A reserved-multicast trap goes to the port named in EXT_CPU_CTRL, which
names no port out of reset, so trapped frames were dropped at ingress.
trap_init() points it at the CPU port once at startup, and
trap_rma_set() changes only the action field of an RMA register.
A trapped frame arrives without the VLAN tag a forwarded one gets, so
TRAP_RX_BODY() gives the offset of the payload for both forms.
STP now traps its address while it runs instead of steering it with a
static L2 entry per VLAN, so turning it on no longer walks the VLAN
table and a pvid change no longer needs stp off and on. With STP off
the flooding entries are restored as before.
A trapped BPDU passes the tagged-only ingress filter that drops a
forwarded one, so the stp_setup() warning about such ports goes.
The answer to a lookup arrives after the command has returned, so the
console of the web interface never shows it. Plain "dns" now prints the
name and the address, or whether it is still pending or failed.
The V3.2 board has the same component placement as V3.1 and works with
its machine definition: RJ45 links at 2.5G, LEDs, SFP detection with DOM
readings at 10G, factory MAC at 0x1FC000 and the reset button. The new
target only reports "V3.2" as the machine name.
Installed from the original firmware V100.9.25 through its web
interface with the OEM installer image. Reading the flash in-circuit with
a SOIC-8 clip gave the chip ID EF FF FF, as on a V3.1 board.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Only frames to 01:00:5e:00:00:16 reached the IGMP handler, so v1/v2
reports, which go to the group address, were never seen. The handler
also took the group from the first v3 group record for every type.
Pass all IPv4 multicast to the handler, which takes the IGMP header
from the IP header length, the group from the IGMP header for v1/v2
reports and v2 leaves and from the first group record for v3, and
returns 0 for anything that is not IGMP so it goes on to the IP stack.
The message and record types have names now.
Storm control used meters 0 to 39, the same meters the ACL hands out,
so a storm limit and an acl meter could overwrite each other. It now
uses 24 + port * 4 + type, meters 24 to 63.
parse_storm() is no longer reentrant and uses plain locals, looks the
type up in a while loop and returns straight from the one-line cases.
storm_show() uses plain locals too.
The documentation says how IGMP decides between mcast and umcast, how
to get from a meter index to its limit, where the IFG bit of a meter
is, and what an ingress bandwidth limit on the same port does to the
storm limit.
The switch has no battery backed clock, only a seconds counter that starts
at zero on every boot. An SNTP client keeps UTC as the time of the last
answer plus the seconds counted since: "ntp server <name|ip>", "ntp interval
<minutes>", "ntp timezone <+hh:mm>", "ntp dst off|eu|us", "ntp on|off",
"ntp" and "time". A server given by name goes through the DNS resolver, an
answer from an unsynchronised server is ignored, and a failed attempt is
repeated after 30 seconds.
The local time adds the time zone offset and, while the European or United
States rule says so, one hour. The date is split with a shift and subtract
division and a walk over the years, so no 32-bit division from the library
ends up in the common area.
The System page gets the NTP settings and shows the local time.
A small resolver for IPv4 address records, so that clients such as NTP can
be given a host name: "dns server <ip> [<ip>]", "dns lookup <name>" and
"dns". Without a configured server it uses the one DHCP handed out. A query
goes to the servers in turn every two seconds and gives up after six tries;
answers with compressed names and CNAME records ahead of the address are
understood. A name that already is a dotted address is taken without a
query.
The resolver sits in BANK3, the command line in BANK2 next to the helpers it
uses. The System page shows and sets the servers.
Add support for the F7008-2.5 board (PCB F7008-2.5GPOE-V1.2), an
RTL8373N + RTL8224N design with eight 2.5GBASE-T ports and one SFP+ cage.
The LED pads are not wired in port order, so the generic DEFAULT_8C_1SFP
target lights the wrong lamp on this board. The pad to lamp map was
measured on the hardware and is documented in doc/devices/F7008-2.5.md.
The green lamp marks a 2.5G link, the yellow lamp blinks while data flows.
The counters, the phase hooks in idle() and the "health" command are now
behind HEALTH, set from the command line with HEALTH=1. Without it the
hooks are empty macros and the command does not exist, so a default build
carries none of it: on SWTGW218AS that is 1065 bytes of bank 2, 101 of the
common segment and 28 of xdata, plus seven banked calls per main-loop pass.
It is a developer's tool. Reading the dump takes knowing the main loop, and
a user who needs it for a report can build with the flag on, which is how
the kernel treats its lock and latency instrumentation as well.
What each line of the dump means, how two dumps give rates, and the
two things worth knowing before trusting the numbers: the command
inflates its own cmd phase counters by the cost of printing, and the
untouched figure is a high-water mark, not a live level.
The header carried the save button, the language selector and the theme
selector on every section, although the latter two are set once. They
now live in a Display card in the System section; the header keeps the
title, the unsaved-changes badge and Save to flash.
Review of #397 pointed at the bare 10, which shows up in fifteen places. It
is the width of the port field in the MSTP register, so it is the CPU port
index plus one and it gets a name.
The web page counted to ten as well when listing a group's members. It uses
numPorts now, like the rest of that page does.
The aggregation section of the doc no longer names the OEM firmware or calls
a group a trunk, and it says plainly that the hardware keeps no per-group
state, so the firmware writes the members itself.
Generated code is unchanged: the only difference in the assembly is the
version string.
Spanning tree so far saw only physical ports. Two ports aggregated towards
the same neighbour look to the protocol like two parallel paths, so it
blocks one of them and cuts the group in half.
Give each of the four groups an STP entity of its own, numbered above the
physical ports. A member port answers to its group: BPDUs arriving on it
are accounted to the entity, the entity's state is written to every member
together, and its BPDUs carry the state of a live member. Ports outside
any group keep behaving exactly as before.
Membership comes from the aggregation tables once a second; when it
changed, the entity's state is reapplied to the new set of members. The
CLI takes lag <1-4> wherever it takes port <n>, the web UI shows a group
as one row, and the saved config keeps the lag form of the commands.
Fold the "group with no ports" case into the argument-count guard
(cmd_words_len < 3) instead of a separate check, and accept only "d" for
delete, dropping the longer "delete" spelling. Update the serial-console
docs to match.
DrDoof
Andreas Erhard
René van Dorst
logicog
Brunoz78andClaude Opus 5.5
Oden
polyfaces
feelfree69
笙笙宝宝
Sylwester Petela
Andreas Erhard
Rob Emery
bloqaudio
David Warren
bennydiamond
eraiza0816