Read register 0x0004 on all three tested HC-SWTGW218AS units. Each returned 0x83730000, identifying RTL8373 rather than RTL8373N. Firmware reports 2 MB flash on all three.
Fill in the verified device-table fields and document the non-N/N register distinction. Leave PHY and flash-chip models explicitly unverified.
The HC-SWTGW218AS is listed only with the SWTG018AS-A V2.0 board, but it
also ships with SWTG118AS-V2.1, the board of the XikeStor SKS3200-8E1X.
That version runs MACHINE=SWTGW218AS: three such switches were flashed
through the OEM web upgrade and work.
Note in the device page that the model name alone does not tell which
firmware to build.
UART is broken out to the unpopulated switch header at the front of the
board.
This isn't quite the same as the V2.0 definition as the system led is
always on, not routed through the CPU.
Additionally, document that the newer revision of the same "YS25-0402"
is supported via the existing PCB-K0402WS-V3.0 target.
The V3.2 board has the same component placement as V3.1 and works with
its machine definition: RJ45 links at 2.5G, LEDs, SFP detection with DOM
readings at 10G, factory MAC at 0x1FC000 and the reset button. The new
target only reports "V3.2" as the machine name.
Installed from the original firmware V100.9.25 through its web
interface with the OEM installer image. Reading the flash in-circuit with
a SOIC-8 clip gave the chip ID EF FF FF, as on a V3.1 board.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Add support for the F7008-2.5 board (PCB F7008-2.5GPOE-V1.2), an
RTL8373N + RTL8224N design with eight 2.5GBASE-T ports and one SFP+ cage.
The LED pads are not wired in port order, so the generic DEFAULT_8C_1SFP
target lights the wrong lamp on this board. The pad to lamp map was
measured on the hardware and is documented in doc/devices/F7008-2.5.md.
The green lamp marks a 2.5G link, the yellow lamp blinks while data flows.
This PCB is used in RY-8GT-1SX. The UART has swapped Rx and 3.3V VCC as
documented in `doc/devices/FG-8GT-1SX.md` so I imagine there would be
a revision later, after the current '2622' batch, like the RY-4GT-2SX /
FG-4GT-2SX_V2.0 pair from the same vendor.
This PCB appears only slightly different to the already supported and
documented PCB-SWTG115AS-V2.0. It works without any changes to the
machine definition.
While at it, also fix a typo (8272 instead of 8372), and include the
existing unused pictures on the device page.
- machine.c/h: add MACHINE_FNS1200P with verified GPIO assignments for
both SFP ports, LED SET0 (amber 2.5G / green 1G-100M-10M) and SET1
(SFP all-speeds), led_mux from original firmware register dump, and
machine_custom_init() enabling LED_GLB_IO_EN bit 6
- doc/devices/FNS-1200P.md: device overview, port layout, serial
console (S1 three through-holes = UART0 115200 8N1 3.3V),
LED and SFP GPIO tables
- doc/devices/photos/FNS-1200P/: chassis front panel and PCB top photos
- doc/supported_devices.md: add FNS-1200P to the list
GPIO assignments and LED register values were cross-checked between
live GPIO observation (RTLPlayground gpio command) and an original
firmware register dump.
Andre Brait
HL Yi
Matt Merhar
João Silva
Andreas Erhard
Brunoz78andClaude Opus 5.5
Oden
polyfaces
笙笙宝宝
Sylwester Petela
René van Dorst
David Warren
bennydiamond
Pietro AmeruosoandPietro Ameruoso
eeeple
Guoxin Pu
Jan Hoffmann
donbernhardo
Priit Laes
ZYT
th0m4sek
Taiga Ogawa
diijkstra
logicog