mirror of
https://github.com/logicog/RTLPlayground.git
synced 2026-10-29 17:54:14 +08:00
Brunoz78andClaude Opus 5.5
b71239f394
The V3.2 board has the same component placement as V3.1 and works with its machine definition: RJ45 links at 2.5G, LEDs, SFP detection with DOM readings at 10G, factory MAC at 0x1FC000 and the reset button. The new target only reports "V3.2" as the machine name. Installed from the original firmware V100.9.25 through its web interface with the OEM installer image. Reading the flash in-circuit with a SOIC-8 clip gave the chip ID EF FF FF, as on a V3.1 board. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
1408 lines
46 KiB
C
1408 lines
46 KiB
C
#include "machine.h"
|
|
#include "rtl837x_pins.h"
|
|
#include "rtl837x_leds.h"
|
|
#include "rtl837x_sfr.h"
|
|
#include "rtl837x_regs.h"
|
|
#include "rtl837x_common.h"
|
|
|
|
#define I2CBUS_INVALID (7)
|
|
// This is a MACRO to check if I2C_BUS_FROM_SDA_PIN or I2C_BUS_FROM_SCL_PIN don't return I2CBUS_INVALID.
|
|
// When I2CBUS_INVALID is returned, compiler stops with "machine.c:<line>: error 176: sizeof applied to an incomplete type"
|
|
#define I2CBUS_VALID(bus) (0 * sizeof(char[(bus) != I2CBUS_INVALID ? 1 : 0]))
|
|
#define I2CBUS(sda, scl) \
|
|
((uint8_t)((I2C_BUS_FROM_SCL_PIN(scl) << RTL837X_REG_I2C_SCL_SHIFT) | \
|
|
(I2C_BUS_FROM_SDA_PIN(sda) << RTL837X_REG_I2C_SDA_SHIFT) | \
|
|
I2CBUS_VALID(I2C_BUS_FROM_SCL_PIN(scl)) | \
|
|
I2CBUS_VALID(I2C_BUS_FROM_SDA_PIN(sda))))
|
|
|
|
#define I2C_BUS_FROM_SDA_PIN(sda_pin) \
|
|
((sda_pin) == GPIO47_I2C_SDA0 ? 0 : \
|
|
(sda_pin) == GPIO49_I2C_SDA1 ? 1 : \
|
|
(sda_pin) == GPIO51_I2C_SDA2_UART1_RX ? 2 : \
|
|
(sda_pin) == GPIO41_I2C_SDA3_MDIO1 ? 3 : \
|
|
(sda_pin) == GPIO39_I2C_SDA4 ? 4 : I2CBUS_INVALID)
|
|
|
|
#define I2C_BUS_FROM_SCL_PIN(scl_pin) \
|
|
((scl_pin) == GPIO46_I2C_SCL0 ? 0 : \
|
|
(scl_pin) == GPIO48_I2C_SCL1 ? 1 : \
|
|
(scl_pin) == GPIO50_I2C_SCL2_UART1_TX ? 2 : \
|
|
(scl_pin) == GPIO40_I2C_SCL3_MDC1 ? 3 : I2CBUS_INVALID)
|
|
|
|
#if defined(MACHINE_KP_9000_6XHML_X2) || \
|
|
defined(MACHINE_KP_9000_6XH_X2_V1_1) || \
|
|
defined(MACHINE_KP_9000_6XHML_X2_V1_1) || \
|
|
defined(MACHINE_KP_9000_6XH_X2_V1_2) || \
|
|
defined(MACHINE_KP_9000_6XHML_X2_V1_2)
|
|
__code const struct machine machine = {
|
|
#if defined(MACHINE_KP_9000_6XH_X2_V1_1)
|
|
.machine_name = "keepLink KP-9000-6XH V1.1",
|
|
#elif defined(MACHINE_KP_9000_6XHML_X2_V1_1)
|
|
.machine_name = "keepLink KP-9000-6XHML V1.1",
|
|
#elif defined(MACHINE_KP_9000_6XH_X2_V1_2)
|
|
.machine_name = "keepLink KP-9000-6XH V1.2",
|
|
#elif defined(MACHINE_KP_9000_6XHML_X2_V1_2)
|
|
.machine_name = "keepLink KP-9000-6XHML V1.2",
|
|
#else
|
|
.machine_name = "keepLink KP-9000-6XHML-X2",
|
|
#endif
|
|
.isRTL8373 = 0,
|
|
.min_port = 3,
|
|
.max_port = 8,
|
|
.n_sfp = 2,
|
|
.log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
|
|
.phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
|
|
.is_sfp = {0, 0, 0, 1, 0, 0, 0, 0, 2},
|
|
// Left SFP port (5)
|
|
.sfp_port[0].pin_detect = GPIO50_I2C_SCL2_UART1_TX,
|
|
.sfp_port[0].pin_los = GPIO10_LED10,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 0,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO41_I2C_SDA3_MDIO1, GPIO40_I2C_SCL3_MDC1 ),
|
|
// Right SFP port (6)
|
|
.sfp_port[1].pin_detect = GPIO30_ACL_BIT3_EN,
|
|
.sfp_port[1].pin_los = GPIO37,
|
|
.sfp_port[1].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[1].sds = 1,
|
|
.sfp_port[1].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
.reset_pin = GPIO54_ACL_BIT2_EN,
|
|
.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28_SYS | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 0},
|
|
/* Conditions for LED on:
|
|
* dual led orange: ledset_0 & ledset_2
|
|
* dual led green: ledset_2 & !ledset_0
|
|
* single right led green: ledset_0 & !ledset_1
|
|
*/
|
|
.led_sets = { { LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
|
|
LEDS_2G5 | LEDS_LINK | LEDS_10G,
|
|
LEDS_1G | LEDS_LINK,
|
|
0 },
|
|
},
|
|
};
|
|
|
|
#elif defined MACHINE_KP_9000_6XH_X
|
|
__code const struct machine machine = {
|
|
.machine_name = "keepLink KP-9000-6XH-X",
|
|
.isRTL8373 = 0,
|
|
.min_port = 3,
|
|
.max_port = 8,
|
|
.n_sfp = 1,
|
|
.log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
|
|
.phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
|
|
.sfp_port[0].pin_los = GPIO37,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
.reset_pin = GPIO_NA,
|
|
/* Conditions for LED on:
|
|
* dual led orange: ledset_0 & ledset_2
|
|
* dual led green: ledset_2 & !ledset_0
|
|
* single right led green: ledset_0 & !ledset_1
|
|
*/
|
|
.led_sets = { { LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
|
|
LEDS_2G5 | LEDS_LINK | LEDS_10G,
|
|
LEDS_1G | LEDS_LINK,
|
|
0 },
|
|
},
|
|
};
|
|
|
|
#elif defined(MACHINE_KP_9000_6XH_X2) || defined(MACHINE_KP_9000_6XH_X2_V2_1) || defined(MACHINE_KP_9000_6XHML_X2_V2_1)
|
|
__code const struct machine machine = {
|
|
#if defined(MACHINE_KP_9000_6XHML_X2_V2_1)
|
|
.machine_name = "keepLink KP-9000-6XHML V2.1",
|
|
#elif defined(MACHINE_KP_9000_6XH_X2_V2_1)
|
|
.machine_name = "keepLink KP-9000-6XH-X2 V2.1",
|
|
#else
|
|
.machine_name = "keepLink KP-9000-6XH-X2",
|
|
#endif
|
|
.isRTL8373 = 0,
|
|
.min_port = 3,
|
|
.max_port = 8,
|
|
.n_sfp = 2,
|
|
.log_to_phys_port = {0, 0, 0, 6, 1, 2, 3, 4, 5},
|
|
.phys_to_log_port = {4, 5, 6, 7, 8, 3, 0, 0, 0},
|
|
.is_sfp = {0, 0, 0, 2, 0, 0, 0, 0, 1},
|
|
|
|
// Left SFP port
|
|
.sfp_port[0].pin_detect = GPIO38,
|
|
.sfp_port[0].pin_los = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
|
|
// Right SFP port
|
|
.sfp_port[1].pin_detect = GPIO37,
|
|
.sfp_port[1].pin_los = GPIO_NA,
|
|
.sfp_port[1].sds = 0,
|
|
.sfp_port[1].i2c = I2CBUS( GPIO41_I2C_SDA3_MDIO1, GPIO40_I2C_SCL3_MDC1 ),
|
|
|
|
.reset_pin = GPIO48_I2C_SCL1, // Button-Switch is unpopulated on PCB, but can be added manually (hole in case is already there)
|
|
.high_leds = { .mux = LED_28_SYS | LED_29, .enable = LED_27 | LED_28_SYS | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 1, 0, 0, 0, 0, 1},
|
|
.led_sets = {
|
|
{
|
|
LEDS_2G5 | LEDS_LINK, // Left LED (Amber)
|
|
LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT, // Right LED (Green)
|
|
0,
|
|
0
|
|
},
|
|
{
|
|
LEDS_10G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
0,
|
|
0,
|
|
0
|
|
},
|
|
},
|
|
.led_mux_custom = 1,
|
|
.led_mux = {
|
|
0x00,0x01,0x04,0x05,0x08,0x09,0x0c,0x3f,0x0d,0x10,
|
|
0x11,0x0e,0x14,0x11,0x12,0x15,0x15,0x16,0x18,0x19,
|
|
0x1a,0x19,0x1d,0x1e,0x1c,0x1d,0x20,0x21
|
|
},
|
|
};
|
|
|
|
#elif defined MACHINE_KP_9000_9XH_X_EU
|
|
__code const struct machine machine = {
|
|
.machine_name = "keepLink KP-9000-9XH-X-EU",
|
|
.isRTL8373 = 1,
|
|
.min_port = 0,
|
|
.max_port = 8,
|
|
.n_sfp = 1,
|
|
.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
|
|
.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
|
|
.sfp_port[0].pin_los = GPIO37,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
.reset_pin = GPIO_NA,
|
|
.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28_SYS | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 0},
|
|
.led_sets = { { LEDS_2G5 | LEDS_TWO_PAIR_1G | LEDS_1G | LEDS_500M | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G | LEDS_TWO_PAIR_5G | LEDS_5G | LEDS_TWO_PAIR_2G5,
|
|
LEDS_2G5 | LEDS_LINK,
|
|
LEDS_1G | LEDS_LINK,
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT },
|
|
},
|
|
};
|
|
|
|
#elif defined MACHINE_KP_9000_9XHML_X_V2_2
|
|
__code const struct machine machine = {
|
|
.machine_name = "keepLink KP-9000-9XHML-X V2.2",
|
|
.isRTL8373 = 1,
|
|
.min_port = 0,
|
|
.max_port = 8,
|
|
.n_sfp = 1,
|
|
.log_to_phys_port = { 1, 2, 3, 4, 5, 6, 7, 8, 9 },
|
|
.phys_to_log_port = { 0, 1, 2, 3, 4, 5, 6, 7, 8 },
|
|
.is_sfp = { 0, 0, 0, 0, 0, 0, 0, 0, 1 },
|
|
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
|
|
.sfp_port[0].pin_los = GPIO37,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
.reset_pin = GPIO54_ACL_BIT2_EN,
|
|
.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28_SYS | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1 },
|
|
.led_sets = {
|
|
{ /* Set 0 for RJ45 connectors */
|
|
/* LED0: Right Green */
|
|
LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
/* LED1: Left Orange */
|
|
LEDS_2G5 | LEDS_LINK,
|
|
/* LED2: Left Green */
|
|
LEDS_1G | LEDS_LINK,
|
|
/* LED3: None */
|
|
0,
|
|
}, { /* Set 1 for SFP port */
|
|
/* LED0: Single Green "9" LED */
|
|
LEDS_2G5 | LEDS_TWO_PAIR_1G | LEDS_1G | LEDS_500M | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G | LEDS_TWO_PAIR_5G | LEDS_5G | LEDS_TWO_PAIR_2G5,
|
|
/* LED1: D23 LED on PCB */
|
|
LEDS_1G | LEDS_LINK,
|
|
/* LED2: D22 LED on PCB */
|
|
LEDS_2G5 | LEDS_LINK,
|
|
/* LED3: Unused */
|
|
LEDS_COL | LEDS_DUPLEX,
|
|
}, { /* Set 2: Unused, but set to same things as stock firmware for consistency */
|
|
LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
LEDS_1G | LEDS_LINK | LEDS_ACT,
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT | LEDS_5G,
|
|
LEDS_10G | LEDS_ACT | LEDS_LINK,
|
|
}, { /* Set 3: Unused, but set to same things as stock firmware for consistency */
|
|
LEDS_TX,
|
|
LEDS_RX,
|
|
LEDS_2G5 | LEDS_TWO_PAIR_1G | LEDS_1G | LEDS_500M | LEDS_100M | LEDS_10M | LEDS_ACT | LEDS_10G | LEDS_TWO_PAIR_5G | LEDS_5G | LEDS_TWO_PAIR_2G5,
|
|
LEDS_2G5 | LEDS_TWO_PAIR_1G | LEDS_1G | LEDS_500M | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_10G | LEDS_TWO_PAIR_5G | LEDS_5G | LEDS_TWO_PAIR_2G5,
|
|
},
|
|
},
|
|
};
|
|
|
|
#elif defined(MACHINE_KP_9000_9XHML_X_V3_1) || defined(MACHINE_KP_9000_9XHML_X_V3_2)
|
|
// 2M-PCB23-V3.2 is wired like V3.1 (SFP detection, LEDs, factory MAC location)
|
|
__code const struct machine machine = {
|
|
#if defined(MACHINE_KP_9000_9XHML_X_V3_2)
|
|
.machine_name = "keepLink KP-9000-9XHML-X V3.2",
|
|
#else
|
|
.machine_name = "keepLink KP-9000-9XHML-X V3.1",
|
|
#endif
|
|
.isRTL8373 = 1,
|
|
.min_port = 0,
|
|
.max_port = 8,
|
|
.n_sfp = 1,
|
|
.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
|
|
.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.sfp_port[0].pin_detect = GPIO38,
|
|
.sfp_port[0].pin_los = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
.reset_pin = GPIO48_I2C_SCL1,
|
|
.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28_SYS | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.led_sets = {
|
|
{ /* RJ45: First LED, yellow, second LED: green */
|
|
LEDS_2G5 | LEDS_LINK,
|
|
LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
0,
|
|
0,
|
|
}, { /* SFP PORT, SINGLE GREEN LED */
|
|
LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
|
|
0,
|
|
0,
|
|
0,
|
|
}},
|
|
.led_mux_custom = 1,
|
|
.led_mux = {0x00, 0x01, 0x04, 0x05, 0x08, 0x09, 0x0c, 0x09, 0x0d, 0x10,
|
|
0x11, 0x0e, 0x14, 0x11, 0x12, 0x15, 0x15, 0x16, 0x18, 0x19,
|
|
0x1a, 0x19, 0x1d, 0x1e, 0x1c, 0x1d, 0x20, 0x21},
|
|
.mac_flash_offset = 0x1FC000,
|
|
};
|
|
|
|
#elif defined MACHINE_SWGT024_V2_0_MANAGED
|
|
__code const struct machine machine = {
|
|
.machine_name = "SWGT024 V2.0 Managed",
|
|
.isRTL8373 = 0,
|
|
.min_port = 3,
|
|
.max_port = 8,
|
|
.n_sfp = 2,
|
|
.log_to_phys_port = {0, 0, 0, 6, 1, 2, 3, 4, 5},
|
|
.phys_to_log_port = {4, 5, 6, 7, 8, 3, 0, 0, 0},
|
|
.is_sfp= {0, 0, 0, 2, 0, 0, 0, 0, 1},
|
|
// Left SFP port (J4)
|
|
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
|
|
.sfp_port[0].pin_los = GPIO_NA,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ), /* GPIO 39 */
|
|
// Right SFP port (J2)
|
|
.sfp_port[1].pin_detect = GPIO50_I2C_SCL2_UART1_TX,
|
|
.sfp_port[1].pin_los = GPIO_NA,
|
|
.sfp_port[1].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[1].sds = 0,
|
|
.sfp_port[1].i2c = I2CBUS( GPIO41_I2C_SDA3_MDIO1, GPIO40_I2C_SCL3_MDC1 ), /* GPIO 40 */
|
|
.reset_pin = GPIO54_ACL_BIT2_EN,
|
|
.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28_SYS | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 1, 0, 0, 0, 0, 1},
|
|
.led_sets = {
|
|
{ /* RJ45: Green LED */
|
|
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
|
|
0,
|
|
/* Amber LED */
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT,
|
|
0
|
|
}, { /* SFP PORT: SINGLE GREEN LED */
|
|
LEDS_10M | LEDS_100M | LEDS_1G | LEDS_2G5 | LEDS_10G | LEDS_LINK | LEDS_ACT,
|
|
0,
|
|
0,
|
|
0,
|
|
},
|
|
},
|
|
};
|
|
|
|
#elif defined MACHINE_SWGT024_V2_0_UNMANAGED
|
|
__code const struct machine machine = {
|
|
.machine_name = "SWGT024 V2.0 Unmanaged",
|
|
.isRTL8373 = 0,
|
|
.min_port = 3,
|
|
.max_port = 8,
|
|
.n_sfp = 2,
|
|
.log_to_phys_port = {0, 0, 0, 6, 1, 2, 3, 4, 5},
|
|
.phys_to_log_port = {4, 5, 6, 7, 8, 3, 0, 0, 0},
|
|
.is_sfp= {0, 0, 0, 2, 0, 0, 0, 0, 1},
|
|
// Left SFP port (J4)
|
|
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
|
|
.sfp_port[0].pin_los = GPIO37,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ), /* GPIO 39 */
|
|
// Right SFP port (J2)
|
|
.sfp_port[1].pin_detect = GPIO50_I2C_SCL2_UART1_TX,
|
|
.sfp_port[1].pin_los = GPIO51_I2C_SDA2_UART1_RX,
|
|
.sfp_port[1].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[1].sds = 0,
|
|
.sfp_port[1].i2c = I2CBUS( GPIO41_I2C_SDA3_MDIO1, GPIO40_I2C_SCL3_MDC1 ), /* GPIO 40 */
|
|
.reset_pin = GPIO_NA,
|
|
.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28_SYS | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 1, 0, 0, 0, 0, 1},
|
|
.led_sets = {
|
|
{ /* RJ45: Green LED */
|
|
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
|
|
0,
|
|
/* Amber LED */
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT,
|
|
0
|
|
}, { /* SFP PORT: SINGLE GREEN LED */
|
|
LEDS_10M | LEDS_100M | LEDS_1G | LEDS_2G5 | LEDS_10G | LEDS_LINK | LEDS_ACT,
|
|
0,
|
|
0,
|
|
0,
|
|
},
|
|
},
|
|
};
|
|
|
|
#elif defined MACHINE_SWTG018AS_A_V_2_0
|
|
__code const struct machine machine = {
|
|
.machine_name = "SWTG018AS-A V2.0",
|
|
.isRTL8373 = 1,
|
|
.min_port = 0,
|
|
.max_port = 8,
|
|
.n_sfp = 1,
|
|
.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
|
|
.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.sfp_port[0].pin_detect = GPIO38,
|
|
.sfp_port[0].pin_los = GPIO_NA,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
.reset_pin = GPIO48_I2C_SCL1,
|
|
.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28_SYS | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.led_sets = {
|
|
{ /* RJ45: First LED, yellow, second LED: green */
|
|
LEDS_2G5 | LEDS_LINK,
|
|
LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
0,
|
|
0,
|
|
}, { /* SFP PORT, SINGLE GREEN LED */
|
|
LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
|
|
0,
|
|
0,
|
|
0,
|
|
}},
|
|
.led_mux_custom = 1,
|
|
.led_mux = { 0x00, 0x01, 0x04, 0x05, 0x08, // 65e0
|
|
0x09, 0x0c, 0x09, 0x0d, 0x10, // 65e4
|
|
0x11, 0x0e, 0x14, 0x11, 0x12, // 65e8
|
|
0x15, 0x15, 0x16, 0x18, 0x19, // 65ec
|
|
0x1a, 0x19, 0x1d, 0x1e, 0x1c, // 65f0
|
|
0x1d, 0x20, 0x21 },
|
|
};
|
|
|
|
#elif defined MACHINE_HG0402XG_V1_1
|
|
__code const struct machine machine = {
|
|
.machine_name = "HG0402XG V1.1",
|
|
.isRTL8373 = 0,
|
|
.min_port = 3,
|
|
.max_port = 8,
|
|
.n_sfp = 2,
|
|
.log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
|
|
.phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
|
|
.is_sfp = {0, 0, 0, 2, 0, 0, 0, 0, 1},
|
|
.sfp_port[0].pin_detect = 50,
|
|
.sfp_port[0].pin_los = 10,
|
|
.sfp_port[0].pin_tx_disable = 0xFF,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO41_I2C_SDA3_MDIO1, GPIO40_I2C_SCL3_MDC1 ),
|
|
.sfp_port[1].pin_detect = 30,
|
|
.sfp_port[1].pin_los = 51,
|
|
.sfp_port[1].pin_tx_disable = 0xFF,
|
|
.sfp_port[1].sds = 0,
|
|
.sfp_port[1].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
.reset_pin = GPIO_NA,
|
|
.high_leds = { .mux = LED_27 , .enable = LED_27 | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 1, 0, 0, 0, 0, 1},
|
|
/* The Ethernet ports have 1 amber LED (left) and 1 green LED (right)
|
|
* The SFP ports have also 1 amber LED and 1 green LED
|
|
* Ethernet ports use LED-set 0, SFP ports use LED-set 1
|
|
*/
|
|
.led_sets = { { LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_2G5 | LEDS_LINK | LEDS_ACT,
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT,
|
|
0 },
|
|
{ LEDS_100M | LEDS_10M | LEDS_LINK,
|
|
LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
|
|
LEDS_10G | LEDS_LINK,
|
|
0 },
|
|
},
|
|
};
|
|
|
|
#elif defined MACHINE_SWTGW218AS
|
|
|
|
__code const struct machine machine = {
|
|
.machine_name = "SWTGW218AS 8+1 Managed Switch",
|
|
.isRTL8373 = 1,
|
|
.mac_flash_offset = 0x1FC000,
|
|
.min_port = 0,
|
|
.max_port = 8,
|
|
.n_sfp = 1,
|
|
.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
|
|
.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
|
|
.sfp_port[0].pin_los = GPIO37,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
.reset_pin = GPIO54_ACL_BIT2_EN,
|
|
.high_leds = { .mux = LED_27 | LED_28_SYS | LED_29, .enable = LED_28_SYS | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.led_sets = { { LEDS_2G5 | LEDS_LINK | LEDS_ACT, // Green LED (right)
|
|
0, // unused
|
|
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT, // Amber LED (left)
|
|
0
|
|
}, // unused
|
|
{ LEDS_10G | LEDS_5G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_LINK | LEDS_ACT, // SFP LED
|
|
0, // unused
|
|
0, // unused
|
|
0
|
|
}, // unused },
|
|
},
|
|
};
|
|
|
|
#elif defined MACHINE_PCB_SWTG018AS_V2_1_0 // Sold as Sodola SL902 / Horaco "SWTGW218AS"; the SWTGW218AS label also covers other PCBs with different SFP and LED wiring (see MACHINE_SWTGW218AS)
|
|
|
|
__code const struct machine machine = {
|
|
.machine_name = "SWTGW218AS (SWTG018AS-V2.1.0)",
|
|
.isRTL8373 = 1,
|
|
.mac_flash_offset = 0x1FC000,
|
|
.min_port = 0,
|
|
.max_port = 8,
|
|
.n_sfp = 1,
|
|
.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
|
|
.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.sfp_port[0].pin_detect = GPIO38, // pulled low on module insert
|
|
.sfp_port[0].pin_los = GPIO_NA, // no LOS pin wired
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
.reset_pin = GPIO54_ACL_BIT2_EN,
|
|
.high_leds = { .mux = LED_27 | LED_28_SYS | LED_29, .enable = LED_28_SYS | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
// LED wiring matches the SWTG018AS-A V2.0 (same PCB family)
|
|
.led_sets = {
|
|
{ /* RJ45: First LED, yellow, second LED: green */
|
|
LEDS_2G5 | LEDS_LINK,
|
|
LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
0,
|
|
0,
|
|
}, { /* SFP set (superseded by the raw register override in machine_custom_init) */
|
|
LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
|
|
0,
|
|
0,
|
|
0,
|
|
}},
|
|
.led_mux_custom = 1,
|
|
.led_mux = { 0x00, 0x01, 0x04, 0x05, 0x08, // 65e0
|
|
0x09, 0x0c, 0x09, 0x0d, 0x10, // 65e4
|
|
0x11, 0x0e, 0x14, 0x11, 0x12, // 65e8
|
|
0x15, 0x15, 0x16, 0x18, 0x19, // 65ec
|
|
0x1a, 0x19, 0x1d, 0x1e, 0x1c, // 65f0
|
|
0x1d, 0x20, 0x21 },
|
|
};
|
|
|
|
#elif defined MACHINE_LIANGUO_ZX_SWTGW215AS // Has PCB branded PCB-SWTG115AS-V2.0 but is labeled and reports as a ZX-SWTGW215AS, seems to be identical to the "real" ZX-SWTGW215AS except for the LEDs
|
|
__code const struct machine machine = {
|
|
.machine_name = "Lianguo ZX-SWTGW215AS",
|
|
.isRTL8373 = 0,
|
|
.mac_flash_offset = 0x1FC000,
|
|
.min_port = 3,
|
|
.max_port = 8,
|
|
.n_sfp = 1,
|
|
.log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
|
|
.phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
|
|
.sfp_port[0].pin_los = GPIO37,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
.reset_pin = GPIO54_ACL_BIT2_EN,
|
|
.high_leds = { .mux = LED_27 | LED_28_SYS | LED_29, .enable = LED_28_SYS | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.led_sets = { { LEDS_2G5 | LEDS_LINK | LEDS_ACT, // Green LED (right)
|
|
0, // unused
|
|
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT, // Amber LED (left)
|
|
0
|
|
}, // unused
|
|
{ LEDS_10G | LEDS_5G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_LINK | LEDS_ACT, // SFP LED
|
|
0, // unused
|
|
0, // unused
|
|
0
|
|
}, // unused },
|
|
},
|
|
.led_mux_custom = 0,
|
|
};
|
|
|
|
#elif defined MACHINE_DEFAULT_8C_1SFP
|
|
__code const struct machine machine = {
|
|
.machine_name = "8+1 SFP Port Switch",
|
|
.isRTL8373 = 1,
|
|
.min_port = 0,
|
|
.max_port = 8,
|
|
.n_sfp = 1,
|
|
.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
|
|
.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
|
|
.sfp_port[0].pin_los = GPIO37,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
.reset_pin = GPIO_NA,
|
|
.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28_SYS | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 0},
|
|
.led_sets = { { LEDS_2G5 | LEDS_TWO_PAIR_1G | LEDS_1G | LEDS_500M | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G | LEDS_TWO_PAIR_5G | LEDS_5G | LEDS_TWO_PAIR_2G5,
|
|
LEDS_2G5 | LEDS_LINK,
|
|
LEDS_1G | LEDS_LINK,
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT },
|
|
},
|
|
};
|
|
|
|
#elif defined MACHINE_TRENDNET_TEG_S562
|
|
__code const struct machine machine = {
|
|
.machine_name = "Trendnet TEG-S562",
|
|
.isRTL8373 = 0,
|
|
.min_port = 3,
|
|
.max_port = 8,
|
|
.n_sfp = 2,
|
|
.log_to_phys_port = {0, 0, 0, 6, 1, 2, 3, 4, 5},
|
|
.phys_to_log_port = {4, 5, 6, 7, 8, 3, 0, 0, 0},
|
|
.is_sfp = {0, 0, 0, 1, 0, 0, 0, 0, 2},
|
|
.sfp_port[0].pin_detect = GPIO38,
|
|
.sfp_port[0].pin_los = GPIO50_I2C_SCL2_UART1_TX,
|
|
.sfp_port[0].pin_tx_disable = GPIO54_ACL_BIT2_EN,
|
|
.sfp_port[0].sds = 0,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO47_I2C_SDA0, GPIO46_I2C_SCL0 ),
|
|
.sfp_port[1].pin_detect = GPIO36_PWM_OUT,
|
|
.sfp_port[1].pin_los = GPIO37,
|
|
.sfp_port[1].pin_tx_disable = GPIO51_I2C_SDA2_UART1_RX,
|
|
.sfp_port[1].sds = 1,
|
|
.sfp_port[1].i2c = I2CBUS( GPIO49_I2C_SDA1, GPIO48_I2C_SCL1 ),
|
|
.reset_pin = GPIO_NA,
|
|
.port_led_set = { 0, 0, 0, 1, 0, 0, 0, 0, 1},
|
|
.led_sets = {
|
|
{
|
|
0, // Unused
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT, // Green
|
|
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT, // Amber
|
|
0 // Unused
|
|
},
|
|
{
|
|
0, // Unused
|
|
0, // Unused
|
|
LEDS_10G | LEDS_1G | LEDS_LINK | LEDS_ACT, // Green
|
|
0, // Unused
|
|
},
|
|
},
|
|
|
|
};
|
|
|
|
#elif defined(MACHINE_PCB_K0402WS_V3) || defined(MACHINE_HI_K0402WS) // Sold as a variety of devices, see doc/
|
|
__code const struct machine machine = {
|
|
.machine_name = "PCB-K0402WS-V3.0",
|
|
.isRTL8373 = 0,
|
|
.min_port = 3,
|
|
.max_port = 8,
|
|
.n_sfp = 2,
|
|
.log_to_phys_port = {0, 0, 0, 6, 1, 2, 3, 4, 5},
|
|
.phys_to_log_port = {4, 5, 6, 7, 8, 3, 0, 0, 0},
|
|
.is_sfp = {0, 0, 0, 2, 0, 0, 0, 0, 1},
|
|
|
|
// Left SFP port
|
|
.sfp_port[0].pin_detect = GPIO38,
|
|
.sfp_port[0].pin_los = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
|
|
// Right SFP port
|
|
.sfp_port[1].pin_detect = GPIO37,
|
|
.sfp_port[1].pin_los = GPIO_NA,
|
|
.sfp_port[1].sds = 0,
|
|
.sfp_port[1].i2c = I2CBUS( GPIO41_I2C_SDA3_MDIO1, GPIO40_I2C_SCL3_MDC1 ),
|
|
|
|
.reset_pin = GPIO_NA,
|
|
.high_leds = { .mux = LED_28_SYS | LED_29, .enable = LED_27 | LED_28_SYS | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 1, 0, 0, 0, 0, 1},
|
|
.led_sets = {
|
|
{
|
|
LEDS_2G5 | LEDS_LINK | LEDS_10M | LEDS_ACT,
|
|
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
|
|
LEDS_1G | LEDS_LINK,
|
|
0
|
|
},
|
|
{
|
|
LEDS_10G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK,
|
|
LEDS_10G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_ACT,
|
|
0,
|
|
0
|
|
},
|
|
},
|
|
.led_mux_custom = 1,
|
|
.led_mux = {
|
|
0x00,0x01,0x04,0x05,0x08,0x09,0x0c,0x3f,0x0d,0x10,0x11,0x0e,0x14,0x11,0x12,0x15,0x15,0x16,0x18,0x19,0x1a,0x19,0x1d,0x1e,0x1c,0x1d,0x20,0x21
|
|
},
|
|
};
|
|
|
|
#elif defined MACHINE_K0501W_V2_0
|
|
__code const struct machine machine = {
|
|
.machine_name = "K0501W V2.0",
|
|
.isRTL8373 = 0,
|
|
.min_port = 3,
|
|
.max_port = 8,
|
|
.n_sfp = 1,
|
|
.log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
|
|
.phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
|
|
.sfp_port[0].pin_los = GPIO37,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
|
|
.reset_pin = GPIO_NA,
|
|
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.led_sets = {
|
|
{
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT,
|
|
0,
|
|
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
0
|
|
},
|
|
{
|
|
LEDS_10G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
0,
|
|
0,
|
|
0
|
|
},
|
|
},
|
|
};
|
|
|
|
#elif defined MACHINE_ZX310S_4T2XH
|
|
__code const struct machine machine = {
|
|
.machine_name = "ZX310S-4T2XH",
|
|
.isRTL8373 = 0,
|
|
.min_port = 3,
|
|
.max_port = 8,
|
|
.n_sfp = 1,
|
|
.n_10g = 1,
|
|
.log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
|
|
.phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.sfp_port[0].pin_detect = GPIO38,
|
|
.sfp_port[0].pin_los = GPIO_NA,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
.reset_pin = GPIO48_I2C_SCL1,
|
|
.high_leds = { .mux = LED_28_SYS, .enable = LED_27 | LED_28_SYS | LED_29 },
|
|
.led_mux_custom = 1,
|
|
.led_mux = { 0x00, 0x01, 0x04, 0x05, 0x08, // 65e0
|
|
0x09, 0x0c, 0x3f, 0x0d, 0x10, // 65e4
|
|
0x11, 0x0e, 0x14, 0x11, 0x12, // 65e8
|
|
0x15, 0x15, 0x16, 0x18, 0x19, // 65ec
|
|
0x1a, 0x19, 0x1d, 0x1e, 0x1c, // 65f0
|
|
0x1d, 0x20, 0x21 },
|
|
.port_led_set = { 0, 0, 0, 1, 0, 0, 0, 0, 1},
|
|
/* Ports 1-4: Orange: 2.5GBit, Green: 10/100/1000MBit
|
|
* Port 5: Blue: 10GBit, Green: 10Mbit-5GBit
|
|
* SFP-port: Blue: 10GBit, Green 100MBit-5GBit
|
|
*/
|
|
.led_sets = { { LEDS_2G5 | LEDS_LINK | LEDS_ACT,
|
|
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
LEDS_DUPLEX,
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT },
|
|
{
|
|
LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_LINK | LEDS_ACT | LEDS_5G,
|
|
LEDS_LINK | LEDS_ACT | LEDS_10G,
|
|
LEDS_2G5 | LEDS_LINK,
|
|
LEDS_COL | LEDS_DUPLEX
|
|
}
|
|
},
|
|
};
|
|
|
|
#elif defined MACHINE_STEAMEMO_IG204_V1
|
|
__code const struct machine machine = {
|
|
.machine_name = "Steamemo IG204 V1",
|
|
.isRTL8373 = 0,
|
|
.min_port = 3,
|
|
.max_port = 8,
|
|
.n_sfp = 2,
|
|
.log_to_phys_port = {0, 0, 0, 6, 1, 2, 3, 4, 5},
|
|
.phys_to_log_port = {4, 5, 6, 7, 8, 3, 0, 0, 0},
|
|
.is_sfp = {0, 0, 0, 2, 0, 0, 0, 0, 1},
|
|
// Left SFP port (5)
|
|
// LED pin 9
|
|
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
|
|
.sfp_port[0].pin_los = GPIO37,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
// Right SFP port (6)
|
|
// LED pin 24
|
|
.sfp_port[1].pin_detect = GPIO50_I2C_SCL2_UART1_TX,
|
|
.sfp_port[1].pin_los = GPIO51_I2C_SDA2_UART1_RX,
|
|
.sfp_port[1].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[1].sds = 0,
|
|
.sfp_port[1].i2c = I2CBUS( GPIO41_I2C_SDA3_MDIO1, GPIO40_I2C_SCL3_MDC1 ),
|
|
.reset_pin = GPIO_NA,
|
|
.high_leds = { .mux = LED_27 | LED_28_SYS | LED_29, .enable = LED_28_SYS | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 1, 0, 0, 0, 0, 1},
|
|
.led_sets = {
|
|
{
|
|
// RJ45 Amber LED (left)
|
|
LEDS_2G5 | LEDS_LINK,
|
|
// RJ45 Green LED (Right)
|
|
LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
0,
|
|
0,
|
|
},
|
|
{
|
|
// SFP LED
|
|
LEDS_10G | LEDS_5G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_LINK | LEDS_ACT,
|
|
0, // unused
|
|
0, // unused
|
|
0
|
|
},
|
|
},
|
|
.led_mux_custom = 1,
|
|
.led_mux = {
|
|
0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x0f, 0x20, 0x0d, 0x0e, 0x10, 0x11, 0x12, 0x14, 0x15, 0x16, 0x18, 0x19, 0x1a, 0x1c, 0x1d, 0x1e, 0x0c, 0x21, 0x22, 0x23
|
|
},
|
|
};
|
|
|
|
#elif defined MACHINE_HI_K0801WS
|
|
__code const struct machine machine = {
|
|
.machine_name = "Hi-Source HI-k0801WS",
|
|
.isRTL8373 = 1,
|
|
.min_port = 0,
|
|
.max_port = 8,
|
|
.n_sfp = 1,
|
|
.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
|
|
.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
|
|
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
|
|
.sfp_port[0].pin_los = GPIO37,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
.reset_pin = GPIO_NA,
|
|
|
|
.high_leds = {
|
|
.mux = LED_27 | LED_29,
|
|
.enable = LED_28_SYS | LED_29
|
|
},
|
|
|
|
/* Ports 1-8 use set 0, port 9 SFP uses set 1 */
|
|
.port_led_set = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
|
|
.led_sets = {
|
|
{ /* Set 0: RJ45 copper ports
|
|
* Amber = 2.5G
|
|
* Green = 1G/100M/10M with activity
|
|
*/
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT, /* Amber */
|
|
0,
|
|
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT, /* Green */
|
|
0
|
|
},
|
|
{ /* Set 1: SFP port, single green LED for all valid speeds */
|
|
LEDS_10G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
0,
|
|
0,
|
|
0
|
|
},
|
|
},
|
|
};
|
|
|
|
#elif defined(MACHINE_PCB_K0402WS_V2) || defined(MACHINE_FNS1200P)
|
|
__code const struct machine machine = {
|
|
#if defined(MACHINE_PCB_K0402WS_V2)
|
|
.machine_name = "PCB-K0402WS-V2.0",
|
|
#else
|
|
.machine_name = "FNS-1200P",
|
|
#endif
|
|
.isRTL8373 = 0,
|
|
.min_port = 3,
|
|
.max_port = 8,
|
|
.n_sfp = 2,
|
|
.log_to_phys_port = {0, 0, 0, 6, 1, 2, 3, 4, 5},
|
|
.phys_to_log_port = {4, 5, 6, 7, 8, 3, 0, 0, 0},
|
|
.is_sfp = {0, 0, 0, 2, 0, 0, 0, 0, 1},
|
|
|
|
/* Left SFP (logical 8, SDS1): GPIO30=ModAbs, GPIO37=RX_LOS */
|
|
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
|
|
.sfp_port[0].pin_los = GPIO37,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
|
|
/* Right SFP (logical 3, SDS0): GPIO50=ModAbs, GPIO51=RX_LOS */
|
|
.sfp_port[1].pin_detect = GPIO50_I2C_SCL2_UART1_TX,
|
|
.sfp_port[1].pin_los = GPIO51_I2C_SDA2_UART1_RX,
|
|
.sfp_port[1].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[1].sds = 0,
|
|
.sfp_port[1].i2c = I2CBUS( GPIO41_I2C_SDA3_MDIO1, GPIO40_I2C_SCL3_MDC1 ),
|
|
|
|
.reset_pin = GPIO_NA,
|
|
|
|
.high_leds = { .mux = LED_27 | LED_28_SYS | LED_29, .enable = LED_28_SYS | LED_29 },
|
|
|
|
/* Copper ports use SET0; SFP ports use SET1 */
|
|
.port_led_set = {0, 0, 0, 1, 0, 0, 0, 0, 1},
|
|
|
|
.led_sets = {
|
|
{ /* SET0: copper — LED0=amber (2.5G), LED2=green (1G/100M/10M) */
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT,
|
|
0,
|
|
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
0
|
|
},
|
|
{ /* SET1: SFP — all speeds link/act */
|
|
LEDS_10G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
0,
|
|
0, 0
|
|
},
|
|
},
|
|
|
|
.led_mux_custom = 1,
|
|
.led_mux = {
|
|
0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, /* GPIO0-7: unused */
|
|
0x0f, 0x0c, 0x0d, 0x0e, 0x10, 0x11, 0x12, /* GPIO8-14 */
|
|
0x14, 0x15, 0x16, 0x18, 0x19, 0x1a, /* GPIO15-20 */
|
|
0x1c, 0x1d, 0x1e, 0x20, 0x21, 0x22, 0x23 /* GPIO21-27 */
|
|
},
|
|
};
|
|
|
|
|
|
#elif defined MACHINE_PCB_SWTG024AS_A_2_0_1
|
|
__code const struct machine machine = {
|
|
.machine_name = "PCB-SWTG024AS-A-2.0.1",
|
|
.isRTL8373 = 0,
|
|
.min_port = 3,
|
|
.max_port = 8,
|
|
.n_sfp = 2,
|
|
.log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
|
|
.phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
|
|
.is_sfp = {0, 0, 0, 1, 0, 0, 0, 0, 2},
|
|
|
|
// SFP port on SDS0 / logical port 3
|
|
.sfp_port[0].pin_detect = GPIO37,
|
|
.sfp_port[0].pin_los = GPIO_NA,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 0,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO41_I2C_SDA3_MDIO1, GPIO40_I2C_SCL3_MDC1 ),
|
|
|
|
// SFP port on SDS1 / logical port 8
|
|
.sfp_port[1].pin_detect = GPIO38,
|
|
.sfp_port[1].pin_los = GPIO_NA,
|
|
.sfp_port[1].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[1].sds = 1,
|
|
.sfp_port[1].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
|
|
.reset_pin = GPIO_NA,
|
|
.high_leds = { .mux = LED_28_SYS | LED_29, .enable = LED_27 | LED_28_SYS | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 1, 0, 0, 0, 0, 1},
|
|
.led_sets = {
|
|
{
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT,
|
|
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
LEDS_DUPLEX,
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT
|
|
},
|
|
{
|
|
LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_LINK | LEDS_ACT,
|
|
LEDS_10G | LEDS_LINK | LEDS_ACT,
|
|
LEDS_2G5 | LEDS_LINK,
|
|
LEDS_COL | LEDS_DUPLEX
|
|
},
|
|
},
|
|
.led_mux_custom = 1,
|
|
.led_mux = {
|
|
0x00,0x01,0x04,0x05,0x08,0x09,0x0c,0x3f,0x0d,0x10,0x11,0x0e,0x14,0x11,0x12,0x15,0x15,0x16,0x18,0x19,0x1a,0x19,0x1d,0x1e,0x1c,0x1d,0x20,0x21
|
|
},
|
|
};
|
|
|
|
#elif defined MACHINE_SWTG024AS_A_2_0_1_5C_1SFP
|
|
__code const struct machine machine = {
|
|
.machine_name = "SWTG024AS-A-V2.0.1-5C-1SFP",
|
|
.isRTL8373 = 0,
|
|
.min_port = 3,
|
|
.max_port = 8,
|
|
.n_sfp = 1,
|
|
.log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
|
|
.phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.sfp_port[0].pin_detect = GPIO38,
|
|
.sfp_port[0].pin_los = GPIO_NA,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
|
|
.reset_pin = GPIO_NA,
|
|
.high_leds = { .mux = LED_28_SYS | LED_29, .enable = LED_27 | LED_28_SYS | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
/* Ports 1-5 RJ45 use set 0, port 9 SFP uses set 1
|
|
* Ports 1-5: Green: 2.5GBit, Amber: 10/100/1000MBit
|
|
* SFP-port: Blue: 10GBit, Green: 100MBit-2.5GBit
|
|
*/
|
|
.led_sets = {
|
|
{
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT,
|
|
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
LEDS_DUPLEX,
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT
|
|
},
|
|
{
|
|
LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_LINK | LEDS_ACT,
|
|
LEDS_10G | LEDS_LINK | LEDS_ACT,
|
|
LEDS_2G5 | LEDS_LINK,
|
|
LEDS_COL | LEDS_DUPLEX
|
|
},
|
|
},
|
|
.led_mux_custom = 1,
|
|
.led_mux = {
|
|
0x00,0x01,0x04,0x05,0x08,0x09,0x0c,0x3f,0x0d,0x10,0x11,0x0e,0x14,0x11,0x12,0x15,0x15,0x16,0x18,0x19,0x1a,0x19,0x1d,0x1e,0x1c,0x1d,0x20,0x21
|
|
},
|
|
};
|
|
|
|
#elif defined MACHINE_SWTG024AS_V2_0
|
|
__code const struct machine machine = {
|
|
.machine_name = "SWTG024AS-V2.0",
|
|
.isRTL8373 = 0,
|
|
.min_port = 3,
|
|
.max_port = 8,
|
|
.n_sfp = 1,
|
|
.log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
|
|
.phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
|
|
.sfp_port[0].pin_los = GPIO37,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
|
|
.reset_pin = GPIO_NA,
|
|
.high_leds = { .mux = LED_28_SYS | LED_29, .enable = LED_27 | LED_28_SYS | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
/* Ports 1-5 RJ45 use set 0, port 9 SFP uses set 1
|
|
* Ports 1-5: Green: 2.5GBit, Amber: 10/100/1000MBit
|
|
* SFP-port: Blue: 10GBit, Amber: 100MBit-2.5GBit
|
|
*/
|
|
.led_sets = {
|
|
{
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT,
|
|
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
LEDS_DUPLEX,
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT
|
|
},
|
|
{
|
|
LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_LINK | LEDS_ACT,
|
|
LEDS_10G | LEDS_LINK | LEDS_ACT,
|
|
LEDS_2G5 | LEDS_LINK,
|
|
LEDS_COL | LEDS_DUPLEX
|
|
},
|
|
},
|
|
.led_mux_custom = 1,
|
|
.led_mux = {
|
|
0x00,0x01,0x04,0x05,0x08,0x09,0x0c,0x3f,0x0d,0x10,0x11,0x0e,0x14,0x11,0x12,0x15,0x15,0x16,0x18,0x19,0x1a,0x19,0x1d,0x1e,0x1c,0x1d,0x20,0x21
|
|
},
|
|
};
|
|
|
|
#elif defined MACHINE_ZX310S_4T2XT
|
|
__code const struct machine machine = {
|
|
.machine_name = "ZX310S_4T2XT",
|
|
.isRTL8373 = 0,
|
|
.min_port = 3,
|
|
.max_port = 8,
|
|
.n_sfp = 0,
|
|
.n_10g = 2,
|
|
.log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
|
|
.phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 0},
|
|
.reset_pin = GPIO48_I2C_SCL1,
|
|
.high_leds = { .mux = LED_28_SYS | LED_29, .enable = LED_27 | LED_28_SYS | LED_29 },
|
|
.led_mux_custom = 1,
|
|
.led_mux = { 0x00, 0x01, 0x04, 0x05, 0x08, // 65e0
|
|
0x09, 0x0c, 0x3f, 0x0d, 0x10, // 65e4
|
|
0x11, 0x0e, 0x14, 0x11, 0x12, // 65e8
|
|
0x15, 0x15, 0x16, 0x18, 0x19, // 65ec
|
|
0x1a, 0x19, 0x1d, 0x1e, 0x1c, // 65f0
|
|
0x1d, 0x20, 0x21 },
|
|
.port_led_set = { 0, 0, 0, 1, 0, 0, 0, 0, 1},
|
|
/* Ports 1-4: Green: 2.5GBit, Orange: 10/100/1000MBit
|
|
* Ports 5-6: Green: 10GBit, Orange: <= 5GBit
|
|
*/
|
|
.led_sets = { { LEDS_2G5 | LEDS_LINK | LEDS_ACT,
|
|
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
LEDS_DUPLEX,
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT },
|
|
{
|
|
LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_LINK | LEDS_ACT,
|
|
LEDS_LINK | LEDS_ACT | LEDS_10G | LEDS_5G,
|
|
LEDS_2G5 | LEDS_LINK,
|
|
LEDS_COL | LEDS_DUPLEX
|
|
}
|
|
},
|
|
};
|
|
|
|
#elif defined MACHINE_FG_4GT_2SX_V2_0
|
|
__code const struct machine machine = {
|
|
.machine_name = "FG-4GT-2SX_V2.0",
|
|
.isRTL8373 = 0,
|
|
.min_port = 3,
|
|
.max_port = 8,
|
|
.n_sfp = 2,
|
|
.log_to_phys_port = {0, 0, 0, 6, 1, 2, 3, 4, 5},
|
|
.phys_to_log_port = {4, 5, 6, 7, 8, 3, 0, 0, 0},
|
|
.is_sfp = {0, 0, 0, 2, 0, 0, 0, 0, 1},
|
|
|
|
// Left SFP port
|
|
.sfp_port[0].pin_detect = GPIO38,
|
|
.sfp_port[0].pin_los = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
|
|
// Right SFP port
|
|
.sfp_port[1].pin_detect = GPIO37,
|
|
.sfp_port[1].pin_los = GPIO_NA,
|
|
.sfp_port[1].sds = 0,
|
|
.sfp_port[1].i2c = I2CBUS( GPIO41_I2C_SDA3_MDIO1, GPIO40_I2C_SCL3_MDC1 ),
|
|
|
|
.reset_pin = GPIO_NA,
|
|
.high_leds = { .mux = LED_27 | LED_28_SYS | LED_29, .enable = LED_28_SYS | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 1, 0, 0, 0, 0, 1},
|
|
/* Ports 1-4 RJ45 use set 0, port 5-6 SFP uses set 1
|
|
* Ports 1-4: Green: 2.5GBit, Amber: 10/100/1000MBit
|
|
* Ports 5-6: Green: 100MBit-10GBit
|
|
*/
|
|
.led_sets = {
|
|
{
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT,
|
|
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
0,
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT
|
|
},
|
|
{
|
|
LEDS_10G | LEDS_5G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
LEDS_10G | LEDS_LINK,
|
|
0,
|
|
LEDS_COL | LEDS_DUPLEX
|
|
},
|
|
{
|
|
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
LEDS_2G5 | LEDS_1G | LEDS_LINK,
|
|
LEDS_5G | LEDS_2G5 | LEDS_LINK | LEDS_ACT,
|
|
LEDS_10G | LEDS_LINK | LEDS_ACT
|
|
},
|
|
{
|
|
LEDS_TX,
|
|
LEDS_RX,
|
|
LEDS_10G | LEDS_TWO_PAIR_5G | LEDS_5G | LEDS_TWO_PAIR_2G5 |
|
|
LEDS_2G5 | LEDS_TWO_PAIR_1G | LEDS_1G | LEDS_500M | LEDS_100M | LEDS_10M | LEDS_ACT,
|
|
LEDS_10G | LEDS_TWO_PAIR_5G | LEDS_5G | LEDS_TWO_PAIR_2G5 |
|
|
LEDS_2G5 | LEDS_TWO_PAIR_1G | LEDS_1G | LEDS_500M | LEDS_100M | LEDS_10M | LEDS_LINK
|
|
},
|
|
},
|
|
.led_mux_custom = 1,
|
|
.led_mux = {
|
|
0x0c, 0x0d, 0x0e, 0x10, 0x11, 0x12, 0x14, 0x3f, 0x15, 0x16,
|
|
0x18, 0x0e, 0x19, 0x11, 0x12, 0x1a, 0x15, 0x16, 0x1c, 0x19,
|
|
0x1a, 0x1d, 0x1d, 0x1e, 0x1e, 0x20, 0x21, 0x22
|
|
},
|
|
};
|
|
|
|
#elif defined MACHINE_FG_8GT_1SX
|
|
__code const struct machine machine = {
|
|
.machine_name = "FG-8GT-1SX",
|
|
.isRTL8373 = 1,
|
|
.min_port = 0,
|
|
.max_port = 8,
|
|
.n_sfp = 1,
|
|
.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
|
|
.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.sfp_port[0].pin_detect = GPIO38,
|
|
.sfp_port[0].pin_los = GPIO_NA,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
.reset_pin = GPIO_NA,
|
|
.high_leds = { .mux = LED_27 | LED_28_SYS | LED_29, .enable = LED_28_SYS | LED_29 },
|
|
.port_led_set = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.led_sets = {
|
|
/*
|
|
Ports 1-8: Left Amber 10/100/1000MBit (Vendor no 10M, but we add it)
|
|
Right Green 2.5GBit
|
|
SFP-port: Any speed
|
|
*/
|
|
{
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT,
|
|
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
0,
|
|
0,
|
|
},
|
|
{
|
|
LEDS_10G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
0,
|
|
0,
|
|
0,
|
|
},
|
|
},
|
|
.led_mux_custom = 1,
|
|
.led_mux = {
|
|
0x00, 0x01, 0x04, 0x05, 0x08, 0x09, 0x0c, 0x09, 0x0d, 0x10,
|
|
0x11, 0x0e, 0x14, 0x11, 0x12, 0x15, 0x15, 0x16, 0x18, 0x19,
|
|
0x1a, 0x19, 0x1d, 0x1e, 0x1c, 0x1d, 0x20, 0x21,
|
|
},
|
|
};
|
|
|
|
#elif defined MACHINE_LIANGUO_HYWS_SGT0108S
|
|
__code const struct machine machine = {
|
|
.machine_name = "Lianguo HYWS-SGT0108S",
|
|
.isRTL8373 = 1,
|
|
.min_port = 0,
|
|
.max_port = 8,
|
|
.n_sfp = 1,
|
|
.log_to_phys_port = {2, 1, 4, 3, 5, 6, 7, 8, 9},
|
|
.phys_to_log_port = {1, 0, 3, 2, 4, 5, 6, 7, 8},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
|
|
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
|
|
.sfp_port[0].pin_los = GPIO37,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
|
|
.reset_pin = GPIO_NA,
|
|
.high_leds = { .mux = 0, .enable = 0 },
|
|
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1 },
|
|
.led_sets = {
|
|
{
|
|
LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT, // RJ45 Blue LEDs
|
|
LEDS_2G5 | LEDS_LINK, // RJ45 White LEDs
|
|
0,
|
|
0
|
|
},
|
|
{
|
|
LEDS_10G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT, // SFP blue LED?
|
|
0,
|
|
0,
|
|
0
|
|
},
|
|
},
|
|
};
|
|
#elif defined MACHINE_POE_2G080110GS
|
|
__code const struct machine machine = {
|
|
.machine_name = "MokerLink POE-2G080110GS",
|
|
.isRTL8373 = 1,
|
|
.min_port = 0,
|
|
.max_port = 8,
|
|
.n_sfp = 1,
|
|
.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
|
|
.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
|
|
.sfp_port[0].pin_los = GPIO37,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
.reset_pin = GPIO_NA,
|
|
.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28_SYS | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.led_sets = {
|
|
{
|
|
/* SET0: RJ45 2.5G = amber, 1G/100M/10M = green */
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT, /* amber */
|
|
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT, /* green */
|
|
0,
|
|
0
|
|
},
|
|
{
|
|
/* SET1: SFP+ port = green */
|
|
LEDS_2G5 | LEDS_TWO_PAIR_1G | LEDS_1G | LEDS_500M | LEDS_100M | LEDS_10M |
|
|
LEDS_LINK | LEDS_ACT | LEDS_10G | LEDS_TWO_PAIR_5G | LEDS_5G | LEDS_TWO_PAIR_2G5,
|
|
0,
|
|
0,
|
|
0
|
|
}
|
|
},
|
|
.led_mux_custom = 1,
|
|
.led_mux = { 0x00, 0x01, 0x04, 0x05, 0x08,
|
|
0x09, 0x0c, 0x09, 0x0d, 0x10,
|
|
0x11, 0x0e, 0x14, 0x11, 0x12,
|
|
0x15, 0x15, 0x16, 0x18, 0x19,
|
|
0x1a, 0x19, 0x1d, 0x1e, 0x1c,
|
|
0x1d, 0x20, 0x21 },
|
|
};
|
|
#elif defined MACHINE_PB_2132
|
|
__code const struct machine machine = {
|
|
.machine_name = "PB-2132",
|
|
.isRTL8373 = 1,
|
|
.min_port = 0,
|
|
.max_port = 8,
|
|
.n_sfp = 1,
|
|
.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
|
|
.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
|
|
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
|
|
.sfp_port[0].pin_los = GPIO37,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
|
|
.reset_pin = GPIO_NA,
|
|
|
|
.high_leds = { .mux = LED_27 | LED_28_SYS | LED_29, .enable = LED_28_SYS | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
|
|
.led_sets = {
|
|
{
|
|
/* LED0 = RJ45: Amber LED: 2.5G */
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT,
|
|
/* LED1 = RJ45: Green LED: 10M / 100M / 1000M */
|
|
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
0,
|
|
0
|
|
},
|
|
{
|
|
/* SFP+ single Green LED. */
|
|
LEDS_10G | LEDS_5G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_LINK | LEDS_ACT,
|
|
0,
|
|
0,
|
|
0
|
|
},
|
|
},
|
|
};
|
|
|
|
#elif defined MACHINE_HASIVO_S600W_4GT_2XGT_SE
|
|
__code const struct machine machine = {
|
|
.machine_name = "Hasivo S600W-4GT-2XGT-SE",
|
|
.isRTL8373 = 0,
|
|
.min_port = 3,
|
|
.max_port = 8,
|
|
.n_sfp = 0,
|
|
.n_10g = 2,
|
|
.log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
|
|
.phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 0},
|
|
.reset_pin = GPIO54_ACL_BIT2_EN,
|
|
.high_leds = { .mux = LED_28_SYS | LED_29, .enable = LED_28_SYS | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 1, 0, 0, 0, 0, 1 },
|
|
/* Ports 1-4: Green: 2.5GBit, Orange: 10/100/1000MBit
|
|
* Ports 5-6: Green: 10GBit, Orange: 5/2.5GBit, None: 10/100/1000MBit
|
|
*/
|
|
.led_sets = {
|
|
{
|
|
LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT, // Yellow
|
|
LEDS_2G5 | LEDS_LINK, // Green
|
|
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK, // Orange
|
|
0, // Unused
|
|
},
|
|
{
|
|
LEDS_10G | LEDS_5G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT, // Yellow
|
|
LEDS_10G | LEDS_LINK, // Green
|
|
LEDS_5G | LEDS_2G5 | LEDS_LINK, // Orange
|
|
0, // Unused
|
|
},
|
|
},
|
|
.led_mux_custom = 1,
|
|
.led_mux = {
|
|
0x3f, 0x3f, 0x3f, 0x3f, 0x3f,
|
|
0x3f, 0x3f, 0x3f, 0x0f, 0x20,
|
|
0x21, 0x22, 0x10, 0x11, 0x12,
|
|
0x14, 0x15, 0x16, 0x18, 0x19,
|
|
0x1a, 0x1c, 0x1d, 0x1e, 0x0c,
|
|
0x0d, 0x0e, 0x23
|
|
},
|
|
|
|
};
|
|
#elif defined MACHINE_HASIVO_S1100WP_8GT_1SX_SE
|
|
__code const struct machine machine = {
|
|
.machine_name = "Hasivo S1100WP-8GT-1SX-SE",
|
|
.isRTL8373 = 1,
|
|
.mac_flash_offset = 0x1FC000,
|
|
.min_port = 0,
|
|
.max_port = 8,
|
|
.n_sfp = 1,
|
|
.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
|
|
.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
|
|
.sfp_port[0].pin_los = GPIO37,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
.reset_pin = GPIO54_ACL_BIT2_EN,
|
|
.high_leds = { .mux = LED_27 | LED_28_SYS | LED_29, .enable = LED_28_SYS | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.led_sets = { { LEDS_2G5 | LEDS_LINK | LEDS_ACT, // Green LED (right)
|
|
0,
|
|
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT, // Amber LED (left)
|
|
0
|
|
},
|
|
{ LEDS_10G | LEDS_5G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_LINK | LEDS_ACT, // SFP LED
|
|
0,
|
|
0,
|
|
0
|
|
},
|
|
},
|
|
};
|
|
#elif defined MACHINE_F7008_2_5
|
|
__code const struct machine machine = {
|
|
.machine_name = "F7008-2.5 8+1 SFP Port Switch",
|
|
.isRTL8373 = 1,
|
|
.min_port = 0,
|
|
.max_port = 8,
|
|
.n_sfp = 1,
|
|
.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
|
|
.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
|
|
.sfp_port[0].pin_los = GPIO37,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
|
|
.reset_pin = GPIO_NA,
|
|
.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28_SYS | LED_29 },
|
|
.port_led_set = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.led_sets = {
|
|
{ /* SET0 */
|
|
LEDS_2G5 | LEDS_LINK, /* LEDID0 - green: 2.5G link */
|
|
LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT, /* LEDID1 - yellow: traffic */
|
|
0,
|
|
0,
|
|
},
|
|
{ /* SET1 - SFP+ */
|
|
LEDS_10G | LEDS_5G | LEDS_2G5 | LEDS_LINK,
|
|
LEDS_10G | LEDS_5G | LEDS_2G5 | LEDS_1G | LEDS_LINK | LEDS_ACT,
|
|
0,
|
|
0,
|
|
},
|
|
},
|
|
.led_mux_custom = 1,
|
|
.led_mux = {
|
|
0x00, 0x01, 0x04, 0x05, 0x08, 0x09, 0x0c, 0x02,
|
|
0x0d, 0x10, 0x11, 0x02, 0x14, 0x02, 0x02, 0x15,
|
|
0x02, 0x02, 0x18, 0x02, 0x02, 0x19, 0x02, 0x02,
|
|
0x1c, 0x1d, 0x02, 0x02,
|
|
},
|
|
};
|
|
|
|
#else
|
|
#error "Please select a machine type in machine.h"
|
|
#endif
|