mirror of
https://github.com/logicog/RTLPlayground.git
synced 2026-10-29 17:54:14 +08:00
75 lines
2.6 KiB
Markdown
75 lines
2.6 KiB
Markdown
# Hasivo S1100WP-8GT-1SX-SE
|
||
|
||
RTL8373-based 8×2.5G PoE + 1×SFP switch.
|
||
|
||
### Label specifications
|
||
|
||
- **Manufacturer**: Hasivo
|
||
- **Model**: S1100WP-8GT-1SX-SE
|
||
- **Ports**:
|
||
- 8 × RJ45: 10/100/1000/2500 Mbps with PoE
|
||
- 1 × SFP: 1G / 2.5G / 10G
|
||
- **Power input**: DC 52V 2.5A
|
||
- **Stock firmware defaults**: IP 192.168.0.1, user/password `admin`/`admin`
|
||
|
||
### What works
|
||
|
||
- All eight 2.5GBASE-T RJ45 ports at 10/100/1000/2500 Mbps (PoE is not configurable via RTLPlayground)
|
||
- SFP port supporting 1G, 2.5G and 10G modules
|
||
- LEDs: green (2.5G) and amber (1G/100M/10M) per copper port; combined link/act on the SFP port
|
||
|
||
### Photos
|
||
|
||
Front panel:
|
||
|
||
<img src="photos/HASIVO_S1100WP-8GT-1SX-SE/front.jpg" width="600" />
|
||
|
||
Label:
|
||
|
||
<img src="photos/HASIVO_S1100WP-8GT-1SX-SE/label.jpg" width="600" />
|
||
|
||
### PCB overview
|
||
|
||
Top side:
|
||
|
||
<img src="photos/HASIVO_S1100WP-8GT-1SX-SE/pcb_top.jpg" width="600" />
|
||
|
||
Bottom side:
|
||
|
||
<img src="photos/HASIVO_S1100WP-8GT-1SX-SE/pcb_bottom.jpg" width="600" />
|
||
|
||
### Port layout
|
||
|
||
| Logical port | Physical port | Type |
|
||
|--------------|---------------|--------|
|
||
| 1-8 | 1-8 | Copper |
|
||
| 9 | 9 | SFP |
|
||
|
||
### LED configuration
|
||
|
||
Copper ports use LED SET0, the SFP port uses LED SET1.
|
||
|
||
| SET | LED0 | LED2 |
|
||
|------|-----------------------------------------------|------------------------------------------------------|
|
||
| SET0 | Green — lights on 2.5G link with activity | Amber — lights on 1G / 100M / 10M link with activity |
|
||
| SET1 | All speeds — lights on any link with activity | — |
|
||
|
||
### SFP GPIO assignments
|
||
|
||
| SFP (logical 9) | pin_detect (ModAbs) | pin_los | pin_tx_disable | SerDes | I2C SDA | I2C SCL |
|
||
|-----------------|---------------------|---------|----------------|--------|-----------------|---------------------|
|
||
| SFP | GPIO30_ACL_BIT3_EN | GPIO37 | GPIO_NA | SDS1 | GPIO39_I2C_SDA4 | GPIO40_I2C_SCL3_MDC1 |
|
||
|
||
### Machine configuration
|
||
|
||
- `reset_pin`: GPIO54_ACL_BIT2_EN
|
||
- High LEDs (pads 27-29): mux = `LED_27 | LED_28_SYS | LED_29`, enable = `LED_28_SYS | LED_29`
|
||
|
||
### PoE
|
||
|
||
The 8 copper ports support PoE powered by a DC 52V 2.5A input. Power management is handled by two HS104PTI chipsets over I2C (GPIO47_I2C_SDA0, GPIO46_I2C_SCL0):
|
||
|
||
* Chip 1 (I2C address 0x1A): 2.5G Ports 1–4
|
||
* Chip 2 (I2C address 0x2A): 2.5G Ports 5–8
|
||
|
||
Note: The current implementation does not yet support PoE management. Consequently, PoE currently operates in standalone mode without software control. |