The hongyavision HYWS-SGT0204S is sold as an unmanaged 4x2.5G + 2x10G SFP+
switch and carries the 2G5F4_10G2_V1.01 marking on the PCB. It is a sibling of
the KP-9000-6XH-X2 (2M-PCB43-V1.1), so machine/2G5F4_10G2_V1_01.c is that board
definition with these changes:
- The two SFP+ cages (physical ports 5 and 6) are wired the other way round:
physical 5 is on SDS1 with GPIO30/GPIO37, physical 6 on SDS0 with
GPIO50/GPIO10. Copper ports 1-4 match the KP-9000 layout.
- No reset button is fitted and the case has no opening for one, so reset_pin
is GPIO_NA. GPIO54, the reset pin on the KP-9000 layout, reads as permanently
pressed here.
- The board definition sets flash_sio, so the flash is read with single-IO: the
fitted 512 KB Bright Moon T25S40 cannot be read in DIO mode on this board, an
image that leaves DIO enabled does not come up at all, while the same image
with single-IO boots and runs normally (two units).
- The board is added to the machine_custom_init() group that sets
LED_GLB_IO_EN bit 6, otherwise the RTL837x "solid" conditions (LINK/speed)
never drive the LEDs and the 2.5G LED glows faintly at 100M/1000M.
flash_sio is a new field of struct machine that rtlplayground.c hands to
flash_init(); only this board sets it, every other machine keeps DIO. It costs
management-plane speed only, the ASIC keeps forwarding in hardware.
The stock firmware runs a factory test console on the serial header at 9600
baud, whose silkscreen labels are shifted by one pin.
Verified: warning-free build, `make machine_check` passes for every target, the
host tests pass, and a control build of this target without the LED hook differs
from the KP-9000-6XH_X2_V1_1 image in 44 bytes: all inside the machine
description (including flash_sio) and the image CRC16, nothing else in the
firmware moved. On the board the single-IO image boots and runs on two units;
port order, SFP cages and LED behaviour come from the machine definition
verified on this board earlier.
The V3.2 board has the same component placement as V3.1 and works with
its machine definition: RJ45 links at 2.5G, LEDs, SFP detection with DOM
readings at 10G, factory MAC at 0x1FC000 and the reset button. The new
target only reports "V3.2" as the machine name.
Installed from the original firmware V100.9.25 through its web
interface with the OEM installer image. Reading the flash in-circuit with
a SOIC-8 clip gave the chip ID EF FF FF, as on a V3.1 board.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Add support for the F7008-2.5 board (PCB F7008-2.5GPOE-V1.2), an
RTL8373N + RTL8224N design with eight 2.5GBASE-T ports and one SFP+ cage.
The LED pads are not wired in port order, so the generic DEFAULT_8C_1SFP
target lights the wrong lamp on this board. The pad to lamp map was
measured on the hardware and is documented in doc/devices/F7008-2.5.md.
The green lamp marks a 2.5G link, the yellow lamp blinks while data flows.
We can reduce the i2c-settings to just one byte, and this new const value
can directly be used by the I2C-peripheral without additional computation.
This saves 1-xdata load and a lot of bit-shifting.
I see a codesize savings of +200 bytes.
Building the firmware headers on the host showed two warnings from
machine.h: `typedef struct machine { ... };` and the same for
machine_runtime declare no alias, so the keyword only draws "useless
storage class specifier in empty declaration". Every user says
`struct machine`, so drop the keyword.
-Wno-builtin-declaration-mismatch is a gcc switch and clang reports it
as an unknown option on every build; add it only when the compiler is
not clang.
This PCB is used in RY-8GT-1SX. The UART has swapped Rx and 3.3V VCC as
documented in `doc/devices/FG-8GT-1SX.md` so I imagine there would be
a revision later, after the current '2622' batch, like the RY-4GT-2SX /
FG-4GT-2SX_V2.0 pair from the same vendor.
machine_custom_init() runs once at boot, but its code and any tables it
uses were compiled into machine.c and so into the common bank. On the
SWTG018AS-V2.1.0 variant, whose init carries a 21-entry LED register
table, that overflows bank 0 by 0x66 bytes and main no longer links for
MACHINE_PCB_SWTG018AS_V2_1_0; any machine whose init grows can hit the
same wall. SDCC segment pragmas apply file-wide, so the hooks move to a
new machine_init.c compiled into BANK2, and the prototype becomes
banked. machine_check also compiles the new file per machine so the
hooks keep CI syntax coverage.
The SWTGW218AS label covers more than one PCB. On boards with the
SWTG018AS-V2.1.0 silkscreen the SFP module-detect is GPIO38 (no LOS pin
wired) and the LED block is wired differently, including a bi-color SFP
LED (green up to 2.5G, blue at 10G) that the LED-set encoding cannot
express. With the existing MACHINE_SWTGW218AS definition these boards
never detect an SFP module, so an SFP-uplinked switch comes up with no
working uplink.
Add the variant as its own machine define named by the PCB marking,
leaving MACHINE_SWTGW218AS unchanged for boards that match its wiring.
The LED register values are taken from the stock firmware; the PIN_MUX_0
write routes the blue-LED pin to the LED controller, without which no
LED register value can drive it. PIN_MUX_1/2 stay untouched so SFP
detect and i2c remain GPIOs.
Adds an optional per-board mac_flash_offset. When non-zero, RTLPlayground
reads a 6-byte MAC from that flash address and uses it if it is a valid
globally-administered unicast address; otherwise it falls back to the
generated locally-administered MAC. Offset 0 (default for every board)
preserves current behaviour.
Enable it for the SWTGW218AS, whose stock firmware keeps the factory MAC
in nvcfg at 0x1FC000. RTLPlayground images and web upgrades only touch
flash below that region, so the factory MAC survives flashing.
* add MACHINE_SWTG024AS_A_2_0_1_5_RJ45
* fix(machine): update SFP port LED color descriptions for PCB-SWTG024AS V2.0
* add(doc): create a simple documentation for SWTG024AS-A-V2.0.1_5_RJ45
* refactor(machine): update machine definition
The ZX310S-4T2XT is a managed device with 2x2.5GBit and 2x10GBit Ethernet.
It is sold, among others, by Horaco as an unbranded device.
CPU: RTL8372
Flash: 2MByte Winbond W25Q16DV (U3)
PHY 2x RTL8261BE
I recently brought a "Ztyuav Z-QWYT0402", the insides looked identical to the
existing supported "Hisource Hi-K0402WS". Both of them have the
"PCB-K0402-V3.0" silkscreen.
I flashed the vanilla image and it seems to work great.
I changed the documentation to be more inclusive of other devices (including
adding a picture of mine). I suspect more devices might fall into this
"PCB-K0402-V3.0" bucket, for example the "YuanLey YS25-0402" with
the vlan switch also looks suspiciously identical from the outside.
I also added some details I noticed while flashing mine:
teardown, flash padding, how the selector switch actually works.
- machine.c/h: add MACHINE_FNS1200P with verified GPIO assignments for
both SFP ports, LED SET0 (amber 2.5G / green 1G-100M-10M) and SET1
(SFP all-speeds), led_mux from original firmware register dump, and
machine_custom_init() enabling LED_GLB_IO_EN bit 6
- doc/devices/FNS-1200P.md: device overview, port layout, serial
console (S1 three through-holes = UART0 115200 8N1 3.3V),
LED and SFP GPIO tables
- doc/devices/photos/FNS-1200P/: chassis front panel and PCB top photos
- doc/supported_devices.md: add FNS-1200P to the list
GPIO assignments and LED register values were cross-checked between
live GPIO observation (RTLPlayground gpio command) and an original
firmware register dump.
HL Yi
Victor
Andreas Erhard
Brunoz78andClaude Opus 5.5
polyfaces
笙笙宝宝
René van Dorst
SkullyDev
SkullyDev
Sylwester Petela
bennydiamond
bloqaudio
David Warren
Pietro AmeruosoandPietro Ameruoso
Guoxin Pu
donbernhardo
ZYT
Lynn-Becky
feelfree69
logicog
kekopop
Alexandru M Stan
Taiga Ogawa
feelfree69
Mark Captur