mirror of
https://github.com/logicog/RTLPlayground.git
synced 2026-10-29 17:54:14 +08:00
Victor
389dc2af76
The hongyavision HYWS-SGT0204S is sold as an unmanaged 4x2.5G + 2x10G SFP+ switch and carries the 2G5F4_10G2_V1.01 marking on the PCB. It is a sibling of the KP-9000-6XH-X2 (2M-PCB43-V1.1), so machine/2G5F4_10G2_V1_01.c is that board definition with these changes: - The two SFP+ cages (physical ports 5 and 6) are wired the other way round: physical 5 is on SDS1 with GPIO30/GPIO37, physical 6 on SDS0 with GPIO50/GPIO10. Copper ports 1-4 match the KP-9000 layout. - No reset button is fitted and the case has no opening for one, so reset_pin is GPIO_NA. GPIO54, the reset pin on the KP-9000 layout, reads as permanently pressed here. - The board definition sets flash_sio, so the flash is read with single-IO: the fitted 512 KB Bright Moon T25S40 cannot be read in DIO mode on this board, an image that leaves DIO enabled does not come up at all, while the same image with single-IO boots and runs normally (two units). - The board is added to the machine_custom_init() group that sets LED_GLB_IO_EN bit 6, otherwise the RTL837x "solid" conditions (LINK/speed) never drive the LEDs and the 2.5G LED glows faintly at 100M/1000M. flash_sio is a new field of struct machine that rtlplayground.c hands to flash_init(); only this board sets it, every other machine keeps DIO. It costs management-plane speed only, the ASIC keeps forwarding in hardware. The stock firmware runs a factory test console on the serial header at 9600 baud, whose silkscreen labels are shifted by one pin. Verified: warning-free build, `make machine_check` passes for every target, the host tests pass, and a control build of this target without the LED hook differs from the KP-9000-6XH_X2_V1_1 image in 44 bytes: all inside the machine description (including flash_sio) and the image CRC16, nothing else in the firmware moved. On the board the single-IO image boots and runs on two units; port order, SFP cages and LED behaviour come from the machine definition verified on this board earlier.
7.1 KiB
7.1 KiB
Supported Hardware
The following devices have been tested and are fully working:
| Brand | Type | Managed | PCB | Flash | Ports |
|---|---|---|---|---|---|
| Ampcom | WAM902-SWTG018AS | No | SWTG018AS-A V2.0 | 8 + 1 | |
| Davuaz | Da-K6501W | No | PCB-K0501W-V2.0 | 5 + 1 | |
| FOXNEO | FNS-1200P | No | PCB-K0402W-U13-V2.0 | 2M | 4 + 2 |
| Goalake | IG108 | No | PB-2132 | 4M | 8 + 1 |
| GoodTop | GT-ST018M | Yes | SWTG018AS-A V2.0 | ? | 8 + 1 |
| GoodTop | GT-ST024M | Yes | SWTG024AS-A V2.0.1 | 2M | 4 + 2 |
| Hasivo | S1100WP_8GT_1SX_SE | Yes | S1100WP_8GT_1SX_SE-V1.05 | 2M | 8 + 1 |
| Hisource | Hi-K0402WS | No | PCB-K0402WS-V3.0 | 4 + 2 | |
| Hisource | Hi-K0402WS | No | PCB-K0402WS-V2.0 | 2M | 4 + 2 |
| Hisource | Hi-K0801WS | No | PCB-KO801W-V2.0 | 8 + 1 | |
| hongyavision | HYWS-SGT0204S | No | 2G5F4_10G2_V1.01 | 0.5M | 4 + 2 |
| hongyavision | LG-SG5T1 | No | PCB-SWTG024AS-V2.0_16895 | 0.5M | 5 + 1 |
| Horaco | HC-SWTGW215AS | Yes | SWTG024AS-A-V2.0.1_19650 5C 1SFP | ? | 5 + 1 |
| Horaco | HC-SWTGW218AS | Yes | SWTG018AS-A V2.0 | 8 + 1 | |
| Horaco | ZX310S-4T2XH | Yes | PCB-SL310S-4T1T1X-V1.0.1-24107 | 2M | 5 + 1 |
| Horaco | ZX310S-4T2XT | Yes | PCB-SL310S-4T2XT-V1.0.0-22273 | 2M | 6 |
| Horaco | ZX-SG4T2 | No | SWTG024AS-A-V2.0.1_19650_4C_2SFP | 0.5M | 4 + 2 |
| Horaco | ZX-SWTG124AS | Yes | SWTG024AS-v2.0 | 4 + 2 | |
| Keeplink | KP-9000-6XH-X2 / KP-9000-6XHML-X2 | No/Yes | 2M-PCB43-V1.2 / V2.1 | 4 + 2 | |
| keepLINK | KP-9000-9XHML-X | Yes | 2M-PCB23-V2.2 | 2M | 8 + 1 |
| keepLINK | KP-9000-9XHML-X | Yes | 2M-PCB23-V3.1 | 2M | 8 + 1 |
| keepLINK | KP-9000-9XHML-X | Yes | 2M-PCB23-V3.2 | 2M | 8 + 1 |
| LIANGUO | SWTG024AS | No | SWTG024AS-v2.0-17452 | 0.5M | 4 + 2 |
| Lianguo | ZX-SWTGW215AS | Yes | PCB-SWTG115AS-V2.0 / PCB-SWTG115AS-V2.1 | 2M | 5 + 1 |
| Lianguo | HYWS-SGT0108S | No | 2G5F_20G_V1.01 | 0.5M | 8 + 1 |
| Mokerlink | 2G040210GSM | Yes | 2M-PCB43-V1.1 | 4 + 2 | |
| Mokerlink | ZX-SWTGW218AS | Yes | SWTG118AS-V2.0-16029 | 2M | 8 + 1 |
| MokerLink | POE-2G080110GS | No | 2M-PCB51-ML-V1.1 | 4M | 8 + 1 |
| Binardat | 2G06-04210GSM | No | PCB-SWTG024AS-A-2.0.1 | 0.5M | 4 + 2 |
| ONT | ONT-S207CW-62TS-SE | No | PCB-SWTG024AS-A-2.0.1 | 0.5M | 4 + 2 |
| Netcore | GS9 | No | PB-2132 | 4M | 8 + 1 |
| Ruiying | RY-4GT-2SX | No | FG-4GT-2SX_V2.0 | 4M | 4 + 2 |
| Ruiying | RY-8GT-1SX | No | FG-8GT-1SX | 1M | 8 + 1 |
| SiscoLink | SL-G0402F | No | PCB-K0402WS-V3.0 | 4 + 2 | |
| Sodola | SL-SWTG124AS-D | Yes | SWTG024AS-v2.0-17452 | 2M | 4 + 2 |
| Steamemo | IG204-V1 | No | PB-2131 | 4 + 2 | |
| TrendNet | TEG-S562 | No | TEG-S563/EU H/W: V1.0R | 2M | 4 + 2 |
| Xikestore | SKS3200M-4GPY2XF | Yes | SWTG024AS-v1.0 | 4 + 2 | |
| XikeStor | SKS3200-8E1X | Yes | SWTG118AS-V2.1-17462 | 2M | 8 + 1 |
| Ztyuav | Z-QWYT0402 | No | PCB-K0402WS-V3.0 | 4 + 2 | |
| Guangnianwei | 7018-2.5G | No | F7008-2.5GPOE-V1.2 | 8M | 8 + 1 |
For KP-9000-6XH-X2 / KP-9000-6XHML-X2 / Mokerlink 2G040210GSM devices, select the machine target by PCB revision. The ML/non-ML or managed/unmanaged label alone does not identify the wiring.
Other device based on RTL8272/3 that may work are described here: Up-N-Atoms 2.5 GBit RTL Switch hacking guide
Many of the RTL8272/3 devices come in versions with PoE support. The RTLPlayground usually also works on these, however, no support for configuring PoE is provided, simply because these devices usually just provide PoE on all ports without further configuration possibilitites.
The following forum also discusses this type of switches: ServeTheHome
There are also 16-port unmanaged devices with RTL8272 SoCs, however these devices do not have serial consoles and use 4 independent RTL8272 SoCs. No central control is provided by RTLPlayground, even if it has been successfully demonstrated to install RTLPlayground to individual SoCs.