The HC-SWTGW218AS is listed only with the SWTG018AS-A V2.0 board, but it
also ships with SWTG118AS-V2.1, the board of the XikeStor SKS3200-8E1X.
That version runs MACHINE=SWTGW218AS: three such switches were flashed
through the OEM web upgrade and work.
Note in the device page that the model name alone does not tell which
firmware to build.
Add the assembled top, front and bottom of the case next to the PCB photos, and
record what the nameplate says (manufacturer, the model description translated
from the Chinese label, 12 V DC 2 A and the serial number format) so a device
can be identified by its label. The top of the case carries no model name.
Also point out where the three console through-holes sit in the top side photo
and note the PWR and SFP1/SFP2 LEDs on the front panel; the case legend for the
copper LEDs reads 1000M/2500M.
The hongyavision HYWS-SGT0204S is sold as an unmanaged 4x2.5G + 2x10G SFP+
switch and carries the 2G5F4_10G2_V1.01 marking on the PCB. It is a sibling of
the KP-9000-6XH-X2 (2M-PCB43-V1.1), so machine/2G5F4_10G2_V1_01.c is that board
definition with these changes:
- The two SFP+ cages (physical ports 5 and 6) are wired the other way round:
physical 5 is on SDS1 with GPIO30/GPIO37, physical 6 on SDS0 with
GPIO50/GPIO10. Copper ports 1-4 match the KP-9000 layout.
- No reset button is fitted and the case has no opening for one, so reset_pin
is GPIO_NA. GPIO54, the reset pin on the KP-9000 layout, reads as permanently
pressed here.
- The board definition sets flash_sio, so the flash is read with single-IO: the
fitted 512 KB Bright Moon T25S40 cannot be read in DIO mode on this board, an
image that leaves DIO enabled does not come up at all, while the same image
with single-IO boots and runs normally (two units).
- The board is added to the machine_custom_init() group that sets
LED_GLB_IO_EN bit 6, otherwise the RTL837x "solid" conditions (LINK/speed)
never drive the LEDs and the 2.5G LED glows faintly at 100M/1000M.
flash_sio is a new field of struct machine that rtlplayground.c hands to
flash_init(); only this board sets it, every other machine keeps DIO. It costs
management-plane speed only, the ASIC keeps forwarding in hardware.
The stock firmware runs a factory test console on the serial header at 9600
baud, whose silkscreen labels are shifted by one pin.
Verified: warning-free build, `make machine_check` passes for every target, the
host tests pass, and a control build of this target without the LED hook differs
from the KP-9000-6XH_X2_V1_1 image in 44 bytes: all inside the machine
description (including flash_sio) and the image CRC16, nothing else in the
firmware moved. On the board the single-IO image boots and runs on two units;
port order, SFP cages and LED behaviour come from the machine definition
verified on this board earlier.
UART is broken out to the unpopulated switch header at the front of the
board.
This isn't quite the same as the V2.0 definition as the system led is
always on, not routed through the CPU.
Additionally, document that the newer revision of the same "YS25-0402"
is supported via the existing PCB-K0402WS-V3.0 target.
The strip no longer wraps. Ports shrink to fit the row and scroll
when they cannot, so the header on a phone stays at two rows. The
strip moves under the title only below 720 px, where it no longer
fits beside it. Drop the unused d_ports strings and the strip title.
The row of port icons lived in a card on the Dashboard, so link
state and speed were out of sight on every other tab. Move it into the
header between the title and the save button, a little smaller, and
poll /status.json whenever the page is open instead of only on the
Dashboard, Ports and Statistics tabs; the existing idle and hidden-tab
gating still pauses it. On narrow screens the strip wraps to its own
row under the title.
The column counts the addresses the switch learns from incoming frames,
so "Connected" suggested a connection it does not show. The translations
follow the words the L2 tab already uses for learned entries.
Save to flash merges the running log into the startup configuration.
Neither its toggle nor its overwrite rules knew "lldp on|off", so every
switch of LLDP added another line: four switches left four lines.
"port <n> lldp permit|block" fell under the rule for "port <n> <speed>",
so setting a port's speed dropped its LLDP setting from the saved
configuration, and the other way round.
"lldp on|off" is now a toggle, and a per-port LLDP setting replaces only
an earlier per-port LLDP setting of that port.
hexvalue[] holds four bytes, but atoi_hex() stored every digit it was
given, so a ninth digit was written past the array into whatever follows
it in xdata. More than eight digits now return 0, as any bad input does.
c - '0' < 10 is computed as an int, so characters below '0' such as '-',
'.' or '/' passed as digits and "-1" came out as 0xdf. The difference is
now taken as uint8_t, so they are rejected.
The button in the header was always drawn as the primary action, on
every page, so it competed with each page's own buttons, for example
the upload button on the Firmware page. It is now a plain button and
turns primary together with the "unsaved changes" badge.
The port tooltip and the port details showed "TX good / bad: 8794 / 0
pkts", which reads as 8794 bad packets. Each counter now has its own
line, labelled as on the Statistics page, and the two strings only that
line used are removed from every language.
"table.t th" sets text-align:left and is more specific than ".num", so
the headers of the counter columns on the dashboard and the statistics
page stayed left-aligned above right-aligned values.
The switch keeps flooding 224.0.0.0/24 with IGMP on, but a report for a
group in that block still made an entry for it, and the entry limited
the group to the ports that reported it. A host announcing mDNS on
224.0.0.251 thereby cut mDNS off from every other port. Such reports
are now ignored, as RFC 4541 asks.
igmp_setup(), which `igmp off` also calls, enabled the lookup of IPv4
multicast in the L2 table. Groups learned while IGMP was on therefore
kept going only to the ports that had reported them, and with reports
no longer trapped nothing updated those entries until a reboot.
The lookup is now enabled in igmp_enable() and disabled in igmp_setup(),
so with IGMP off all IP multicast is flooded again.
Andre Brait
Kamikaze94
João Silva
René van Dorst
HL Yi
Victor
Matt Merhar
feelfree69
Robert Klauco
bloq
d00f
bloqaudio
logicog