mirror of
https://github.com/logicog/RTLPlayground.git
synced 2026-10-29 17:54:14 +08:00
Brunoz78andClaude Opus 5.5
b71239f394
The V3.2 board has the same component placement as V3.1 and works with its machine definition: RJ45 links at 2.5G, LEDs, SFP detection with DOM readings at 10G, factory MAC at 0x1FC000 and the reset button. The new target only reports "V3.2" as the machine name. Installed from the original firmware V100.9.25 through its web interface with the OEM installer image. Reading the flash in-circuit with a SOIC-8 clip gave the chip ID EF FF FF, as on a V3.1 board. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
113 lines
3.4 KiB
C
113 lines
3.4 KiB
C
#ifndef _MACHINE_H_
|
|
#define _MACHINE_H_
|
|
|
|
#include <stdint.h>
|
|
|
|
/*
|
|
* Select your machine type below
|
|
*/
|
|
// Legacy KP-9000 4+2 targets. Prefer the PCB-revision-specific targets below.
|
|
// #define MACHINE_KP_9000_6XHML_X2
|
|
// #define MACHINE_KP_9000_6XH_X2
|
|
|
|
// KP-9000 4+2 targets by PCB silkscreen revision.
|
|
// #define MACHINE_KP_9000_6XH_X2_V1_1
|
|
// #define MACHINE_KP_9000_6XHML_X2_V1_1
|
|
// #define MACHINE_KP_9000_6XH_X2_V1_2
|
|
// #define MACHINE_KP_9000_6XHML_X2_V1_2
|
|
// #define MACHINE_KP_9000_6XH_X2_V2_1
|
|
// #define MACHINE_KP_9000_6XHML_X2_V2_1
|
|
|
|
// #define MACHINE_KP_9000_6XH_X
|
|
// #define MACHINE_KP_9000_9XH_X_EU
|
|
// #define MACHINE_KP_9000_9XHML_X_V2_2
|
|
// #define MACHINE_KP_9000_9XHML_X_V3_1
|
|
// #define MACHINE_KP_9000_9XHML_X_V3_2
|
|
// #define MACHINE_SWGT024_V2_0_MANAGED
|
|
// #define MACHINE_SWGT024_V2_0_UNMANAGED
|
|
// #define MACHINE_TRENDNET_TEG_S562
|
|
// #define MACHINE_HG0402XG_V1_1
|
|
// #define MACHINE_SWTG018AS_A_V_2_0
|
|
// #define MACHINE_SWTGW218AS
|
|
// #define MACHINE_PCB_SWTG018AS_V2_1_0
|
|
// #define MACHINE_PCB_K0402WS_V3
|
|
// #define MACHINE_PCB_K0402WS_V2
|
|
// #define MACHINE_K0501W_V2_0
|
|
// #define MACHINE_LIANGUO_ZX_SWTGW215AS
|
|
// #define MACHINE_ZX310S_4T2XH
|
|
// #define MACHINE_ZX310S_4T2XT
|
|
// #define MACHINE_STEAMEMO_IG204_V1
|
|
// #define MACHINE_DEFAULT_8C_1SFP
|
|
// #define MACHINE_HI_K0801WS
|
|
// #define MACHINE_FNS1200P
|
|
// #define MACHINE_PCB_SWTG024AS_A_2_0_1
|
|
// #define MACHINE_SWTG024AS_A_2_0_1_5C_1SFP
|
|
// #define MACHINE_SWTG024AS_V2_0
|
|
// #define MACHINE_FG_4GT_2SX_V2_0
|
|
// #define MACHINE_FG_8GT_1SX
|
|
// #define MACHINE_LIANGUO_HYWS_SGT0108S
|
|
// #define MACHINE_POE_2G080110GS
|
|
// #define MACHINE_PB_2132
|
|
// #define MACHINE_HASIVO_S600W_4GT_2XGT_SE
|
|
// #define MACHINE_HASIVO_S1100WP_8GT_1SX_SE
|
|
// #define MACHINE_F7008_2_5
|
|
|
|
#define LED_27 1
|
|
// SYSTEM LED
|
|
#define LED_28_SYS 2
|
|
#define LED_29 4
|
|
|
|
struct high_leds {
|
|
// Defines MUX and LED enabling for pins 27-29
|
|
uint8_t mux : 3;
|
|
uint8_t enable : 3;
|
|
uint8_t reserved : 2;
|
|
};
|
|
|
|
struct sfp_port
|
|
{
|
|
uint8_t pin_detect; // gpio number 0-63, 0xFF = don't have it?
|
|
uint8_t pin_los; // gpio number 0-63, 0xFF = don't have it?
|
|
uint8_t pin_tx_disable; // gpio number 0-63, 0xFF = not present
|
|
uint8_t sds;
|
|
uint8_t i2c;
|
|
};
|
|
|
|
struct machine {
|
|
char machine_name[30];
|
|
uint8_t isRTL8373;
|
|
// Lowest logical port number
|
|
uint8_t min_port;
|
|
// Highest logical port number
|
|
uint8_t max_port;
|
|
uint8_t n_sfp;
|
|
uint8_t n_10g;
|
|
uint8_t log_to_phys_port[9];
|
|
uint8_t phys_to_log_port[9]; // Starts at 0 for port 1
|
|
uint8_t is_sfp[9]; // 0 for non-SFP ports 1 or 2 for the I2C port number
|
|
// sfp_port[0] is the first SFP-port from the left on the device, sfp_port[1] the next if present
|
|
struct sfp_port sfp_port[2];
|
|
uint8_t reset_pin;
|
|
struct high_leds high_leds;
|
|
// Defines which led-set (0-3) will be used for given logical port
|
|
// led-set is physical group of LEDs that can be configured to show different port status combinations (see port_led_set below)
|
|
uint8_t port_led_set[9];
|
|
// Defines led-set configuration, applied to all ports using particular led-set
|
|
// Each led-set can have 4 different hardware LED configurations. Which one should be used, depends how LED is wired on the board
|
|
// See stock RTL837X_REG_LED3_2_SETx and RTL837X_REG_LED1_0_SETx registers for reference configuration
|
|
uint32_t led_sets[4][4];
|
|
uint8_t led_mux_custom;
|
|
uint8_t led_mux[28];
|
|
uint32_t mac_flash_offset;
|
|
};
|
|
|
|
struct machine_runtime
|
|
{
|
|
uint8_t isRTL8373 : 1;
|
|
uint8_t isN : 1;
|
|
};
|
|
|
|
void machine_custom_init(void) __banked;
|
|
|
|
#endif
|