working:
 | Keeplink | KP-9000-6XH-X2 / KP-9000-6XHML-X2 | No/Yes | [2M-PCB43-V1.2 / V2.1](devices/KP-9000-6XH-X2.md) |       | 4 + 2 |
 | keepLINK | KP-9000-9XHML-X | Yes     | [2M-PCB23-V2.2](devices/2M-PCB23-V2_2.md)                                 | 2M    | 8 + 1 |
 | keepLINK | KP-9000-9XHML-X | Yes     | [2M-PCB23-V3.1](devices/2M-PCB23-V3_1.md)                                 | 2M    | 8 + 1 |
+| keepLINK | KP-9000-9XHML-X | Yes     | [2M-PCB23-V3.2](devices/2M-PCB23-V3_2.md)                                 | 2M    | 8 + 1 |
 | LIANGUO  | SWTG024AS       | No      | [SWTG024AS-v2.0-17452](devices/SWTG024AS.md)                              | 0.5M  | 4 + 2 |
 | Lianguo  | ZX-SWTGW215AS   | Yes     | [PCB-SWTG115AS-V2.0 / PCB-SWTG115AS-V2.1](devices/SWTGW215AS.md)          | 2M    | 5 + 1 |
 | Lianguo  | HYWS-SGT0108S   | No      | [2G5F_20G_V1.01](devices/HYWS-SGT0108S.md)                                | 0.5M  | 8 + 1 |
 | Mokerlink| 2G040210GSM     | Yes     | [2M-PCB43-V1.1](devices/2M-PCB43-V1.1.md)                                 |       | 4 + 2 |
 | Mokerlink| ZX-SWTGW218AS   | Yes     | [SWTG118AS-V2.0-16029](devices/SWTGW218AS.md)                             | 2M    | 8 + 1 |
 | MokerLink| POE-2G080110GS  | No      | [2M-PCB51-ML-V1.1](devices/2M-PCB51-ML-V1_1.md)                           | 4M    | 8 + 1 |
+| Binardat | 2G06-04210GSM    | No      | [PCB-SWTG024AS-A-2.0.1](devices/ONT-S207CW-62TS-SE.md)                 | 0.5M  | 4 + 2 |
+| ONT      | ONT-S207CW-62TS-SE | No   | [PCB-SWTG024AS-A-2.0.1](devices/ONT-S207CW-62TS-SE.md)                 | 0.5M  | 4 + 2 |
 | Netcore  | GS9             | No      | [PB-2132](devices/PB-2132.md)                                             | 4M    | 8 + 1 |
 | Ruiying  | RY-4GT-2SX      | No      | [FG-4GT-2SX_V2.0](devices/FG-4GT-2SX_V2.0.md)                             | 4M    | 4 + 2 |
 | Ruiying  | RY-8GT-1SX      | No      | [FG-8GT-1SX](devices/FG-8GT-1SX.md)                                       | 1M    | 8 + 1 |

html/app.js

@@ -2,8 +2,8 @@
 var LANG={
 en:{
 nav_dash:"Dashboard",nav_ports:"Ports",nav_stp:"Spanning tree",nav_stats:"Statistics",
-nav_vlan:"VLANs",nav_l2:"MAC table",nav_mirror:"Mirroring",nav_lag:"LAG",nav_eee:"EEE",
-nav_bw:"Bandwidth",nav_system:"System",nav_fw:"Firmware",
+nav_vlan:"VLANs",nav_l2:"MAC table",nav_mirror:"Mirroring",nav_isolate:"Isolation",nav_lag:"LAG",nav_eee:"EEE",
+nav_bw:"Bandwidth",nav_system:"System",nav_fw:"Firmware",nav_lldp:"LLDP",
 hdr_dirty:"unsaved changes",hdr_dirty_t:"Running config differs from startup config",
 hdr_save:"Save to flash",hdr_save_t:"Persist running configuration to flash",
 th_auto:"System",th_auto_sel:"System (Selenized)",sy_display:"Display",sy_theme:"Theme",sy_display_note:"Stored in this browser only.",th_light:"Light",th_dark:"Dark",
@@ -15,7 +15,7 @@ c_full:"full",c_half:"half",c_devices:"devices",c_yes:"yes",c_no:"no",
 d_ports:"Ports",d_ports_h:"click a port for details",d_system:"System",d_traffic:"Traffic",
 d_traffic_h:"packets/s, live",d_txpps:"TX pps",d_rxpps:"RX pps",d_txbad:"TX bad",d_rxbad:"RX bad",
 i_host:"Hostname",i_ip:"IP address",i_mask:"Netmask",i_gw:"Gateway",i_mac:"MAC",i_fw:"Firmware",
-i_built:"Built",i_hw:"Hardware",i_flash:"Flash",i_syslog:"Syslog",
+i_built:"Built",i_hw:"Hardware",i_temp:"Temperature",i_flash:"Flash",i_syslog:"Syslog",
 p_state:"State",p_disabled:"disabled",p_up:"up",p_txgb:"TX good / bad",p_rxgb:"RX good / bad",
 p_pkts:"pkts",p_module:"Module",p_temp:"Temperature",p_vcc:"Vcc",p_txbias:"TX bias",p_txpower:"TX power",
 p_rxpower:"RX power",p_txfault:"TX fault",p_txdis:"TX disabled",p_rxlos:"RX LOS",p_adv:"Advertising",
@@ -40,6 +40,7 @@ stp_en_q:"Enable spanning tree?",
 stp_en_d:"Ports start blocked and take up to twice the forward delay to reach forwarding; edge ports recover immediately.",
 stp_dis_q:"Disable spanning tree?",stp_dis_d:"All ports go straight to forwarding; loop protection is lost.",
 stp_cost_err:"Path cost must be 0-200000000",
+lldp_enabled: "LLDP Enabled",lldp_title:"Service Status",lldp_portname:"Name",lldp_enable:"Send Frames",
 st_title:"Port statistics",st_h:"totals since boot",st_txg:"TX good",st_txb:"TX bad",st_rxg:"RX good",
 st_rxb:"RX bad",st_details:"Details",st_counters:"MIB counters",st_nonzero:"non-zero only",
 st_autoref:"auto-refresh",st_counter:"Counter",st_value:"Value",st_fail:"failed to load counters",
@@ -62,6 +63,9 @@ l2_learned:"learned",l2_loading:"loading...",l2_failed:"load failed",l2_entries:
 l2_del_t:"Delete entry",l2_flush_q:"Flush all learned MAC entries?",
 m_title:"Port mirroring",m_active:"active",m_monitor:"Monitor port",m_mirror:"Mirror",m_both:"Both",
 m_note:"Both = mirror RX and TX of the port to the monitor port.",m_none:"Select at least one mirrored port",
+iso_title:"Port isolation",iso_from:"From port",iso_to:"To port",iso_all:"Allow all",
+iso_intro:"A frame entering a port may only leave through the ports ticked in its row. Isolation is decided before forwarding, so a port that is not ticked is unreachable directly, whatever the address table says.",
+iso_legend:"The cell of the port itself is always allowed. A port number in red marks a port that is not fully open.",
 lag_hash:"Hash:",lag_note:"A LAG needs at least one member to be saved in the startup config; applying an empty group clears it.",
 lag_clear_q:"Clear LAG {n}?",lag_clear_d:"All member ports return to normal operation.",
 e_title:"Energy Efficient Ethernet",e_adv:"Advertised",e_lp:"Link partner",e_active:"Active",e_enable:"Enable",
@@ -70,8 +74,12 @@ e_idle:"idle",e_na:"n/a",
 bw_title:"Bandwidth limits",bw_h:"Mbit/s, 0.016-10000",bw_in:"Ingress limit",bw_out:"Egress limit",
 bw_exceed:"When exceeded",bw_fc:"Flow control",bw_drop:"Drop",
 bw_in_err:"Ingress limit must be 0.016-10000 Mbit/s",bw_out_err:"Egress limit must be 0.016-10000 Mbit/s",
+sc_title:"Storm control",sc_h:"per port and traffic type, empty = off",sc_bcast:"Broadcast",sc_mcast:"Multicast",
+sc_ucast:"Unknown unicast",sc_umcast:"Unknown multicast",sc_err:"Storm limit must be 1-1048575 pps or 1-10000000 kbit/s",
+sc_note:"Frames of a type above its limit are dropped where they enter the switch.",
 sy_network:"Network",sy_dhcp:"Use DHCP",sy_dhcp_t:"Request address via DHCP",sy_services:"Services",
 sy_igmp:"IGMP snooping",sy_sysip:"server IP",sy_server:"Server",sy_port:"Port",
+sy_sesstmo:"Session timeout (s)",sy_sesstmo_err:"Session timeout must be 1-65535 s",
 sy_services_note:"Service state reflects the startup config; runtime state is not readable.",
 sy_password:"Admin password",sy_newpw:"New password",sy_repeat:"Repeat",sy_pwapply:"Change password",
 sy_pw_note:"Takes effect immediately; save to flash to keep it after reboot.",sy_console:"Console",
@@ -127,7 +135,7 @@ c_full:"全二重",c_half:"半二重",c_devices:"デバイス",c_yes:"はい",c_
 d_ports:"ポート",d_ports_h:"ポートをクリックすると詳細を表示",d_system:"システム",d_traffic:"トラフィック",
 d_traffic_h:"パケット/秒、リアルタイム",d_txpps:"TX pps",d_rxpps:"RX pps",d_txbad:"TX 異常",d_rxbad:"RX 異常",
 i_host:"ホスト名",i_ip:"IP アドレス",i_mask:"ネットマスク",i_gw:"ゲートウェイ",i_mac:"MAC",i_fw:"ファームウェア",
-i_built:"ビルド日",i_hw:"ハードウェア",i_flash:"フラッシュ",i_syslog:"Syslog",
+i_built:"ビルド日",i_hw:"ハードウェア",i_temp:"温度",i_flash:"フラッシュ",i_syslog:"Syslog",
 p_state:"状態",p_disabled:"無効",p_up:"アップ",p_txgb:"TX 正常 / 異常",p_rxgb:"RX 正常 / 異常",
 p_pkts:"pkts",p_module:"モジュール",p_temp:"温度",p_vcc:"電圧",p_txbias:"TX バイアス",p_txpower:"TX 電力",
 p_rxpower:"RX 電力",p_txfault:"TX 障害",p_txdis:"TX 無効",p_rxlos:"RX 信号ロス",p_adv:"アドバタイズ",
@@ -184,6 +192,7 @@ bw_exceed:"超過時の動作",bw_fc:"フロー制御",bw_drop:"破棄",
 bw_in_err:"入力制限は 0.016〜10000 Mbit/s の範囲で指定してください",bw_out_err:"出力制限は 0.016〜10000 Mbit/s の範囲で指定してください",
 sy_network:"ネットワーク",sy_dhcp:"DHCP を使用",sy_dhcp_t:"DHCP でアドレスを取得",sy_services:"サービス",
 sy_igmp:"IGMP スヌーピング",sy_sysip:"サーバー IP",sy_server:"サーバー",sy_port:"ポート",
+sy_sesstmo:"セッションタイムアウト (秒)",sy_sesstmo_err:"セッションタイムアウトは 1〜65535 秒で指定してください",
 sy_services_note:"サービスの状態は起動設定を反映しています。実行時の状態は読み取れません。",
 sy_password:"管理者パスワード",sy_newpw:"新しいパスワード",sy_repeat:"再入力",sy_pwapply:"パスワードを変更",
 sy_pw_note:"即時に反映されます。再起動後も保持するにはフラッシュに保存してください。",sy_console:"コンソール",
@@ -239,7 +248,7 @@ c_full:"全双工",c_half:"半双工",c_devices:"台设备",c_yes:"是",c_no:"
 d_ports:"端口",d_ports_h:"点击端口查看详情",d_system:"系统",d_traffic:"流量",
 d_traffic_h:"包/秒，实时",d_txpps:"TX pps",d_rxpps:"RX pps",d_txbad:"TX 错误",d_rxbad:"RX 错误",
 i_host:"主机名",i_ip:"IP 地址",i_mask:"子网掩码",i_gw:"网关",i_mac:"MAC",i_fw:"固件",
-i_built:"构建日期",i_hw:"硬件",i_flash:"Flash",i_syslog:"Syslog",
+i_built:"构建日期",i_hw:"硬件",i_temp:"温度",i_flash:"Flash",i_syslog:"Syslog",
 p_state:"状态",p_disabled:"已禁用",p_up:"已连接",p_txgb:"TX 正常 / 错误",p_rxgb:"RX 正常 / 错误",
 p_pkts:"个包",p_module:"模块",p_temp:"温度",p_vcc:"供电电压",p_txbias:"TX 偏置电流",p_txpower:"TX 光功率",
 p_rxpower:"RX 光功率",p_txfault:"TX 故障",p_txdis:"TX 禁用",p_rxlos:"RX 信号丢失",p_adv:"通告能力",
@@ -296,6 +305,7 @@ bw_exceed:"超限动作",bw_fc:"流量控制",bw_drop:"丢弃",
 bw_in_err:"入方向限速范围为 0.016-10000 Mbit/s",bw_out_err:"出方向限速范围为 0.016-10000 Mbit/s",
 sy_network:"网络",sy_dhcp:"使用 DHCP",sy_dhcp_t:"通过 DHCP 获取地址",sy_services:"服务",
 sy_igmp:"IGMP 侦听",sy_sysip:"服务器 IP",sy_server:"服务器",sy_port:"端口",
+sy_sesstmo:"会话超时（秒）",sy_sesstmo_err:"会话超时必须为 1-65535 秒",
 sy_services_note:"服务状态反映启动配置；运行时状态无法读取。",
 sy_password:"管理员密码",sy_newpw:"新密码",sy_repeat:"重复输入",sy_pwapply:"修改密码",
 sy_pw_note:"立即生效；如需重启后保留请保存到 Flash。",sy_console:"控制台",
@@ -408,6 +418,7 @@ bw_exceed:"Al excederse",bw_fc:"Control de flujo",bw_drop:"Descartar",
 bw_in_err:"El límite de entrada debe estar entre 0.016 y 10000 Mbit/s",bw_out_err:"El límite de salida debe estar entre 0.016 y 10000 Mbit/s",
 sy_network:"Red",sy_dhcp:"Usar DHCP",sy_dhcp_t:"Solicitar dirección mediante DHCP",sy_services:"Servicios",
 sy_igmp:"IGMP snooping",sy_sysip:"IP del servidor",sy_server:"Servidor",sy_port:"Puerto",
+sy_sesstmo:"Tiempo de sesión (s)",sy_sesstmo_err:"El tiempo de sesión debe estar entre 1 y 65535 s",
 sy_services_note:"El estado del servicio refleja la configuración de inicio; el estado en ejecución no es legible.",
 sy_password:"Contraseña de administrador",sy_newpw:"Nueva contraseña",sy_repeat:"Repetir",sy_pwapply:"Cambiar contraseña",
 sy_pw_note:"Toma efecto inmediatamente; guarda en flash para conservarla tras el reinicio.",sy_console:"Consola",
@@ -446,6 +457,235 @@ fw_applied:"actualización aplicada",fw_done_t:"Firmware actualizado",
 fw_done:"El switch verificó la imagen y se reinició con ella. La sesión se restableció, así que se te pedirá que vuelvas a iniciar sesión.",
 fw_login:"Ir al inicio de sesión",fw_rebooting:"el switch se está reiniciando...",
 fw_timeout:"el switch no ha vuelto tras 150 s: comprueba la alimentación / consola serie"
+},
+fr:{
+nav_dash:"Tableau de bord",nav_ports:"Ports",nav_stp:"Arborescence",nav_stats:"Statistiques",
+nav_vlan:"LANs virtuels",nav_l2:"Table MAC",nav_mirror:"Mise en mirroir",nav_lag:"Aggrégation",nav_eee:"Energie",
+nav_bw:"Bande passante",nav_system:"Système",nav_fw:"Micro logiciel",
+hdr_dirty:"Changements non sauvegardés",hdr_dirty_t:"La configuration utilisée diffère de celle au démarrage",
+hdr_save:"Sauvegarder en flash",hdr_save_t:"Maintenir la configuration actuelle en flash",
+th_auto:"Système",th_auto_sel:"Système (sélénisé)",sy_display:"Affichage",sy_theme:"Thème",sy_display_note:"Enregistré seulement dans ce navigateur.",th_light:"Clair",th_dark:"Sombre",
+th_sel_light:"Clair (sélénisé)",th_sel_dark:"Sombre (sélénisé)",
+c_port:"Port",c_name:"Nom",c_link:"Lien",c_apply:"Appliquer",c_cancel:"Annuler",c_confirm:"Confirmer",
+c_close:"Fermer",c_refresh:"Raffraichir",c_off:"arrêt",c_offc:"Arrêt",c_down:"arrêt",c_on:"Marche",c_auto:"Auto",c_delete:"Supprimer",
+c_type:"Type",c_state:"Etat",c_enabled:"Activé",c_load:"Charger",c_disable:"Désactivé",c_sfp:"SFP",
+c_full:"full",c_half:"half",c_devices:"Equipements",c_yes:"oui",c_no:"non",
+d_ports:"Ports",d_ports_h:"Cliquez ou survollez pour plus de détails",d_system:"Système",d_traffic:"Trafic",
+d_traffic_h:"paquets/s (en direct)",d_txpps:"TX pps",d_rxpps:"RX pps",d_txbad:"TX KO",d_rxbad:"RX KO",
+i_host:"Nom d'hote",i_ip:"Adresse IP",i_mask:"Masque réseau",i_gw:"Passerelle",i_mac:"Adresse MAC",i_fw:"Micro logiciel",
+i_built:"Compilé le",i_hw:"Matériel",i_temp:"Température",i_flash:"Taille Flash",i_syslog:"Journal système",
+p_state:"Etat",p_disabled:"Inactif",p_up:"Actif",p_txgb:"TX bon / mauvais",p_rxgb:"RX bon / mauvais",
+p_pkts:"paquets",p_module:"Module",p_temp:"Température",p_vcc:"Vcc",p_txbias:"TX biais",p_txpower:"TX puissance",
+p_rxpower:"RX puissance",p_txfault:"TX erreur",p_txdis:"TX désactivé",p_rxlos:"RX pertes de signaux",p_adv:"Capacités",
+pt_title:"Configuration du port",pt_conn:"Connecté à",pt_speed:"Vitesse",pt_mtu:"MTU",
+pt_sfp_note:"La vitesse SFP est paramétrée pour le port et n'est pas enregistrée dans la configuration de démarrage.",
+pt_name_err:"Nom du port: 1 à 15 caractères, sans espaces",pt_mtu_err:"MTU doit être comrpis entre 64 et 16383",
+stp_title:"Arborescence",stp_h:"RSTP, 802.1w",stp_version:"Protocole",stp_v_stp:"Compatible STP",
+stp_prio:"Priorité",stp_hello:"Bonjour [s]",stp_maxage:"Age max [s]",stp_fwd:"Délai de transmission [s]",
+stp_txhold:"TX en attente",stp_bridge_apply:"Appliquer les paramètres du pont",
+stp_off_msg:"Arborescence désactivée: Tous les ports sont retransmis.",stp_bridge:"Pont",stp_root:"Racine",
+stp_root_self:"Ce pont est la racine",stp_via:"via le port",stp_cost:"coût du chemin",stp_tc:"changements de topologie",
+stp_prio_note:"La priorité la plus basse devient la racine (défaut 8 à 32768). Les paramètres s'appliquent immediatement; utiliser Sauvegarder en flash pour les conserver.",
+stp_portcfg:"Configuration du port",stp_edge:"Port terminal",stp_pcost:"Coût du chemin",stp_pprio:"Priorité",
+stp_guard:"Protection",stp_filter:"Filtre BPDU",stp_p2p:"Point-à-point",
+stp_port_note:"Les ports en bordure sont transmis immediatemment et ne change pas la topologie; Auto traite le port comme une bordure après 3s sans BPDUs, et chaque BPDU reçu le révoque. Le coût du chemin  0 = automatique.",
+stp_status:"Statut du port",stp_role:"Rôle",stp_db:"Pont désigné",stp_dp:"Port désigné",
+stp_dc:"Coût désigné",stp_oedge:"Oper. terminales",stp_op2p:"Oper. en P2P",
+stp_s0:"désactivé",stp_s1:"bloquage",stp_s2:"apprentissage",stp_s3:"retransmission",
+stp_r1:"Racine",stp_r2:"Designé",stp_r3:"Alternatif",stp_trip:"protection déclenchée",
+stp_g_none:"Aucun",stp_g_bpdu:"BPDU",stp_g_root:"Racine",
+stp_en_q:"Activer l'arbrescence?",
+stp_en_d:"Les ports sont d'abord bloqués et cela prend deux fois le délai de retransmission pour atteindre l'état de retransmission; les ports en bordures recouvrent immédiatement leur état.",
+stp_dis_q:"Désactiver l'arborescence ?",stp_dis_d:"Tous les ports vont être retransmis; la protection de boucles est perdue.",
+stp_cost_err:"Le coût du chemin doit être compris entre 0 et 200000000",
+st_title:"Statiqtique du port",st_h:"cumul depuis le démarrage",st_txg:"TX OK",st_txb:"TX KO",st_rxg:"RX OK",
+st_rxb:"RX KO",st_details:"Détails",st_counters:"Compteur MIB",st_nonzero:"non-zero seulement",
+st_autoref:"rafraichissement automatique",st_counter:"Compteur",st_value:"Valeur",st_fail:"Erreur au chargement des compteurs",
+v_title:"VLANs",v_vid:"VID",v_members:"Membres",v_tagged:"Tagué",v_untagged:"Détagué",v_pvid_on:"PVID on",
+v_empty:"Aucun VLANs configuré.",v_mgmt:"VLAN de management",v_mgmt_none:"détagué",v_editor:"Editeur de VLAN",
+v_optional:"optionel",v_setmgmt:"Mette en VLAN de management",v_setmgmt_t:"Mettre celui-ci en VLAN de management",
+v_member:"Membre",v_pvid:"PVID",
+v_legend:"U = Membre détagué (UnTagged), T = membre tagué (Tagged), - = non membre. PVID (Port VLan ID) assigne ce VLAN au trafic entrant non tagué.",
+v_ingress:"Filtrage entrant",v_ingress_h:"en ériture seule: cet état n'est pas lisible depuis le communtateur réseau",
+v_accept:"Accepté",v_ing_all:"Tous",v_ing_apply:"Appliquer les filtes",v_del_t:"Supprimer le VLAN",
+v_del_q:"Supprimer le VLAN {n}?",v_del_d:"Les ports conservent leur PVID tant qu'ils ne sont pas réassignés.",
+v_vid_err:"Entrez un identifiant VLAN (1-4094)",v_name_err:"Le nom doit commencer par une lettre (lettre, chiffres, _)",
+v_loaded:"VLAN chargés {n}",v_notfound:"VLAN {n} non trouvé (un nouveau peut toutefois être créé)",
+v_nomember:"Selectionnez au moins un port membre (ou supprimez le VLAN)",
+v_ing_none:"Sélectionnez le mode entrant pour au moins un port",v_vid_first:"Entrez un identifiant VLAN d'abord",
+v_mgmt_q:"Mettre ce VLAN {n} en tant que VLAN de management?",
+v_mgmt_d:"Ce commutateur commencera par taguer son propre trafic avec ce VLAN. Si le port avec lequel vous êtes connecté ne le permet pas, cette page deviendra inaccessible et les paramètres ne pourront plus être changés que via la console.",
+l2_title:"Table des adresses MAC",l2_filter:"filtre...",l2_flush:"Effacer les entrées apprises",l2_static:"static",
+l2_learned:"appris",l2_loading:"chargement...",l2_failed:"chargement non réussi",l2_entries:"entrées",
+l2_del_t:"Supprimer l'entrée",l2_flush_q:"Effacer toutes les entrées MAC apprises?",
+m_title:"Duplication de ports",m_active:"actif",m_monitor:"Port de supervision",m_mirror:"Mirroir",m_both:"RX&TX",
+m_note:"RX&TX = duplique RX et TX du port vers le port de supervision.",m_none:"Selectionnez au moins un port à dupliquer",
+lag_hash:"Hachage:",lag_note:"Un groupe d'agrégation de Lien (LAG) nécessite au moins un membre pour être sauvegardé dans la configuration de démarrage; Utiliser un groupe vide fait office de remise à zero.",
+lag_clear_q:"Effacer l'agrégation {n}?",lag_clear_d:"Tous les ports membres vont redevenir normaux.",
+e_title:"Gestion énergétique des ports",e_adv:"Capacités",e_lp:"Capacité du partenaire",e_active:"Actif",e_enable:"Basse consommation",
+e_note:"Capacité de l'hôte et des partenaires : 100M, 1G, 2.5G. Les ports SFP ne peuvent pas bénéficier de l'EEE.",
+e_idle:"Inactif",e_na:"N/A",
+bw_title:"Limitations de bande passante",bw_h:"Mbit/s, 0.016-10000",bw_in:"Limite entrante",bw_out:"Limite sortante",
+bw_exceed:"Lorsque dépassé",bw_fc:"Limiter",bw_drop:"Rejetter",
+bw_in_err:"La limite entrante doit être comprise entre 0.016 et 10000 Mbit/s",bw_out_err:"La limite sortante doit être comprise entre 0.016 et 10000 Mbit/s",
+sy_network:"Réseau",sy_dhcp:"Uiliser DHCP",sy_dhcp_t:"Aquérir l'adresse via le protocole DHCP",sy_services:"Services",
+sy_igmp:"Surveillance IGMP",sy_sysip:"IP du serveur...",sy_server:"Serveur",sy_port:"Port",
+sy_sesstmo:"Temps mort de session (s)",sy_sesstmo_err:"Le temps morts de session doit être compris en 1-65535 s",  
+sy_services_note:"L'état de service dépend de la configuration de démarrage; Le temps de fonctionnement n'est pas consultable.",
+sy_password:"Gestion de l'accès",sy_newpw:"Mot de passe",sy_repeat:"Confirmation",sy_pwapply:"Changer le mot de passe",
+sy_pw_note:"Prends effet immédiatement; Sauvegardez en flash afin de conserver la configuration lors du redémarrage.",sy_console:"Console",
+sy_cmd:"Ligne de commande...",sy_send:"Envoyer",sy_startup:"Configuration de démarrage",sy_replayed:"Rejouée à chaque redémarrage",
+sy_reload:"Recharger depuis la mémoire flash",sy_write:"Ecrire en mémoire flash",sy_unknown_note:"Les lignes incorrectes sont mises en évidence avant l'écriture.",
+sy_maint:"Maintenance",sy_reboot:"Redémarre le commutateur",sy_lang:"Langage",
+sy_ip_err:"Erreur d'IP / masque réseau / passerelle",sy_host_err:"Nom d'hôte : 1 à 23 caractères, sans espace ni apostrophes",
+sy_net_q:"Appliquer les paramètres réseau?",sy_net_d:"L'adresse IP de  management va devenir {ip}: merci de réouvrir le page depuis cette adresse.",
+sy_ip_changed:"L'adresse IP a changée, reconnectez-vous à http://{ip}/",sy_dhcp_q:"Passer en DHCP?",
+sy_dhcp_d:"Le commutateur va demander une addresse via le DHCP. Vous devrez rechercher sa prochaine adresse IP pour vous reconnecter.",
+sy_sysip_err:"Adresse IP du serveur Syslog invalide",sy_sysport_err:"Le port Syslog doit être compris entre 1 et 65535",
+sy_pw_len:"Mot de passe : 1 à 20 caractères",sy_pw_space:"Le mot de passe ne doit pas contenir d'espaces",sy_pw_match:"Les mots de passe ne correspondent pas",
+sy_pw_q:"Changer le mot de passe d'administration?",sy_pw_d:"Cela prend effet immédiatement dès la prochaine connection. Enregistrez en Flash pour rendre la modification persistante.",
+sy_reboot_q:"Redémarrer le commutateur ?",sy_reboot_d:"Il y a des paramètres NON SAUVEGARDES qui vont être perdus. Sauvegardez-les au préalable en mémoire flash si vous souhaitez les conserver.",
+sy_rebooting:"Redémarrage, reconnectez-vous d'ici 20s",sy_bytes:"bytes",
+cw_title:"Enregistrer cette configuration de démarrage?",cw_save_title:"Enregistrer la configuration active en mémoire flash?",
+cw_info:"{n} / 2048 bytes, qui seront rejouées ligne par ligne à chaque redémarrage",
+cw_toolarge:"Trop grand : La quota du secteur de démarrage ne peut excéder 2048 bytes. Supprimez des lignes.",
+cw_longline:"La ligne {n} est longue de {m} bytes: Le commutateur ne peut exécuter des lignes de plus de 126 bytes et les omettra donc au démarragee, l'écriture est refusé. Raccourcissez les d'abord.",
+cw_unknown:"Ne respecte pas la grammaire de configuration (sera néanmoins sauvegardé): ",cw_empty:"(vide)",
+cw_writing:"Configuration enregistrée...",cw_failed:"Echec de l'enregistrement de la configuration: HTTP {n}",
+cw_verify_fail:"Verification erronée: La mémoire flash présente des différences par rapport à ce qui a été transmis. Le log de commande ne sera pas éffacé.",
+cw_saved:"Configuration de démarrage sauvegardée et vérifiée",cw_collect:"Récolement des modification des paramètres courants...",
+t_applied:"Appliqué: {c}",t_cmds:"{n} commande(s) appliquée(s)",t_rejected:"commandes rejetées: {c}",t_failed:"échecs: {c}",
+fw_title:"Mise à jour du micro-logiciel",
+fw_intro:"Charge une image RTLPlayground (512 KiB .bin). L'image est envoée en mémoire flash, analysée et sa somme de contrôle est vérifiée; en cas de succès le commutateur va redémarrer, re-verifiez l'image et appliquez-là. LA configuration de démarrage est conservée.",
+fw_upload:"Charger",fw_checking:"{f}: {n} bytes. Vérification...",fw_size_err:"la taille est {n} alors que nous attendons 524288 (512 KiB)",
+fw_magic_err:"Entête de banque de donnée manquant / contrôle LJMP: ce n'est pas une image de firmware",fw_crc_err:"Somme de contrôle erronée: image corrompue",
+fw_valid:"Image RTLPlayground valide (taille, LJMP et somme de contrôle OK)",fw_q:"Chargement du firmware?",
+fw_d:"Si la somme de contrôle est correcte, le commutateur va redémarrer tout seul et charger la nouvelle image lors du démarrage (la configuration est préservée). Ne pas éteindre l'appareil avant que les voyants ne s'éteignent.",
+fw_finishing:"Fin d'écriture en mémoire flash... {s} s",fw_uploading:"Chargement... {p}% / {s} s",
+fw_verified:"Somme de contrôle vérifiée, le commutateur redémarre...",
+fw_rejected:"L'image est rejettée en raison d'une somme de contrôle incorrecte, rien n'a été appliqué",
+fw_lost:"Erreur lors du chargement: connection perdue à mi-transfert",
+fw_noreboot:"Pas de redemarrage détecté: l'image a certainement été refusée. Si vous chargesz un ancien firmware, verifiez la version affichée après l'écran de connection.",
+fw_applied:"Mise à jour effectuée",fw_done_t:"Firmware mis à jour",
+fw_done:"Le commutateur a vérifié l'image et vient de redémarrer. La session a été remise à zero, vous devez vous reconnecter.",
+fw_login:"Vers l'écran de connection",fw_rebooting:"Le commutateur redémarre...",
+fw_timeout:"Le commutateur n'est plus joignable depuis 150 s: verifiez l'alimentation ou utilisez la console série"
+},
+de:{
+nav_dash:"Übersicht",nav_ports:"Ports",nav_stp:"Spanning Tree",nav_stats:"Statistik",
+nav_vlan:"VLANs",nav_l2:"MAC-Tabelle",nav_mirror:"Spiegelung",nav_lag:"LAG",nav_eee:"EEE",
+nav_bw:"Bandbreite",nav_system:"System",nav_fw:"Firmware",
+hdr_dirty:"ungespeicherte Änderungen",hdr_dirty_t:"Laufende Konfiguration weicht von der Startkonfiguration ab",
+hdr_save:"Im Flash speichern",hdr_save_t:"Laufende Konfiguration dauerhaft im Flash speichern",
+th_auto:"System",th_auto_sel:"System (Selenized)",sy_display:"Anzeige",sy_theme:"Farbschema",sy_display_note:"Wird nur in diesem Browser gespeichert.",th_light:"Hell",th_dark:"Dunkel",
+th_sel_light:"Selenized Hell",th_sel_dark:"Selenized Dunkel",
+c_port:"Port",c_name:"Name",c_link:"Link",c_apply:"Übernehmen",c_cancel:"Abbrechen",c_confirm:"Bestätigen",
+c_close:"Schliessen",c_refresh:"Aktualisieren",c_off:"aus",c_offc:"Aus",c_down:"getrennt",c_on:"Ein",c_auto:"Auto",c_delete:"Löschen",
+c_type:"Typ",c_state:"Zustand",c_enabled:"Aktiviert",c_load:"Laden",c_disable:"Deaktivieren",c_sfp:"SFP",
+c_full:"voll",c_half:"halb",c_devices:"Geräte",c_yes:"ja",c_no:"nein",
+d_ports:"Ports",d_ports_h:"Port anklicken für Details",d_system:"System",d_traffic:"Datenverkehr",
+d_traffic_h:"Pakete/s, live",d_txpps:"TX Pakete/s",d_rxpps:"RX Pakete/s",d_txbad:"TX fehlerhaft",d_rxbad:"RX fehlerhaft",
+i_host:"Hostname",i_ip:"IP-Adresse",i_mask:"Netzmaske",i_gw:"Gateway",i_mac:"MAC",i_fw:"Firmware",
+i_built:"Erstellt",i_hw:"Hardware",i_temp:"Temperatur",i_flash:"Flash",i_syslog:"Syslog",
+p_state:"Zustand",p_disabled:"deaktiviert",p_up:"verbunden",p_txgb:"TX gut / fehlerhaft",p_rxgb:"RX gut / fehlerhaft",
+p_pkts:"Pakete",p_module:"Modul",p_temp:"Temperatur",p_vcc:"Vcc",p_txbias:"TX-Bias",p_txpower:"Sendeleistung",
+p_rxpower:"Empfangsleistung",p_txfault:"TX-Fehler",p_txdis:"TX deaktiviert",p_rxlos:"RX LOS",p_adv:"Angeboten",
+pt_title:"Port-Konfiguration",pt_conn:"Verbunden",pt_speed:"Geschwindigkeit",pt_mtu:"MTU",
+pt_sfp_note:"Die SFP-Geschwindigkeit wird pro Steckplatz gesetzt und nicht in der Startkonfiguration gespeichert.",
+pt_name_err:"Port-Name: 1-15 Zeichen, keine Leerzeichen",pt_mtu_err:"MTU muss zwischen 64 und 16383 liegen",
+stp_title:"Spanning Tree",stp_h:"RSTP, 802.1w",stp_version:"Version",stp_v_stp:"STP-kompatibel",
+stp_prio:"Bridge-Priorität",stp_hello:"Hello [s]",stp_maxage:"Max. Alter [s]",stp_fwd:"Forward Delay [s]",
+stp_txhold:"TX Hold",stp_bridge_apply:"Bridge-Einstellungen übernehmen",
+stp_off_msg:"Spanning Tree ist deaktiviert: Alle Ports leiten weiter.",stp_bridge:"Bridge",stp_root:"Root",
+stp_root_self:"diese Bridge ist Root",stp_via:"über Port",stp_cost:"Pfadkosten",stp_tc:"Topologieänderungen",
+stp_prio_note:"Die niedrigere Priorität gewinnt die Root-Wahl (Standard 8 = 32768). Einstellungen wirken sofort; mit „Im Flash speichern“ bleiben sie erhalten.",
+stp_portcfg:"Port-Konfiguration",stp_edge:"Edge",stp_pcost:"Pfadkosten",stp_pprio:"Priorität",
+stp_guard:"Guard",stp_filter:"BPDU-Filter",stp_p2p:"Punkt-zu-Punkt",
+stp_port_note:"Edge-Ports leiten sofort weiter und lösen keine Topologieänderung aus; bei Auto gilt ein Port nach 3 s ohne BPDUs als Edge, jede empfangene BPDU hebt das wieder auf. Pfadkosten 0 = automatisch.",
+stp_status:"Port-Status",stp_role:"Rolle",stp_db:"Designated Bridge",stp_dp:"Designated Port",
+stp_dc:"Designated Cost",stp_oedge:"Edge (aktiv)",stp_op2p:"P2P (aktiv)",
+stp_s0:"deaktiviert",stp_s1:"blockiert",stp_s2:"lernt",stp_s3:"leitet weiter",
+stp_r1:"Root",stp_r2:"Designated",stp_r3:"Alternate",stp_trip:"Guard ausgelöst",
+stp_g_none:"Keiner",stp_g_bpdu:"BPDU",stp_g_root:"Root",
+stp_en_q:"Spanning Tree aktivieren?",
+stp_en_d:"Die Ports starten blockiert und brauchen bis zum doppelten Forward Delay, bis sie weiterleiten; Edge-Ports sind sofort wieder aktiv.",
+stp_dis_q:"Spanning Tree deaktivieren?",stp_dis_d:"Alle Ports leiten sofort weiter; der Schutz vor Netzwerkschleifen entfällt.",
+stp_cost_err:"Pfadkosten müssen zwischen 0 und 200000000 liegen",
+st_title:"Port-Statistik",st_h:"Summen seit dem Start",st_txg:"TX gut",st_txb:"TX fehlerhaft",st_rxg:"RX gut",
+st_rxb:"RX fehlerhaft",st_details:"Details",st_counters:"MIB-Zähler",st_nonzero:"nur ungleich null",
+st_autoref:"automatisch aktualisieren",st_counter:"Zähler",st_value:"Wert",st_fail:"Zähler konnten nicht geladen werden",
+v_title:"VLANs",v_vid:"VID",v_members:"Mitglieder",v_tagged:"Tagged",v_untagged:"Untagged",v_pvid_on:"PVID auf",
+v_empty:"Keine VLANs konfiguriert.",v_mgmt:"Management-VLAN",v_mgmt_none:"untagged",v_editor:"VLAN-Editor",
+v_optional:"optional",v_setmgmt:"Als Management-VLAN",v_setmgmt_t:"Dieses VLAN zum Management-VLAN machen",
+v_member:"Mitglied",v_pvid:"PVID",
+v_legend:"U = Mitglied untagged, T = Mitglied tagged, - = kein Mitglied. PVID ordnet eingehenden Verkehr ohne Tag diesem VLAN zu.",
+v_ingress:"Ingress-Filter",v_ingress_h:"nur schreibbar: der Zustand lässt sich vom Switch nicht auslesen",
+v_accept:"Annehmen",v_ing_all:"Alle",v_ing_apply:"Ingress-Modi übernehmen",v_del_t:"VLAN löschen",
+v_del_q:"VLAN {n} löschen?",v_del_d:"Die Ports behalten ihre PVID, bis sie neu zugewiesen wird.",
+v_vid_err:"VLAN-ID eingeben (1-4094)",v_name_err:"Der Name muss mit einem Buchstaben beginnen (Buchstaben, Ziffern, _)",
+v_loaded:"VLAN {n} geladen",v_notfound:"VLAN {n} nicht gefunden (es kann neu angelegt werden)",
+v_nomember:"Mindestens einen Mitglieds-Port wählen (oder das VLAN stattdessen löschen)",
+v_ing_none:"Für mindestens einen Port einen Ingress-Modus wählen",v_vid_first:"Zuerst eine VLAN-ID eingeben",
+v_mgmt_q:"VLAN {n} als Management-VLAN setzen?",
+v_mgmt_d:"Der Switch versieht dann seinen eigenen Verkehr mit diesem VLAN-Tag. Führt der Port, über den du verbunden bist, dieses VLAN nicht, ist diese Seite nicht mehr erreichbar und die Einstellung lässt sich nur noch über die serielle Konsole zurücknehmen.",
+l2_title:"MAC-Adresstabelle",l2_filter:"filtern...",l2_flush:"Gelernte Einträge löschen",l2_static:"statisch",
+l2_learned:"gelernt",l2_loading:"lädt...",l2_failed:"Laden fehlgeschlagen",l2_entries:"Einträge",
+l2_del_t:"Eintrag löschen",l2_flush_q:"Alle gelernten MAC-Einträge löschen?",
+m_title:"Port-Spiegelung",m_active:"aktiv",m_monitor:"Monitor-Port",m_mirror:"Spiegeln",m_both:"Beide",
+m_note:"Beide = RX und TX des Ports auf den Monitor-Port spiegeln.",m_none:"Mindestens einen zu spiegelnden Port wählen",
+lag_hash:"Hash:",lag_note:"Eine LAG braucht mindestens ein Mitglied, um in der Startkonfiguration gespeichert zu werden; eine leere Gruppe zu übernehmen löscht sie.",
+lag_clear_q:"LAG {n} auflösen?",lag_clear_d:"Alle Mitglieds-Ports kehren in den Normalbetrieb zurück.",
+e_title:"Energy Efficient Ethernet",e_adv:"Angeboten",e_lp:"Gegenstelle",e_active:"Aktiv",e_enable:"Aktivieren",
+e_note:"Angebotene und von der Gegenstelle unterstützte Stufen je Geschwindigkeit: 100M, 1G, 2.5G. SFP-Ports unterstützen kein EEE.",
+e_idle:"inaktiv",e_na:"k. A.",
+bw_title:"Bandbreitenbegrenzung",bw_h:"Mbit/s, 0.016-10000",bw_in:"Eingangslimit",bw_out:"Ausgangslimit",
+bw_exceed:"Bei Überschreitung",bw_fc:"Flusskontrolle",bw_drop:"Verwerfen",
+bw_in_err:"Eingangslimit muss zwischen 0.016 und 10000 Mbit/s liegen",bw_out_err:"Ausgangslimit muss zwischen 0.016 und 10000 Mbit/s liegen",
+sc_title:"Storm Control",sc_h:"pro Port und Verkehrsart, leer = aus",sc_bcast:"Broadcast",sc_mcast:"Multicast",
+sc_ucast:"Unbekannter Unicast",sc_umcast:"Unbekannter Multicast",sc_err:"Grenzwert muss 1-1048575 pps oder 1-10000000 kbit/s betragen",
+sc_note:"Pakete einer Verkehrsart über ihrem Grenzwert werden beim Eintritt in den Switch verworfen.",
+sy_network:"Netzwerk",sy_dhcp:"DHCP verwenden",sy_dhcp_t:"Adresse per DHCP beziehen",sy_services:"Dienste",
+sy_igmp:"IGMP Snooping",sy_sysip:"Server-IP",sy_server:"Server",sy_port:"Port",
+sy_sesstmo:"Sitzungs-Timeout (s)",sy_sesstmo_err:"Sitzungs-Timeout muss zwischen 1 und 65535 s liegen",
+sy_services_note:"Der Dienststatus entspricht der Startkonfiguration; der laufende Zustand ist nicht auslesbar.",
+sy_password:"Admin-Passwort",sy_newpw:"Neues Passwort",sy_repeat:"Wiederholen",sy_pwapply:"Passwort ändern",
+sy_pw_note:"Wirkt sofort; im Flash speichern, damit es nach einem Neustart erhalten bleibt.",sy_console:"Konsole",
+sy_cmd:"CLI-Befehl...",sy_send:"Senden",sy_startup:"Startkonfiguration",sy_replayed:"wird bei jedem Start ausgeführt",
+sy_reload:"Aus dem Flash neu laden",sy_write:"In den Flash schreiben",sy_unknown_note:"Unbekannte Zeilen werden vor dem Schreiben hervorgehoben.",
+sy_maint:"Wartung",sy_reboot:"Switch neu starten",sy_lang:"Sprache",
+sy_ip_err:"Ungültige IP / Netzmaske / Gateway",sy_host_err:"Hostname: 1-23 druckbare Zeichen, keine Leerzeichen oder Anführungszeichen",
+sy_net_q:"Netzwerkeinstellungen übernehmen?",sy_net_d:"Die Management-IP ändert sich auf {ip}: Diese Seite muss dort neu geöffnet werden.",
+sy_ip_changed:"IP geändert, neu verbinden unter http://{ip}/",sy_dhcp_q:"Auf DHCP umstellen?",
+sy_dhcp_d:"Der Switch bezieht seine Adresse per DHCP. Du musst seine neue IP herausfinden, um dich wieder zu verbinden.",
+sy_sysip_err:"Ungültige IP des Syslog-Servers",sy_sysport_err:"Syslog-Port muss zwischen 1 und 65535 liegen",
+sy_pw_len:"Passwort: 1-20 Zeichen",sy_pw_space:"Das Passwort darf keine Leerzeichen enthalten",sy_pw_match:"Die Passwörter stimmen nicht überein",
+sy_pw_q:"Admin-Passwort ändern?",sy_pw_d:"Gilt sofort für neue Anmeldungen. Im Flash speichern, damit es erhalten bleibt.",
+sy_reboot_q:"Switch neu starten?",sy_reboot_d:"Es gibt UNGESPEICHERTE Änderungen, sie gehen verloren. Zuerst im Flash speichern, wenn du sie behalten willst.",
+sy_rebooting:"Neustart läuft, in etwa 20 s neu verbinden",sy_bytes:"Bytes",
+cw_title:"Diese Startkonfiguration schreiben?",cw_save_title:"Laufende Konfiguration im Flash speichern?",
+cw_info:"{n} / 2048 Bytes, wird bei jedem Start Zeile für Zeile ausgeführt",
+cw_toolarge:"Zu gross: Der Konfigurationssektor fasst höchstens 2048 Bytes. Zuerst Zeilen entfernen.",
+cw_longline:"Zeile {n} ist {m} Bytes lang: Der Switch kann beim Start nur Zeilen bis 126 Bytes ausführen und würde sie überspringen, deshalb wird das Schreiben abgelehnt. Zuerst kürzen.",
+cw_unknown:"Nicht in der bekannten Konfigurationssyntax (wird trotzdem geschrieben): ",cw_empty:"(leer)",
+cw_writing:"Konfiguration wird geschrieben...",cw_failed:"Schreiben der Konfiguration fehlgeschlagen: HTTP {n}",
+cw_verify_fail:"Prüfung fehlgeschlagen: Der Flash-Inhalt weicht vom Gesendeten ab. Befehlsprotokoll wurde NICHT gelöscht.",
+cw_saved:"Startkonfiguration gespeichert und geprüft",cw_collect:"Laufende Änderungen werden gesammelt...",
+t_applied:"Übernommen: {c}",t_cmds:"{n} Befehl(e) übernommen",t_rejected:"Befehl abgelehnt: {c}",t_failed:"fehlgeschlagen: {c}",
+fw_title:"Firmware-Update",
+fw_intro:"Ein RTLPlayground-Image hochladen (.bin, 512 KiB). Das Image wird im Flash abgelegt und per CRC geprüft; ist es in Ordnung, startet der Switch neu, prüft das Image erneut und übernimmt es. Die Startkonfiguration bleibt erhalten.",
+fw_upload:"Hochladen",fw_checking:"{f}: {n} Bytes. Wird geprüft...",fw_size_err:"Grösse ist {n}, erwartet 524288 (512 KiB)",
+fw_magic_err:"Bank-Header / LJMP-Kennung fehlt: kein Firmware-Image",fw_crc_err:"CRC16-Prüfung fehlgeschlagen: Image beschädigt",
+fw_valid:"gültiges RTLPlayground-Image (Grösse, Kennung und CRC16 in Ordnung)",fw_q:"Firmware hochladen?",
+fw_d:"Ist die Prüfsumme korrekt, startet der Switch neu und übernimmt das Image beim Hochfahren (die Startkonfiguration bleibt erhalten). Nicht vom Strom trennen, bis er wieder erreichbar ist.",
+fw_finishing:"Flash wird fertig beschrieben... {s} s",fw_uploading:"wird hochgeladen... {p}% / {s} s",
+fw_verified:"Prüfsumme bestätigt, der Switch startet neu...",
+fw_rejected:"der Switch hat das Image abgelehnt (falsche Prüfsumme), es wurde nichts übernommen",
+fw_lost:"Hochladen fehlgeschlagen: Verbindung während der Übertragung abgebrochen",
+fw_noreboot:"kein Neustart erkannt: Das Image wurde sehr wahrscheinlich abgelehnt. Bei einem Update von alter Firmware nach dem erneuten Anmelden die Version in der Seitenleiste prüfen.",
+fw_applied:"Update übernommen",fw_done_t:"Firmware aktualisiert",
+fw_done:"Der Switch hat das Image geprüft und damit neu gestartet. Die Sitzung wurde zurückgesetzt, du wirst erneut zur Anmeldung aufgefordert.",
+fw_login:"Zur Anmeldung",fw_rebooting:"Switch startet neu...",
+fw_timeout:"Der Switch ist nach 150 s nicht zurück: Stromversorgung / serielle Konsole prüfen"
 }
 };
 var rtlLang=(function(){
@@ -541,6 +781,7 @@ var CONF_CMDS=[
   /^ip\s+(\d{1,3}\.){3}\d{1,3}$/,/^ip\s+dhcp$/,
   /^gw\s+(\d{1,3}\.){3}\d{1,3}$/,/^netmask\s+(\d{1,3}\.){3}\d{1,3}$/,
   /^syslog\s+(on|off)$/,/^syslog\s+ip\s+(\d{1,3}\.){3}\d{1,3}$/,/^syslog\s+port\s+\d{1,5}$/,
+  /^session\s+\d{1,5}$/,
   /^passwd\s+\S+$/,/^hostname\s+\S{1,23}$/,
   /^vlan\s+\d{1,4}\s+d$/,/^vlan\s+\d{1,4}\s+mgmt$/,
   /^vlan\s+\d{1,4}(\s+[a-zA-Z]\w*)?(\s+\d{1,2}t?)+$/,
@@ -548,6 +789,7 @@ var CONF_CMDS=[
   /^ingress(\s+\d{1,2}[tua])+$/,/^ingress\s+[tua]$/,
   /^port\s+\d{1,2}\s+(10m|100m|1g|2g5|5g|10g|auto|on|off)(\s+(half|full))?$/,
   /^port\s+\d{1,2}\s+name\s+\S+$/,
+  /^port\s+\d{1,2}\s+lldp\s+(permit|block)+$/,
   /^eee\s+(on|off)(\s+\d{1,2})?(\s+(100m|1g|2g5))?$/,
   /^mirror(\s+\d{1,2})(\s+\d{1,2}[tr]?)+$/,/^mirror\s+off$/,
   /^lag\s+[1-4](\s+\d{1,2})+$/,/^lag\s+[1-4]\s+d$/,/^laghash\s+[1-4](\s+\w+)+$/,
@@ -558,8 +800,9 @@ var CONF_CMDS=[
   /^stp\s+(port\s+\d{1,2}|lag\s+[1-4])\s+cost\s+\d{1,9}$/,/^stp\s+(port\s+\d{1,2}|lag\s+[1-4])\s+prio\s+\d{1,3}$/,
   /^stp\s+(port\s+\d{1,2}|lag\s+[1-4])\s+guard\s+(none|bpdu|root)$/,/^stp\s+(port\s+\d{1,2}|lag\s+[1-4])\s+filter\s+(on|off)$/,
   /^stp\s+(port\s+\d{1,2}|lag\s+[1-4])\s+p2p\s+(auto|on|off)$/,
-  /^igmp\s+(on|off)$/,/^mtu\s+\d{1,2}\s+\d+$/,
+  /^igmp\s+(on|off)$/,/^mtu\s+\d{1,2}\s+\d+$/,/^lldp\s+(on|off)$/,
   /^bw\s+(in|out)\s+\d{1,2}\s+\S+$/,
+  /^storm\s+\d{1,2}\s+(bcast|mcast|ucast|umcast)\s+(off|\d{1,8}\s+(pps|kbps))$/,
 ];
 function isConfCmd(line){
   for(var i=0;i<CONF_CMDS.length;i++)if(CONF_CMDS[i].test(line))return true;
@@ -617,7 +860,9 @@ var TABS=[
   {id:"vlan",  icon:"M12 3v6M12 9l-7 5M12 9l7 5M5 14v5M19 14v5M3 21h4M17 21h4"},
   {id:"l2",    icon:"M4 5h16M4 12h16M4 19h10"},
   {id:"mirror",icon:"M12 3v18M7 8l-4 4 4 4M17 8l4 4-4 4"},
+  {id:"isolate",icon:"M4 4h6v6H4zM14 14h6v6h-6zM14 4h6v6h-6zM4 14h6v6H4z"},
   {id:"lag",   icon:"M7 8a4 4 0 100 8h3M17 8a4 4 0 110 8h-3M9 12h6"},
+  {id:"lldp",  icon:"M11 12a1 1 0 002 0 1 1 0 00-2 0M8.5 8.5a5 5 0 000 7M15.5 8.5a5 5 0 010 7M5.6 5.6a9 9 0 000 12.8M18.4 5.6a9 9 0 010 12.8"},
   {id:"eee",   icon:"M13 2L4 14h6l-1 8 9-12h-6z"},
   {id:"bw",    icon:"M4 18a8 8 0 0116 0M12 18l4-6"},
   {id:"system",icon:"M12 8a4 4 0 100 8 4 4 0 000-8zM4 12h2M18 12h2M12 4v2M12 18v2M6 6l1.5 1.5M16.5 16.5L18 18M18 6l-1.5 1.5M7.5 16.5L6 18"},
@@ -799,7 +1044,7 @@ function portDetail(i){
 function renderInfo(){
   var m=[["i_host","hostname"],["i_ip","ip_address"],["i_mask","ip_netmask"],
     ["i_gw","ip_gateway"],["i_mac","mac_address"],["i_fw","sw_ver"],["i_built","build_date"],
-    ["i_hw","hw_ver"],["i_flash","flash_size"],["i_syslog","syslog_server"]];
+    ["i_hw","hw_ver"],["i_temp","chip_temp"],["i_flash","flash_size"],["i_syslog","syslog_server"]];
   var tb=$("sysinfo");tb.innerHTML="";
   m.forEach(function(r){
     var v=S.info[r[1]];
@@ -1472,6 +1717,76 @@ $("moff").addEventListener("click",function(){
 });
 tabHooks.mirror={enter:function(){needPorts(function(){buildMirror();mirrorLoad().catch(function(){})})}};
 
+var isoAllow=[];
+function isoBox(r,c){return $("iso"+r+"_"+c)}
+function isoMark(){
+  for(var r=1;r<=S.n;r++){
+    var full=true;
+    for(var c=1;c<=S.n+1;c++){var b=isoBox(r,c);if(b&&!b.checked)full=false;}
+    $("isoh"+r).style.color=full?"":"var(--bad)";
+  }
+}
+function isoTouch(){$("isotbl").dataset.dirty="1";isoMark()}
+function isoTh(row,txt,attrs){var e=h("th",attrs);e.textContent=txt;row.appendChild(e);return e}
+function buildIso(){
+  var tb=$("isotbl");
+  if(tb.tBodies[0].rows.length)return;
+  var h1=tb.tHead.insertRow(),h2=tb.tHead.insertRow();
+  isoTh(h1,t("iso_from"),{rowspan:"2"});isoTh(h1,t("iso_to"),{colspan:String(S.n),style:"text-align:center"});isoTh(h1,"CPU",{rowspan:"2"});
+  for(var c=1;c<=S.n;c++)isoTh(h2,String(c),{style:"text-align:center"});
+  for(var r=1;r<=S.n;r++){
+    var tr=tb.tBodies[0].insertRow();
+    isoTh(tr,String(r),{id:"isoh"+r});
+    for(c=1;c<=S.n+1;c++){
+      var td=tr.insertCell();
+      td.style.textAlign="center";
+      if(r===c){td.className="mut";td.textContent="\u2022";continue;}
+      td.appendChild(h("input",{type:"checkbox",id:"iso"+r+"_"+c,onchange:isoTouch}));
+    }
+  }
+}
+function isoLoad(){
+  return getJSON("/isolation.json").then(function(s){
+    isoAllow=s;
+    if($("isotbl").dataset.dirty)return;
+    s.forEach(function(e){
+      var m=parseInt(e.allow,16);
+      for(var c=1;c<=S.n;c++){var b=isoBox(e.portNum,c);if(b)b.checked=!!((m>>S.physToLog[c-1])&1);}
+      var cpu=isoBox(e.portNum,S.n+1);
+      if(cpu)cpu.checked=!!(m&0x200);
+    });
+    isoMark();
+  });
+}
+function isoMask(r){
+  var m=0;
+  for(var c=1;c<=S.n;c++){var b=isoBox(r,c);if(r===c||(b&&b.checked))m|=1<<S.physToLog[c-1];}
+  var cpu=isoBox(r,S.n+1);
+  if(cpu&&cpu.checked)m|=0x200;
+  return m;
+}
+$("isoapply").addEventListener("click",function(){
+  var cmds=[];
+  for(var r=1;r<=S.n;r++){
+    var cur=-1;
+    isoAllow.forEach(function(e){if(e.portNum===r)cur=parseInt(e.allow,16)});
+    if(isoMask(r)===cur)continue;
+    var cmd="isolate "+r;
+    for(var c=1;c<=S.n;c++){var b=isoBox(r,c);if(r===c||(b&&b.checked))cmd+=" "+c;}
+    var cpu=isoBox(r,S.n+1);
+    if(cpu&&cpu.checked)cmd+=" 0";
+    cmds.push(cmd);
+  }
+  delete $("isotbl").dataset.dirty;
+  if(!cmds.length){isoLoad().catch(function(){});return;}
+  postCmds(cmds).then(isoLoad).catch(function(){});
+});
+$("isoall").addEventListener("click",function(){
+  for(var r=1;r<=S.n;r++)for(var c=1;c<=S.n+1;c++){var b=isoBox(r,c);if(b)b.checked=true;}
+  isoTouch();
+});
+tabHooks.isolate={enter:function(){needPorts(function(){buildIso();isoLoad().catch(function(){})})}};
+
 var HASHF=["spa","smac","dmac","sip","dip","sport","dport"];
 function buildLag(){
   var w=$("lagwrap");
@@ -1523,6 +1838,32 @@ function lagApply(g){
 }
 tabHooks.lag={enter:function(){needPorts(function(){buildLag();lagLoad().catch(function(){})})}};
 
+
+function lldpLoad(){
+  return getJSON("/lldp.json").then(function(s){
+    $("lldp_en").checked=s.on;
+    var tb=$("lldp_table").tBodies[0];tb.innerHTML="";
+    byPort(s.portStatus).forEach(function(p){
+      var tr=tb.insertRow();
+      tr.insertCell().textContent=p.portNum;
+      tr.insertCell().textContent=p.name;
+      var sw=h("label",{class:"switch"},[
+        h("input",{type:"checkbox",onchange:function(){
+          postCmd("port "+p.portNum+" lldp "+(this.checked?"permit":"block"))
+            .then(function(){setTimeout(lldpLoad,300)}).catch(function(){});
+        }}),h("i")]);
+      sw.firstChild.checked=p.permitted;
+      tr.insertCell().appendChild(sw);
+    });
+  });
+}
+
+$("lldp_en").addEventListener("change",function(){
+  var el=this;
+  postCmd("lldp "+(el.checked?"on":"off")).catch(function(){el.checked=!el.checked});
+});
+tabHooks.lldp={enter:lldpLoad};
+
 function eeeFlags(bits){
   var b=parseInt(bits,2);
   return["100M","1G","2.5G"].map(function(s,i){
@@ -1608,7 +1949,61 @@ function bwApply(n){
   }else cmds.push("bw out "+n+" off");
   postCmds(cmds).then(bwLoad).catch(function(){});
 }
-tabHooks.bw={enter:function(){needPorts(function(){bwLoad().catch(function(){})})}};
+var SC_TYPES=["bcast","mcast","ucast","umcast"],scSig="";
+function scLoad(){
+  return getJSON("/storm.json").then(function(s){
+    var tb=$("sctable").tBodies[0];
+    byPort(s);
+    var sig=s.map(function(p){return p.portNum}).join();
+    if(sig!==scSig){
+      scSig=sig;tb.innerHTML="";
+      s.forEach(function(p){
+        var n=p.portNum,tr=tb.insertRow();
+        tr.id="scr"+n;
+        tr.addEventListener("input",function(){tr.dataset.dirty="1"});
+        tr.addEventListener("change",function(){tr.dataset.dirty="1"});
+        tr.insertCell().textContent=n;
+        SC_TYPES.forEach(function(ty){
+          tr.insertCell().appendChild(h("span",{style:"display:flex;gap:4px"},[
+            h("input",{class:"in sm",id:"scv"+ty+n,type:"number",min:"1",step:"1"}),
+            h("select",{class:"in",id:"scu"+ty+n},[
+              h("option",{value:"pps",text:"pps"}),
+              h("option",{value:"kbps",text:"kbit/s"}),
+            ]),
+          ]));
+        });
+        tr.insertCell().appendChild(h("button",{class:"ctl",text:t("c_apply"),onclick:function(){scApply(n)}}));
+      });
+    }
+    s.forEach(function(p){
+      var n=p.portNum;
+      if($("scr"+n).dataset.dirty)return;
+      SC_TYPES.forEach(function(ty,k){
+        var on=p.en.charAt(k)==="1",pps=p.pps.charAt(k)==="1",raw=parseInt(p.rate.substr(k*6,6),16);
+        var inp=$("scv"+ty+n),sel=$("scu"+ty+n);
+        inp.value=on?raw:"";
+        sel.value=on&&!pps?"kbps":"pps";
+        inp.dataset.cur=on?inp.value+" "+sel.value:"off";
+      });
+    });
+  });
+}
+function scApply(n){
+  var cmds=[];
+  for(var k=0;k<SC_TYPES.length;k++){
+    var ty=SC_TYPES[k],inp=$("scv"+ty+n),u=$("scu"+ty+n).value,v=inp.value.trim(),want="off";
+    if(v!==""&&v!=="0"){
+      var x=Number(v);
+      if(!Number.isInteger(x)||x<1||(u==="pps"&&x>1048575)||(u==="kbps"&&x>10000000)){toast(t("sc_err"),"err");return;}
+      want=x+" "+u;
+    }
+    if(want!==inp.dataset.cur)cmds.push("storm "+n+" "+ty+" "+want);
+  }
+  delete $("scr"+n).dataset.dirty;
+  if(!cmds.length)return;
+  postCmds(cmds).then(scLoad).catch(function(){});
+}
+tabHooks.bw={enter:function(){needPorts(function(){bwLoad().then(scLoad).catch(function(){})})}};
 
 var IPRE=/^(\d{1,3}\.){3}\d{1,3}$/;
 function okIp(s){
@@ -1624,6 +2019,7 @@ function sysLoad(){
     var sl=(S.info.syslog_server||"").split(":");
     if(sl[0]&&sl[0]!=="0.0.0.0")$("sy-sysip").value=sl[0];
     if(sl[1])$("sy-sysport").value=sl[1];
+    if(S.info.session_timeout)$("sy-sesstmo").value=S.info.session_timeout;
   }).catch(function(){});
   cfgReload();
 }
@@ -1648,7 +2044,7 @@ $("sy-apply").addEventListener("click",function(){
     if(!/^[\x21-\x7e]{1,23}$/.test(hn)||/["\\]/.test(hn)){toast(t("sy_host_err"),"err");return;}
     cmds.push("hostname "+hn);
   }
-  cmds.push("ip "+ip,"netmask "+mask,"gw "+gw);
+  cmds.push("ip "+ip+"\nnetmask "+mask+"\ngw "+gw);
   var changingIp=ip!==S.info.ip_address;
   confirmModal(t("sy_net_q"),changingIp?t("sy_net_d",{ip:ip}):"",function(){
     postCmds(cmds).then(function(){
@@ -1676,6 +2072,11 @@ $("sy-syslog").addEventListener("change",function(){
   }else cmds.push("syslog off");
   postCmds(cmds).catch(function(){});
 });
+$("sy-sesstmo").addEventListener("change",function(){
+  var v=+this.value;
+  if(!(v>=1&&v<=65535)){toast(t("sy_sesstmo_err"),"err");sysLoad();return;}
+  postCmd("session "+v).catch(function(){sysLoad()});
+});
 $("sy-pwapply").addEventListener("click",function(){
   var a=$("sy-pw1").value,b=$("sy-pw2").value;
   if(a.length<1||a.length>20){toast(t("sy_pw_len"),"err");return;}
@@ -1739,7 +2140,7 @@ tabHooks.system={enter:sysLoad};
 
 var CONF_OVERWRITE=[
   /^ip\b/,/^gw\b/,/^netmask\b/,/^hostname\b/,
-  /^syslog\s+ip\b/,/^syslog\s+port\b/,/^passwd\b/,
+  /^syslog\s+ip\b/,/^syslog\s+port\b/,/^passwd\b/,/^session\b/,
   /^vlan\s+\d{1,4}\s+mgmt$/,/^vlan\s+\d{1,4}(?!\s+mgmt\b)/,
   /^pvid\s+\d{1,2}\b/,
   /^port\s+\d{1,2}(?!\s+name\b)/,/^port\s+\d{1,2}\s+name\b/,
@@ -1747,7 +2148,7 @@ var CONF_OVERWRITE=[
   /^lag\s+\d\b/,/^laghash\s+\d\b/,/^isolate\s+\d{1,2}\b/,
   /^stp\s+(prio|hello|maxage|fwd|txhold|version)\b/,
   /^stp\s+(port\s+\d{1,2}|lag\s+[1-4])\s+(edge|cost|prio|guard|filter|p2p)\b/,
-  /^igmp\b/,/^mtu\s+\d{1,2}\b/,
+  /^igmp\b/,/^mtu\s+\d{1,2}\b/,/^storm\s+\d{1,2}\s+(bcast|mcast|ucast|umcast)\b/,
 ];
 var CONF_TOGGLE=[/^(syslog)\s+(on|off)$/,/^(stp)\s+(on|off)$/,/^(stp\s+(port\s+\d{1,2}|lag\s+[1-4]))\s+(on|off)$/];
 function mergeConf(base,texts){

html/index.html

@@ -331,6 +331,29 @@ button.danger{background:var(--bad);color:#fff;border-color:transparent}
       </div>
     </section>
 
+    <section class="tab" id="tab-lldp">
+      <div class="card"><h2 data-i18n="lldp_title">LLDP</h2>
+        <label class="row"><span class="lb" data-i18n="lldp_enabled">Enabled</span>
+          <span class="switch"><input type="checkbox" id="lldp_en"><i></i></span>
+        </label>
+        <div class="scrollx"><table class="t" id="lldp_table">
+          <thead><tr><th data-i18n="c_port">Port Number</th><th data-i18n="lldp_portname">Name</th><th data-i18n="lldp_enable">Send Frames</th></tr></thead>
+          <tbody></tbody></table></div>
+      </div>
+    </section>
+
+    <section class="tab" id="tab-isolate">
+      <div class="card"><h2 data-i18n="iso_title">Port isolation</h2>
+        <p class="small mut" style="margin-bottom:10px" data-i18n="iso_intro">A frame entering a port may only leave through the ports ticked in its row.</p>
+        <div class="scrollx"><table class="t" id="isotbl" style="width:auto"><thead></thead><tbody></tbody></table></div>
+        <p class="small mut" style="margin-top:6px" data-i18n="iso_legend">The cell of the port itself is always allowed.</p>
+        <div style="display:flex;gap:12px;margin-top:10px">
+          <button class="ctl pri" id="isoapply" data-i18n="c_apply">Apply</button>
+          <button class="ctl" id="isoall" data-i18n="iso_all">Allow all</button>
+        </div>
+      </div>
+    </section>
+
     <section class="tab" id="tab-lag">
       <div id="lagwrap" class="grid2"></div>
       <p class="small mut" style="margin-top:10px" data-i18n="lag_note">A LAG needs at least one member to be saved in the startup config; applying an empty group clears it.</p>
@@ -351,6 +374,12 @@ button.danger{background:var(--bad);color:#fff;border-color:transparent}
           <thead><tr><th data-i18n="c_port">Port</th><th data-i18n="bw_in">Ingress limit</th><th>Mbit/s</th><th data-i18n="bw_exceed">When exceeded</th><th data-i18n="bw_out">Egress limit</th><th>Mbit/s</th><th></th></tr></thead>
           <tbody></tbody></table></div>
       </div>
+      <div class="card"><h2><span data-i18n="sc_title">Storm control</span> <span class="hint" data-i18n="sc_h">per port and traffic type, empty = off</span></h2>
+        <div class="scrollx"><table class="t" id="sctable">
+          <thead><tr><th data-i18n="c_port">Port</th><th data-i18n="sc_bcast">Broadcast</th><th data-i18n="sc_mcast">Multicast</th><th data-i18n="sc_ucast">Unknown unicast</th><th data-i18n="sc_umcast">Unknown multicast</th><th></th></tr></thead>
+          <tbody></tbody></table></div>
+        <p class="small mut" style="margin-top:8px" data-i18n="sc_note">Frames of a type above its limit are dropped where they enter the switch.</p>
+      </div>
     </section>
 
     <section class="tab" id="tab-system">
@@ -375,6 +404,8 @@ button.danger{background:var(--bad);color:#fff;border-color:transparent}
             <input class="in" id="sy-sysip" style="flex:1;min-width:0;width:0" data-i18n-p="sy_sysip">
             <span class="small mut" data-i18n="sy_port">Port</span>
             <input class="in" id="sy-sysport" style="width:64px" type="number" min="1" max="65535"></div>
+          <label class="row" style="justify-content:space-between"><span data-i18n="sy_sesstmo">Session timeout (s)</span>
+            <input class="in" id="sy-sesstmo" style="width:80px" type="number" min="1" max="65535"></label>
           <p class="small mut" data-i18n="sy_services_note">Service state reflects the startup config; runtime state is not readable.</p>
         </div>
         <div class="card"><h2 data-i18n="sy_password">Admin password</h2>
@@ -393,10 +424,13 @@ button.danger{background:var(--bad);color:#fff;border-color:transparent}
         <div class="card"><h2 data-i18n="sy_display">Display</h2>
           <label class="row"><span class="lb" data-i18n="sy_lang">Language</span>
             <select class="in" id="langSel">
+              <option value="de">Deutsch</option>
               <option value="en">English</option>
+              <option value="es">Español</option>
+              <option value="fr">Français</option>
               <option value="ja">日本語</option>
               <option value="zh">中文</option>
-              <option value="es">Español</option>
+              
             </select></label>
           <label class="row"><span class="lb" data-i18n="sy_theme">Theme</span>
             <select class="in" id="themeSel">

html/login.html

@@ -81,10 +81,12 @@ button:hover{filter:brightness(1.1)}
 <script>
 (function(){
   var L={
+    de:["Switch-Anmeldung","RTLPlayground-Verwaltungsoberfläche","Passwort","Anmelden","Falsches Passwort, bitte erneut versuchen."],
     en:["Switch Login","RTLPlayground management interface","Password","Sign in","Wrong password, try again."],
     ja:["スイッチ ログイン","RTLPlayground 管理インターフェース","パスワード","ログイン","パスワードが違います。もう一度お試しください。"],
     zh:["交换机登录","RTLPlayground 管理界面","密码","登录","密码错误，请重试。"],
-    es:["Inicio de sesión del switch","Interfaz de gestión de RTLPlayground","Contraseña","Iniciar sesión","Contraseña incorrecta, inténtalo de nuevo."]
+    es:["Inicio de sesión del switch","Interfaz de gestión de RTLPlayground","Contraseña","Iniciar sesión","Contraseña incorrecta, inténtalo de nuevo."],
+    fr:["Utilisateur du commutateur","Interface de management RTLPlayground","Mot de passe","Se connecter","Mot de passe erronné, essayez à nouveau."]
   };
   var l=null;
   try{l=localStorage.getItem("rtl_lang");}catch(e){}

httpd/httpd.c

@@ -12,7 +12,11 @@
 #include "debug.h"
 
 #define SESSION_ID_LENGTH 12
-#define SESSION_TIMEOUT 200
+#define SESSION_TIMEOUT_DEFAULT 200
+
+/* Seconds of inactivity after which a session cookie stops validating.
+ * Configurable with the "session" command, see cmd_parser.c. */
+__xdata uint16_t session_timeout = SESSION_TIMEOUT_DEFAULT;
 
 #define CMARK_S 6
 
@@ -342,7 +346,7 @@ __xdata uint8_t *scan_header(__xdata uint8_t * __xdata p)
 	read_reg_timer(&now);
 
 	if (session && session_id[0]) {
-		if (now - last_session_use > SESSION_TIMEOUT) {
+		if (now - last_session_use > session_timeout) {
 			dbg_string("Session expired\n");
 		} else {
 			if (is_word_x(session, session_id)) {
@@ -1012,6 +1016,8 @@ void httpd_appcall(void)
 				send_eee();
 			} else if (is_word(q, "/bandwidth.json")) {
 				send_bandwidth();
+			} else if (is_word(q, "/storm.json")) {
+				send_storm();
 			} else if (is_word(q, "/l2.json")) {
 				parse_short(q + 13); // e.g.: /l2.json?idx=10
 				send_l2(short_parsed);
@@ -1020,12 +1026,16 @@ void httpd_appcall(void)
 				l2_delete(short_parsed);
 			} else if (is_word(q, "/mirror.json")) {
 				send_mirror();
+			} else if (is_word(q, "/isolation.json")) {
+				send_isolation();
 			} else if (is_word(q, "/mtu.json")) {
 				send_mtu();
 			} else if (is_word(q, "/lag.json")) {
 				send_lag();
 			} else if (is_word(q, "/stp.json")) {
 				send_stp();
+			} else if (is_word(q, "/lldp.json")) {
+				send_lldp();
 			} else if (is_word(q, "/vlanlist")) {
 				send_vlanlist();
 			} else if (is_word(q, "/config")) {

httpd/page_impl.c

@@ -3,6 +3,7 @@
 #include "rtl837x_sfr.h"
 #include "rtl837x_common.h"
 #include "rtl837x_regs.h"
+#include "rtl837x_storm.h"
 #include "rtl837x_port.h"
 #include "rtl837x_flash.h"
 #include "rtl837x_pins.h"
@@ -28,6 +29,7 @@ extern __code const struct machine machine;
 extern __xdata uint8_t outbuf[TCP_OUTBUF_SIZE];
 extern __xdata uint16_t slen;
 extern __xdata uint16_t management_vlan;
+extern __xdata uint16_t session_timeout;
 extern __xdata uint16_t cont_len;
 extern __xdata uint32_t cont_addr;
 extern __code const uint8_t * __code const hex;
@@ -47,6 +49,9 @@ extern __xdata char sfp_module_model[2][17];
 extern __xdata char sfp_module_serial[2][17];
 extern __xdata uint8_t sfp_options[2];
 
+extern __xdata uint16_t lldp_logical_port_status;
+extern __xdata bool lldp_enabled;
+
 __code const uint8_t * __code const HTTP_RESPONCE_JSON = "HTTP/1.1 200 OK\r\nConnection: close\r\nContent-Type: application/json\r\n\r\n";
 __code const uint8_t * __code const HTTP_RESPONCE_TXT = "HTTP/1.1 200 OK\r\nConnection: close\r\nContent-Type: text/plain\r\n\r\n";
 
@@ -114,12 +119,14 @@ void itoa_html(uint8_t v)
 	char_to_html('0' + (v % 10));
 }
 
-void itoa16_html(uint16_t v) /* sufficient for VLAN IDs (max 4094) */
+void itoa16_html(uint16_t v) /* up to five digits (65535) */
 {
 	uint8_t print_zeros = 0;
 	uint8_t d;
-	d = v / 1000;
+	d = v / 10000;
 	if (d) { char_to_html('0' + d); print_zeros = 1; }
+	d = (v / 1000) % 10;
+	if (d || print_zeros) { char_to_html('0' + d); print_zeros = 1; }
 	d = (v / 100) % 10;
 	if (d || print_zeros) { char_to_html('0' + d); print_zeros = 1; }
 	d = (v / 10) % 10;
@@ -132,6 +139,23 @@ void string_to_html(__code const char *s)
 	while (*s) char_to_html(*s++);
 }
 
+static void temp_to_html(void)
+{
+	int16_t v;
+
+	reg_read(RTL837X_TM_RESULT);
+	v = SFR_DATA_U16;
+	if (v < 0) {
+		char_to_html('-');
+		v = -v;
+	}
+	itoa_html(v >> 7);
+	char_to_html('.');
+	itoa_html(((v & 0x7f) * 10) >> 7);
+	char_to_html(' ');
+	char_to_html('C');
+}
+
 uint16_t stat_content(void)
 {
 	dbg_string("stat_content called\n");
@@ -258,7 +282,9 @@ void send_basic_info(void)
 	itoa_html(syslog_state.server_ip[2]); char_to_html('.');
 	itoa_html(syslog_state.server_ip[3]); char_to_html(':');
 	itoa16_html(syslog_state.server_port);
-	slen += strtox(outbuf + slen, "\",\"mac_address\":\"");
+	slen += strtox(outbuf + slen, "\",\"session_timeout\":");
+	itoa16_html(session_timeout);
+	slen += strtox(outbuf + slen, ",\"mac_address\":\"");
 	byte_to_html(uip_ethaddr.addr[0]); char_to_html(':');
 	byte_to_html(uip_ethaddr.addr[1]); char_to_html(':');
 	byte_to_html(uip_ethaddr.addr[2]); char_to_html(':');
@@ -277,6 +303,8 @@ void send_basic_info(void)
 	slen += strtox(outbuf + slen, BUILD_DATE);
 	slen += strtox(outbuf + slen, "\",\"hw_ver\":\"");
 	slen += strtox(outbuf + slen, machine.machine_name);
+	slen += strtox(outbuf + slen, "\",\"chip_temp\":\"");
+	temp_to_html();
 	slen += strtox(outbuf + slen, "\",\"flash_size\":\"");
 	string_to_html(get_flash_size_str());
 
@@ -594,7 +622,6 @@ static void bridge_to_html(void)
 		byte_to_html(pi_mac[i]);
 }
 
-
 void send_stp(void)
 {
 	uint8_t i, j, st, dsg;
@@ -709,8 +736,37 @@ void send_stp(void)
 	slen += strtox(outbuf + slen, "]}");
 }
 
+void send_lldp(void)
+{
+	dbg_string("send_lldp called\n");
+	slen = strtox(outbuf, HTTP_RESPONCE_JSON);
 
+	slen += strtox(outbuf + slen, "{\"on\":");
+	bool_to_html(lldp_enabled);
+	slen += strtox(outbuf + slen, ",\"portStatus\":[");
 
+	for (uint8_t i = machine.min_port; i <= machine.max_port; i++) {
+		slen += strtox(outbuf + slen, "{\"portNum\":");
+		itoa_html(machine.log_to_phys_port[i]);
+
+		slen += strtox(outbuf + slen, ",\"logPort\":");
+		itoa_html(i);
+		slen += strtox(outbuf + slen, ",\"name\":\"");
+		for (uint8_t j = 0; j < PORT_NAME_SIZE && port_names[i][j]; j++) {
+			json_char_to_html(port_names[i][j]);
+		}
+
+		slen += strtox(outbuf + slen, "\",\"permitted\":");
+		bool_to_html(1 & (lldp_logical_port_status >> i));
+		slen += strtox(outbuf + slen, "}");
+
+		if (i < machine.max_port)
+			char_to_html(',');
+		else
+			char_to_html(']');
+	}
+	char_to_html('}');
+}
 
 void send_eee(void)
 {
@@ -804,6 +860,63 @@ void send_bandwidth(void)
 }
 
 
+void send_storm(void)
+{
+	__xdata uint8_t i, t, idx;
+
+	slen = strtox(outbuf, HTTP_RESPONCE_JSON);
+	char_to_html('[');
+	for (i = machine.min_port; i <= machine.max_port; i++) {
+		slen += strtox(outbuf + slen, "{\"portNum\":");
+		itoa_html(machine.log_to_phys_port[i]);
+		slen += strtox(outbuf + slen, ",\"en\":\"");
+		for (t = 0; t < STORM_TYPES; t++)
+			char_to_html(reg_bit_test(RTL837X_STORM_CTRL + (t << 2), i) ? '1' : '0');
+		slen += strtox(outbuf + slen, "\",\"pps\":\"");
+		for (t = 0; t < STORM_TYPES; t++) {
+			idx = STORM_METER(i, t);
+			char_to_html(reg_bit_test(RTL837X_METER_MODE + ((idx >> 5) << 2), idx & 0x1f) ? '1' : '0');
+		}
+		slen += strtox(outbuf + slen, "\",\"rate\":\"");
+		for (t = 0; t < STORM_TYPES; t++) {
+			reg_read_m(RTL837X_METER_RATE + (STORM_METER(i, t) << 2));
+			byte_to_html(sfr_data[1]);
+			byte_to_html(sfr_data[2]);
+			byte_to_html(sfr_data[3]);
+		}
+		char_to_html('"');
+		char_to_html('}');
+		if (i < machine.max_port)
+			char_to_html(',');
+		else
+			char_to_html(']');
+	}
+}
+
+
+void send_isolation(void)
+{
+	__xdata uint16_t allow;
+
+	dbg_string("send_isolation called\n");
+	slen = strtox(outbuf, HTTP_RESPONCE_JSON);
+	char_to_html('[');
+	for (uint8_t i = machine.min_port; i <= machine.max_port; i++) {
+		slen += strtox(outbuf + slen, "{\"portNum\":");
+		itoa_html(machine.log_to_phys_port[i]);
+		slen += strtox(outbuf + slen, ",\"allow\":\"");
+		allow = port_isolation_get(i);
+		byte_to_html(allow >> 8);
+		byte_to_html(allow & 0xff);
+		char_to_html('"');
+		char_to_html('}');
+		if (i < machine.max_port)
+			char_to_html(',');
+	}
+	char_to_html(']');
+}
+
+
 void send_mtu(void)
 {
 	dbg_string("send_mtu called\n");
@@ -1036,8 +1149,7 @@ void send_vlanlist(void)
 	slen += strtox(outbuf + slen, ",\"vlan\":[");
 
 	for (i = 1; i < 4095; i++) {
-		if (vlan_get(i) < 0)
-			continue;
+		vlan_get(i);
 		if (!(sfr_data[0] & 0x02)) /* bit 1: VLAN table entry valid */
 			continue;
 

httpd/page_impl.h

@@ -5,20 +5,25 @@
 
 extern __code const uint8_t * __code const HTTP_RESPONCE_TXT;
 
+void itoa16_html(uint16_t v);
+
 bool send_counters(uint8_t phys_port);
 void send_status(void);
 void send_vlan(uint16_t vlan);
 void send_basic_info(void);
 void send_bandwidth(void);
+void send_storm(void);
 void send_eee(void);
 void send_l2(uint16_t idx);
 void l2_delete(uint16_t idx);
 void send_mirror(void);
 void send_mtu(void);
+void send_isolation(void);
 void send_config(void);
 void send_cmd_log(void);
 void send_lag(void);
 void send_stp(void);
+void send_lldp(void);
 void send_vlanlist(void);
 
 /*  Convert only the lower nibble to ascii HEX char.

machine.c

@@ -237,9 +237,14 @@ __code const struct machine machine = {
 	},
 };
 
-#elif defined MACHINE_KP_9000_9XHML_X_V3_1
+#elif defined(MACHINE_KP_9000_9XHML_X_V3_1) || defined(MACHINE_KP_9000_9XHML_X_V3_2)
+// 2M-PCB23-V3.2 is wired like V3.1 (SFP detection, LEDs, factory MAC location)
 __code const struct machine machine = {
+#if defined(MACHINE_KP_9000_9XHML_X_V3_2)
+	.machine_name = "keepLink KP-9000-9XHML-X V3.2",
+#else
 	.machine_name = "keepLink KP-9000-9XHML-X V3.1",
+#endif
 	.isRTL8373 = 1,
 	.min_port = 0,
 	.max_port = 8,
@@ -930,6 +935,68 @@ __code const struct machine machine = {
             },
     };
 
+#elif defined MACHINE_ONT_S207CW_62TS_SE
+
+__code const struct machine machine = {
+    .machine_name = "ONT-S207CW-62TS-SE / Binardat 2G06-04210GSM / Binardat 2G06-04210GS",
+    .isRTL8373 = 0,
+    .min_port = 3,
+    .max_port = 8,
+    .n_sfp = 2,
+    .log_to_phys_port = {0, 0, 0, 5, 4, 3, 2, 1, 6},
+    .phys_to_log_port = {7, 6, 5, 4, 3, 8, 0, 0, 0},
+    .is_sfp = {0, 0, 0, 1, 0, 0, 0, 0, 2},
+
+    // SFP port on SDS0 / logical port 3
+    .sfp_port[0].pin_detect = GPIO37,
+    .sfp_port[0].pin_los = GPIO_NA,
+    .sfp_port[0].pin_tx_disable = GPIO_NA,
+    .sfp_port[0].sds = 0,
+    .sfp_port[0].i2c = I2CBUS( GPIO41_I2C_SDA3_MDIO1, GPIO40_I2C_SCL3_MDC1 ),
+
+    // SFP port on SDS1 / logical port 8
+    .sfp_port[1].pin_detect = GPIO38,
+    .sfp_port[1].pin_los = GPIO_NA,
+    .sfp_port[1].pin_tx_disable = GPIO_NA,
+    .sfp_port[1].sds = 1,
+    .sfp_port[1].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
+
+    .reset_pin = GPIO_NA,
+    .high_leds = { .mux =  LED_28_SYS | LED_29, .enable = LED_27 | LED_28_SYS | LED_29 },
+    .port_led_set = { 0, 0, 0, 3, 0, 0, 2, 2, 3},
+    .mac_flash_offset = 0x1FC000,
+    .led_sets = {
+        { // RJ45 Ports 3-4 (normal wiring)
+            LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
+            LEDS_2G5 | LEDS_LINK | LEDS_ACT,
+            0,
+            0
+        },
+        { // Unused
+            0,
+            0,
+            0,
+            0
+        },
+        { // RJ45 Ports 1-2 (reversed wiring)
+            LEDS_2G5 | LEDS_LINK | LEDS_ACT,
+            LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
+            0,
+            0
+        },
+        { // SFP Ports 5-6
+            LEDS_10G | LEDS_LINK | LEDS_ACT,
+            LEDS_2G5 | LEDS_1G | LEDS_LINK | LEDS_ACT,
+            0,
+            0
+        },
+    },
+    .led_mux_custom = 1,
+    .led_mux = {
+        0x00,0x01,0x04,0x05,0x08,0x09,0x0c,0x3f,0x0d,0x10,0x11,0x0e,0x14,0x11,0x12,0x15,0x15,0x16,0x18,0x19,0x1a,0x19,0x1d,0x1e,0x1c,0x1d,0x20,0x21
+    },
+};
+
 #elif defined MACHINE_SWTG024AS_A_2_0_1_5C_1SFP
 __code const struct machine machine = {
     .machine_name = "SWTG024AS-A-V2.0.1-5C-1SFP",
@@ -1325,6 +1392,37 @@ __code const struct machine machine = {
     },
 
 };
+#elif defined MACHINE_HASIVO_S1100WP_8GT_1SX_SE
+__code const struct machine machine = {
+	.machine_name = "Hasivo S1100WP-8GT-1SX-SE",
+	.isRTL8373 = 1,
+	.mac_flash_offset = 0x1FC000,
+	.min_port = 0,
+	.max_port = 8,
+	.n_sfp = 1,
+	.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
+	.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
+	.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
+	.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
+	.sfp_port[0].pin_los = GPIO37,
+	.sfp_port[0].pin_tx_disable = GPIO_NA,
+	.sfp_port[0].sds = 1,
+	.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
+	.reset_pin = GPIO54_ACL_BIT2_EN,
+	.high_leds = { .mux = LED_27 | LED_28_SYS | LED_29, .enable = LED_28_SYS | LED_29 },
+	.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1},
+	.led_sets = { { LEDS_2G5 | LEDS_LINK | LEDS_ACT, // Green LED (right)
+					0,
+					LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT, // Amber LED (left)
+					0
+				  },
+				  { LEDS_10G | LEDS_5G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_LINK | LEDS_ACT, // SFP LED
+					0, 
+					0,
+					0
+				  },
+				},
+};
 #elif defined MACHINE_F7008_2_5
 __code const struct machine machine = {
 	.machine_name = "F7008-2.5 8+1 SFP Port Switch",

machine.h

@@ -22,6 +22,7 @@
 // #define MACHINE_KP_9000_9XH_X_EU
 // #define MACHINE_KP_9000_9XHML_X_V2_2
 // #define MACHINE_KP_9000_9XHML_X_V3_1
+// #define MACHINE_KP_9000_9XHML_X_V3_2
 // #define MACHINE_SWGT024_V2_0_MANAGED
 // #define MACHINE_SWGT024_V2_0_UNMANAGED
 // #define MACHINE_TRENDNET_TEG_S562
@@ -40,6 +41,7 @@
 // #define MACHINE_HI_K0801WS
 // #define MACHINE_FNS1200P
 // #define MACHINE_PCB_SWTG024AS_A_2_0_1
+// #define MACHINE_ONT_S207CW_62TS_SE
 // #define MACHINE_SWTG024AS_A_2_0_1_5C_1SFP
 // #define MACHINE_SWTG024AS_V2_0
 // #define MACHINE_FG_4GT_2SX_V2_0
@@ -48,6 +50,7 @@
 // #define MACHINE_POE_2G080110GS
 // #define MACHINE_PB_2132
 // #define MACHINE_HASIVO_S600W_4GT_2XGT_SE
+// #define MACHINE_HASIVO_S1100WP_8GT_1SX_SE
 // #define MACHINE_F7008_2_5
 
 #define LED_27 1

machine_init.c

@@ -15,7 +15,11 @@
 
 #if defined(MACHINE_KP_9000_6XH_X2) || \
 	defined(MACHINE_KP_9000_6XH_X2_V2_1) || \
-	defined(MACHINE_KP_9000_6XHML_X2_V2_1)
+	defined(MACHINE_KP_9000_6XHML_X2_V2_1) || \
+	defined(MACHINE_HI_K0402WS) || \
+	defined(MACHINE_PCB_K0402WS_V2) || \
+	defined(MACHINE_PCB_K0402WS_V3) || \
+	defined(MACHINE_FNS1200P)
 void machine_custom_init(void) __banked
 {
 	reg_bit_set(RTL837X_REG_LED_GLB_IO_EN, 6);
@@ -42,18 +46,6 @@ void machine_custom_init(void) __banked
 	}
 }
 
-#elif defined(MACHINE_PCB_K0402WS_V3) || defined(MACHINE_HI_K0402WS)
-void machine_custom_init(void) __banked
-{
-	reg_bit_set(RTL837X_REG_LED_GLB_IO_EN, 6);
-}
-
-#elif defined(MACHINE_PCB_K0402WS_V2) || defined(MACHINE_FNS1200P)
-void machine_custom_init(void) __banked
-{
-    reg_bit_set(RTL837X_REG_LED_GLB_IO_EN, 6);
-}
-
 #elif defined MACHINE_PCB_SWTG024AS_A_2_0_1
 void machine_custom_init(void) __banked
 {
@@ -63,27 +55,8 @@ void machine_custom_init(void) __banked
     reg_bit_clear(RTL837X_REG_LED_MODE, 7);
 }
 
-#elif defined MACHINE_SWTG024AS_A_2_0_1_5C_1SFP
-void machine_custom_init(void) __banked
-{
-    uint16_t pval;
-
-    reg_bit_set(RTL837X_REG_LED_GLB_IO_EN, 6);
-    reg_bit_set(RTL837X_REG_LED_MODE, 17);
-    reg_bit_clear(RTL837X_REG_LED_MODE, 9);
-    reg_bit_clear(RTL837X_REG_LED_MODE, 7);
-
-    // OEM firmware sets these companion SDS0 polarity bits for the RTL8221B.
-    sds_read(0, 0, 0);
-    pval = SFR_DATA_U16;
-    sds_write_v(0, 0, 0, pval | 0x100);
-
-    sds_read(0, 6, 2);
-    pval = SFR_DATA_U16;
-    sds_write_v(0, 6, 2, pval | 0x4000);
-}
-
-#elif defined MACHINE_SWTG024AS_V2_0
+#elif defined(MACHINE_SWTG024AS_A_2_0_1_5C_1SFP) || \
+      defined(MACHINE_SWTG024AS_V2_0)
 void machine_custom_init(void) __banked
 {
     uint16_t pval;

rtl837x_common.h

@@ -7,6 +7,14 @@
 
 #define SYS_TICK_HZ 200
 
+/* Timers of the main loop count system ticks, not loop passes: a pass is as
+ * long as the packets it handles, and since #483 the loop no longer sleeps
+ * while packets wait, so passes can outrun the tick as well as lag it. `last`
+ * is the low byte of ticks when the timer last ran; the byte arithmetic wraps
+ * every 256 ticks, so a pass longer than 1.28 s loses time rather than
+ * running the timer 64 times to catch up. */
+#define TICKS_DUE(last, period)	((uint8_t)((uint8_t)ticks - (last)) >= (period))
+
 #define CPU_PORT        9
 #define NUL			'\0'
 
@@ -123,6 +131,7 @@ struct flash_region_t {
 };
 
 extern __xdata char port_names[9][PORT_NAME_SIZE];
+extern __xdata uint16_t lldp_logical_port_status;
 
 extern __xdata bool stp_enabled;
 

rtl837x_igmp.c

@@ -9,6 +9,7 @@
 #define IPMC_USES_L3MC
 
 #include <stdint.h>
+#include <stddef.h>
 #include "rtl837x_common.h"
 #include "rtl837x_sfr.h"
 #include "rtl837x_regs.h"
@@ -19,6 +20,7 @@ extern __code const struct machine machine;
 extern __xdata uint8_t igmpEnabled;
 
 #include "uip.h"
+#include "uip_arp.h"
 
 #pragma codeseg BANK1
 #pragma constseg BANK1
@@ -29,6 +31,13 @@ extern __xdata struct machine_runtime machine_detected;
 extern __xdata uint8_t uip_buf[UIP_CONF_BUFFER_SIZE + 2];
 
 __xdata uint16_t idx;
+#define IGMP_IP_HDR		offsetof(struct igmp_pkt, hlen)
+#define IGMP_IP_IHL		0x0f
+#define IGMP_GROUP_OFS		4
+#define IGMP_V3_RECORD_OFS	8
+
+static __xdata uint8_t igmp_grp;
+static __xdata uint8_t igmp_join;
 
 #ifdef IPMC_USES_L3MC
 struct ipmc_table_entry {
@@ -198,8 +207,10 @@ void entry_to_l2mc(void)
 #endif
 
 
-void igmp_packet_handler(void) __banked
+uint8_t igmp_packet_handler(void) __banked
 {
+	if (IGMP_I->ipv4_tag != HTONS(UIP_ETHTYPE_IP) || IGMP_I->protocol != IGMP_PROTO)
+		return 0;
 	// By default we do not send anything out
 	uip_len = 0;
 
@@ -211,24 +222,40 @@ void igmp_packet_handler(void) __banked
 	}
 	write_char('\n');
 #endif
-	if (IGMP_I->protocol != 2)
-		return;
+	igmp_grp = IGMP_IP_HDR + ((IGMP_I->hlen & IGMP_IP_IHL) << 2);
 #ifdef DEBUG
-	print_string("Found IGMP, type: "); print_byte(IGMP_I->igmp_type); write_char('\n');
+	print_string("Found IGMP, type: "); print_byte(uip_buf[igmp_grp]); write_char('\n');
 #endif
-	// We react to IGMPv1/v2 and v3 membership reports
-	if (!(IGMP_I->igmp_type == 0x12 || IGMP_I->igmp_type == 0x16 || IGMP_I->igmp_type == 0x22))
-		return;
+	switch (uip_buf[igmp_grp]) {
+	case IGMP_V1_REPORT:
+	case IGMP_V2_REPORT:
+		igmp_join = 1;
+		break;
+	case IGMP_V2_LEAVE:
+		igmp_join = 0;
+		break;
+	case IGMP_V3_REPORT:
+		igmp_grp += IGMP_V3_RECORD_OFS;
+		if (uip_buf[igmp_grp] == IGMP_V3_TO_EXCLUDE)
+			igmp_join = 1;
+		else if (uip_buf[igmp_grp] == IGMP_V3_TO_INCLUDE)
+			igmp_join = 0;
+		else
+			return 1;
+		break;
+	default:
+		return 1;
+	}
+	igmp_grp += IGMP_GROUP_OFS;
 #ifdef DEBUG
-	print_string("IGMP membership report, type "); print_byte(IGMP_I->igmp_rtype); write_char('\n');
+	print_string("IGMP join "); print_byte(igmp_join); write_char('\n');
 #endif
 
 #ifdef IPMC_USES_L3MC
 	memset((__xdata uint8_t *)&entry, 0, sizeof(struct ipmc_table_entry));
 	// For IPv4 MC, the Source-IP is 0.0.0.0
-	entry.sip[0] = 0x00; entry.sip[1] = 0x00; entry.sip[2] = 0x00; entry.sip[3] = 0x00;
 	// For IPv4 MC, the Destination-IP is the IPv4 MC address
-	entry.dip[0] = IGMP_I->mc_ip[0]; entry.dip[1] = IGMP_I->mc_ip[1]; entry.dip[2] = IGMP_I->mc_ip[2]; entry.dip[3] = IGMP_I->mc_ip[3];
+	memcpy(entry.dip, &uip_buf[igmp_grp], sizeof(entry.dip));
 	entry_to_l3mc();
 #else
 	/* The L2 Multicast MAC for IP-Multicast is 01:00:5e:xx:yy:zz, where
@@ -238,7 +265,7 @@ void igmp_packet_handler(void) __banked
 	 */
 	memset((__xdata uint8_t *)&entry, 0, sizeof(struct l2mc_table_entry));
 	entry.mac[0] = 0x01; entry.mac[1] = 0x00; entry.mac[2] = 0x5e;
-	entry.mac[3] = IGMP_I->mc_ip[1] & 0x7f; entry.mac[4] = IGMP_I->mc_ip[2]; entry.mac[5] = IGMP_I->mc_ip[3];
+	entry.mac[3] = uip_buf[igmp_grp + 1] & 0x7f; entry.mac[4] = uip_buf[igmp_grp + 2]; entry.mac[5] = uip_buf[igmp_grp + 3];
 	entry.vlan = 1; //TODO: Get this out of the packet and compare with VLAN table!
 	entry_to_ipmc();
 #endif
@@ -286,7 +313,7 @@ void igmp_packet_handler(void) __banked
 	print_sfr_data();
 #endif
 	idx = ((sfr_data[2] & 0xf) << 8) | sfr_data[3];
-	if (IGMP_I->igmp_rtype == 0x4) {// Join group
+	if (igmp_join) {// Join group
 		if (sfr_data[2] & 0x10) {
 			print_string("\nIGMP-Entry FOUND\n");
 			reg_read_m(RTL837x_L2_DATA_OUT_B);
@@ -297,7 +324,7 @@ void igmp_packet_handler(void) __banked
 		// Update (found) entry with portmask from trapped Packet
 		entry.pmask |= ((uint16_t)1) << ((IGMP_I->rtl_tag.pmask >> 8) & 0x0f);  // Swap bytes from network order, only 4 LSB count
 //		print_string("\nPort-Mask: "); print_short(entry.pmask); write_char('\n');
-	} else if (IGMP_I->igmp_rtype == 0x3){  // Leave group
+	} else {  // Leave group
 		if (sfr_data[2] & 0x10) {
 			print_string("\nIGMP_Entry FOUND\n");
 			reg_read_m(RTL837x_L2_DATA_OUT_B);
@@ -316,7 +343,7 @@ void igmp_packet_handler(void) __banked
 //			print_string("\nPort-Mask: "); print_short(entry.pmask); write_char('\n');
 		} else {
 			print_string("IGMP Entry already deleted\n");
-			return;
+			return 1;
 		}
 		if (!entry.pmask && idx) { // No more ports in that group and an actual entry?
 			// Delete Entry
@@ -328,14 +355,12 @@ void igmp_packet_handler(void) __banked
 				reg_read_m(RTL837X_TBL_CTRL);
 			} while (sfr_data[3] & 0x1);
 			print_string("IGMP Entry deleted\n");
-			return;
+			return 1;
 		}
-	} else {  // Unknown message: ignore.
-		return;
 	}
 
 	if (!entry.pmask)
-		return;
+		return 1;
 	print_string("Updating IGMP entry\n");
 	// Write the updated entry
 #ifdef IPMC_USES_L3MC
@@ -372,4 +397,5 @@ void igmp_packet_handler(void) __banked
 	reg_read_m(RTL837x_TBL_DATA_0);
 	print_sfr_data();
 #endif
+	return 1;
 }

rtl837x_igmp.h

@@ -3,10 +3,18 @@
 
 #include <stdint.h>
 
+#define IGMP_PROTO		2
+#define IGMP_V1_REPORT		0x12
+#define IGMP_V2_REPORT		0x16
+#define IGMP_V2_LEAVE		0x17
+#define IGMP_V3_REPORT		0x22
+#define IGMP_V3_TO_INCLUDE	3
+#define IGMP_V3_TO_EXCLUDE	4
+
 void igmp_setup(void) __banked;
 void igmp_enable(void) __banked;
 void igmp_router_port_set(uint16_t pmask) __banked;
-void igmp_packet_handler(void) __banked;
+uint8_t igmp_packet_handler(void) __banked;
 void igmp_show(void) __banked;
 
 #endif

rtl837x_init.c

@@ -92,8 +92,18 @@ void static sds_init(void)
 }
 
 
+void static tm_init(void)
+{
+	reg_read_m(RTL837X_TM_CTRL2);
+	sfr_mask_data(0, TM_CTRL2_EN_LATCH, 0);
+	reg_write_m(RTL837X_TM_CTRL2);
+}
+
+
 void rtl8373_init(void) __banked
 {
+	tm_init();
+
 	print_string("\nrtl8373_init called\n");
 
 	// r65d8:3ffbedff R65d8-3ffbedff
@@ -191,6 +201,8 @@ void rtl8373_init(void) __banked
 
 void rtl8372_init(void) __banked
 {
+	tm_init();
+
 	print_string("\nrtl8372_init called\n");
 
 	sds_init();

rtl837x_leds.c

@@ -24,149 +24,6 @@ extern __code const struct machine machine;
 
 extern __xdata uint8_t sfr_data[4];
 
-void leds_dump(void) __banked
-{
-	print_string("RTL837X_PIN_MUX_0: "); print_reg(RTL837X_PIN_MUX_0); write_char('\n');
-	print_string("RTL837X_REG_LED_GLB_IO_EN: "); print_reg(RTL837X_REG_LED_GLB_IO_EN); write_char('\n');
-	print_string("RTL837X_REG_LED1_0_SET0: "); print_reg(RTL837X_REG_LED1_0_SET0); write_char('\n');
-	print_string("RTL837X_REG_LED3_2_SET0: "); print_reg(RTL837X_REG_LED3_2_SET0); write_char('\n');
-	print_string("RTL837X_REG_LED1_0_SET1: "); print_reg(RTL837X_REG_LED1_0_SET1); write_char('\n');
-	print_string("RTL837X_REG_LED3_2_SET1: "); print_reg(RTL837X_REG_LED3_2_SET1); write_char('\n');
-	print_string("RTL837X_REG_LED1_0_SET2: "); print_reg(RTL837X_REG_LED1_0_SET2); write_char('\n');
-	print_string("RTL837X_REG_LED3_2_SET2: "); print_reg(RTL837X_REG_LED3_2_SET2); write_char('\n');
-	print_string("RTL837X_REG_LED1_0_SET3: "); print_reg(RTL837X_REG_LED1_0_SET3); write_char('\n');
-	print_string("RTL837X_REG_LED3_2_SET3: "); print_reg(RTL837X_REG_LED3_2_SET3); write_char('\n');
-	print_string("RTL837X_REG_LED3_0_SET1: "); print_reg(RTL837X_REG_LED3_0_SET1); write_char('\n');
-	print_string("RTL837X_REG_LED3_0_SET3: "); print_reg(RTL837X_REG_LED3_0_SET3); write_char('\n');
-	print_string("RTL837X_LED_PORT_SET_SEL: "); print_reg(RTL837X_LED_PORT_SET_SEL); write_char('\n');
-	print_string("RTL837X_REG_LED_GLB_MUX_1: "); print_reg(RTL837X_REG_LED_GLB_MUX_1); write_char('\n');
-	print_string("RTL837X_REG_LED_GLB_MUX_2: "); print_reg(RTL837X_REG_LED_GLB_MUX_2); write_char('\n');
-	print_string("RTL837X_REG_LED_GLB_MUX_3: "); print_reg(RTL837X_REG_LED_GLB_MUX_3); write_char('\n');
-	print_string("RTL837X_REG_LED_GLB_MUX_4: "); print_reg(RTL837X_REG_LED_GLB_MUX_4); write_char('\n');
-	print_string("RTL837X_REG_LED_GLB_MUX_5: "); print_reg(RTL837X_REG_LED_GLB_MUX_5); write_char('\n');
-	print_string("RTL837X_REG_LED_GLB_MUX_6: "); print_reg(RTL837X_REG_LED_GLB_MUX_6); write_char('\n');
-	print_string("RTL837X_REG_LED_GLB_ACTIVE: "); print_reg(RTL837X_REG_LED_GLB_ACTIVE); write_char('\n');
-	print_string("RTL837X_REG_LED_MODE: "); print_reg(RTL837X_REG_LED_MODE); write_char('\n');
-	print_string("LED pad Configuration:\n");
-	for (uint8_t i = 0; i < 28; i++) {
-		print_byte(i);
-		write_char(' ');
-	}
-	write_char('\n');
-	for (uint8_t i = 0; i < 28; i++) {
-		switch (i % 5) {
-		case 0:  // 0
-			reg_read_m(RTL837X_REG_LED_GLB_MUX_1 + (i / 5) * 4);
-			print_byte(sfr_data[3] & 0x3f);
-			break;
-		case 1:  // 6
-			print_byte(((sfr_data[3] >> 6) | (sfr_data[2] << 2)) & 0x3f);
-			break;
-		case 2:  // 12
-			print_byte(((sfr_data[1] << 4) | (sfr_data[2] >> 4)) & 0x3f);
-			break;
-		case 3:  // 18
-			print_byte((sfr_data[1] >> 2) & 0x3f);
-			break;
-		case 4:  // 24
-			print_byte(sfr_data[0] & 0x3f);
-			break;
-		}
-		write_char(' ');
-	}
-	write_char('\n');
-	print_string("LED-set Configuration:\n");
-	print_string("LED-ID\t\t0\t\t1\t\t2\t\t3\n");
-	for (__xdata uint8_t set = 0; set < 4; set++) {
-		print_string("SET "); write_char('0' + set); write_char(':');
-		for (__xdata uint8_t ledid = 0; ledid < 4; ledid++) {
-			print_string("\t   ");
-			uint8_t b;
-			if (set < 2) {
-				reg_read_m(RTL837X_REG_LED3_0_SET1);
-				b = sfr_data[3-((set << 1) + (ledid >> 1))];
-				print_byte(ledid & 1 ? b >> 4 : b & 0xf);
-			} else {
-				reg_read_m(RTL837X_REG_LED3_0_SET3);
-				b = sfr_data[3-(((set-2) << 1) + (ledid >> 1))];
-				print_byte(ledid & 1 ? b >> 4 : b & 0xf);
-			}
-			reg_read_m(RTL837X_REG_LED1_0_SET0 - set * 8 - ((ledid >> 1) * 4));
-			if (! (ledid & 1)) { // LEDID 0, 2
-				print_byte(sfr_data[2]); print_byte(sfr_data[3]);
-			} else {
-				print_byte(sfr_data[0]); print_byte(sfr_data[1]);
-			}
-		}
-		write_char('\n');
-	}
-	for (uint8_t i = machine.min_port; i <= machine.max_port; i++) {
-		reg_read_m(RTL837X_LED_PORT_SET_SEL);
-		__xdata uint8_t set = sfr_data[3 - (i >> 2)];
-		set = (set >> ((i & 3) << 1));
-		print_string("Port "); write_char('0' + i); print_string(": SET ");
-		write_char('0' + set);
-		print_string(": ");
-		for (__xdata uint8_t ledid = 0; ledid < 4; ledid++) {
-			write_char('(');
-			reg_read_m(RTL837X_REG_LED1_0_SET0 - set * 8 - ((ledid >> 1) * 4));
-			if (ledid & 1) {  // LEDID 1, 3
-				sfr_data[2] = sfr_data[0];
-				sfr_data[3] = sfr_data[1];
-			}
-			if (sfr_data[3] & 0x01)
-				print_string(" 2G5");
-			if (sfr_data[3] & 0x02)
-				print_string(" TWO_1G");
-			if (sfr_data[3] & 0x04)
-				print_string(" 1G");
-			if (sfr_data[3] & 0x08)
-				print_string(" 500M");
-			if (sfr_data[3] & 0x10)
-				print_string(" 100M");
-			if (sfr_data[3] & 0x20)
-				print_string(" 10M");
-			if (sfr_data[3] & 0x40)
-				print_string(" LINK");
-			if (sfr_data[3] & 0x80)
-				print_string(" LINK_FLASH");
-			if (sfr_data[2] & 0x01)
-				print_string(" ACT");
-			if (sfr_data[2] & 0x02)
-				print_string(" RX");
-			if (sfr_data[2] & 0x04)
-				print_string(" TX");
-			if (sfr_data[2] & 0x08)
-				print_string(" COL");
-			if (sfr_data[2] & 0x10)
-				print_string(" DUPLEX");
-			if (sfr_data[2] & 0x20)
-				print_string(" TRAINING");
-			if (sfr_data[2] & 0x40)
-				print_string(" MASTER");
-			__xdata uint8_t b;
-			if (set < 2) {
-				reg_read_m(RTL837X_REG_LED3_0_SET1);
-				b = sfr_data[3-((set << 1) + (ledid >> 1))];
-			} else {
-				reg_read_m(RTL837X_REG_LED3_0_SET3);
-				b = sfr_data[3-(((set-2) << 1) + (ledid >> 1))];
-			}
-			b = ledid & 1 ? b >> 4 : b & 0xf;
-			if (b & 0x1)
-				print_string(" 10G");
-			if (b & 0x2)
-				print_string(" TWO_5G");
-			if (b & 0x4)
-				print_string(" 5G");
-			if (b & 0x8)
-				print_string(" TWO_2G5");
-			print_string("), ");
-		}
-		write_char('\n');
-	}
-}
-
 
 void leds_setup(void) __banked
 {

rtl837x_leds_dump.c

@@ -0,0 +1,155 @@
+#include <stdint.h>
+#include "rtl837x_common.h"
+#include "rtl837x_sfr.h"
+#include "rtl837x_regs.h"
+#include "rtl837x_leds.h"
+#include "machine.h"
+
+#pragma codeseg BANK3
+#pragma constseg BANK3
+
+extern __code const struct machine machine;
+extern __xdata uint8_t sfr_data[4];
+
+void leds_dump(void) __banked
+{
+	print_string("RTL837X_PIN_MUX_0: "); print_reg(RTL837X_PIN_MUX_0); write_char('\n');
+	print_string("RTL837X_REG_LED_GLB_IO_EN: "); print_reg(RTL837X_REG_LED_GLB_IO_EN); write_char('\n');
+	print_string("RTL837X_REG_LED1_0_SET0: "); print_reg(RTL837X_REG_LED1_0_SET0); write_char('\n');
+	print_string("RTL837X_REG_LED3_2_SET0: "); print_reg(RTL837X_REG_LED3_2_SET0); write_char('\n');
+	print_string("RTL837X_REG_LED1_0_SET1: "); print_reg(RTL837X_REG_LED1_0_SET1); write_char('\n');
+	print_string("RTL837X_REG_LED3_2_SET1: "); print_reg(RTL837X_REG_LED3_2_SET1); write_char('\n');
+	print_string("RTL837X_REG_LED1_0_SET2: "); print_reg(RTL837X_REG_LED1_0_SET2); write_char('\n');
+	print_string("RTL837X_REG_LED3_2_SET2: "); print_reg(RTL837X_REG_LED3_2_SET2); write_char('\n');
+	print_string("RTL837X_REG_LED1_0_SET3: "); print_reg(RTL837X_REG_LED1_0_SET3); write_char('\n');
+	print_string("RTL837X_REG_LED3_2_SET3: "); print_reg(RTL837X_REG_LED3_2_SET3); write_char('\n');
+	print_string("RTL837X_REG_LED3_0_SET1: "); print_reg(RTL837X_REG_LED3_0_SET1); write_char('\n');
+	print_string("RTL837X_REG_LED3_0_SET3: "); print_reg(RTL837X_REG_LED3_0_SET3); write_char('\n');
+	print_string("RTL837X_LED_PORT_SET_SEL: "); print_reg(RTL837X_LED_PORT_SET_SEL); write_char('\n');
+	print_string("RTL837X_REG_LED_GLB_MUX_1: "); print_reg(RTL837X_REG_LED_GLB_MUX_1); write_char('\n');
+	print_string("RTL837X_REG_LED_GLB_MUX_2: "); print_reg(RTL837X_REG_LED_GLB_MUX_2); write_char('\n');
+	print_string("RTL837X_REG_LED_GLB_MUX_3: "); print_reg(RTL837X_REG_LED_GLB_MUX_3); write_char('\n');
+	print_string("RTL837X_REG_LED_GLB_MUX_4: "); print_reg(RTL837X_REG_LED_GLB_MUX_4); write_char('\n');
+	print_string("RTL837X_REG_LED_GLB_MUX_5: "); print_reg(RTL837X_REG_LED_GLB_MUX_5); write_char('\n');
+	print_string("RTL837X_REG_LED_GLB_MUX_6: "); print_reg(RTL837X_REG_LED_GLB_MUX_6); write_char('\n');
+	print_string("RTL837X_REG_LED_GLB_ACTIVE: "); print_reg(RTL837X_REG_LED_GLB_ACTIVE); write_char('\n');
+	print_string("RTL837X_REG_LED_MODE: "); print_reg(RTL837X_REG_LED_MODE); write_char('\n');
+	print_string("LED pad Configuration:\n");
+	for (uint8_t i = 0; i < 28; i++) {
+		print_byte(i);
+		write_char(' ');
+	}
+	write_char('\n');
+	for (uint8_t i = 0; i < 28; i++) {
+		switch (i % 5) {
+		case 0:  // 0
+			reg_read_m(RTL837X_REG_LED_GLB_MUX_1 + (i / 5) * 4);
+			print_byte(sfr_data[3] & 0x3f);
+			break;
+		case 1:  // 6
+			print_byte(((sfr_data[3] >> 6) | (sfr_data[2] << 2)) & 0x3f);
+			break;
+		case 2:  // 12
+			print_byte(((sfr_data[1] << 4) | (sfr_data[2] >> 4)) & 0x3f);
+			break;
+		case 3:  // 18
+			print_byte((sfr_data[1] >> 2) & 0x3f);
+			break;
+		case 4:  // 24
+			print_byte(sfr_data[0] & 0x3f);
+			break;
+		}
+		write_char(' ');
+	}
+	write_char('\n');
+	print_string("LED-set Configuration:\n");
+	print_string("LED-ID\t\t0\t\t1\t\t2\t\t3\n");
+	for (__xdata uint8_t set = 0; set < 4; set++) {
+		print_string("SET "); write_char('0' + set); write_char(':');
+		for (__xdata uint8_t ledid = 0; ledid < 4; ledid++) {
+			print_string("\t   ");
+			uint8_t b;
+			if (set < 2) {
+				reg_read_m(RTL837X_REG_LED3_0_SET1);
+				b = sfr_data[3-((set << 1) + (ledid >> 1))];
+				print_byte(ledid & 1 ? b >> 4 : b & 0xf);
+			} else {
+				reg_read_m(RTL837X_REG_LED3_0_SET3);
+				b = sfr_data[3-(((set-2) << 1) + (ledid >> 1))];
+				print_byte(ledid & 1 ? b >> 4 : b & 0xf);
+			}
+			reg_read_m(RTL837X_REG_LED1_0_SET0 - set * 8 - ((ledid >> 1) * 4));
+			if (! (ledid & 1)) { // LEDID 0, 2
+				print_byte(sfr_data[2]); print_byte(sfr_data[3]);
+			} else {
+				print_byte(sfr_data[0]); print_byte(sfr_data[1]);
+			}
+		}
+		write_char('\n');
+	}
+	for (uint8_t i = machine.min_port; i <= machine.max_port; i++) {
+		reg_read_m(RTL837X_LED_PORT_SET_SEL);
+		__xdata uint8_t set = sfr_data[3 - (i >> 2)];
+		set = (set >> ((i & 3) << 1));
+		print_string("Port "); write_char('0' + i); print_string(": SET ");
+		write_char('0' + set);
+		print_string(": ");
+		for (__xdata uint8_t ledid = 0; ledid < 4; ledid++) {
+			write_char('(');
+			reg_read_m(RTL837X_REG_LED1_0_SET0 - set * 8 - ((ledid >> 1) * 4));
+			if (ledid & 1) {  // LEDID 1, 3
+				sfr_data[2] = sfr_data[0];
+				sfr_data[3] = sfr_data[1];
+			}
+			if (sfr_data[3] & 0x01)
+				print_string(" 2G5");
+			if (sfr_data[3] & 0x02)
+				print_string(" TWO_1G");
+			if (sfr_data[3] & 0x04)
+				print_string(" 1G");
+			if (sfr_data[3] & 0x08)
+				print_string(" 500M");
+			if (sfr_data[3] & 0x10)
+				print_string(" 100M");
+			if (sfr_data[3] & 0x20)
+				print_string(" 10M");
+			if (sfr_data[3] & 0x40)
+				print_string(" LINK");
+			if (sfr_data[3] & 0x80)
+				print_string(" LINK_FLASH");
+			if (sfr_data[2] & 0x01)
+				print_string(" ACT");
+			if (sfr_data[2] & 0x02)
+				print_string(" RX");
+			if (sfr_data[2] & 0x04)
+				print_string(" TX");
+			if (sfr_data[2] & 0x08)
+				print_string(" COL");
+			if (sfr_data[2] & 0x10)
+				print_string(" DUPLEX");
+			if (sfr_data[2] & 0x20)
+				print_string(" TRAINING");
+			if (sfr_data[2] & 0x40)
+				print_string(" MASTER");
+			__xdata uint8_t b;
+			if (set < 2) {
+				reg_read_m(RTL837X_REG_LED3_0_SET1);
+				b = sfr_data[3-((set << 1) + (ledid >> 1))];
+			} else {
+				reg_read_m(RTL837X_REG_LED3_0_SET3);
+				b = sfr_data[3-(((set-2) << 1) + (ledid >> 1))];
+			}
+			b = ledid & 1 ? b >> 4 : b & 0xf;
+			if (b & 0x1)
+				print_string(" 10G");
+			if (b & 0x2)
+				print_string(" TWO_5G");
+			if (b & 0x4)
+				print_string(" 5G");
+			if (b & 0x8)
+				print_string(" TWO_2G5");
+			print_string("), ");
+		}
+		write_char('\n');
+	}
+}

rtl837x_lldp.c

@@ -0,0 +1,161 @@
+#pragma codeseg BANK3
+#pragma constseg BANK3
+
+#include "rtl837x_common.h"
+#include "rtl837x_lldp.h"
+#include "rtl837x_sfr.h"
+#include "rtl837x_common.h"
+#include "dhcp.h"
+#include "uip.h"
+#include "uip/uip.h"
+#include "machine.h"
+
+extern __xdata bool lldp_enabled;
+extern __code const struct machine machine;
+
+__xdata uint16_t lldp_ticks;
+__xdata uint16_t lldp_logical_port_status = 0xffff;
+
+void lldp_init(void) __banked
+{
+    lldp_ticks = 0;
+}
+
+void lldp_tick(void) __banked
+{
+    lldp_ticks++;
+
+    if (lldp_ticks < LLDP_TX_INTERVAL_TICKS)
+        return;
+
+    lldp_ticks = 0;
+
+    if(lldp_enabled == 1)
+        lldp_send();
+}
+
+//Outgoing LLDP packet.
+
+struct lldp_pkt {
+    struct uip_eth_addr dst;
+    struct uip_eth_addr src;
+    struct rtl_tag rtl_tag;
+    uint16_t ether_type;
+
+    uint8_t payload[64];
+};
+
+#define LLDP_O ((__xdata struct lldp_pkt *)&uip_buf[RTL_FRAME_DESC_SIZE])
+
+// The type is 7 bits and the length is 9 bits
+// we can represent this as the 7 most significant
+// bits of the type bit and leave the least significant
+// bit as 0 always as we're not going to need 2^9 for
+// the length at any point
+#define LLDP_TYPE(value) (value << 1)
+
+void lldp_send(void) __banked __reentrant
+{
+    __xdata uint8_t *p;
+    uint8_t port_position;
+
+    lldp_set_addresses();
+    lldp_set_rtl_wrapper();
+
+    p = LLDP_O->payload;
+
+    //Chassis ID
+    *p++ = LLDP_TYPE(LLDP_CHASSIS_ID_TLV_TYPE);
+    *p++ = LLDP_CHASSIS_ID_TLV_LENGTH;
+    *p++ = LLDP_CHASSIS_ID_TLV_SUBTYPE;
+
+    memcpy(p, uip_ethaddr.addr, MAC_ADDR_LEN);
+    p += MAC_ADDR_LEN;
+
+    //Port ID
+    *p++ = LLDP_TYPE(LLDP_PORT_ID_TLV_TYPE);
+    *p++ = LLDP_PORT_ID_TLV_LENGTH;
+    *p++ = LLDP_PORT_ID_TLV_SUBTYPE;
+    port_position = (p-LLDP_O->payload);
+	*p++ = '0';       // filled in per port below
+
+    //TTL
+    *p++ = LLDP_TYPE(LLDP_TTL_TLV_TYPE);
+    *p++ = LLDP_TTL_TLV_LENGTH;
+    *p++ = 0x00; //padding
+    *p++ = LLDP_TTL_TTL_SECONDS;
+
+    p += lldp_sysname(p);
+    p += lldp_sysdesc(p);
+
+    // End of LLDPDU TLV
+    *p++ = 0x00; //padding
+    *p++ = 0x00; //padding
+
+    while (p < (LLDP_O->payload + LLDP_MIN_ETHERNET_PAYLOAD_LENGTH))
+        *p++ = 0x00;
+
+    /*
+     * uip_len is the Ethernet frame length excluding FCS.
+     *
+     * The frame consists of:
+     *
+     *     dst mac
+     *     src mac
+     *     rtl_tag  sizeof(struct rtl_tag)
+     *     EtherType (2 bytes)
+     *     payload (how far we've moved p pointer)
+     */
+    uip_len = MAC_ADDR_LEN + MAC_ADDR_LEN + sizeof(struct rtl_tag) + LLDP_ETHERTYPE_LENGTH + (p - LLDP_O->payload);
+
+    for (uint8_t port = machine.min_port; port <= machine.max_port; port++) {
+
+        if ((1 << port) & lldp_logical_port_status) {
+            LLDP_O->payload[port_position] = '0' + machine.log_to_phys_port[port];
+            LLDP_O->rtl_tag.pmask = HTONS((uint16_t)1 << port);
+
+            tcpip_output();
+        }
+    }
+}
+
+void lldp_set_addresses(void) __banked {
+    // LLDP destination multicast addr: 01:80:c2:00:00:0e
+    memcpyc(LLDP_O->dst.addr, "\x01\x80\xc2\x00\x00\x0e", MAC_ADDR_LEN);
+    memcpy(LLDP_O->src.addr, uip_ethaddr.addr, MAC_ADDR_LEN);
+}
+
+void lldp_set_rtl_wrapper(void) __banked {
+    /*
+     * This is the RTL CPU tag, not the Ethernet EtherType.
+     *     port 0 -> 0x0001
+     *     port 1 -> 0x0002
+     *     port 2 -> 0x0004
+     */
+    LLDP_O->rtl_tag.tag = HTONS(RTL_FRAME_TAG_ID);
+    LLDP_O->rtl_tag.version = RTL_FRAME_TAG_VERSION;
+    LLDP_O->rtl_tag.reason = 0x00;
+    LLDP_O->rtl_tag.flags = HTONS(RTL_TAG_LEARN_DIS);
+
+    LLDP_O->ether_type = HTONS(LLDP_ETHERTYPE);
+}
+
+uint8_t lldp_sysname(__xdata uint8_t *p) __banked
+{
+    uint8_t hostname_length = strlen_x(hostname);
+
+    *p++ = LLDP_TYPE(LLDP_SYSNAME_TLV_TYPE);
+    *p++ = hostname_length;
+    memcpy(p, hostname, hostname_length);
+    return hostname_length + 2;
+}
+
+uint8_t lldp_sysdesc(__xdata uint8_t *p) __banked
+{
+    uint16_t machine_name_length = strlen(machine.machine_name);
+
+    *p++ = LLDP_TYPE(LLDP_SYSDESC_TLV_TYPE);
+    *p++ = machine_name_length;
+    memcpyc(p, machine.machine_name, machine_name_length);
+    return machine_name_length + 2; 
+}

rtl837x_lldp.h

@@ -0,0 +1,36 @@
+#ifndef _LLDP_H_
+#define _LLDP_H_
+
+#include <stdint.h>
+
+#define LLDP_MIN_ETHERNET_PAYLOAD_LENGTH 46
+#define LLDP_ETHERTYPE       0x88cc
+#define LLDP_ETHERTYPE_LENGTH 2
+#define LLDP_MAX_FRAME       256
+#define MAC_ADDR_LEN    6
+#define LLDP_TX_INTERVAL_TICKS 6000
+
+#define LLDP_PORT_ID_TLV_TYPE 2
+#define LLDP_PORT_ID_TLV_LENGTH 0x02
+#define LLDP_PORT_ID_TLV_SUBTYPE 0x07
+
+#define LLDP_TTL_TLV_TYPE 3
+#define LLDP_TTL_TLV_LENGTH 2
+#define LLDP_TTL_TTL_SECONDS 120
+
+#define LLDP_CHASSIS_ID_TLV_TYPE 1
+#define LLDP_CHASSIS_ID_TLV_LENGTH 7
+#define LLDP_CHASSIS_ID_TLV_SUBTYPE 4
+
+#define LLDP_SYSNAME_TLV_TYPE 5
+#define LLDP_SYSDESC_TLV_TYPE 6
+
+void lldp_init(void) __banked;
+void lldp_tick(void) __banked;
+void lldp_send(void) __banked;
+void lldp_set_addresses(void) __banked;
+void lldp_set_rtl_wrapper(void) __banked;
+uint8_t lldp_sysname(__xdata uint8_t *p) __banked;
+uint8_t lldp_sysdesc(__xdata uint8_t *p) __banked;
+
+#endif

rtl837x_phy.c

@@ -23,6 +23,8 @@
 extern __code const uint16_t bit_mask[16];
 extern __code const struct machine machine;
 extern __xdata struct machine_runtime machine_detected;
+extern volatile __xdata uint32_t ticks;
+extern __xdata uint32_t rtl8224_release_tick;
 
 __xdata struct phy_settings phy_settings;
 
@@ -214,9 +216,20 @@ void phy_config(uint8_t phy) __banked
 }
 
 
+void rtl8224_wait_ready(void) __banked
+{
+	do {
+		rtl8224_read_reg_u16(RTL837X_REG_CHIP_ID + 1);
+		if (SFR_DATA_U16 == 0x8224)
+			return;
+	} while ((ticks - rtl8224_release_tick) < (SYS_TICK_HZ * 5 / 2));
+	print_string("\r\nRTL8224 not responding\r\n");
+}
+
 void phy_config_8224(void) __banked
 {
 	uint16_t pval;
+	uint16_t tries;
 	print_string("\r\nphy_config_8224 called\r\nRTL8224 ID: ");
 
 	// Print RTL8224 chip id
@@ -244,9 +257,12 @@ void phy_config_8224(void) __banked
 		i++;
 		rtl8224_write_reg_u16(RTL837X_SDS_INDACS_CMD, rtl8224_sds0_setttings[i]);
 		i++;
+		tries = 0xffff;
 		do {
 			rtl8224_read_reg_u16(0x3f8);
-		} while (SFR_DATA_8 & 0x80);
+		} while ((SFR_DATA_8 & 0x80) && --tries);
+		if (SFR_DATA_8 & 0x80)
+			print_string("\r\nRTL8224 SerDes access timed out\r\n");
 	}
 
 	print_string("\r\nphy_config_8224 done\r\n");
@@ -354,8 +370,9 @@ void phy_set_speed(void) __banked
 			phy_modify(phy_settings.port, PHY_MMD31, PHY_MMD31_GBCR, 0x0200, 0x0000);
 		} else {
 			// AN Advertisement Register (MMD 7.0x0010)
-			// bits 0-4: 0x1 (802.3 supported), Extended Next Page format used
-			phy_write(phy_settings.port, PHY_MMD_AN, PHY_ANEG_ADV, 0x1001);
+			// bits 0-4: 0x1 (802.3 supported), bit 10: PAUSE,
+			// Extended Next Page format used
+			phy_write(phy_settings.port, PHY_MMD_AN, PHY_ANEG_ADV, 0x1401);
 			if (phy_settings.speed == PHY_SPEED_1G) {
 				// Multi-GBASE-TBASE-T AN Control 1 Register (MMD 7.0x0020)
 				// bit 14: SLAVE, bit 13: Multi-Port device, 1: LD Loop timin enableed

rtl837x_phy.h

@@ -22,6 +22,7 @@ extern __xdata struct phy_settings phy_settings;
 void rtl8224_phy_enable(void) __banked;
 void phy_config(uint8_t phy) __banked;
 void phy_config_8224(void) __banked;
+void rtl8224_wait_ready(void) __banked;
 void phy_set_speed(void) __banked;
 void phy_set_duplex(void) __banked;
 void phy_show(uint8_t port) __banked;

rtl837x_port.c

@@ -40,7 +40,6 @@ static void wait_table_ready(void)
 
 void port_mirror_set(uint8_t port, __xdata uint16_t rx_pmask, __xdata uint16_t tx_pmask) __banked
 {
-	print_string("\nport_mirror_set called \n");
 	print_string("Mirroring port: "); print_byte(port); print_string(" with rx-mask: ");
 	print_short(rx_pmask); print_string(", tx mask: "); print_short(tx_pmask);
 	write_char('\n');
@@ -52,7 +51,6 @@ void port_mirror_set(uint8_t port, __xdata uint16_t rx_pmask, __xdata uint16_t t
 
 void port_mirror_del(void) __banked
 {
-	print_string("\nport_mirror_del called \n");
 	REG_SET(RTL837x_MIRROR_CTRL, 0);
 }
 
@@ -112,7 +110,6 @@ void port_pvid_set(uint8_t port, __xdata uint16_t pvid) __banked
 {
 	uint8_t lag = port_lag_of(port);
 
-	print_string("\nport_pvid_set called \n");
 	if (lag == PORT_LAG_NONE) {
 		port_pvid_write(port, pvid);
 		return;
@@ -141,7 +138,6 @@ void vlan_delete(uint16_t vlan) __banked
 	if (!vlan || vlan >= 0xfff)
 		return;
 
-	print_string("\nvlan_delete called \n"); print_short(vlan);
 	vlan_name_remove(vlan);
 	REG_WRITE(RTL837x_TBL_DATA_IN_A, 0, 0, 0, 0);
 	REG_WRITE(RTL837X_TBL_CTRL, vlan >> 8, vlan, TBL_VLAN, TBL_WRITE | TBL_EXECUTE);
@@ -232,7 +228,7 @@ void vlan_create(void) __banked
 	vlan_settings.members |= 0x0200; // Set 10th bit
 	vlan_settings.tagged |= 0x0200;
 
-	print_string("\nvlan_create called\nvlan: "); print_short(vlan_settings.vlan);
+	print_string("vlan: "); print_short(vlan_settings.vlan);
 	print_string(", members: "); print_short(vlan_settings.members);
 	print_string(", tagged: "); print_short(vlan_settings.tagged); write_char('\n');
 
@@ -250,7 +246,6 @@ void vlan_create(void) __banked
 
 	wait_table_ready();
 
-	print_string("vlan_create done \n");
 }
 
 
@@ -263,7 +258,6 @@ void vlan_create(void) __banked
  */
 void vlan_setup(void) __banked
 {
-	print_string("\nvlan_setup called \n");
 
 	// No VLAN names set up so far
 	vlan_ptr = 0;
@@ -331,7 +325,6 @@ void vlan_setup(void) __banked
 	print_string("\nvlan_setup, REG 0x4f4c: "); print_reg(0x4f4c);
 #endif
 
-	print_string("vlan_setup done \n");
 }
 
 
@@ -354,7 +347,6 @@ void port_l2_forget_port(uint8_t port) __banked
  */
 uint8_t port_l2_forget(void) __banked
 {
-	print_string("\nport_l2_forget called\n");
 	// Configure the entries to be flushed:
 	// port-based (bits 0-1 are 0 and dynamic entries, bit 2 specifies dynamic entries
 	REG_SET(RTL837x_L2_TBL_FLUSH_CNF, 0x0);
@@ -370,7 +362,6 @@ uint8_t port_l2_forget(void) __banked
 		reg_read_m(RTL837x_L2_TBL_FLUSH_CTRL);
 	} while (sfr_data[1]);
 
-	print_string("port_l2_forget done\n");
 	return 0;
 }
 
@@ -465,7 +456,6 @@ void port_l2mc_set(uint8_t mac_last, __xdata uint16_t vid, __xdata uint16_t pmas
  */
 void port_l2_setup(void) __banked
 {
-	print_string("\nport_l2_setup called\n");
 
 	port_l2_forget();
 
@@ -483,7 +473,38 @@ void port_l2_setup(void) __banked
 	// When maximim entries learned, then simply flood the packet
 	reg_bit_set(RTL837X_L2_LRN_PORT_CONSTRT_ACT, 0);
 
-	print_string("\nport_l2_setup done\n");
+}
+
+
+void port_media_show(uint8_t port) __banked
+{
+	uint8_t pause;
+
+	if (!machine.is_sfp[port]) {
+		reg_read_m(RTL837X_REG_LINKS_STS);
+		if (sfr_data[(port / 8) + 1] >> (port % 8) & 1) {
+			print_string("Link role: ");
+			reg_read_m(RTL837X_MAC_MSTR_SLV_STS);
+			if (sfr_data[3 - (port >> 3)] & (1 << (port & 7)))
+				print_string("master\n");
+			else
+				print_string("slave\n");
+		}
+	}
+
+	print_string("Pause negotiated:");
+	reg_read_m(RTL837X_MAC_TX_PAUSE_STS);
+	pause = sfr_data[3 - (port >> 3)] & (1 << (port & 7));
+	if (pause)
+		print_string(" TX");
+	reg_read_m(RTL837X_MAC_RX_PAUSE_STS);
+	if (sfr_data[3 - (port >> 3)] & (1 << (port & 7))) {
+		print_string(" RX");
+		pause = 1;
+	}
+	if (!pause)
+		print_string(" none");
+	write_char('\n');
 }
 
 

rtl837x_port.h

@@ -49,6 +49,7 @@ extern __xdata struct vlan_settings vlan_settings;
 uint8_t port_l2_forget(void) __banked;
 void port_l2_learned(void) __banked;
 void port_stats_print(void) __banked;
+void port_media_show(uint8_t port) __banked;
 int8_t vlan_get(uint16_t vlan) __banked;
 __xdata uint16_t vlan_name(uint16_t vlan) __banked;
 void vlan_name_remove(uint16_t vlan) __banked;

rtl837x_regs.h

@@ -9,6 +9,13 @@
 #define RESET_SOC_BIT			0
 #define RESET_NIC_BIT			2
 
+#define RTL837X_TM_CTRL2		0x0338
+#define TM_CTRL2_EN_LATCH		0x04
+#define RTL837X_TM_RESULT		0x0340
+#define RTL837X_TM_RESULT_POWERON	0x0350
+// Temperature: 19 bit value, bits 18:3 in the low 16 bits of the register,
+// bits 2:0 in bits 18:16. Bit 18 signed, bits 17:10 degrees C, bits 9:0 fraction.
+
 #define RTL837X_REG_HW_CONF		0x6040
 // Bits 4 & 5: CLOCK DIVIDER from 125MHz for Timer
 
@@ -83,6 +90,10 @@
 #define RTL837X_REG_LINKS	0x63f0
 #define RTL837X_REG_LINKS_89	0x63f4
 #define RTL837X_REG_LINKS_STS	0x63E8
+/* Per-port status bits: bit N is chip port N */
+#define RTL837X_MAC_TX_PAUSE_STS	0x63FC
+#define RTL837X_MAC_RX_PAUSE_STS	0x6400
+#define RTL837X_MAC_MSTR_SLV_STS	0x6408
 
 /* Each nibble encodes the link state of a port.
    Port 0 appears to be the CPU port
@@ -141,6 +152,10 @@
 #define RTL837X_REG_RX_CTRL		0x785c
 #define RTL837X_REG_TX_CTRL		0x7860
 #define RTL837X_REG_NIC_RX_BUFF_DATA	0x7874
+#define RTL837X_NIC_INT_STS		0x7854
+#define RTL837X_NIC_INT_MSK		0x7858
+#define NIC_INT_RXIS			0x02
+#define NIC_INT_RXIE			0x02
 #define RTL837X_REG_CPU_RX_CURR_PKT	0x787c
 #define RTL837X_REG_NIC_TX_CURR_PKT	0x7884
 #define RTL837X_REG_CPU_TX_CURR_PKT	0x7890
@@ -270,6 +285,9 @@
  */
 #define RTL8373_RLDP_TIMER		0x1074
 #define RTL837X_RMA0_CONF		0x4ecc
+#define RTL837X_IMR_INT_PORT_LINK_STS_CHG	0x5f34
+#define RTL837X_ISR_SW_INT_MODE		0x5f84
+#define RTL837X_ISR_INT_PORT_LINK_CHG	0x5f88
 #define RTL837X_RMA_CONF		0x4f1c
 #define RTL837X_MSTP_STATES		0x5310
 #define RTL837X_REG_LED_RLDP_1		0x65F8
@@ -309,6 +327,11 @@
 #define RTL837X_IGBW_PORT_FC_CTRL	0x4C8C
 #define RTL837X_EGBW_PORT_CTRL		0x1c34
 #define RTL837X_EGBW_CTRL		0x447c
+#define RTL837X_STORM_CTRL		0x54e4
+#define RTL837X_STORM_MIDX		0x54f4
+#define RTL837X_METER_RATE		0x5cf0
+#define RTL837X_METER_BURST		0x5df0
+#define RTL837X_METER_MODE		0x5ef0
 #define EGBW_INC_IFG			0x02
 #define EGBW_CPUMODE			0x01
 

rtl837x_storm.c

@@ -0,0 +1,89 @@
+#include <stdint.h>
+#include "rtl837x_common.h"
+#include "rtl837x_sfr.h"
+#include "rtl837x_regs.h"
+#include "rtl837x_storm.h"
+#include "machine.h"
+
+#pragma codeseg BANK3
+#pragma constseg BANK3
+
+extern __code const struct machine machine;
+extern __xdata uint8_t sfr_data[4];
+
+/* RTL837X_STORM_MIDX words, row type * 2 + half: half 0 holds ports 0-4, half 1 ports 5-9,
+ * 6 bits per port, each set to STORM_METER(port, type) */
+static const __code uint8_t storm_midx[8][4] = {
+	{ 0x28, 0x92, 0x07, 0x18 }, { 0x3c, 0xe3, 0x4c, 0x2c },
+	{ 0x29, 0x96, 0x17, 0x59 }, { 0x3d, 0xe7, 0x5c, 0x6d },
+	{ 0x2a, 0x9a, 0x27, 0x9a }, { 0x3e, 0xeb, 0x6c, 0xae },
+	{ 0x2b, 0x9e, 0x37, 0xdb }, { 0x3f, 0xef, 0x7c, 0xef },
+};
+
+static __code const char * __code const storm_names[STORM_TYPES] = { " bcast ", " mcast ", " ucast ", " umcast " };
+
+
+void storm_set(uint8_t port, __xdata uint8_t type, __xdata uint32_t rate, __xdata uint8_t pps) __banked
+{
+	__xdata uint8_t idx = STORM_METER(port, type);
+	__xdata uint8_t row = (type << 1) | (port >= 5 ? 1 : 0);
+	__xdata uint8_t * __xdata r = (uint8_t *)&rate;
+
+	sfr_data[0] = 0;
+	sfr_data[1] = r[2];
+	sfr_data[2] = r[1];
+	sfr_data[3] = r[0];
+	reg_write_m(RTL837X_METER_RATE + (idx << 2));
+
+	if (!pps) {
+		sfr_data[1] = 0;
+		sfr_data[2] = 0x20;
+		sfr_data[3] = 0;
+	}
+	reg_write_m(RTL837X_METER_BURST + (idx << 2));
+
+	if (pps)
+		reg_bit_set(RTL837X_METER_MODE + ((idx >> 5) << 2), idx & 0x1f);
+	else
+		reg_bit_clear(RTL837X_METER_MODE + ((idx >> 5) << 2), idx & 0x1f);
+
+	sfr_data[0] = storm_midx[row][0];
+	sfr_data[1] = storm_midx[row][1];
+	sfr_data[2] = storm_midx[row][2];
+	sfr_data[3] = storm_midx[row][3];
+	reg_write_m(RTL837X_STORM_MIDX + (row << 2));
+
+	reg_bit_set(RTL837X_STORM_CTRL + (type << 2), port);
+}
+
+
+void storm_off(uint8_t port, __xdata uint8_t type) __banked
+{
+	reg_bit_clear(RTL837X_STORM_CTRL + (type << 2), port);
+}
+
+
+void storm_show(void) __banked
+{
+	uint8_t i, t, idx;
+
+	for (i = machine.min_port; i <= machine.max_port; i++) {
+		print_string("port ");
+		write_char('0' + machine.log_to_phys_port[i]);
+		for (t = 0; t < STORM_TYPES; t++) {
+			print_string(storm_names[t]);
+			if (!reg_bit_test(RTL837X_STORM_CTRL + (t << 2), i)) {
+				print_string("off");
+				continue;
+			}
+			idx = STORM_METER(i, t);
+			reg_read_m(RTL837X_METER_RATE + (idx << 2));
+			print_byte(sfr_data[1]); print_byte(sfr_data[2]); print_byte(sfr_data[3]);
+			if (reg_bit_test(RTL837X_METER_MODE + ((idx >> 5) << 2), idx & 0x1f))
+				print_string(" pps");
+			else
+				print_string(" kbps");
+		}
+		write_char('\n');
+	}
+}

rtl837x_storm.h

@@ -0,0 +1,14 @@
+#ifndef _RTL837X_STORM_H_
+#define _RTL837X_STORM_H_
+
+#include <stdint.h>
+
+#define STORM_TYPES	4
+#define STORM_METER_BASE	24
+#define STORM_METER(port, type)	(STORM_METER_BASE + (((port) << 2) | (type)))
+
+void storm_set(uint8_t port, __xdata uint8_t type, __xdata uint32_t rate, __xdata uint8_t pps) __banked;
+void storm_off(uint8_t port, __xdata uint8_t type) __banked;
+void storm_show(void) __banked;
+
+#endif

rtlplayground.c

@@ -16,6 +16,7 @@
 #include "rtl837x_leds.h"
 #include "rtl837x_bandwidth.h"
 #include "rtl837x_init.h"
+#include "rtl837x_lldp.h"
 #include "dhcp.h"
 #include "cmd_parser.h"
 #include "cmd_editor.h"
@@ -88,11 +89,14 @@ __xdata struct uip_eth_addr uip_ethaddr;
 volatile __xdata uint32_t ticks;
 volatile __xdata uint8_t sec_counter;
 volatile __xdata uint16_t sleep_ticks;
-__xdata uint8_t stp_clock;
+__xdata uint8_t stp_tick_last;
 __xdata uint8_t arp_age_secs;
 extern __xdata struct dhcp_state dhcp_state;
 
-#define STP_TICK_DIVIDER 3
+#define STP_TICK_STEP (SYS_TICK_HZ / STP_HZ)
+#define STP_CATCH_UP 8
+#define SFP_TICK_STEP 10
+__xdata uint8_t sfp_tick_last;
 
 /* Buffer for serial input, SBUF_SIZE must be power of 2 < 256
  * Writing to this buffer is under the sole control of the serial ISR
@@ -124,6 +128,7 @@ __xdata uint8_t tx_seq;
 
 __xdata bool stp_enabled;
 __xdata uint8_t igmpEnabled;
+__xdata bool lldp_enabled;
 __xdata char hostname[24];	/* device hostname, default set at boot, see rtl837x_common.h */
 
 __code const uint16_t bit_mask[16] = {
@@ -134,6 +139,11 @@ __code const uint16_t bit_mask[16] = {
 
 __xdata uint8_t linkbits_last[4];
 __xdata uint8_t linkbits_last_p89;
+__data __at(0x20) volatile uint8_t evflags;
+volatile __bit __at(0x00) link_irq;
+volatile __bit __at(0x01) rx_irq;
+volatile __bit __at(0x02) tick_pending;
+__bit __at(0x03) cmd_available;
 // Last known state of the SFP detection/Loss of Signal pins
 __xdata bool button_last;
 __xdata uint8_t button_sec_counter_last;
@@ -195,6 +205,7 @@ void isr_timer0(void) __interrupt(1)
 void isr_timer2(void) __interrupt(5)
 {
 	ticks++;
+	tick_pending = 1;
 	if (sleep_ticks > 0)
 		sleep_ticks--;
 	sec_counter++;
@@ -401,6 +412,16 @@ uint16_t strlen_x(__xdata const char *s)
 }
 
 
+uint16_t strcpy(__xdata uint8_t *dst, const char *s)
+{
+	__xdata uint8_t *b = dst;
+	while (*s)
+		*dst++ = *s++;
+	*dst = 0;
+	return dst - b;
+}
+
+
 char strcmp(__xdata const uint8_t *a, __code const uint8_t *b)
 {
 	uint8_t i = 0;
@@ -489,14 +510,14 @@ void print_cmd_prompt(void)
 }
 
 /*
- * External IRQ 0 Service Routine: Called on link change?
- * Note that all registers are being put on the STACK because of calling a subroutine
+ * External IRQ 0 Service Routine: the switch reports a link change. The
+ * register access macros share the SFR data bytes with the main loop, so
+ * the handler only latches the event; idle() reads and clears it.
  */
 void isr_ext0(void) __interrupt(0)
 {
-	EX0 = 0;	// Disable interrupt for the moment
-	IT0 = 1;	// Trigger on falling edge of external interrupt
-	EX0 = 1;	// Re-enable interrupt
+	EX0 = 0;
+	link_irq = 1;
 }
 
 
@@ -505,9 +526,8 @@ void isr_ext0(void) __interrupt(0)
  */
 void isr_ext1(void) __interrupt(2)
 {
-	// This flag should only be reset after all packets have been read
 	EX1 = 0;
-	EX1 = 1;
+	rx_irq = 1;
 }
 
 /*
@@ -1015,6 +1035,7 @@ void handle_rx(void)
 			REG_SET(RTL837X_REG_NIC_RXCMD, 1);
 			return;
 		}
+		health_rx_frame();
 
 #ifdef RXTXDBG
 		print_string("\n<< ");
@@ -1043,8 +1064,7 @@ void handle_rx(void)
 				tcpip_output();
 			}
 		} else if (igmpEnabled && uip_buf[0] == 0x01 && uip_buf[1] == 0x00 && uip_buf[2] == 0x5e // IPv4-MC packet?
-			&& uip_buf[3] == 0x00 && uip_buf[4] == 0x00 && uip_buf[5] == 0x16) {
-			igmp_packet_handler();
+			&& igmp_packet_handler()) {
 			if (uip_len) {
 				tcpip_output();
 			}
@@ -1168,56 +1188,8 @@ void handle_button(void)
 	}
 }
 
-//
-// An idle function that sleeps for 1 tick and does all the house-keeping
-//
-void idle(void)
+void check_links(void)
 {
-	reg_read(RTL837X_REG_NIC_RX_BUFF_DATA);
-	if (!SFR_DATA_U16)
-		PCON |= 1;
-	if (sec_counter >= SYS_TICK_HZ) {
-		sec_counter -= SYS_TICK_HZ;
-		reg_read_m(RTL837X_REG_SEC_COUNTER);
-		uint8_t v = sfr_data[3];
-#ifdef DEBUG
-		print_string("  Tick counter: "); print_long(ticks); write_char('\n');
-#endif
-		v++;
-		sfr_data[3] = v;
-		if (!v) {
-			v = sfr_data[2];
-			v++;
-			sfr_data[2] = v;
-			if (!v) {
-				v = sfr_data[1];
-				v++;
-				sfr_data[1] = v;
-				if (!v) {
-					v = sfr_data[0];
-					v++;
-					sfr_data[0] = v;
-				}
-			}
-		}
-		reg_write_m(RTL837X_REG_SEC_COUNTER);
-		reg_read_m(RTL837X_REG_SEC_COUNTER);
-
-		// Check for button presses once a second
-		handle_button();
-		// Age the ARP cache: uip_arp_timer() expects a 10 s cadence
-		if (++arp_age_secs >= 10) {
-			arp_age_secs = 0;
-			uip_arp_timer();
-		}
-
-#ifdef DEBUG
-		print_sfr_data();
-		write_char('\n');
-#endif
-	}
-
-	// Check for Link changes
 	reg_read_m(RTL837X_REG_LINKS_89);
 	__xdata uint8_t linkbits_p89 = sfr_data[3];
 
@@ -1250,24 +1222,104 @@ void idle(void)
 			cpy_4(linkbits_last, sfr_data);
 		}
 	}
+}
 
-	// Check for changes with SFP modules
-	handle_sfp();
 
-	// Check new Packets RX
-	handle_rx();
-	// Check UIP for packets to transmit
+//
+// An idle function that sleeps for 1 tick and does all the house-keeping
+//
+static void handle_tick(void)
+{
+	if (sec_counter >= SYS_TICK_HZ) {
+		sec_counter -= SYS_TICK_HZ;
+		reg_read_m(RTL837X_REG_SEC_COUNTER);
+		uint8_t v = sfr_data[3];
+#ifdef DEBUG
+		print_string("  Tick counter: "); print_long(ticks); write_char('\n');
+#endif
+		v++;
+		sfr_data[3] = v;
+		if (!v) {
+			v = sfr_data[2];
+			v++;
+			sfr_data[2] = v;
+			if (!v) {
+				v = sfr_data[1];
+				v++;
+				sfr_data[1] = v;
+				if (!v) {
+					v = sfr_data[0];
+					v++;
+					sfr_data[0] = v;
+				}
+			}
+		}
+		reg_write_m(RTL837X_REG_SEC_COUNTER);
+		reg_read_m(RTL837X_REG_SEC_COUNTER);
+
+		// Check for button presses once a second
+		handle_button();
+		link_irq = 1;
+		// Age the ARP cache: uip_arp_timer() expects a 10 s cadence
+		if (++arp_age_secs >= 10) {
+			arp_age_secs = 0;
+			uip_arp_timer();
+		}
+
+#ifdef DEBUG
+		print_sfr_data();
+		write_char('\n');
+#endif
+	}
+
+	health_phase(HEALTH_PH_LINK);
+	if (TICKS_DUE(sfp_tick_last, SFP_TICK_STEP)) {
+		sfp_tick_last += SFP_TICK_STEP;
+		handle_sfp();
+	}
+	health_phase(HEALTH_PH_SFP);
 	handle_tx();
-	// If STP protocol enabled, decrease STP timers to trigger actions
+	health_phase(HEALTH_PH_TX);
 	if (stp_enabled) {
-		if (!stp_clock) {
-			stp_clock = STP_TICK_DIVIDER;
+		uint8_t n = STP_CATCH_UP;
+		while (n-- && TICKS_DUE(stp_tick_last, STP_TICK_STEP)) {
+			stp_tick_last += STP_TICK_STEP;
 			stp_timers();
-		} else {
-			stp_clock--;
 		}
 	}
-	// Check whether a command is waiting in the cmd_buffer and execute
+	health_phase(HEALTH_PH_STP);
+	lldp_tick();
+	health_phase(HEALTH_LLDP);
+}
+
+
+void idle(void)
+{
+	if (!evflags)
+		PCON |= 1;
+	health_loop_start();
+	if (tick_pending) {
+		tick_pending = 0;
+		handle_tick();
+	}
+	if (link_irq) {
+		link_irq = 0;
+		REG_SET(RTL837X_ISR_INT_PORT_LINK_CHG, 0x3ff);
+		EX0 = 1;
+		check_links();
+	}
+	health_phase(HEALTH_PH_LINK);
+	if (rx_irq) {
+		rx_irq = 0;
+		handle_rx();
+		REG_SET(RTL837X_NIC_INT_STS, NIC_INT_RXIS);
+		reg_read(RTL837X_REG_NIC_RX_BUFF_DATA);
+		if (SFR_DATA_U16)
+			rx_irq = 1;
+		else
+			EX1 = 1;
+	}
+	health_phase(HEALTH_PH_RX);
 	if (cmd_available) {
 		cmd_available = 0;
 		cmd_tokenize();
@@ -1275,6 +1327,7 @@ void idle(void)
 			cmd_parser();
 		print_cmd_prompt();
 	}
+	health_phase(HEALTH_PH_CMD);
 }
 
 
@@ -1300,14 +1353,16 @@ void reset_chip(void)
 
 void setup_external_irqs(void)
 {
-	REG_SET(0x5f84, 0x42);
-	REG_SET(0x5f34, 0x3ff);
+	REG_SET(RTL837X_ISR_SW_INT_MODE, 0x42);
+	REG_SET(RTL837X_ISR_INT_PORT_LINK_CHG, 0x3ff);
+	REG_SET(RTL837X_IMR_INT_PORT_LINK_STS_CHG, 0x3ff);
 
-//	EX0 = 1;	// Enable external IRQ 0 (Link-change)
-	EX0 = 0;
-	IT0 = 1;	// External IRQ on falling edge
+	link_irq = 1;
+	IT0 = 1;	// External IRQ 0 on falling edge (link change)
+	EX0 = 1;
 
-	EX1 = 1;	// External IRQ 1 enable
+	rx_irq = 1;
+	EX1 = 1;	// External IRQ 1: the NIC has received a packet
 	EX2 = 1;	// External IRQ 2 enable: bit EIE.0
 	EX3 = 1;	// External IRQ 3 enable: bit EIE.1
 	PX3 = 1;	// Set EIP.1 = 1: External IRQ 3 set to high priority
@@ -1588,7 +1643,8 @@ void check_and_flash_update_image(void)
 void main(void)
 {
 	ticks = 0;
-	stp_clock = STP_TICK_DIVIDER;
+	stp_tick_last = (uint8_t)ticks;
+	sfp_tick_last = (uint8_t)ticks;
 	dhcp_state.state = DHCP_OFF;
 	sbuf_ptr = 0;
 
@@ -1692,14 +1748,14 @@ void main(void)
 
 	REG_SET(RTL837X_PIN_MUX_2, 0x0); // Disable pins for ACL
 	init_smi();
+	if (machine_detected.isRTL8373)
+		rtl8224_wait_ready();
 
 	rtl8373_revision();
 
 	leds_setup();
 	machine_custom_init();
 
-	leds_dump();
-
 	set_sys_led_state(SYS_LED_SLOW);
 
 	if (machine_detected.isRTL8373)
@@ -1732,6 +1788,7 @@ void main(void)
 	stp_enabled = 0;
 	stp_defaults();		/* 802.1D/w default config before any "stp ..." replay */
 	nic_setup();
+	REG_SET(RTL837X_NIC_INT_MSK, NIC_INT_RXIE);
 	vlan_setup();
 	port_l2_setup();
 	igmp_setup();
@@ -1739,6 +1796,7 @@ void main(void)
 	uip_init();
 	uip_arp_init();
 	httpd_init();
+	lldp_init();
 
 	management_vlan = 1; // Default management VLAN is 1
 
@@ -1769,6 +1827,7 @@ void main(void)
 
 	cmd_editor_init();
 
+	health_stack_paint();
 	while (1) {
 		cmd_edit();
 		idle(); // Enter Idle mode until interrupt occurs

rwintercept_zoerax_hg0402xg.asm

@@ -0,0 +1,410 @@
+; Assembler file to intercept register writes/reads and PHY writes/reads
+; assemble with as31
+; Compile with
+; as31 -Fbyte -Orwintercept_zoerax_hg0402xg.hex rwintercept_zoerax_hg0402xg.asm
+; ./injector zoerax_hg0402xg.bin RTLPlayground/rwintercept_zoerax_hg0402xg.hex zoerax_hg0402xg_patched.bin
+; Start at 0x3b00, where there is always some space in BANK 0
+	.equ	valptr, 0xc7
+
+
+	.equ	SFR_DATA_0, 0xa7
+	.equ	SFR_DATA_8, 0xa6
+	.equ	SFR_DATA_16, 0xa5
+	.equ	SFR_DATA_24, 0xa4
+
+; Intercept Register Write
+	.org 0x4d62
+	lcall	reg_write
+	nop
+
+; Intercept Register Read
+	.org 0x4dad
+	lcall	reg_read_head
+	.org 0x4e6f
+	lcall	reg_read_tail
+
+; Intercept PHY write
+	.org 0x522c
+	lcall	phy_write
+
+; Intercept PHY read
+	.org 0x526f
+	lcall	phy_read_head
+	.org 0x5295
+	ljmp	phy_read_tail
+
+; Intercept SDS write
+	.org 0x503c
+	lcall	sds_write
+	nop
+
+; Intercept SDS read
+	.org 0x5061
+	lcall	sds_read_head
+	nop
+	.org 0x507b
+	ljmp	sds_read_tail
+
+;
+; BEGIN actual code at unused end of BANK0
+;
+	.org 0x3b00
+
+;
+; print the address of a register write. The address is in R6/R7. A and r4 can be scratched
+;
+reg_write:	
+	mov	a, #'R'
+	acall	putc
+
+	mov	a, r6
+	acall	wbyte
+
+	mov	a, r7
+	acall	wbyte
+
+	mov	a, #'-'
+	acall	putc
+
+	mov	dptr, #valptr
+	movx	a, @dptr
+	acall	wbyte
+	mov	dptr, #valptr + 1
+	movx	a, @dptr
+	acall	wbyte
+	mov	dptr, #valptr + 2
+	movx	a, @dptr
+	acall	wbyte
+	mov	dptr, #valptr + 3
+	movx	a, @dptr
+	acall	wbyte
+
+	mov	a, #' '
+	acall	putc
+
+	mov	a, r7
+	mov	r5, a
+	mov	a, r6
+	mov	r4, a
+	ret
+
+;
+; print the address of a register read The address is in R2/R3. Registers 4-7 are scratch
+;
+reg_read_head:
+	mov	a, #'r'
+	acall	putc
+
+	mov	a, r2
+	acall	wbyte
+
+	mov	a, r3
+	acall	wbyte
+
+	mov	a, #':'
+	acall	putc
+	clr	a
+	mov	r7, a
+	mov	r6, a
+	mov	r5, a
+	mov	r4, a
+	ret
+
+reg_read_tail:
+	mov	dptr, #0xc5
+	movx	a, @dptr
+	acall	wbyte
+	mov	dptr, #0xc5 + 1
+	movx	a, @dptr
+	acall	wbyte
+	mov	dptr, #0xc5 + 2
+	movx	a, @dptr
+	acall	wbyte
+	mov	dptr, #0xc5 + 3
+	movx	a, @dptr
+	acall	wbyte
+
+	mov	a, #' '
+	acall	putc
+
+	mov	dptr,#0xc5
+	ret
+
+
+;
+; print phy write options
+;
+phy_write:
+	mov	a, #'P'
+	acall	putc
+
+	mov	a, r4
+	acall	wbyte
+
+; phymask
+	mov	a, r6
+	acall	wbyte
+	mov	a, r7
+	acall	wbyte
+
+	mov	a, #'.'
+	acall	putc
+
+; dev_id?
+	mov	a, r5
+	acall	wbyte
+
+; x_phywrite_opt
+	mov	dptr, #0xf1
+	movx	a, @dptr
+	acall	wbyte
+
+; The register going to SFR_C2 and SFR_C3
+	mov	a, r2
+	acall	wbyte
+	mov	a, r3
+	acall	wbyte
+
+	mov	a, #':'
+	acall	putc
+
+	mov	dptr, #0xf2
+	movx	a, @dptr
+	acall	wbyte
+
+	
+	mov	dptr, #0xf3
+	movx	a, @dptr
+	acall	wbyte
+
+	mov	a, #' '
+	acall	putc
+
+	mov	dptr, #0xeb
+	mov	r4, #0
+	ret
+
+;
+; print phy read options
+;
+phy_read_head:
+	mov	r1, 4	; actually r4
+
+	mov	a, #'p'
+	acall	putc
+
+	mov	a, r7
+	acall	wbyte
+
+	mov	a, r5
+	acall	wbyte
+
+	mov	a, #'.'
+	acall	putc
+
+	mov	a, r2
+	acall	wbyte
+	mov	a, r3
+	acall	wbyte
+
+	mov	a, #':'
+	acall	putc
+
+	mov	r1, 7
+	mov	a, r2
+	ret
+
+phy_read_tail:
+	mov	r6, 4
+	mov	a, r6
+	acall	wbyte
+	mov	a, r7
+	acall	wbyte
+
+	mov	a, #' '
+	acall	putc
+	mov	r4, 6
+	ret
+
+	
+;
+; print SDS write options
+;
+sds_write:
+	mov	a, r4
+	mov	r2, a	; R2 is scratch
+
+	mov	a, #'Q'
+	acall	putc
+
+
+	mov	a, r7
+	acall	wbyte
+	mov	a, r5
+	acall	wbyte
+	mov	a, r3
+	acall	wbyte
+	
+	mov	a, #':'
+	acall	putc
+
+	mov	dptr, #0xe1
+	movx	a, @dptr
+	acall	wbyte
+
+	
+	mov	dptr, #0xe2
+	movx	a, @dptr
+	acall	wbyte
+
+	mov	a, #' '
+	acall	putc
+
+	mov	a, r7
+	mov	r1, a
+	mov	a, r5
+	mov	r7, a
+	mov	a, r2
+	mov	r4, a
+	ret
+
+;
+; print SDS read options
+;
+sds_read_head:
+	mov	a, r4
+	mov	r1, a	; R1 is scratch
+
+	mov	a, #'q'
+	acall	putc
+
+	mov	a, r7	; sds_index bit
+	acall	wbyte
+	mov	a, r5	; SFR_94 (2 x r5 | r7)
+	acall	wbyte
+	mov	a, r3	; SFR_93
+	acall	wbyte
+
+	mov	a, #':'
+	acall	putc
+
+	mov	a, r1
+	mov	r4, a	; R1 is scratch
+
+	mov	a, r7
+	mov	r1, a
+	mov	a, r5 
+	mov	r7, a 
+
+	ret
+
+;
+; print SDS read result
+;
+sds_read_tail:
+	mov	a, r4
+	mov	r6, a	; R6 is returned and preserved
+
+	mov	a, r7	; = r7 = SFR_DATA_8
+	acall	wbyte
+	mov	r7, SFR_DATA_0
+	mov	a, r7	; SFR_DATA_0
+	acall	wbyte
+
+	mov	a, #' '
+	acall	putc
+
+	mov	a, r6	; R6 is returned and preserved
+	mov	r4, a	
+	ret
+
+;
+;	Write a byte as hex to serial
+;
+	nop
+	nop
+wbyte:
+	mov	r4, a
+	swap	a
+	anl	a, #0x0f
+	mov	dptr,#hex
+	movc	a, @a+dptr
+
+	jb	ET0, wbyte1
+	ret
+wbyte1:
+	jbc	TI, wbyte2
+	sjmp	wbyte1
+wbyte2:
+	mov	SBUF,a
+	
+	mov	a, r4
+	anl	a, #0x0f
+	mov	dptr,#hex
+	movc	a, @a+dptr
+
+wbyte3:
+	jbc	TI, wbyte4
+	sjmp	wbyte3
+wbyte4:
+	mov	SBUF,a
+
+	ret
+
+;
+;	Intercept isr_ext0
+;
+isr_ext0:
+	mov	a, #'i'
+	acall	putc
+	mov	r0,#0x51
+	inc	@r0
+	ret
+
+;
+;	Intercept isr_ext1
+;
+isr_ext1:
+	mov	a, #'I'
+	acall	putc
+	mov	r0,#0x25
+	mov	a, @r0
+	ret
+;
+;	Intercept isr_ext2
+;
+isr_ext2:
+	mov	a, #'J'
+	acall	putc
+	mov	r0, #0x1e
+	mov	a, #0xa
+	ret
+
+;
+;	Intercept isr_ext3
+;
+isr_ext3:
+	mov	a, #'j'
+	acall	putc
+	mov	r0,#0x1e
+	mov	a,#0x14
+	ret
+
+;
+;	Write a character to serial
+;
+	nop
+	nop
+putc:
+	jb	ET0, putc1
+	ret
+putc1:
+	jbc	TI,putc2
+	sjmp	putc1
+putc2:
+	mov	SBUF,a
+	ret
+
+hex:
+	.byte "0123456789abcdef"
+	.end

test/Makefile

@@ -27,7 +27,8 @@ BUILDDIR = build
 TESTS = $(BUILDDIR)/test_cmd_editor \
         $(BUILDDIR)/test_port_tables \
         $(BUILDDIR)/test_page_json \
-        $(BUILDDIR)/test_httpd_tx
+        $(BUILDDIR)/test_httpd_tx \
+        $(BUILDDIR)/test_tick_gate
 
 # The table tests link the register mock and one environment file; stub/
 # stands in for the two headers a firmware build generates.
@@ -47,6 +48,9 @@ $(BUILDDIR)/test_cmd_editor: test_cmd_editor.c support.c $(SRCROOT)/cmd_editor.c
 $(BUILDDIR)/test_port_tables: test_port_tables.c $(TABLE_ENV) hw_mock.h | $(BUILDDIR)
 	$(CC) $(CFLAGS) $(filter %.c,$^) -o $@ $(LDFLAGS)
 
+$(BUILDDIR)/test_tick_gate: test_tick_gate.c support.c $(SRCROOT)/cmd_editor.c | $(BUILDDIR)
+	$(CC) $(CFLAGS) $^ -o $@ $(LDFLAGS)
+
 $(BUILDDIR)/test_page_json: test_page_json.c $(TABLE_ENV) hw_mock.h | $(BUILDDIR)
 	$(CC) $(CFLAGS) $(filter %.c,$^) -o $@ $(LDFLAGS)
 

test/env_tables.c

@@ -84,6 +84,9 @@ char     port_names[9][PORT_NAME_SIZE];
 struct flash_region_t flash_region;
 struct syslog_state syslog_state;
 bool     stp_enabled;
+bool lldp_enabled;
+uint16_t lldp_logical_port_status;
+
 
 uip_ipaddr_t uip_hostaddr, uip_draddr, uip_netmask;
 struct uip_eth_addr uip_ethaddr = { .addr = { 0x02, 0x11, 0x22, 0x33, 0x44, 0x55 } };

test/support.c

@@ -27,6 +27,7 @@ uint8_t                  cmd_available;
 uint8_t                  err_status;
 uint8_t                  cmd_history[CMD_HISTORY_SIZE];
 uint16_t                 cmd_history_ptr;
+__xdata uint16_t         session_timeout = 200;   /* httpd global, referenced by page_impl.c */
 
 /* editor-internal read pointer (defined in cmd_editor.c, external linkage) */
 extern __xdata uint8_t l;

test/test_httpd_tx.c

@@ -139,6 +139,8 @@ void send_status(void) { }
 void send_vlan(uint16_t vlan) { (void)vlan; }
 void send_basic_info(void) { }
 void send_bandwidth(void) { }
+void send_storm(void) { }
+void send_isolation(void) { }
 void send_eee(void) { }
 void send_l2(uint16_t idx) { (void)idx; }
 void l2_delete(uint16_t idx) { (void)idx; }
@@ -150,6 +152,7 @@ void send_lag(void) { }
 void send_stp(void) { }
 void send_stp_counters(void) { }
 void send_vlanlist(void) { }
+void send_lldp(void) {}
 
 extern uint8_t authenticated;
 

test/test_tick_gate.c

@@ -0,0 +1,83 @@
+/*
+ * test_tick_gate.c - the timers of the main loop keep time by the system
+ * tick, however often the loop passes. The gate is the TICKS_DUE macro from
+ * rtl837x_common.h; the loop bodies of idle() and handle_tx() are restated
+ * here, so this checks the arithmetic, not those functions.
+ */
+#include <stdint.h>
+#include <stdio.h>
+
+#include "rtl837x_common.h"
+#include "rtl837x_stp.h"
+#include "support.h"
+
+volatile uint32_t ticks;
+
+#define STP_TICK_STEP (SYS_TICK_HZ / STP_HZ)
+#define STP_CATCH_UP 8
+
+static uint8_t  stp_tick_last, tx_tick_last;
+static unsigned stp_calls, tx_calls;
+
+/* One pass of the loop: the STP block of idle() and the gate of handle_tx() */
+static void pass(void)
+{
+	uint8_t n = STP_CATCH_UP;
+	while (n-- && TICKS_DUE(stp_tick_last, STP_TICK_STEP)) {
+		stp_tick_last += STP_TICK_STEP;
+		stp_calls++;
+	}
+	if (TICKS_DUE(tx_tick_last, 1)) {
+		tx_tick_last = (uint8_t)ticks;
+		tx_calls++;
+	}
+}
+
+/* Run `seconds` of wall clock with one pass every `pass_us` microseconds. */
+static void run(double pass_us, unsigned seconds)
+{
+	double t = 0, next_tick = 0, tick_us = 1e6 / SYS_TICK_HZ, end = seconds * 1e6;
+	ticks = 0;
+	stp_tick_last = tx_tick_last = 0;
+	stp_calls = tx_calls = 0;
+	while (t < end) {
+		while (next_tick <= t) { ticks++; next_tick += tick_us; }
+		pass();
+		t += pass_us;
+	}
+}
+
+static void t_rates(void)
+{
+	printf("[test] STP time follows the tick whatever the loop does\n");
+	run(5000, 10);
+	CHECK(stp_calls == 10 * STP_HZ, "one pass per tick: 500 STP steps in 10 s");
+	CHECK(tx_calls == 10 * SYS_TICK_HZ, "and 2000 TX periodics");
+	run(16000, 10);
+	CHECK(stp_calls >= 10 * STP_HZ - 1 && stp_calls <= 10 * STP_HZ, "a 16 ms pass, as under an IPv4 stream: still 500 (was 156 when the clock counted passes)");
+	CHECK(tx_calls == 625, "TX periodic once per pass when passes are slower than the tick");
+	run(600, 10);
+	CHECK(stp_calls == 10 * STP_HZ, "a 0.6 ms pass, the loop no longer sleeping: still 500 (was 4166)");
+	CHECK(tx_calls == 10 * SYS_TICK_HZ, "TX periodic capped at the tick rate");
+	run(1300000, 13);
+	CHECK(stp_calls <= 10 * STP_CATCH_UP, "a 1.3 s pass loses time instead of firing 65 steps at once");
+}
+
+static void t_wrap(void)
+{
+	printf("[test] the byte arithmetic survives the tick counter wrapping\n");
+	ticks = 0xfffffffeUL;
+	stp_tick_last = (uint8_t)ticks;
+	stp_calls = 0;
+	for (int i = 0; i < 8; i++) { ticks++; pass(); }
+	CHECK(stp_calls == 2, "two STP steps across 0xffffffff -> 0x00000006");
+}
+
+int main(void)
+{
+	printf("== tick gate tests ==\n");
+	t_rates();
+	t_wrap();
+	printf("\n%d checks, %d failed\n", tests_run, tests_failed);
+	return tests_failed ? 1 : 0;
+}

tools/fileadder.c

@@ -338,15 +338,16 @@ int main(int argc, char **argv)
 	if (stat(arguments.data_file, &s) == 0 && s.st_mode & S_IFDIR) {
 		printf("Adding entries in directory %s\n", arguments.data_file);
 		addsDir = true;
-		DIR *dirptr = opendir(arguments.data_file);
-		if (!dirptr) {
+		struct dirent **entries;
+		int n_entries = scandir(arguments.data_file, &entries, NULL, alphasort);
+		if (n_entries < 0) {
 			fprintf(stderr, "%s: ", arguments.data_file);
 			perror("Error opening directory");
 			return 5;
 		}
-		struct dirent *in_file;
 		int addr = arguments.address;
-		while ( (in_file = readdir(dirptr)) )  {
+		for (int e = 0; e < n_entries; e++)  {
+			struct dirent *in_file = entries[e];
 			snprintf(pathbuffer, PATH_SIZE, "%s/%s", arguments.data_file, in_file->d_name);
 			if (stat(pathbuffer, &s) < 0) {
 				fprintf(stderr, "%s: ", pathbuffer);
@@ -377,6 +378,9 @@ int main(int argc, char **argv)
 			addidx(in_file->d_name, addr, data_read);
 			addr += data_read;
 		}
+		for (int e = 0; e < n_entries; e++)
+			free(entries[e]);
+		free(entries);
 	} else {
 		size_t data_read = addfile(arguments.data_file, arguments.address);
 
@@ -437,7 +441,7 @@ int main(int argc, char **argv)
 		fputs(xbuf, ofile);
 		fputs(fbuf, ofile);
 		fclose(ofile);
-	} else if (addsDir){
+	} else if (addsDir && !argv[arg_index]) {
 		puts(dbuf);
 		puts(xbuf);
 		puts(ibuf);

tools/httpd_sim.c

@@ -447,13 +447,41 @@ void send_mtu(int s)
 		json_object_object_add(v, "mtu", json_object_new_string(mtu));
 		json_object_array_add(mtus, v);
 	}
-        write(s, header, strlen(header));
+	write(s, header, strlen(header));
 
 	jstring = json_object_to_json_string_ext(mtus, JSON_C_TO_STRING_PLAIN);
         write(s, jstring, strlen(jstring));
 	json_object_put(mtus);
 }
 
+void send_lldp(int s)
+{
+	struct json_object *c, *portStatuses, *p;
+	const char *jstring;
+	char *header = "HTTP/1.1 200 OK\r\n"
+                         "Content-Type: application/json; charset=UTF-8\r\n\r\n";
+
+	c = json_object_new_object();
+	json_object_object_add(c, "on", json_object_new_int(1));
+	portStatuses = json_object_new_array_ext(PORTS);
+
+	for (int i = 1; i <= PORTS; i++) {
+		p = json_object_new_object();
+		json_object_object_add(p, "portNum", json_object_new_int(i));
+		json_object_object_add(p, "logPort", json_object_new_int(i-1));
+		json_object_object_add(p, "name", json_object_new_string(""));
+		json_object_object_add(p, "permitted", json_object_new_int(1));
+		json_object_array_add(portStatuses, p);
+	}
+
+	json_object_object_add(c, "portStatus", portStatuses);
+
+	write(s, header, strlen(header));
+
+	jstring = json_object_to_json_string_ext(c, JSON_C_TO_STRING_PLAIN);
+	write(s, jstring, strlen(jstring));
+	json_object_put(c);
+}
 
 void send_cmd_log(int s)
 {
@@ -468,7 +496,6 @@ void send_cmd_log(int s)
 	}
 }
 
-
 void send_config(int s)
 {
         char *header = "HTTP/1.1 200 OK\r\n"
@@ -701,6 +728,13 @@ void launch(struct Server *server)
 					else
 						send_vlan(new_socket, vlan);
 					goto done;
+				} else if (!strncmp(&buffer[4], "/lldp.json", 10)) {
+					printf("LLDP request");
+					if (!authenticated)
+						send_unauthorized(new_socket);
+					else
+						send_lldp(new_socket);
+					goto done;
 				} else if (!strncmp(&buffer[4], "/cmd_log", 8)) {
 					printf("Request cmd_log\n");
 					if (!authenticated)

tools/httpd_sim.h

@@ -3,7 +3,7 @@
 
 #include <netinet/in.h>
 
-#define BUFFER_SIZE 131072
+#define BUFFER_SIZE 262144
 
 struct Server {
     int domain;

uip/uip-fw.c

@@ -64,6 +64,8 @@
 
 #include "../rtl837x_common.h"
 
+#if UIP_FORWARDING
+
 /*
  * The list of registered network interfaces.
  */
@@ -535,3 +537,5 @@ uip_fw_periodic(void)
   }
 }
 /*------------------------------------------------------------------------------*/
+
+#endif /* UIP_FORWARDING */

uip/uip-neighbor.c

@@ -43,6 +43,8 @@
 #include "uip-neighbor.h"
 #include "../rtl837x_common.h"
 
+#if UIP_CONF_IPV6
+
 #pragma codeseg BANK1
 #pragma constseg BANK1
 
@@ -170,3 +172,5 @@ uip_neighbor_lookup(__xdata uip_ipaddr_t ipaddr)
   return NULL;
 }
 /*---------------------------------------------------------------------------*/
+
+#endif /* UIP_CONF_IPV6 */

uip/uipopt.h

@@ -464,6 +464,20 @@ extern __xdata uint8_t uip_buf[UIP_CONF_BUFFER_SIZE+2];
 #define UIP_BROADCAST UIP_CONF_BROADCAST
 #endif /* UIP_CONF_BROADCAST */
 
+/**
+ * Build the IP forwarding module.
+ *
+ * uip-fw.c forwards packets between several network interfaces. A
+ * single-interface device does not call it and should not pay for it.
+ *
+ * \hideinitializer
+ */
+#ifndef UIP_CONF_FORWARDING
+#define UIP_FORWARDING 0
+#else /* UIP_CONF_FORWARDING */
+#define UIP_FORWARDING UIP_CONF_FORWARDING
+#endif /* UIP_CONF_FORWARDING */
+
 /**
  * Print out a uIP log message.
  *