Files
RTLPlayground/Makefile
T
bloqaudio 4050555667 port: add a cable test command
"port <port> cabletest" runs the cable diagnostic of the copper PHYs
and reports one line per pair: ok, or open, short, short to another
pair or impedance mismatch with the distance to the fault.

The PHY part follows the cable_test_start and cable_test_get_status
ops of the Linux phy_driver and takes the port number:
rtl_phy_cable_test_start() triggers the test and
rtl_phy_cable_test_get_status() returns true once all four pairs are
done, with a result code and a length per pair. The decode order is
the one of the Linux driver. The same two functions drive the RTL8224
and the internal PHYs of the RTL8372 and RTL8373.

The command only powers the port down and returns. A state machine
called from handle_tick() calls the start op after one second, polls
the status op, stores the result, clears the trigger, also after a
timeout, and restores the control register, so the main loop never
waits. The result is printed when it is ready and "port <port>
cabletest show" prints it again. One test runs at a time.

The result flags are the low byte of the per-pair status word. The
vendor code reads the high byte, which is always zero on the RTL8373.

A link partner that keeps transmitting makes the PHY report an
inter-pair short on every pair, and forcing the speed with
autonegotiation off, as the Linux driver does, does not take the link
down. The port is therefore powered down for a second before the
test. The control register is restored afterwards with an
autonegotiation restart, so speed settings survive and the link
returns.

A test started on a port that is switched off never finishes and
leaves the PHY unusable until the switch is reset, so such a port is
refused, and a test is dropped if the port is switched off during the
wait. SFP ports are refused by the existing check. The external copper
PHYs of the RTL8372 boards are refused because the test has not been
run on one.

The distance is the raw length word minus 150, at 43 counts per 50 cm.
Fitted on open cables of 0.9 m, 2 m and 7.6 m; the pairs of one cable
differ by about 0.2 m. The Linux formula, raw minus 620 at 78 counts
per metre, gives 0, 0 and 2.4 m for these cables.

An unplugged port has no defined result: some pairs report open at
about 0.5 m and others a short or a mismatch at 2 to 3 m.
2026-10-14 12:42:27 -05:00

224 lines
7.2 KiB
Makefile

VERSION=0.1.0
IMAGESIZE = 524288
DEFAULT_CONFIG_LOCATION = 454656
CONFIG_LOCATION = 458752
HTML_LOCATION = 262144
ifeq ($(origin CC),default)
CC = sdcc
endif
CC_FLAGS = -mmcs51 -I. -Imachine -Ihttpd -Iuip
ASM ?= sdas8051
AFLAGS= -plosgff
SUBDIRS := tools
SUBDIRSCLEAN=$(addsuffix clean,$(SUBDIRS))
# $MACHINE selects machine/$(MACHINE).c as the board definition and is passed
# on as -DMACHINE_$(MACHINE), which the rest of the firmware tests with
# #if defined(MACHINE_...), and as -DMACHINE_NAME, which machine.h uses to
# include machine/$(MACHINE).h. Both take the same value, so they cannot drift.
ifneq ($(MACHINE),)
CC_FLAGS += -DMACHINE_$(MACHINE)
CC_FLAGS += -DMACHINE_NAME=$(MACHINE)
endif
# Health instrumentation and the "health" console command: HEALTH=1 gmake ...
ifneq ($(HEALTH),)
CC_FLAGS += -DHEALTH
endif
ifeq ($(CI),1)
CC_FLAGS += --Werror
endif
# The board definition being built: one file per MACHINE_* symbol in machine.h.
MACHINE_SRC = machine/$(MACHINE).c
BUILDDIR = output/$(MACHINE)
VERSION_HEADER := version.h
GIT_VERSION := $(shell git rev-parse --short HEAD)
ifeq ($(shell git status --porcelain --untracked-files=no),)
else
GIT_VERSION := $(GIT_VERSION)-dirty
endif
VERSION_EXTENSION = v$(VERSION)-$(GIT_VERSION)
FILENAME_EXTENSION = $(VERSION_EXTENSION)-$(MACHINE)
# Deterministic build date: honor SOURCE_DATE_EPOCH, else the HEAD commit date,
# else wall-clock (no-git fallback). Keeps same-commit builds byte-identical
# (BUILD_DATE is baked into the image and covered by the trailing CRC).
SOURCE_DATE_EPOCH ?= $(shell git show -s --format=%ct HEAD 2>/dev/null)
ifeq ($(SOURCE_DATE_EPOCH),)
BUILD_DATE := $(shell date +"%Y-%m-%d %H:%M:%S")
else
BUILD_DATE := $(shell date -u -d @$(SOURCE_DATE_EPOCH) +"%Y-%m-%d %H:%M:%S" 2>/dev/null \
|| date -u -r $(SOURCE_DATE_EPOCH) +"%Y-%m-%d %H:%M:%S")
endif
# $(MACHINE_SRC) is listed here so an unknown $MACHINE fails before anything else
# is built, including the tools/ subdirectory.
all: create_build_dir $(VERSION_HEADER) $(MACHINE_SRC) $(SUBDIRS) $(BUILDDIR)/rtlplayground-$(FILENAME_EXTENSION).bin
create_build_dir:
mkdir -p "$(BUILDDIR)"
mkdir -p "$(BUILDDIR)/uip"
mkdir -p "$(BUILDDIR)/httpd"
mkdir -p "$(BUILDDIR)/machine"
# Every machine is a pair machine/<MACHINE>.c + machine/<MACHINE>.h. Selecting
# them by name means no #if/#elif chain, so an unknown or empty $MACHINE is
# caught here instead of by a #error further down the build.
$(MACHINE_SRC):
@echo "ERROR: MACHINE='$(MACHINE)' has no definition (expected $(MACHINE_SRC))." >&2
@echo " Every machine is one file pair under machine/, named after the" >&2
@echo " MACHINE_* symbol it defines; see machine/*.c for the full list." >&2
@echo " Example: make MACHINE=KP_9000_6XHML_X2" >&2
@false
# Keep the per-machine definition in first position to fail immediately on an
# invalid $MACHINE value
SRCS = \
$(MACHINE_SRC) \
machine_init.c \
cmd_editor.c \
cmd_parser.c \
dhcp.c \
html_data.c \
rtlplayground.c \
boot.c \
sfp.c \
dns.c \
dns_cli.c \
ntp.c \
ntp_cli.c \
syslog.c \
udp_apps.c
# RTL837x
SRCS += \
rtl837x_bandwidth.c \
rtl837x_cabletest.c \
rtl837x_flash.c \
rtl837x_igmp.c \
rtl837x_init.c \
rtl837x_leds.c \
rtl837x_leds_dump.c \
rtl837x_phy.c \
rtl837x_pins.c\
rtl837x_port.c \
rtl837x_stp.c \
rtl837x_lldp.c \
rtl837x_storm.c \
rtl837x_lacp.c \
rtl837x_trap.c
SRCS += \
httpd/httpd.c \
httpd/page_impl.c
SRCS += \
uip/timer.c \
uip/uip.c \
uip/uiplib.c \
uip/uip_arp.c \
uip/uip-fw.c \
uip/uip-neighbor.c \
uip/uip-split.c
OBJS = ${SRCS:%.c=$(BUILDDIR)/%.rel}
DEPS := ${SRCS:%.c=$(BUILDDIR)/%.d}
HTML := $(shell find html -name '*.js' -or -name '*.html' -or -name '*.svg' -or -name '*.css' -or -name '*.ico')
# Minified copy of the web UI sources, used as the fileadder input.
# The raw html/ sources stay untouched for development; the minified
# copy is a build artifact under output/.
HTML_MIN := output/html_min
.PHONY: html_min
html_min: $(HTML)
rm -rf $(HTML_MIN)
mkdir -p $(HTML_MIN)
@for f in $(HTML); do python3 tools/minify.py $$f $(HTML_MIN)/$$(basename $$f) || exit 1; done
html_data.c html_data.h &: $(HTML) | tools html_min
tools/output/fileadder -a $(HTML_LOCATION) -s $(IMAGESIZE) -b BANK1 -z -d $(HTML_MIN) -p html_data
$(VERSION_HEADER): FORCE
@printf '%s\n' "#ifndef VERSION_H" "#define VERSION_H" \
"#define VERSION_SW \"$(VERSION_EXTENSION)\"" \
"#define BUILD_DATE \"$(BUILD_DATE)\"" \
"#endif" > $(VERSION_HEADER).tmp
@cmp -s $(VERSION_HEADER).tmp $(VERSION_HEADER) \
&& rm -f $(VERSION_HEADER).tmp \
|| mv $(VERSION_HEADER).tmp $(VERSION_HEADER)
httpd: html_data.h
$(SUBDIRS):
$(MAKE) -C $@
clean: $(SUBDIRSCLEAN)
-rm -f html_data.c html_data.h $(VERSION_HEADER)
-if [ -d $(BUILDDIR) ]; then find $(BUILDDIR) -type f ! -name "*.bin" -delete; fi
distclean: $(SUBDIRSCLEAN)
-rm -f html_data.c html_data.h $(VERSION_HEADER)
-rm -rf $(BUILDDIR)
$(SUBDIRSCLEAN):
$(MAKE) -C $(@:clean=) clean
# Objects depend on the flags they were built with, through a stamp file that
# is rewritten only when CC_FLAGS actually changes.
CCFLAGS_STAMP := $(BUILDDIR)/.ccflags
.PHONY: FORCE
FORCE:
$(CCFLAGS_STAMP): FORCE | create_build_dir
@echo '$(CC_FLAGS)' | cmp -s - $@ 2>/dev/null || echo '$(CC_FLAGS)' > $@
$(BUILDDIR)/%.rel: %.c $(CCFLAGS_STAMP) | create_build_dir html_data.h
$(CC) -MMD $(CC_FLAGS) -o $@ -c $<
$(BUILDDIR)/%.rel: %.asm $(CCFLAGS_STAMP) | create_build_dir
${ASM} ${AFLAGS} -o $@ $<
# mv -f $(addprefix $(basename $^), .lst .rel .sym) .
$(BUILDDIR)/rtlplayground.ihx: $(OBJS) $(BUILDDIR)/crtbank.rel $(BUILDDIR)/crc16.rel
$(CC) $(CC_FLAGS) --xram-size 49151 -Wl-bHOME=0x00000 -Wl-bBANK1=0x14000 -Wl-bBANK2=0x24000 -Wl-bBANK3=0x34000 -Wl-r -o $@ $^
$(BUILDDIR)/rtlplayground.img: $(BUILDDIR)/rtlplayground.ihx
objcopy --input-target=ihex -O binary $< $@
$(BUILDDIR)/rtlplayground-$(FILENAME_EXTENSION).bin: $(BUILDDIR)/rtlplayground.img | tools
if [ -e $@ ]; then rm $@; fi
tools/output/imagebuilder -i $^ $@
tools/output/fileadder -a $(DEFAULT_CONFIG_LOCATION) -s $(IMAGESIZE) -d config.txt $@
tools/output/fileadder -a $(CONFIG_LOCATION) -s $(IMAGESIZE) -d config.txt $@
tools/output/fileadder -a $(HTML_LOCATION) -s $(IMAGESIZE) -z -d $(HTML_MIN) -b BANK1 $@
tools/output/crc_calculator -u $@
ln -sf $(MACHINE)/rtlplayground-$(FILENAME_EXTENSION).bin output/rtlplayground.bin
.PHONY: clean distclean all $(SUBDIRS) $(SUBDIRSCLEAN) create_build_dir
# Every machine/ definition is compiled, so a machine added to machine/ is
# covered without registering it anywhere. The machine-specific defines are
# filtered out of $(CC_FLAGS) and supplied per iteration instead, so this also
# works as "make machine_check MACHINE=...".
MACHINE_DEFS := $(sort $(patsubst machine/%.c,%,$(wildcard machine/*.c)))
MACHINE_LESS_CC_FLAGS = $(filter-out -DMACHINE_%,$(CC_FLAGS))
.PHONY:
machine_check:
@mkdir -p $(BUILDDIR)/tmp
@set -eo pipefail; \
for MACHINE in $(MACHINE_DEFS); \
do \
echo "Checking $${MACHINE}"; \
$(CC) $(MACHINE_LESS_CC_FLAGS) -DMACHINE_$${MACHINE} -DMACHINE_NAME=$${MACHINE} -MMD -o $(BUILDDIR)/tmp/machine_check -c machine/$${MACHINE}.c; \
$(CC) $(MACHINE_LESS_CC_FLAGS) -DMACHINE_$${MACHINE} -DMACHINE_NAME=$${MACHINE} -MMD -o $(BUILDDIR)/tmp/machine_check -c machine_init.c; \
done
@rm -rf $(BUILDDIR)/tmp
-include $(DEPS)