The V3.2 board has the same component placement as V3.1 and works with
its machine definition: RJ45 links at 2.5G, LEDs, SFP detection with DOM
readings at 10G, factory MAC at 0x1FC000 and the reset button. The new
target only reports "V3.2" as the machine name.
Installed from the original firmware V100.9.25 through its web
interface with the OEM installer image. Reading the flash in-circuit with
a SOIC-8 clip gave the chip ID EF FF FF, as on a V3.1 board.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Add support for the F7008-2.5 board (PCB F7008-2.5GPOE-V1.2), an
RTL8373N + RTL8224N design with eight 2.5GBASE-T ports and one SFP+ cage.
The LED pads are not wired in port order, so the generic DEFAULT_8C_1SFP
target lights the wrong lamp on this board. The pad to lamp map was
measured on the hardware and is documented in doc/devices/F7008-2.5.md.
The green lamp marks a 2.5G link, the yellow lamp blinks while data flows.
This PCB is used in RY-8GT-1SX. The UART has swapped Rx and 3.3V VCC as
documented in `doc/devices/FG-8GT-1SX.md` so I imagine there would be
a revision later, after the current '2622' batch, like the RY-4GT-2SX /
FG-4GT-2SX_V2.0 pair from the same vendor.
This PCB appears only slightly different to the already supported and
documented PCB-SWTG115AS-V2.0. It works without any changes to the
machine definition.
While at it, also fix a typo (8272 instead of 8372), and include the
existing unused pictures on the device page.
* add MACHINE_SWTG024AS_A_2_0_1_5_RJ45
* fix(machine): update SFP port LED color descriptions for PCB-SWTG024AS V2.0
* add(doc): create a simple documentation for SWTG024AS-A-V2.0.1_5_RJ45
* refactor(machine): update machine definition
The ZX310S-4T2XT is a managed device with 2x2.5GBit and 2x10GBit Ethernet.
It is sold, among others, by Horaco as an unbranded device.
CPU: RTL8372
Flash: 2MByte Winbond W25Q16DV (U3)
PHY 2x RTL8261BE
I recently brought a "Ztyuav Z-QWYT0402", the insides looked identical to the
existing supported "Hisource Hi-K0402WS". Both of them have the
"PCB-K0402-V3.0" silkscreen.
I flashed the vanilla image and it seems to work great.
I changed the documentation to be more inclusive of other devices (including
adding a picture of mine). I suspect more devices might fall into this
"PCB-K0402-V3.0" bucket, for example the "YuanLey YS25-0402" with
the vlan switch also looks suspiciously identical from the outside.
I also added some details I noticed while flashing mine:
teardown, flash padding, how the selector switch actually works.
Andreas Erhard
Brunoz78andClaude Opus 5.5
Oden
polyfaces
笙笙宝宝
Sylwester Petela
René van Dorst
David Warren
bennydiamond
Pietro AmeruosoandPietro Ameruoso
eeeple
Guoxin Pu
Jan Hoffmann
donbernhardo
Priit Laes
ZYT
Lynn-Becky
Your Name
Ron
th0m4sek
HL Yi
feelfree69
logicog
Alexandru M Stan