mirror of
https://github.com/logicog/RTLPlayground.git
synced 2026-08-30 14:52:51 +08:00
61 lines
1.9 KiB
Markdown
61 lines
1.9 KiB
Markdown
# SWTG018AS-A V2.0
|
||
## Brands
|
||
| Brand | Type |Managed| PCB | Flash | Chip RTL |
|
||
|--------|------------------|-------|------------------|-----------------|---------------|
|
||
| Ampcom | SWTG018AS-A V2.0 | No | SWTG018AS-A V2.0 | 2MB | 8273N + 8224N |
|
||
| Horaco | HC-SWTGW218AS-A | Yes | SWTG018AS-A V2.0 | 2MB(25Q16JVSIQ) | 8273N + 8224N |
|
||
|
||
|
||
The following is a documentation for the unmanaged switch marked as `SWTG018AS-A V2.0`.
|
||
It is e.g. sold under the Ampcom brand, but no branh-markings are found on the device.
|
||
|
||
The original software is running UART on 9600 baud rate.
|
||
|
||
Using a SOIC clamp in-board is the only method for initial installation.
|
||
|
||
The board has a single flash chips `BS` with 4M-bit size. The front switch, switches between the two flash chips.
|
||
These can be programed independently by using said switch - so it is e.g. possible to run the original and new firmware in parallel.
|
||
|
||
### Label specifications
|
||
|
||
- **Name**: 9-Ports 2.5G Ethernet Switch
|
||
- **Ports**:
|
||
- 8 × RJ45: 10/100/1000/2500 Mbps
|
||
- 1 × SFP+: 1000 / 2500 / 10000 Mbps
|
||
- **Power**: 12V DC, 1A barrel connector
|
||
|
||
<img src="photos/SWTG018AS_A_V_2_0/label.jpg" width="300" />
|
||
|
||
### What works
|
||
The device is fully supported:
|
||
- All 8 2.5GBASE-T RJ45 ports work at 10/100/1000/2500 Mbps
|
||
- The SFP+ port supports 1G, 2.5G and 10G modules
|
||
- LEDs work with the same indiciations as the OEM firmware
|
||
|
||
### PCB overview
|
||
|
||
**Board markings**
|
||
- Top silkscreen: SWTG018AS-A-V2.0.1_19649
|
||
|
||
Top side
|
||
|
||
<img src="photos/SWTG018AS_A_V_2_0/pcb_top.jpg" width="300" />
|
||
|
||
Bottom
|
||
|
||
<img src="photos/SWTG018AS_A_V_2_0/pcb_bottom.jpg" width="300" />
|
||
|
||
### J1, serial console
|
||
|
||
| `J1` pin | Signal |
|
||
| -------- | ----------- |
|
||
| 1 | 3V3 |
|
||
| 2 | GND |
|
||
| 3 | RX (Input) |
|
||
| 4 | TX (Output) |
|
||
|
||
|
||
## Power supply
|
||
|
||
Input power is delivered via barell plug, `12V 1A` adapter was provided.
|