Add support for the ZX_SWTGW215AS device built by Hasivo

The device is sold under the name ZX_SWTGW215AS without necessarily a Hasivo branding, however the firmware and the PCB are marked with Hasivo. The PCB is marked Hasivo RTL_SGT-1SX V1.5 SoC: RTL8372 Ethernet: 5 x 2.5GBit (RTL8221B + 4*SoC) SFP+: 1x 10GBit (SoC) The device has a slider switch and a reset button. Reset: GPIO 54 (active-low) Slider: GPIO 51 (right is high)
Add LED-pad mapping
2026-10-29 17:54:14 +08:00 · 2026-02-06 07:19:12 +01:00 · 2026-02-05 19:41:28 +01:00 · 2026-02-03 19:24:36 +01:00 · 2026-02-01 22:15:12 +01:00 · 2026-02-01 22:15:12 +01:00
369 changed files with 4821 additions and 22604 deletions
@@ -1,19 +0,0 @@
-.git/
-.gitignore
-.gitattributes
-.github/
-output/
-installer/output/
-*.bin
-html_data.c
-html_data.h
-*.o
-*.rel
-*.lst
-*.sym
-*.asm
-*.ihx
-*.img
-*.map
-*.mem
-*.lk
@@ -3,7 +3,6 @@ name: Build firmware
 on:
  push:
    branches: ['**']
-  pull_request:

 jobs:
  build:
@@ -17,14 +16,6 @@ jobs:
      - name: Install dependencies
        run: |
          apt update
-          apt install make gcc sdcc xxd python-is-python3 libjson-c-dev zlib1g-dev -y
-      - name: Run the host-side unit tests
-        run: make -C test
-      - name: Check that every machine definition can be compiled
-        run: make machine_check
-      - name: Make project (4x2/RTL8372)
-        run: make CI=1 MACHINE="KP_9000_6XHML_X2"
-      - name: Make project (8x1/RTL8373)
-        run: make CI=1 MACHINE="KP_9000_9XHML_X_V3_1"
-      - name: Make project with the health instrumentation
-        run: make clean && make CI=1 MACHINE="KP_9000_6XHML_X2" HEALTH=1
+          apt install make gcc sdcc xxd python-is-python3 libjson-c-dev -y
+      - name: Make project
+        run: make
@@ -7,7 +7,3 @@ version.h
 tools/httpd_sim
 tools/injector
 tools/fileadder
-
-# host-test stand-ins for the two generated headers
-!test/stub/html_data.h
-!test/stub/version.h
@@ -1,37 +0,0 @@
-# Change Log
-
-## [0.x] - 2026-xx-XX
-
-## Added
-
- Web UI
-  - Compress the embedded assets (minify + gzip) and switch to a single-page layout. #315
-  - Replace the multi-page UI with a themed single-page app: light, dark and Selenized themes following the browser by default,
-    English, Japanese and Chinese, save to flash merges the command log into the startup config and verifies the write,
-    firmware images are checked in the browser before upload. #429
-
-## Changed
-
-## Fixed
-
- Config
-  - A startup configuration line longer than the command buffer no longer stops the replay:
-    the offending line is skipped and the following lines are still applied.
-  - The web UI and the configuration upload now refuse a line the replay cannot take,
-    instead of writing it to flash.
-
-## Breaking changes
-
- Config
-  - VLAN don't accept port `u`-suffix anymore.
-    So `vlan 1 4u` is not valid anymore.
-    Replace it with `vlan 1 4`.
- Commands
-  - port zero/`0` is treated as the `CPU_PORT`. #326
-  - Many commands don't accept the CPU_PORT anymore. See #334.
-    When the CPU_PORT is needed, the command/service will add the CPU_PORT automaticly.
-    Only `isolate` accept the CPU_PORT as destination port.
-
-## [v0.1_aplha] - 2025-11-03
-
-First release.
@@ -1,19 +0,0 @@
-FROM debian:13-slim
-
-RUN apt-get update && apt-get install -y \
-    make \
-    gcc \
-    sdcc \
-    xxd \
-    python3 \
-    libjson-c-dev \
-    git \
-    zlib1g-dev \
-    && rm -rf /var/lib/apt/lists/*
-
-# git safe.directory for mounted repos (Makefile uses git describe)
-RUN git config --global --add safe.directory /workspace
-
-WORKDIR /workspace
-
-CMD ["bash"]
@@ -1,223 +1,75 @@
+BOOTLOADER_ADDRESS=0x100
+
 VERSION=0.1.0
 IMAGESIZE = 524288
-DEFAULT_CONFIG_LOCATION = 454656
 CONFIG_LOCATION = 458752
 HTML_LOCATION = 262144

-ifeq ($(origin CC),default)
 CC = sdcc
-endif
-CC_FLAGS = -mmcs51 -I. -Imachine -Ihttpd -Iuip
-ASM ?= sdas8051
+CC_FLAGS = -mmcs51 -I. -Ihttpd -Iuip
+ASM = sdas8051
 AFLAGS= -plosgff

-SUBDIRS := tools
+SUBDIRS := tools uip httpd
 SUBDIRSCLEAN=$(addsuffix clean,$(SUBDIRS))

-# $MACHINE selects machine/$(MACHINE).c as the board definition and is passed
-# on as -DMACHINE_$(MACHINE), which the rest of the firmware tests with
-# #if defined(MACHINE_...), and as -DMACHINE_NAME, which machine.h uses to
-# include machine/$(MACHINE).h. Both take the same value, so they cannot drift.
-ifneq ($(MACHINE),)
-	CC_FLAGS += -DMACHINE_$(MACHINE)
-	CC_FLAGS += -DMACHINE_NAME=$(MACHINE)
-endif
-# Health instrumentation and the "health" console command: HEALTH=1 gmake ...
-ifneq ($(HEALTH),)
-	CC_FLAGS += -DHEALTH
-endif
-
-ifeq ($(CI),1)
-	CC_FLAGS += --Werror
-endif
-
-# The board definition being built: one file per MACHINE_* symbol in machine.h.
-MACHINE_SRC = machine/$(MACHINE).c
-
-BUILDDIR = output/$(MACHINE)
+BUILDDIR = output/
 VERSION_HEADER := version.h

-GIT_VERSION := $(shell git rev-parse --short HEAD)
-ifeq ($(shell git status --porcelain --untracked-files=no),)
-else
-	GIT_VERSION := $(GIT_VERSION)-dirty
-endif
-
-VERSION_EXTENSION = v$(VERSION)-$(GIT_VERSION)
-FILENAME_EXTENSION = $(VERSION_EXTENSION)-$(MACHINE)
-
-# Deterministic build date: honor SOURCE_DATE_EPOCH, else the HEAD commit date,
-# else wall-clock (no-git fallback). Keeps same-commit builds byte-identical
-# (BUILD_DATE is baked into the image and covered by the trailing CRC).
-SOURCE_DATE_EPOCH ?= $(shell git show -s --format=%ct HEAD 2>/dev/null)
-ifeq ($(SOURCE_DATE_EPOCH),)
-BUILD_DATE := $(shell date +"%Y-%m-%d %H:%M:%S")
-else
-BUILD_DATE := $(shell date -u -d @$(SOURCE_DATE_EPOCH) +"%Y-%m-%d %H:%M:%S" 2>/dev/null \
-	|| date -u -r $(SOURCE_DATE_EPOCH) +"%Y-%m-%d %H:%M:%S")
-endif
-
-# $(MACHINE_SRC) is listed here so an unknown $MACHINE fails before anything else
-# is built, including the tools/ subdirectory.
-all: create_build_dir $(VERSION_HEADER) $(MACHINE_SRC) $(SUBDIRS) $(BUILDDIR)/rtlplayground-$(FILENAME_EXTENSION).bin
+all: create_build_dir $(VERSION_HEADER) $(SUBDIRS) $(BUILDDIR)rtlplayground.bin

 create_build_dir:
-	mkdir -p "$(BUILDDIR)"
-	mkdir -p "$(BUILDDIR)/uip"
-	mkdir -p "$(BUILDDIR)/httpd"
-	mkdir -p "$(BUILDDIR)/machine"
+	mkdir -p $(BUILDDIR)

-# Every machine is a pair machine/<MACHINE>.c + machine/<MACHINE>.h. Selecting
-# them by name means no #if/#elif chain, so an unknown or empty $MACHINE is
-# caught here instead of by a #error further down the build.
-$(MACHINE_SRC):
-	@echo "ERROR: MACHINE='$(MACHINE)' has no definition (expected $(MACHINE_SRC))." >&2
-	@echo "       Every machine is one file pair under machine/, named after the" >&2
-	@echo "       MACHINE_* symbol it defines; see machine/*.c for the full list." >&2
-	@echo "       Example: make MACHINE=KP_9000_6XHML_X2" >&2
-	@false
+SRCS = rtlplayground.c rtl837x_flash.c rtl837x_leds.c rtl837x_phy.c rtl837x_port.c cmd_parser.c html_data.c rtl837x_igmp.c rtl837x_stp.c rtl837x_pins.c dhcp.c machine.c
+OBJS = ${SRCS:%.c=$(BUILDDIR)%.rel}
+OBJS += uip/$(BUILDDIR)/timer.rel uip/$(BUILDDIR)/uip-fw.rel uip/$(BUILDDIR)/uip-neighbor.rel uip/$(BUILDDIR)/uip-split.rel uip/$(BUILDDIR)/uip.rel uip/$(BUILDDIR)/uip_arp.rel uip/$(BUILDDIR)/uiplib.rel httpd/$(BUILDDIR)/httpd.rel httpd/$(BUILDDIR)/page_impl.rel

-# Keep the per-machine definition in first position to fail immediately on an
-# invalid $MACHINE value
-SRCS = \
-	$(MACHINE_SRC) \
-	machine_init.c \
-	cmd_editor.c \
-	cmd_parser.c \
-	dhcp.c \
-	html_data.c \
-	rtlplayground.c \
-	boot.c \
-	sfp.c \
-	dns.c \
-	dns_cli.c \
-	ntp.c \
-	ntp_cli.c \
-	syslog.c \
-	udp_apps.c
+html_data.c html_data.h: html tools
+	tools/$(BUILDDIR)fileadder -a $(HTML_LOCATION) -s $(IMAGESIZE) -b BANK1 -d html -p html_data

-# RTL837x
-SRCS += \
-	rtl837x_bandwidth.c \
-	rtl837x_cabletest.c \
-	rtl837x_flash.c \
-	rtl837x_igmp.c \
-	rtl837x_init.c \
-	rtl837x_leds.c \
-	rtl837x_leds_dump.c \
-	rtl837x_phy.c \
-	rtl837x_pins.c\
-	rtl837x_port.c \
-	rtl837x_stp.c \
-	rtl837x_lldp.c \
-	rtl837x_storm.c \
-	rtl837x_lacp.c \
-	rtl837x_trap.c
-SRCS += \
-	httpd/httpd.c \
-	httpd/page_impl.c
-SRCS += \
-	uip/timer.c \
-	uip/uip.c \
-	uip/uiplib.c \
-	uip/uip_arp.c \
-	uip/uip-fw.c \
-	uip/uip-neighbor.c \
-	uip/uip-split.c
-
-OBJS = ${SRCS:%.c=$(BUILDDIR)/%.rel}
-DEPS := ${SRCS:%.c=$(BUILDDIR)/%.d}
-HTML := $(shell find html -name '*.js' -or -name '*.html' -or -name '*.svg' -or -name '*.css' -or -name '*.ico')
-
-# Minified copy of the web UI sources, used as the fileadder input.
-# The raw html/ sources stay untouched for development; the minified
-# copy is a build artifact under output/.
-HTML_MIN := output/html_min
-.PHONY: html_min
-html_min: $(HTML)
-	rm -rf $(HTML_MIN)
-	mkdir -p $(HTML_MIN)
-	@for f in $(HTML); do python3 tools/minify.py $$f $(HTML_MIN)/$$(basename $$f) || exit 1; done
-
-html_data.c html_data.h &: $(HTML) | tools html_min
-	tools/output/fileadder -a $(HTML_LOCATION) -s $(IMAGESIZE) -b BANK1 -z -d $(HTML_MIN) -p html_data
-
-$(VERSION_HEADER): FORCE
-	@printf '%s\n' "#ifndef VERSION_H" "#define VERSION_H" \
-		"#define VERSION_SW \"$(VERSION_EXTENSION)\"" \
-		"#define BUILD_DATE \"$(BUILD_DATE)\"" \
-		"#endif" > $(VERSION_HEADER).tmp
-	@cmp -s $(VERSION_HEADER).tmp $(VERSION_HEADER) \
-		&& rm -f $(VERSION_HEADER).tmp \
-		|| mv $(VERSION_HEADER).tmp $(VERSION_HEADER)
+$(VERSION_HEADER):
+	@echo "#ifndef VERSION_H" > $(VERSION_HEADER)
+	@echo "#define VERSION_H" >> $(VERSION_HEADER)
+	@echo "#define VERSION_SW \"v$(VERSION)-g$(shell git rev-parse --short HEAD)\"" >> $(VERSION_HEADER)
+	@echo "#endif" >> $(VERSION_HEADER)

 httpd: html_data.h

 $(SUBDIRS):
 	$(MAKE) -C $@

-clean: $(SUBDIRSCLEAN)
-	-rm -f html_data.c html_data.h $(VERSION_HEADER)
-	-if [ -d $(BUILDDIR) ]; then find $(BUILDDIR) -type f ! -name "*.bin" -delete; fi
+clean:
+	-make -C uip clean
+	-make -C httpd clean
+	-rm html_data.c html_data.h $(VERSION_HEADER)
+	-rm -r $(BUILDDIR)

-distclean: $(SUBDIRSCLEAN)
-	-rm -f html_data.c html_data.h $(VERSION_HEADER)
-	-rm -rf $(BUILDDIR)
+$(BUILDDIR)crtstart.rel: crtstart.asm
+	$(ASM) $(AFLAGS) -o $@ $<

-$(SUBDIRSCLEAN):
-	$(MAKE) -C $(@:clean=) clean
+$(BUILDDIR)crc16.rel: crc16.asm
+	$(ASM) $(AFLAGS) -o $@ $<

-# Objects depend on the flags they were built with, through a stamp file that
-# is rewritten only when CC_FLAGS actually changes.
-CCFLAGS_STAMP := $(BUILDDIR)/.ccflags
+$(BUILDDIR)%.rel: %.c
+	$(CC) $(CC_FLAGS) -o $@ -c $<

-.PHONY: FORCE
-FORCE:
-
-$(CCFLAGS_STAMP): FORCE | create_build_dir
-	@echo '$(CC_FLAGS)' | cmp -s - $@ 2>/dev/null || echo '$(CC_FLAGS)' > $@
-
-$(BUILDDIR)/%.rel: %.c $(CCFLAGS_STAMP) | create_build_dir html_data.h
-	$(CC) -MMD $(CC_FLAGS) -o $@ -c $<
-
-$(BUILDDIR)/%.rel: %.asm $(CCFLAGS_STAMP) | create_build_dir
+$(BUILDDIR)%.rel: $(BUILDDIR)%.asm
 	${ASM} ${AFLAGS} -o $@ $<
 #	mv -f $(addprefix $(basename $^), .lst .rel .sym) .

-$(BUILDDIR)/rtlplayground.ihx: $(OBJS) $(BUILDDIR)/crtbank.rel $(BUILDDIR)/crc16.rel
-	$(CC) $(CC_FLAGS) --xram-size 49151 -Wl-bHOME=0x00000 -Wl-bBANK1=0x14000 -Wl-bBANK2=0x24000 -Wl-bBANK3=0x34000 -Wl-r -o $@ $^
+$(BUILDDIR)rtlplayground.ihx: $(BUILDDIR)crtstart.rel $(OBJS) $(BUILDDIR)crc16.rel
+	$(CC) $(CC_FLAGS) -Wl-bHOME=${BOOTLOADER_ADDRESS} -Wl-bBANK1=0x14000 -Wl-bBANK2=0x24000 -Wl-r -o $@ $^

-$(BUILDDIR)/rtlplayground.img: $(BUILDDIR)/rtlplayground.ihx
+$(BUILDDIR)rtlplayground.img: $(BUILDDIR)rtlplayground.ihx
 	objcopy --input-target=ihex -O binary $< $@

-$(BUILDDIR)/rtlplayground-$(FILENAME_EXTENSION).bin: $(BUILDDIR)/rtlplayground.img | tools
+$(BUILDDIR)rtlplayground.bin: $(BUILDDIR)rtlplayground.img
 	if [ -e $@ ]; then rm $@; fi
-	tools/output/imagebuilder -i $^ $@
-	tools/output/fileadder -a $(DEFAULT_CONFIG_LOCATION) -s $(IMAGESIZE) -d config.txt $@
-	tools/output/fileadder -a $(CONFIG_LOCATION) -s $(IMAGESIZE) -d config.txt $@
-	tools/output/fileadder -a $(HTML_LOCATION) -s $(IMAGESIZE) -z -d $(HTML_MIN) -b BANK1 $@
-	tools/output/crc_calculator -u $@
-	ln -sf $(MACHINE)/rtlplayground-$(FILENAME_EXTENSION).bin output/rtlplayground.bin
+	tools/$(BUILDDIR)imagebuilder -i $^ $@
+	tools/$(BUILDDIR)fileadder -a $(CONFIG_LOCATION) -s $(IMAGESIZE) -d config.txt $@
+	tools/$(BUILDDIR)fileadder -a $(HTML_LOCATION) -s $(IMAGESIZE) -d html -p html_data $@
+	tools/$(BUILDDIR)crc_calculator -u $@

-.PHONY: clean distclean all $(SUBDIRS) $(SUBDIRSCLEAN) create_build_dir

-# Every machine/ definition is compiled, so a machine added to machine/ is
-# covered without registering it anywhere. The machine-specific defines are
-# filtered out of $(CC_FLAGS) and supplied per iteration instead, so this also
-# works as "make machine_check MACHINE=...".
-MACHINE_DEFS := $(sort $(patsubst machine/%.c,%,$(wildcard machine/*.c)))
-MACHINE_LESS_CC_FLAGS = $(filter-out -DMACHINE_%,$(CC_FLAGS))
-
-.PHONY:
-machine_check:
-	@mkdir -p $(BUILDDIR)/tmp
-	@set -eo pipefail; \
-	for MACHINE in $(MACHINE_DEFS); \
-	do \
-	echo "Checking $${MACHINE}"; \
-	$(CC) $(MACHINE_LESS_CC_FLAGS) -DMACHINE_$${MACHINE} -DMACHINE_NAME=$${MACHINE} -MMD -o $(BUILDDIR)/tmp/machine_check -c machine/$${MACHINE}.c; \
-	$(CC) $(MACHINE_LESS_CC_FLAGS) -DMACHINE_$${MACHINE} -DMACHINE_NAME=$${MACHINE} -MMD -o $(BUILDDIR)/tmp/machine_check -c machine_init.c; \
-	done
-	@rm -rf $(BUILDDIR)/tmp
-
-include $(DEPS)
+.PHONY: clean all $(SUBDIRS)
@@ -2,15 +2,15 @@
 A Playground for Firmware development for advanced user of RTL8372/RTL8373 based 2.5GBit Switches.

 For each hardware configuration of these devices, there is usually a managed and an
-unmanaged version sold, with mostly identical hardware. The aim is to provide management
+umanaged version sold, with mostly identical hardware. The aim is to provide management
 features also for unmanaged devices with additional features such as Management VLAN,
-DHCP servers, multi-language support, IPv6 and TLS-encrypted web-pages. At present, however
+dhcp servers, multi-language support, IPv6 and TLS-encrypted web-pages. At present, however
 only the following features are provided:
 - A modern web-interface with mouse-over to display further information
 - A serial console interface to configure all features
 - IGMP to configure Multicast streaming
- Port configuration showing detailed information about own and Link-partner advertised
-  Speed settings and configuration of these settings on the local side
+- Port configuration showing detailed informtion about own and Link-partner advertised
+  Speed settins and configuration of these settings on the local side
 - Per-port configuration of frame sizes (MTUs) for Jumbo-Frame support or limiting MTUs
  for particular devices
 - EEE (Energy Efficient Ethernet) can be configured per-port. Detailed information is
@@ -25,19 +25,17 @@ only the following features are provided:
 - Firmware updates via the web
 - Installation as a firmware upgrade from the original web-interface

-<img width="1673" height="977" alt="GUI" src="doc/images/gui.png" />
+<img width="1420" height="623" alt="GUI" src="doc/images/gui.png" />

 While the firmware provides already considerable improvements over the original managed firmware,
-the firmware still lacks support for the proprietary loop prevention
-protocols as well as DHCP. Spanning Tree is available (see doc/stp.md), but is
-a simplified implementation - read that document before enabling it on a
-switch you administer over the network. If you need these features, do not install the playground on your managed
+the firmware still lacks support for STP and the proprietary loop prevention
+protocols as well as DHCP. If you need these features, do not install the playground on your managed
 devices. In any case, installation is strongly discouraged unless you can at least make
 a backup of the original flash content via a SOIC clamp such as also used for BIOS
 backups and can re-install that firmware in case something is wrong. For this no soldering
 skills are necessary.

-The firmware supports all hardware features of devices with
+The firmware supports all hardware featues of devices with
 - 4 2.5GBit ports + 2 SFP+ ports
 - 5 2.5GBIT + 1 SFP+ port
 - 8 2.5GBit + 1 SFP+ port
@@ -54,197 +52,96 @@ devices by looking at the image using e.g. Ghidra. If you want to contribute to
 design of the web-interface or get a feeling for the interface first, a standalone
 device simulator is provided, which runs entirely under Linux as a local webserver.

-## (0) Compiling Requirements
-
+## Compiling
 Install the following particular build requisites (Debian 12/13), note that Ubuntu 24.04
 still has an older version of sdcc, but you will need sdcc version 4.5 for the code to compile:
 ```
-sudo apt install make gcc sdcc xxd python-is-python3 libjson-c-dev zlib1g-dev
+sudo apt install sdcc xxd python-is-python3 libjson-c-dev
 ```

-<details>
-<summary>If using Docker (click to expand)</summary>
-
-### Prerequisites
-
-Install Docker for your platform:
-
- **Linux (Debian/Ubuntu)**: `sudo apt install docker.io` then `sudo usermod -aG docker $USER` (log out and back in)
- **Linux (other distros)**: Follow the [Docker Engine install guide](https://docs.docker.com/engine/install/)
- **Windows**: Install [Docker Desktop for Windows](https://docs.docker.com/desktop/setup/install/windows-install/)
- **macOS**: Install [Docker Desktop for Mac](https://docs.docker.com/desktop/setup/install/mac-install/)
-
-### Usage
-
-A Dockerfile is provided for a reproducible build environment:
-
+Now, building the firmware image should work:
 ```
-docker build -t rtlplayground-dev .
+$ make
+sdas8051 -plosgff crtstart.asm
+sdcc -mmcs51 -c rtlplayground.c
+sdcc -mmcs51 -c rtl837x_flash.c
+sdcc -mmcs51 -Wl-bHOME=0x100 -o rtlplayground.ihx crtstart.rel rtlplayground.rel rtl837x_flash.rel
+objcopy --input-target=ihex -O binary rtlplayground.ihx rtlplayground.img
+if [ -e rtlplayground.bin ]; then rm rtlplayground.bin; fi
+echo "0000000: 00 40" | xxd -r - rtlplayground.bin
+cat rtlplayground.img >> rtlplayground.bin 
 ```
+Note, that the image generated ends in .bin, not .img, in order to make
+IMSProg happy.

-Build the firmware (replace MACHINE with your target, e.g. `DEFAULT_8C_1SFP`):
-
-```
-docker run --rm -v $(pwd):/workspace rtlplayground-dev make MACHINE=DEFAULT_8C_1SFP
-```
-
-The resulting `.bin` file appears in `output/` on your host.
-
-Build host tools only:
-
-```
-docker run --rm -v $(pwd):/workspace rtlplayground-dev make -C tools
-```
-
-Run the web-interface simulator locally:
-
-```
-docker run --rm -p 8080:8080 -v $(pwd):/workspace rtlplayground-dev \
-  tools/output/httpd_sim /workspace/html
-```
-
-Edit `config.txt` on your host, then re-run `make` — the
-source directory is mounted into the container, so changes take effect
-immediately. To build for a different machine, pass `MACHINE=<name>`, which
-selects `machine/<name>.c` (see [Adding a new device](doc/adding-a-device.md)).
-
-</details>
-
-## (1) Compiling for direct chip flashing AND upgrading an existing RTLPlayground running device
-
-Pass the machine that matches your device, for example:
-```
-make MACHINE=DEFAULT_8C_1SFP
-```
-The name selects the board definition `machine/<name>.c`; `make` without a
-`MACHINE` value stops with an error listing what is expected. If your board is
-not in the list yet, see [Adding a new device](doc/adding-a-device.md).
-
-> [!TIP]
-> You can write configuration parameters in config.txt (see below) in order your switch to get
-> straight at the first boot, a correct IP configuration.
-
-Now, building the firmware image should work.
-
-Note, that the image generated ends in .bin, not .img, in order to make IMSProg happy.
-
-image location is stored in `RTLPlayground/output/rtlplayground_version_machine.bin`
-for example
-```
-rtlplayground-v0.1.0-12c98ba-dirty-LIANGUO_ZX_SWTGW215AS.bin
-```
-
-> [!CAUTION]
-> This image can be flashed directly to the chip OR through the firmware update/upgrade
-> interface of RTLPlayground interface
-
-## (2) Compiling for OEM running device with management options (web upgrade)
-
-Managed switches can be updated from the existing original firmware using a SPECIFIC upgrade image.
-You first need to build the firmware for direct chip flashing : See below (1)
-
-Then
-
-```
-cd installer
-make 
-```
-image location is stored in  `RTLPlayground/installer/output/rtlplayground_oem_upgrade.bin`
-
-> [!CAUTION]
-> This image must ONLY be used for original OEM firmware web interface firmware upgrade.
-> You do not need this image if you are already on RTLplayground firmware.
-> Unless you go back to the original OEM firmware, you would only flash this specific firmware
-> only once. Future upgrades of RTLPlayground will only need to follow (1)
-
-example of compilation console output
-
+Managed switches can be updated from the existing original firmware using an upgrade image.
+In the `installer`folder of the source code you will need to run `make` which will build
+an image out of `rtlplayground.bin` built in the previous step:
 ```
 RTLPlayground/installer$ make
-mkdir -p output
+mkdir -p output/
 gcc updatebuilder.c -o output/updatebuilder
 sdas8051 -plosgff -o output/crtstart.rel crtstart.asm
 sdcc -mmcs51 --code-loc 0x1000 -o output/installer.rel -c installer.c
 sdcc -mmcs51 -Wl-bHOME=0x1100 -Wl-r -o output/rtlinstaller.ihx output/crtstart.rel output/installer.rel
-./output/updatebuilder -i output/rtlinstaller.ihx -o output/rtlplayground_oem_upgrade.bin ../output/rtlplayground.bin
+cp ../output//rtlplayground.bin output/
+./output//updatebuilder -i output/rtlinstaller.ihx output/rtlplayground.bin
 Input file size: 524288
 Bytes read: 524288
 EOF
-Payload sum 1 is: 0x25100
-Payload sum 2 is: 0x25100
-Payload sum with header is: 0x264ec
-Payload sum is: 0xf8fe94
-Header checksum is: 0x5a1
+Payload sum 1 is: 0x29d10
+Payload sum 2 is: 0x29d10
+Payload sum with header is: 0x2b0fc
+Payload sum is: 0xad8a75
+Header checksum is: 0x4c3
 ```
+The resulting image can be found in `RTLPlayground/installer/output/rtlplayground.bin`
+> [!CAUTION]
+> DO NOT UPLOAD THE UPGADE IMAGE UNLESS YOU CAN MAKE A BACKUP USING A SOIC CLAMP OF THE
+> ORIGINAL FIRMWARE!

-## (3) Sandbox Usage with Ghidra (optional)
-
+## Installation
 You can play with the image using ghidra or flash real Switch Hardware. For
-ghidra see this information about [Ghidra images](doc/ghidra.md).
-
-## (4) Installation through the Web interface (software way)
-
-Managed switches (OEM firmware of RTLplayground firmware) can be upgraded via the web interface.
-Unmanaged switch cannot be flashed this way (see 5).
-
-Go to "Firmware update" tab, select the correct file.
-
-> [!IMPORTANT]
-> If your device already runs RTLPlayground, you must upload the binary file /RTLPlayground/output/rtlplayground_Version_Machine.bin
-> If your device is OEM, you must upload the binary file /RTLPlayground/installer/outputrtlplayground_oem_upgrade.bin
+ghidra see this information about [Ghidra images](ghidra.md).

 > [!CAUTION]
-> Check one more time that your device matches the machine type before flashing.
-> Be sure you have a backup of the original firmware before diving in RTLPlayground.
+> NOTE THAT WHILE THIS PROCEDURE HAS BEEN SUCCESSFULLY TESTED ON ALL DEVICES ABOVE,
+> ABSOLUTELY NO GUARANTY CAN BE GIVEN THAT YOU WILL NOT DESTROY YOUR SWITCH,
+> ANY OTHER EQUIPMENT INVOLVED OR HARM YOURSELF BY OPENING THE ELECTRONIC
+> DEVICE. OPENING THE SWITCH WILL VOID ITS WARRANTY.

-Finally, push the Upload File Button and you're done !
+You can upload the upgrade image of managed switches via the web interface of the
+original firmware just as if you were installing a firmware upgrade. However,
+this is strongly discouraged, as you may brick your device, unless you can make
+firmware backups via a SOIC clamp or soldered flash socket, first!

+For unmanaged devices, the only way to install RTLPlayground is by flashing the
+Flash memory directly.

-## (5) Flashing the ROM directly (hardware way, but also only way to rescue)
+You will need to open your switch to flash the image directly onto the flash chip,
+which is done easiest using a SOIC-8 clip (alternatively you de-solder the
+flash chip and install a SOIC adapter):
+- Disconnect power from switch
+- Attach the clip onto the flash chip
+- Connect USB of flash programmer, the power LED on the switch will light
+  up, check cabling if not. Don't panic, mixing up GND and 3.3V does not
+  seem to destroy the switch (at leasts the on I did this to).
+- Use IMSProg (flashrom should work, too) to detect the clip
+- MAKE A BACKUP OF THE EXISTING FIRMWARE!
+- then load the firmware into IMSProg
+- and program flash

-This procedure is the only way to flash unmanaged switches, if the ROM chip is large enough.
-This is also the only way to unbrick your device if something went wrong.
+Now you can connect a serial cable to the UART port found on all the
+devices, set 8N1 @ 115200 baud and power up the switch.

-> [!IMPORTANT]
-> You need a SOIC-8 clip to flash the ROM chip directly onboard.
-> Alternatively you can de-solder the flash chip and install a SOIC adapter).
-> For flashing the chip directly, you must use the binary file /RTLPlayground/output/rtlplayground_Version_Machine.bin
+The device will perform some examples and provide a minimal console, the
+documentation of which can be found in the source code rtlplayground.c`.

-> [!CAUTION]
-> As you need to open your switch case, consider that the warranty is gone.
-
- Disconnect power from switch.
- Open the switch.
- Attach the clip onto the flash chip (Red line on Pin 1, Pin 1 has a point marker).
- Connect USB of flash programmer, the power LED on the switch will light up, check cabling if not.
- Don't panic, mixing up GND and 3.3V usually does not destroy the switch.
- Use IMSProg, Flashrom, or whatever Programmer to detect the chip.
- MAKE A BACKUP (DUMP) OF THE EXISTING FIRMWARE !
- ERASE THE ROM (BLANK) !
- Load the firmware into IMSProg.
- Flash is to the ROM chip.
- Disconnect the clip from the ROM chip.
- You're done, ready for the first boot.
-
-## (6) Connecting a serial interface (optional)
-
-You can connect a serial cable to the UART port found on all the devices, set 8N1 @ 115200 baud.
-
-## (7) Power Up
-
-When you power up the switch, the device will perform some examples and provide a minimal console
-(if wired to a serial interface), the documentation of which can be found in the source code rtlplayground.c`.
-
-## (8) The web-interface
-
-The web-interface can be reached under the [default 192.168.10.247](http://192.168.10.247) unless you
-specified an IP address in the config.txt before compilation.
-
-> [!TIP]
-> The default password is `1234`.
-
-## (9) The command line
+## The web-interface
+The web-interface can be reached under the [default 192.168.10.247](http://192.168.10.247).
+The default password is `1234`.

+## The command line
 The command line is very rudimentary and mostly for testing purposes.
 The following is a boot-log with some examples:
 ```
@@ -309,6 +206,7 @@ PORT 04 1G
 <MODULE INSERTED>  Rate: 67  Encoding: 01
 Lightron Inc.   WSPXG-ES3LC-IHA 0000

+
 > stat
  CMD: stat
 Port   State   Link    TxGood          TxBad           RxGood          RxBad
@@ -326,46 +224,19 @@ Lightron Inc.   WSPXG-ES3LC-IHA 0000
  CMD: sfp
 Rate: 67  Encoding: 01
 Lightron Inc.   WSPXG-ES3LC-IHA 0000
-```
-
-## (10) Advanced configuration
-
-You can configure more deeply the switch without the need of the console mode.
-
-While in compilation part, you might write directly to config.txt file before making the binary firmware

 ```
-nano config.txt
-```
-
-If you want to modify settings after the flash is done, go to the System tab and find the Startup Configuration.
-
-<img width="1673" height="978" alt="ADVANCED SETTINGS" src="doc/images/advanced_settings.png" />
-
-```
-ip xxx.xxx.xxx.xxx      = IP address of the switch
-gw yyy.yyy.yyy.yyy      = IP address of the gateway
-netmask zzz.zzz.zzz.zzz = Network mask of the switch 
-port x name xxx         = Name xxx the port number x
-port z 1g               = Set 1g speed for port z
-igmp on/off             = Turn IGMP on or off
-session xxxx            = Web session timeout in seconds (default 200)
-```
-[To be continue]
-
 Enjoy playing!

-## (11) Other documents
-
-The following documents give further documentation on specific features of the RTL837x SoCs:
- [Adding a new device](doc/adding-a-device.md)
+## Other documents
+The following documents give further documentation on specific features of
+the RTL837x SoCs:
 - [RTL8372/3 Feature support](doc/hardware.md)
 - [CPU Port](doc/CpuPort.md)
 - [L2 learning](doc/l2.md) 
+- [CPU Port](doc/CpuPort.md)
 - [IGMP (IP-MC streaming)](doc/igmp.md)
 - [SFP+ ports](doc/sfp.md) 
 - [Trunking aka. port aggregation](doc/trunking.md)
- [LACP (802.3ad link aggregation)](doc/lacp.md)
 - [VLAN](doc/vlan.md)
- [Storm control](doc/storm_control.md)
 - [Modifications and Flash replacement](doc/mods.md)
@@ -1,479 +0,0 @@
-#pragma codeseg BANK3
-#pragma constseg BANK3
-
-#include <8051.h>
-#include <stdint.h>
-#include <stdbool.h>
-
-#include "rtl837x_sfr.h"
-#include "rtl837x_regs.h"
-#include "rtl837x_common.h"
-#include "rtl837x_flash.h"
-#include "rtl837x_pins.h"
-#include "rtl837x_phy.h"
-#include "rtl837x_port.h"
-#include "rtl837x_init.h"
-#include "machine.h"
-#include "phy.h"
-#include "boot.h"
-
-extern __code const struct machine machine;
-extern __xdata struct machine_runtime machine_detected;
-extern __xdata uint8_t sfr_data[4];
-extern volatile __xdata uint32_t ticks;
-__xdata uint32_t rtl8224_release_tick;
-extern __xdata uint8_t tx_seq;
-extern __code const uint8_t * __code const hex;
-
-
-
-void sds_config_mac(uint8_t sds, uint8_t mode) __banked
-{
-	reg_read_m(RTL837X_REG_SDS_MODES);
-	sfr_data[0] = 0;
-	sfr_data[1] = 0;
-	switch (sds) {
-	case 0:
-		sfr_mask_data(0, 0x1f, mode);
-		break;
-	case 1:
-		sfr_mask_data(0, 0xe0, mode << 5);
-		sfr_mask_data(1, 0x03, mode >> 3);
-		break;
-	case 2:
-		sfr_mask_data(1, 0xfc, 0x02 << 2);
-	}
-	if (machine_detected.isRTL8373) // Set 3rd SERDES Mode to 0x2 for RTL8224
-		sfr_mask_data(1, 0xfc, 0x02 << 2);
-	else
-		sfr_data[2] &= 0x03;
-	reg_write_m(RTL837X_REG_SDS_MODES);
-	print_string("\nRTL837X_REG_SDS_MODES: ");
-	print_reg(RTL837X_REG_SDS_MODES);
-	print_string("\n");
-}
-
-
-
-void early_boot_handle_button(void) __banked
-{
-	if (machine.reset_pin == GPIO_NA)
-		return;
-
-	gpio_input_setup(machine.reset_pin);
-
-	// Debounce after init
-	delay(100);
-	// If the button is not already held at boot, continue normally.
-	if (gpio_pin_test(machine.reset_pin))
-		return;
-
-	set_sys_led_state(SYS_LED_FAST);
-	print_string("\n[Reset button held at boot]\n");
-
-	if (gpio_pin_test(machine.reset_pin))
-		return;
-
-	const __xdata uint32_t min_hold_ticks = 10UL * SYS_TICK_HZ;
-	const __xdata uint32_t max_hold_ticks = 30UL * SYS_TICK_HZ;
-	const __xdata uint32_t blink_ticks = SYS_TICK_HZ / 10;      // 100 ms
-	const __xdata uint32_t pause_ticks = SYS_TICK_HZ / 2;       // 500 ms
-	__xdata uint32_t start_ticks = ticks;
-	__xdata uint32_t last_blink_step = start_ticks;
-	__xdata uint8_t blink_step = 0;
-
-	set_sys_led_state(SYS_LED_ON);
-
-	while (!gpio_pin_test(machine.reset_pin)) {
-		__xdata uint32_t held_ticks = ticks - start_ticks;
-
-		if (held_ticks > max_hold_ticks) {
-			print_string("[Button held >30s at boot; continuing normal boot]\n");
-			return;
-		}
-
-		// Double blink pattern while button is held:
-		// ON (100ms), OFF (100ms), ON (100ms), OFF (500ms)
-		__xdata uint32_t step_ticks = (blink_step == 3) ? pause_ticks : blink_ticks;
-		if ((ticks - last_blink_step) >= step_ticks) {
-			blink_step = (blink_step + 1) & 0x3;
-			set_sys_led_state((blink_step == 0 || blink_step == 2) ? SYS_LED_ON : SYS_LED_OFF);
-			last_blink_step = ticks;
-		}
-
-		PCON |= 1;
-	}
-
-	set_sys_led_state(SYS_LED_ON);
-
-	if ((ticks - start_ticks) >= min_hold_ticks) {
-		print_string("[Button held 10s-30s at boot; restoring default config]\n");
-		set_sys_led_state(SYS_LED_FAST);
-		flash_default_config();
-		delay(3UL * SYS_TICK_HZ);
-	}
-}
-
-
-/*
- * Configure the SerDes of the SoC for a particular mode
- * to connect to an SFP module or a PHY
- * Valid modes are SDS_10GR, SDS_QXGMII, SDS_HISGMII, SDS_HSG, SDS_SGMII and SDS_1000BX_FIBER
- * The SerDes ID may be 0 or 1 for RTL8272 and 0-2 for RTL8373
- * SDS_QXGMII is used for 10G Fiber, RTL8224 and RTL8261BE
- */
-void sds_config(uint8_t sds, uint8_t mode) __banked
-{
-	print_string("sds_config sds: "); print_byte(sds); print_string(", mode: "); print_byte(mode); write_char('\n');
-	sds_config_mac(sds, mode);
-
-	if (mode == SDS_10GR || mode == SDS_QXGMII)
-		sds_write_v(sds, 0x21, 0x10, 0x4480); // Q002110:6480
-	else
-		sds_write_v(sds, 0x21, 0x10, 0x6480); // Q002110:6480
-	sds_write_v(sds, 0x21, 0x13, 0x0400); // Q002113:0400
-	sds_write_v(sds, 0x21, 0x18, 0x6d02); // Q002118:6d02
-	sds_write_v(sds, 0x21, 0x1b, 0x424e); // Q00211b:424e
-	sds_write_v(sds, 0x21, 0x1d, 0x0002); // Q00211d:0002
-	sds_write_v(sds, 0x36, 0x1c, 0x1390); // Q00361c:1390
-	sds_write_v(sds, 0x36, 0x14, 0x003f); // Q003614:003f
-
-	uint8_t page = 0;
-	uint16_t v = 0;
-
-	switch (mode) {
-	case SDS_SGMII:
-	case SDS_1000BX_FIBER:
-		v = 0x0300;
-		page = 0x24;
-		break;
-	case SDS_HISGMII:
-	case SDS_HSG:
-		v = 0x0200;
-		page = 0x28;
-		break;
-	case SDS_10GR:
-	case SDS_QXGMII:
-		v = 0x0200;
-		page = 0x2e;
-		break;
-	case SDS_100FX:
-		v = 0x0200;
-		page = 0x26;
-		break;
-	default:
-		print_string("Error in SDS Mode\n");
-		return;
-	}
-	sds_write_v(sds, 0x36, 0x10, v); // Q003610:0200
-
-	if (page == 0x2e) {  // 10G Fiber / SDS_QXGMII
-		sds_write_v(sds, page, 0x04, 0x0080); // Q012e04:0080
-		sds_write_v(sds, page, 0x06, 0x0408); // Q012e06:0408
-		sds_write_v(sds, page, 0x07, 0x020d); // Q012e07:020d
-		sds_write_v(sds, page, 0x09, 0x0601); // Q012e09:0601
-		sds_write_v(sds, page, 0x0b, 0x222c); // Q012e0b:222c
-		sds_write_v(sds, page, 0x0c, 0xa217); // Q012e0c:a217
-		sds_write_v(sds, page, 0x0d, 0xfe40); // Q012e0d:fe40
-		sds_write_v(sds, page, 0x15, 0xf5c1); // Q012e15:f5c1
-	} else {
-		sds_write_v(sds, page, 0x04, 0x0080); // Q002804:0080
-		sds_write_v(sds, page, 0x07, 0x1201); // Q002807:1201
-		sds_write_v(sds, page, 0x09, 0x0601); // Q002809:0601
-		sds_write_v(sds, page, 0x0b, 0x232c); // Q00280b:232c
-		sds_write_v(sds, page, 0x0c, 0x9217); // Q00280c:9217
-		sds_write_v(sds, page, 0x0f, 0x5b50); // Q00280f:5b50
-		sds_write_v(sds, page, 0x15, 0xe7c1); // Q002815:e7f1 BUG !
-	}
-
-	sds_write_v(sds, page, 0x16, 0x0443); // Q002816:0443 / Q012e16:0443
-	sds_write_v(sds, page, 0x1d, 0xabb0); // Q00281d:abb0 / Q012e1d:abb0
-
-	sds_write_v(sds, 0x06, 0x12, 0x5078); // Q000612:5078
-	sds_write_v(sds, 0x07, 0x06, 0x9401); // Q000706:9401
-	sds_write_v(sds, 0x07, 0x08, 0x9401); // Q000708:9401
-	sds_write_v(sds, 0x07, 0x0a, 0x9401); // Q00070a:9401
-	sds_write_v(sds, 0x07, 0x0c, 0x9401); // Q00070c:9401
-	sds_write_v(sds, 0x1f, 0x0b, 0x0003); // Q001f0b:0003
-	sds_write_v(sds, 0x06, 0x03, 0xc45c); // Q000603:c45c
-
-	// RTL8261BE
-	if (machine.n_10g && mode == SDS_QXGMII) {
-		sds_write_v(sds, 0x06, 0x1f, 0x2100); // Q00061f:2100
-		sds_write_v(sds, 0x07, 0x11, 0x054f); // Q000711:054f
-		sds_write_v(sds, 0x20, 0x00, 0x0030); // Q002000:0030
-		sds_write_v(sds, 0x20, 0x00, 0x0010); // Q002000:0010
-		sds_write_v(sds, 0x20, 0x00, 0x0050); // Q002000:0050
-		sds_write_v(sds, 0x20, 0x00, 0x00d0); // Q002000:00d0
-		sds_write_v(sds, 0x20, 0x00, 0x0cd0); // Q002000:0cd0
-		sds_write_v(sds, 0x20, 0x00, 0x04d0); // Q002000:04d0
-		sds_write_v(sds, 0x20, 0x00, 0x04d0); // Q002000:04d0
-		sds_write_v(sds, 0x20, 0x00, 0x0cd0); // Q002000:0cd0
-		sds_write_v(sds, 0x20, 0x00, 0x00d0); // Q002000:00d0
-		sds_write_v(sds, 0x20, 0x00, 0x00d0); // Q002000:00d0
-		sds_write_v(sds, 0x20, 0x00, 0x0050); // Q002000:0050
-		sds_write_v(sds, 0x20, 0x00, 0x0010); // Q002000:0010
-		sds_write_v(sds, 0x20, 0x00, 0x0010); // Q002000:0010
-		sds_write_v(sds, 0x20, 0x00, 0x0030); // Q002000:0030
-		sds_write_v(sds, 0x20, 0x00, 0x0000); // Q002000:0000
-		sds_write_v(sds, 0x1f, 0x00, 0x000b); // Q001f00:000b
-		sds_write_v(sds, 0x1f, 0x00, 0x0000); // Q001f00:0000
-		return;
-	}
-	if (mode != SDS_QXGMII)
-		sds_write_v(sds, 0x06, 0x1f, 0x2100); // Q00061f:2100
-
-	if (mode == SDS_1000BX_FIBER) {
-		sds_write_v(sds, 0x02, 0x04, 0x0020); 	// Q000204:0020
-		sds_write_v(sds, 0x00, 0x02, 0x73d0); 	// Q000002:73d0
-		sds_write_v(sds, 0x00, 0x04, 0x074d); 	// Q000004:074d
-		sds_write_v(sds, 0x20, 0x04, 0x0000); 	// Q002000:0000
-		sds_write_v(sds, 0x1f, 0x00, 0x0000); 	// Q001f00:0000
-	}
-}
-
-
-
-
-void rtl8224_enable(void) __banked
-{
-	// Set Pin 4 low
-	reg_bit_clear(RTL837X_REG_GPIO_32_63_OUTPUT, 4);
-	// Configure Pin as output
-	reg_bit_set(RTL837X_REG_GPIO_32_63_DIRECTION, 4);
-	delay(4);
-	// Set pin 4 high
-	reg_bit_set(RTL837X_REG_GPIO_32_63_OUTPUT, 4);
-	rtl8224_release_tick = ticks;
-}
-
-
-
-void nic_setup(void) __banked
-{
-	// Enable NIC
-	// r6040:00000100 R6040-00001100
-	reg_bit_set(RTL837X_REG_HW_CONF, 0xc);
-
-	// This sets the size of the RX buffer, the filling level is in 0x7874
-	// R7848-000004ff
-	REG_SET(RTL837X_REG_NIC_RXBUFF_RX, 0x4ff);
-
-	// R7844-000007fe
-	REG_SET(RTL837X_REG_NIC_BUFFSIZE_TX, 0x7fe);
-
-	// Configure NIC RX to receive various types of packets
-	// RTL837X_REG_RX_CTRL: Set bits 24-31 to 0x4, clear bits 16/17
-	reg_read_m(RTL837X_REG_RX_CTRL);
-	sfr_mask_data(3, 0xff, 0x04);
-	sfr_mask_data(2, 0x03, 0);
-	reg_write_m(RTL837X_REG_RX_CTRL);
-
-	// Enable NIC TX (set bit 0)
-	reg_bit_set(RTL837X_REG_TX_CTRL, 0);
-
-	// Enable NIC RX (set bit 0)
-	reg_bit_set(RTL837X_REG_RX_CTRL, 0);
-
-	// Drop packets with invalid CRC
-	reg_bit_clear(RTL837X_REG_RX_CTRL, 2);
-
-	// R603c-00000200
-	// CPU-port is CPU-Tag aware (bit 9)
-	REG_SET(RTL837X_REG_CPU_TAG_AWARE_PMASK, 0x200);
-
-	// Insert CPU-tag for internally received packets (bit 0), MODE is 0, i.e. ALL packets (bits 8-9)
-	reg_read_m(RTL837X_REG_CPU_TAG);
-	sfr_mask_data(0, 1, 1);
-	sfr_mask_data(1, 3, 0);
-	reg_write_m(RTL837X_REG_CPU_TAG);
-
-	// Force MAC mode of the CPU port (port 9)
-	// r6368:00000194 R6368-00000197
-	reg_read_m(RTL837X_REG_MAC_FORCE_MODE + 9 * 4);
-	sfr_mask_data(0, 0, 3); // Set bits 0, 1: Force link
-	reg_write_m(RTL837X_REG_MAC_FORCE_MODE+ 9 * 4);
-
-	// Sequence number of TX packets
-	tx_seq = 0;
-}
-
-
-
-void rtl8373_revision(void) __banked
-{
-	reg_read_m(RTL837X_REG_CHIP_INFO);
-	sfr_mask_data(2, 0x0a, 0x0a); 	// Enable reading version
-	reg_write_m(RTL837X_REG_CHIP_INFO);
-	delay(50);
-
-	reg_read_m(RTL837X_REG_CHIP_INFO);
-	print_string("CPU revision: "); print_byte(sfr_data[2]); print_byte(sfr_data[2]); write_char('\n');
-	sfr_mask_data(2, 0x0a, 0x00); 	// Enable reading version
-	reg_write_m(RTL837X_REG_CHIP_INFO);
-}
-
-
-/*
- * The SoC manages Link-State for steering the LEDs and can set PHY-settings
- * automatically through Realtek's SMI (Simple Managagement) Interface, a
- * proprietary version of MDIO which for example allows for more PHYs on the same
- * bus.
- * Configure polling via SMI and the interface setup during boot.
- */
-void init_smi(void) __banked
-{
-	print_string("\ninit_switch called\n");
-
-	/* Set the SMI(i.e.I2C) type for PHY polling, 0b01 is 2.5/10G PHY. Disable (0b00) for the SFP-ports
-	 * which are at port 8 and additionally at port 3 for a dual SFP device
-	 */
-
-	// Default: 0x00005555
-	// Workaround for SDCC BUG 4070: SFR_DATA_U32 = 0x00005555;
-	SFR_DATA_U16_UPPER = 0x0000;
-	SFR_DATA_U16 = 0x5555;
-	if (machine.n_10g == 2) {
-		// 0x00015555, only change the bytes that differs from the default.
-		SFR_DATA_16 = 0x01;
-	} else if (machine.n_sfp == 2)
-		// 0x00005515
-		SFR_DATA_0 = 0x15;
-	reg_write(RTL837X_REG_SMI_MAC_TYPE);
-
-	// Configure polling of all PHYs by the MAC to detect link-state changes
-	// Default: 0x000000ff
-	// Workaround for SDCC BUG 4070: SFR_DATA_U32 = 0x000000ff;
-	SFR_DATA_U16_UPPER = 0x0000;
-	SFR_DATA_U16 = 0x00ff;
-	if (!machine_detected.isRTL8373) {
-		if (machine.n_sfp == 2) {
-			// 0x000000f0, only change the bytes that differs from the default.
-			SFR_DATA_0 = 0xf0;
-		} else {
-			// 0x000001f8, only change the bytes that differs from the default.
-			SFR_DATA_8 = 0x01;
-			SFR_DATA_0 = 0xf8;
-		}
-	}
-	reg_write(RTL837X_REG_SMI_PORT_POLLING);
-	// Enable MDC
-	reg_read_m(RTL837X_REG_SMI_CTRL);
-	sfr_mask_data(1, 0, 0x70); 	// Set bits 12-14 to enable MDC for SMI0-SMI2
-	reg_write_m(RTL837X_REG_SMI_CTRL);
-	delay(50);
-
-	if (!machine_detected.isRTL8373) {
-		// Change I2C addresses for SMI of the non-existent PHYs
-		// r6450:000020e6 R6450-000000e6
-		reg_read_m(RTL837X_REG_SMI_PORT6_9_ADDR);
-		sfr_mask_data(1, 0x7c, 0);
-		reg_write_m(RTL837X_REG_SMI_PORT6_9_ADDR);
-
-		// r644c:0a418820 R644c-0a400820
-		reg_read_m(RTL837X_REG_SMI_PORT0_5_ADDR);
-		sfr_mask_data(2, 0x0f, 0);
-		sfr_mask_data(1, 0x80, 0);
-		reg_write_m(RTL837X_REG_SMI_PORT0_5_ADDR);
-	}
-
-	if (machine.n_10g == 2) {
-		// Set address of second external PHY on port 8
-		REG_SET(RTL837X_REG_SMI_PORT6_9_ADDR, 0x000040e6);
-	}
-}
-
-
-
-
-void setup_i2c(void) __banked
-{
-	REG_SET(RTL837X_REG_I2C_MST_IF_CTRL, 0);
-	// Configure SFP EEPROM address (0x50) as I2C device address
-	// Configure SFP readings address (0x51) as I2C device address
-	REG_WRITE(RTL837X_REG_I2C_CTRL, 0x00, 0x1 << (I2C_MEM_ADDR_WIDTH-16),  0x50 >> 5, (0x50 << 3) & 0xff);
-
-	REG_SET(RTL837X_REG_I2C_CTRL2, 0);
-
-	// HW Control register, enable I2C depending on PIN configuration
-	reg_read_m(RTL837X_PIN_MUX_1);
-	for (uint8_t sfp = 0; sfp < machine.n_sfp; sfp++) {
-		uint8_t i2c = machine.sfp_port[sfp].i2c;
-		uint8_t scl_bus = (i2c >> RTL837X_REG_I2C_SCL_SHIFT) & RTL837X_REG_I2C_SCL_MASK;
-		uint8_t sda_bus = (i2c >> RTL837X_REG_I2C_SDA_SHIFT) & RTL837X_REG_I2C_SDA_MASK;
-		print_string("Configuring I2C for SFP idx="); print_byte(sfp); print_string(" SCL="); print_byte(scl_bus); print_string(", SDA="); print_byte(sda_bus); write_char('\n');
-		// `& RTL837X_REG_I2C_SCL_MASK` is needed to silens a compiler warning 110.
-		switch (scl_bus & RTL837X_REG_I2C_SCL_MASK) {
-			case 3:
-				// Bit 5-6 0b10 -> SCL (implies enabled SDA on bus 3)
-				sfr_mask_data(0, 0x60, 0x40);
-				break;
-			case 2: 
-				// Bit 15-16 0b01 -> SCL
-				sfr_mask_data(1, 0x80, 0x80);
-				sfr_mask_data(2, 0x01, 0x00);
-				break;
-			case 1:
-				// Bit 11-12 0b01 -> SCL
-				sfr_mask_data(1, 0x18, 0x08);
-				break;
-			case 0:
-				// Bit 7-8 0b01 -> SCL
-				sfr_mask_data(0, 0x80, 0x80);
-				sfr_mask_data(1, 0x01, 0x00);
-				break;
-		}
-
-		switch (sda_bus) {
-			case 4:
-				// Bit 29 0b0 -> SDA
-				sfr_mask_data(3, 0x20, 0x00);
-				break;
-			case 3:
-				// Bit 5-6 0b10 -> SDA (implies enabled SCL on bus 3)
-				sfr_mask_data(0, 0x60, 0x40);
-				break;
-			case 2:
-				// Bit 17-18 0b01 -> SDA
-				sfr_mask_data(2, 0x06, 0x02);
-				break;
-			case 1:
-				// Bit 13-14 0b01 -> SDA
-				sfr_mask_data(1, 0x60, 0x20);
-				break;
-			case 0:
-				// Bit 9-10 0b01 -> SDA
-				sfr_mask_data(1, 0x06, 0x02);
-				break;
-		}
-	}
-	reg_write_m(RTL837X_PIN_MUX_1);	
-}
-
-
-/* Give the switch a name carrying the tail of its MAC, so several of them on
- * one network are distinguishable out of the box. Called after the startup
- * config has been replayed and returns at once if that config already set a
- * name, so a configured switch does no work for it (suggested in review).
- *
- * Written without a loop on purpose. Locals - counters and pointers alike -
- * land in the 8051's internal-RAM overlay, and on an image with LACP and STP
- * both enabled that overlay is exhausted: a loop here makes the linker fail
- * with "Could not get 8 consecutive bytes in internal RAM for area OSEG".
- * Moving the code into its own function does not help; the overlay is shared
- * across the whole image. Hoisting the locals to xdata does not help either,
- * because itohex() is inline and brings its own frame. */
-void set_hostname_default(void) __banked
-{
-	if (hostname[0] != NUL)
-		return;
-
-	strcpy((__xdata uint8_t *)hostname, "RTLPlayground-");
-	hostname[14] = hex[uip_ethaddr.addr[3] >> 4];
-	hostname[15] = hex[uip_ethaddr.addr[3] & 0xf];
-	hostname[16] = hex[uip_ethaddr.addr[4] >> 4];
-	hostname[17] = hex[uip_ethaddr.addr[4] & 0xf];
-	hostname[18] = hex[uip_ethaddr.addr[5] >> 4];
-	hostname[19] = hex[uip_ethaddr.addr[5] & 0xf];
-	hostname[20] = NUL;
-}
@@ -1,14 +0,0 @@
-#ifndef BOOT_H
-#define BOOT_H
-
-void sds_config_mac(uint8_t sds, uint8_t mode) __banked;
-void sds_config(uint8_t sds, uint8_t mode) __banked;
-void early_boot_handle_button(void) __banked;
-void rtl8224_enable(void) __banked;
-void nic_setup(void) __banked;
-void rtl8373_revision(void) __banked;
-void init_smi(void) __banked;
-void setup_i2c(void) __banked;
-void set_hostname_default(void) __banked;
-
-#endif
@@ -1,211 +0,0 @@
-#include "cmd_parser.h"
-#include "machine.h"
-
-#pragma codeseg BANK2
-#pragma constseg BANK2
-
-// Position in the serial buffer
-__xdata uint8_t l;
-// Properties of currently edited command line in cmd_buffer[CMD_BUF_SIZE]
-__xdata uint8_t cursor;
-__xdata uint8_t cmd_line_len;
-__xdata uint8_t current_cmdline[CMD_BUF_SIZE];
-__xdata uint16_t history_editptr;
-
-
-extern __xdata uint8_t cmd_history[CMD_HISTORY_SIZE];
-extern __xdata uint16_t cmd_history_ptr;
-
-void cmd_editor_init(void) __banked
-{
-	l = sbuf_ptr; // We have printed out entered characters until l
-	cursor = 0;
-	cmd_line_len = 0;
-	cmd_available = 0;
-	history_editptr = 0xffff;
-}
-
-/*
- * Allows editing the current command line held in cmd_buffer[CMD_BUF_SIZE] by
- * identifying new characters typed or up to 4-byte escape sequences in the
- * serial buffer ring sbuf[SBUF_SIZE].
- * Upon detecting new characters or escape sequences, the cmd_buffer and the
- * representation of the command line in the terminal are updated.
- * To debug, the easist is to interpose a tty-interceptor between the physical
- * serial device and a logical one created by interceptty:
- * sudo interceptty -s 'ispeed 115200 ospeed 115200' /dev/ttyUSB0 /dev/tmpS
- * picocom -b 115200 /dev/tmpS
- */
-void cmd_edit(void) __banked
-{
-	while (l != sbuf_ptr) {
-		if (sbuf[l] >= ' ' && sbuf[l] < 127) { // A printable character, copy to command line
-			// Reserve one byte for the terminating NUL written on Enter. When the
-			// line is full, drop the character but still fall through to advance the
-			// serial-ring read pointer below; a 'continue' here would spin forever.
-			if (cmd_line_len < CMD_BUF_SIZE - 1) {
-				write_char(sbuf[l]);
-				// Shift buffer to right
-				for (uint8_t i = cmd_line_len; i > cursor; i--)
-					cmd_buffer[i] = cmd_buffer[i-1];
-				// Insert char in comand buffer
-				cmd_buffer[cursor++] = sbuf[l];
-				cmd_line_len++;
-				// Print rest of line
-				for (uint8_t i = cursor; i < cmd_line_len; i++)
-					write_char(cmd_buffer[i]);
-				// Move backwards
-				for (uint8_t i = cursor; i < cmd_line_len; i++)
-					write_char('\010'); // BS works like cursor-left
-			}
-		} else if (sbuf[l] == '\033') { // ESC-Sequence
-			// Wait until we have at least 3 characters including the ESC character in the serial buffer
-			if (((sbuf_ptr + SBUF_SIZE - l) & SBUF_MASK) < 3)
-				continue;
-			if (((sbuf_ptr > l ? sbuf_ptr - l : SBUF_SIZE + sbuf_ptr - l) >= 4)
-				   && sbuf[l] == '\033' && sbuf[(l + 1) & SBUF_MASK] == '[' && sbuf[(l + 2) & SBUF_MASK] == '3' && sbuf[(l + 3) & SBUF_MASK] == '~') { // DEL
-				if (cursor < cmd_line_len) {
-					write_char('\033'); write_char('['); write_char('1'); write_char('P'); // Delete to end of line
-					cmd_line_len--;
-					for (uint8_t i = cursor; i < cmd_line_len; i++) {
-						cmd_buffer[i] = cmd_buffer[i+1];
-						write_char(cmd_buffer[i]);
-					}
-					for (uint8_t i = cursor; i < cmd_line_len; i++)
-						write_char('\010');
-				}
-				l += 4;
-				l &= SBUF_MASK;
-				continue;
-			} else if (sbuf[l] == '\033' && sbuf[(l + 1) & SBUF_MASK] == '[' && sbuf[(l + 2) & SBUF_MASK] == 'D') { // <CURSOR-LEFT>
-				if (cursor) {
-					write_char('\010'); // BS works like cursor-left
-					cursor--;
-				}
-				l += 3;
-				l &= SBUF_MASK;
-				continue;
-			} else if (sbuf[l] == '\033' && sbuf[(l + 1) & SBUF_MASK] == '[' && sbuf[(l + 2) & SBUF_MASK] == 'C') { // <CURSOR-RIGHT>
-				if (cursor < cmd_line_len) {
-					write_char('\033'); write_char('['); write_char('C');
-					cursor++;
-				}
-				l += 3;
-				l &= SBUF_MASK;
-				continue;
-			} else if (sbuf[l] == '\033' && sbuf[(l + 1) & SBUF_MASK] == '[' && sbuf[(l + 2) & SBUF_MASK] == 'A') { // <CURSOR-UP>
-				for (uint8_t i = 0; i < cmd_line_len; i++)
-					current_cmdline[i] = cmd_buffer[i];
-				current_cmdline[cmd_line_len] = 0;
-				__xdata uint16_t p;
-				if (history_editptr == 0xffff)
-					p = (cmd_history_ptr - 2) & CMD_HISTORY_MASK;
-				else
-					p = history_editptr;
-				// Move cursor to beginning of line
-				write_char('\033'); write_char('['); itoa(cursor + 2); write_char('D');
-				cursor = 0;
-				while (cmd_history[p] && cmd_history[p] != '\n') {
-					cursor++;
-					p--;
-					p &= CMD_HISTORY_MASK;
-				}
-				history_editptr = (p - 1) & CMD_HISTORY_MASK;
-				p = (p + 1) & CMD_HISTORY_MASK;
-				if (cursor) {
-					print_string("\033[2K> "); // Clear entire line: ^[[2K and print new prompt
-					for (uint8_t i = 0; i < cursor; i++) {
-						cmd_buffer[i] = cmd_history[p];
-						write_char(cmd_buffer[i]);
-						p = (p+1) & CMD_HISTORY_MASK;
-					}
-					cmd_line_len = cursor;
-				} else {
-					print_string("\033[2C"); // Move 2 right to start of editing space
-				}
-				l += 3;
-				l &= SBUF_MASK;
-				continue;
-			} else if (sbuf[l] == '\033' && sbuf[(l + 1) & SBUF_MASK] == '[' && sbuf[(l + 2) & SBUF_MASK] == 'B') { // <CURSOR-DOWN>
-				if (history_editptr != 0xffff) {
-					__xdata uint16_t p = (history_editptr + 2) & CMD_HISTORY_MASK;
-					// Move cursor to beginning of line
-					write_char('\033'); write_char('['); itoa(cursor + 2); write_char('D');
-					print_string("\033[2K> "); // Clear entire line: ^[[2K and print new prompt
-					uint8_t i = 0;
-					while (cmd_history[p] && cmd_history[p] != '\n') {
-						p = (p + 1) & CMD_HISTORY_MASK;
-					}
-					p = (p + 1) & CMD_HISTORY_MASK;
-					while (cmd_history[p] && cmd_history[p] != '\n') {
-						cmd_buffer[i] = cmd_history[p];
-						write_char(cmd_buffer[i++]);
-						p = (p + 1) & CMD_HISTORY_MASK;
-					}
-					history_editptr = (p - 1) & CMD_HISTORY_MASK;
-					if (!i) {
-						if (current_cmdline[i]) {
-							while (current_cmdline[i]) {
-								cmd_buffer[i] = current_cmdline[i];
-								write_char(cmd_buffer[i++]);
-							}
-						} else {
-							write_char('\033'); write_char('['); write_char('C');
-						}
-						history_editptr = 0xffff;
-						// Move cursor right
-					}
-					cmd_line_len = i;
-					cursor = 0;
-					// Move cursor again to beginning of line
-					write_char('\033'); write_char('['); itoa(i); write_char('D');
-				} else {
-					// If we are at the last entry of the history, just move the cursor to the end of the line
-					if (cursor < cmd_line_len) {
-						write_char('\033'); write_char('['); itoa(cmd_line_len - cursor); write_char('C');
-					}
-					cursor = cmd_line_len;
-				}
-				l += 3;
-				l &= SBUF_MASK;
-				continue;
-			} else { // An unknown or not yet complete Escape sequence: wait
-				continue;
-			}
-		} else if (sbuf[l] == 127 || sbuf[l] == 8) {  // Backspace DEL or BS/^H
-			if (cursor > 0) {
-				write_char('\010');
-				for (uint8_t i = cursor; i < cmd_line_len; i++)
-					write_char(cmd_buffer[i]);
-				write_char(' '); // Overwrite end of line
-				// Move backwards n steps:
-				for (uint8_t i = cursor; i <= cmd_line_len; i++)
-					write_char('\010');
-				cursor--;
-				for (uint8_t i = cursor; i <= cmd_line_len; i++)
-					cmd_buffer[i] = cmd_buffer[i+1];
-				cmd_line_len--;
-			}
-		}
-		// If the command buffer is currently in use, we cannot copy to it
-		if (cmd_available)
-			break;
-		// Check whether return was pressed:
-		if (sbuf[l] == '\n' || sbuf[l] == '\r') {
-			write_char('\n');
-			cmd_buffer[cmd_line_len] = NUL;
-//			write_char('>'); print_string_x(cmd_buffer); write_char('<');
-			// If there is a command we print the prompt after execution
-			// otherwise immediately because there is nothing to execute
-			if (cmd_line_len)
-				cmd_available = 1;
-			else
-				print_cmd_prompt();
-			cursor = 0;
-			cmd_line_len = 0;
-			history_editptr = 0xffff;
-		}
-		l++;
-		l &= SBUF_MASK;
-	}
-}
@@ -1,9 +0,0 @@
-#ifndef _CMD_EDITOR_H_
-#define _CMD_EDITOR_H_
-
-#include <stdint.h>
-
-void cmd_editor_init(void) __banked;
-void cmd_edit(void) __banked;
-
-#endif
@@ -5,44 +5,11 @@

 #include "rtl837x_common.h"

-extern __xdata uint8_t cmd_buffer[CMD_BUF_SIZE];
-extern __bit __at(0x03) cmd_available;
-extern __xdata uint8_t err_status;
+extern __xdata uint8_t cmd_buffer[SBUF_SIZE];
+extern __xdata uint8_t cmd_available;

-/* Health instrumentation, built with HEALTH=1. Without it the hooks below
- * compile to nothing and the "health" command does not exist. */
-#ifdef HEALTH
-/* Phase ids, in main-loop order */
-#define HEALTH_PH_LINK	0
-#define HEALTH_PH_SFP	1
-#define HEALTH_PH_RX	2
-#define HEALTH_PH_TX	3
-#define HEALTH_PH_STP	4
-#define HEALTH_PH_CMD	5
-#define HEALTH_PHASES	6
-#define HEALTH_LLDP     7
-
-extern __xdata uint16_t health_rx_frames;
-#define health_rx_frame()	health_rx_frames++
-
-void health_loop_start(void) __banked;	/* once per idle() pass, resets the phase baseline */
-void health_phase(uint8_t id) __banked;	/* after each phase; accounts ticks since last checkpoint */
-void health_stack_paint(void) __banked;	/* paint the unused stack area once at boot */
-void health_show(void) __banked;	/* "health" CLI dump */
-#else
-#define health_rx_frame()
-#define health_loop_start()
-#define health_phase(id)
-#define health_stack_paint()
-#endif
-
-void cmd_tokenize(void) __banked;
+uint8_t cmd_tokenize(void) __banked;
 void cmd_parser(void) __banked;
 void execute_config(void) __banked;
-void execute_commands(__xdata uint8_t *p) __banked;
-void print_ip(__xdata uint8_t *ptr) __banked;
-void print_mac(__xdata uint8_t *ptr) __banked;
 void print_sw_version(void) __banked;
-void clear_command_history(void) __banked;
-
 #endif
@@ -3,8 +3,6 @@
 ;
 	.globl 	_crc_value
 	.globl 	_crc16
-	.globl 	_crc16_bank1
-	.globl 	__sdcc_banked_ret
 	.equ	BANK, 0x96
 ;	.equ	DPS, 0x86
 ; Variable in XMEM holding current CRC16 value, being updated
@@ -20,7 +18,7 @@ _crc_value::
 	.area HOME    (CODE)
 	.area CSEG    (CODE)
 ;	.area BANK1   (CODE)
-_crc16_bank1:
+_crc16:
 	mov	BANK, #1
 	push	dph
 	push	dpl
@@ -54,10 +52,6 @@ _crc16_bank1:

 	.area BANK1   (CODE)

-_crc16:
-	lcall	_crc16_bank1
-	ljmp	__sdcc_banked_ret
-
 crc16_table_l:
 	.byte #0x00, #0xc1, #0x81, #0x40, #0x01, #0xc0, #0x80, #0x41
 	.byte #0x01, #0xc0, #0x80, #0x41, #0x00, #0xc1, #0x81, #0x40
@@ -1,29 +0,0 @@
-	.area HOME    (CODE)
-	.area GSINIT0 (CODE)
-	.area GSINIT1 (CODE)
-	.area GSINIT2 (CODE)
-	.area GSINIT3 (CODE)
-	.area GSINIT4 (CODE)
-	.area GSINIT5 (CODE)
-	.area GSINIT  (CODE)
-	.area GSFINAL (CODE)
-	.area CSEG    (CODE)
-
-
-	.area HOME    (CODE)
-
-__sdcc_banked_call::
-	push	_PSBANK
-	xch	a,r0
-	push	a
-	mov	a,r1
-	push	a
-	mov	a,r2
-	anl	a,#0x1f
-	mov	_PSBANK, a
-	xch	a, r0
-	ret
-
-__sdcc_banked_ret::
-	pop	_PSBANK
-	ret
@@ -0,0 +1,57 @@
+	.globl __start__stack
+;--------------------------------------------------------
+; Stack segment in internal ram
+;--------------------------------------------------------
+	.area	SSEG	(DATA)
+__start__stack:
+	.ds	1
+
+ 	.area VECTOR    (CODE)
+	.globl __interrupt_vect
+__interrupt_vect:
+ 	ljmp	__sdcc_gsinit_startup
+ 	ljmp	_isr_ext0	; 0x03
+	.ds     5
+	ljmp	_isr_timer0	; 0x0b
+	.ds     5
+	ljmp	_isr_ext1	; 0x13
+	.ds     5
+	reti			; 0x1b TIMER 1 IRQ
+	.ds     7
+ 	ljmp    _isr_serial	; 0x23
+	.ds     5
+	ljmp	_isr_timer2	; 0x2b TIMER 2 IRQ
+	.ds     5
+	reti			; 0x33 NOT used by DW8051
+	.ds     7
+	reti			; 0x3b Serial port 1 RX/TX IRQ
+	.ds     7
+ 	ljmp    _isr_ext2	; 0x43
+	.ds     5
+ 	ljmp    _isr_ext3	; 0x4b
+
+	.globl __start__stack
+
+	.area GSINIT0 (CODE)
+
+__sdcc_gsinit_startup::
+        mov     sp,#__start__stack - 1
+
+	.area GSFINAL (CODE)
+        ljmp	_bootloader
+
+__sdcc_banked_call::
+	push	_PSBANK
+	xch	a,r0
+	push	a
+	mov	a,r1
+	push	a
+	mov	a,r2
+	anl	a,#0x1f
+	mov	_PSBANK, a
+	xch	a, r0
+	ret
+
+__sdcc_banked_ret::
+	pop	_PSBANK
+	ret
@@ -12,6 +12,7 @@
 #include "uip.h"
 #include "uip/uip.h"

+extern __code struct uip_eth_addr uip_ethaddr;
 __xdata struct dhcp_state dhcp_state;
 __xdata uip_ipaddr_t server;

@@ -41,7 +42,6 @@ __xdata uip_ipaddr_t server;
 #define DHCP_REBIND_LEN		4
 #define DHCP_CLIENT_ID		61
 #define DHCP_CLIENT_ID_LEN	7
-#define DHCP_HOSTNAME		12
 #define DHCP_REQUEST_IP		50
 #define DHCP_REQUEST_IP_LEN	4
 #define DHCP_PARAMS		55
@@ -50,7 +50,7 @@ __xdata uip_ipaddr_t server;
 #define DHCP_PARAM_DNS		6
 #define DHCP_END		255

-#pragma codeseg BANK3
+#pragma codeseg BANK2
 #pragma constseg BANK2

 struct dhcp_pkt {
@@ -72,13 +72,18 @@ struct dhcp_pkt {
 	uint8_t cookie[4];
 };

+/*
+#define DHCP_P ((__xdata struct dhcp_pkt *)&uip_buf[RTL_TAG_SIZE + VLAN_TAG_SIZE])
+#define DHCP_OPT ((__xdata uint8_t *)&uip_buf[RTL_TAG_SIZE + VLAN_TAG_SIZE + sizeof (struct dhcp_pkt)])
+*/
+
 #define DHCP_P ((__xdata struct dhcp_pkt *)uip_appdata)
 #define DHCP_OPT ((__xdata uint8_t *)(uip_appdata) + sizeof (struct dhcp_pkt))

 __xdata uint32_t long_value;


-void dhcp_print_ip(__xdata uint8_t *a)
+void dhcp_print_ip(uint8_t *a)
 {
 	itoa(a[0]); write_char('.');
 	itoa(a[1]); write_char('.');
@@ -94,12 +99,12 @@ void dhcp_prepare_request(void)
 	DHCP_P->hw_len = 6;
 	DHCP_P->hops = 0;

-	DHCP_P->tid = dhcp_state.transaction_id;
+	DHCP_P->tid = HTONS(dhcp_state.transaction_id);
 	DHCP_P->delay = HTONS(0);
 	DHCP_P->flags = 0;
 	// Clear fields client_ip to bootp_file
 	memset(DHCP_P->client_ip, 0, 224);
-	memcpy(DHCP_P->client_addr, uip_ethaddr.addr, 6);
+	memcpyc(DHCP_P->client_addr, uip_ethaddr.addr, 6);
 	DHCP_P->cookie[0] = 0x63;
 	DHCP_P->cookie[1] = 0x82;
 	DHCP_P->cookie[2] = 0x53;
@@ -112,25 +117,11 @@ void dhcp_addopt_client_id(void)
 	DHCP_OPT[dhcp_state.opt_ptr++] = DHCP_CLIENT_ID;
 	DHCP_OPT[dhcp_state.opt_ptr++] = DHCP_CLIENT_ID_LEN;
 	DHCP_OPT[dhcp_state.opt_ptr++] = DHCP_HW_TYPE_ETH;
-	memcpy(&DHCP_OPT[dhcp_state.opt_ptr], uip_ethaddr.addr, 6);
+	memcpyc(&DHCP_OPT[dhcp_state.opt_ptr], uip_ethaddr.addr, 6);
 	dhcp_state.opt_ptr += 6;
 }


-void dhcp_addopt_hostname(void)
-{
-	uint8_t len = 0;
-	while (hostname[len])
-		len++;
-	if (!len)
-		return;
-	DHCP_OPT[dhcp_state.opt_ptr++] = DHCP_HOSTNAME;
-	DHCP_OPT[dhcp_state.opt_ptr++] = len;
-	memcpy(&DHCP_OPT[dhcp_state.opt_ptr], hostname, len);
-	dhcp_state.opt_ptr += len;
-}
-
-
 void dhcp_addopt_request_ip(void)
 {
 	DHCP_OPT[dhcp_state.opt_ptr++] = DHCP_REQUEST_IP;
@@ -139,6 +130,7 @@ void dhcp_addopt_request_ip(void)
 	DHCP_OPT[dhcp_state.opt_ptr++] = dhcp_state.current_ip[1];
 	DHCP_OPT[dhcp_state.opt_ptr++] = dhcp_state.current_ip[2];
 	DHCP_OPT[dhcp_state.opt_ptr++] = dhcp_state.current_ip[3];
+	memcpyc(&DHCP_OPT[dhcp_state.opt_ptr], uip_ethaddr.addr, 4);
 }


@@ -150,11 +142,13 @@ void dhcp_addopt_server_id(void)
 	DHCP_OPT[dhcp_state.opt_ptr++] = dhcp_state.server[1];
 	DHCP_OPT[dhcp_state.opt_ptr++] = dhcp_state.server[2];
 	DHCP_OPT[dhcp_state.opt_ptr++] = dhcp_state.server[3];
+	memcpyc(&DHCP_OPT[dhcp_state.opt_ptr], uip_ethaddr.addr, 4);
 }


 void dhcp_send_discover(void)
 {
+	print_string("dhcp_send_discover called\n");
 	dhcp_prepare_request();

 	dhcp_state.opt_ptr = 0;
@@ -164,7 +158,6 @@ void dhcp_send_discover(void)

 	dhcp_addopt_client_id();
 	dhcp_addopt_request_ip();
-	dhcp_addopt_hostname();

 	DHCP_OPT[dhcp_state.opt_ptr++] = DHCP_PARAMS;
 	DHCP_OPT[dhcp_state.opt_ptr++] = 3;
@@ -190,6 +183,7 @@ void dhcp_send_discover(void)

 void dhcp_send_request(void)
 {
+	print_string("dhcp_send_request called\n");
 	dhcp_prepare_request();

 	dhcp_state.opt_ptr = 0;
@@ -200,7 +194,6 @@ void dhcp_send_request(void)
 	dhcp_addopt_client_id();
 	dhcp_addopt_request_ip();
 	dhcp_addopt_server_id();
-	dhcp_addopt_hostname();

 	DHCP_OPT[dhcp_state.opt_ptr++] = DHCP_PARAMS;
 	DHCP_OPT[dhcp_state.opt_ptr++] = 3;
@@ -224,25 +217,23 @@ void dhcp_send_request(void)
 }


-void ip_opt(__xdata uint8_t * ip)
+void ip_opt(uint8_t * __xdata ip)
 {
 	dhcp_state.opt_ptr++;
 	uint8_t len = DHCP_OPT[dhcp_state.opt_ptr++];
-	if (len >= 4)
-		memcpy(ip, &DHCP_OPT[dhcp_state.opt_ptr], 4);
+	*ip++ = DHCP_OPT[dhcp_state.opt_ptr++];
+	*ip++ = DHCP_OPT[dhcp_state.opt_ptr++];
+	*ip++ = DHCP_OPT[dhcp_state.opt_ptr++];
+	*ip++ = DHCP_OPT[dhcp_state.opt_ptr++];
 	 // There may be more than one IP option, such as 2 DNS servers advertised
-	dhcp_state.opt_ptr += len;
+	dhcp_state.opt_ptr += len - 4;
 }


-uint8_t long_opt(void)
+void long_opt(void)
 {
 	dhcp_state.opt_ptr++;
-	uint8_t len = DHCP_OPT[dhcp_state.opt_ptr++];
-	if (len < 4) {
-		dhcp_state.opt_ptr += len;
-		return 0;
-	}
+	dhcp_state.opt_ptr++;
 	long_value =  DHCP_OPT[dhcp_state.opt_ptr++];
 	long_value <<= 8;
 	long_value |= DHCP_OPT[dhcp_state.opt_ptr++];
@@ -250,8 +241,6 @@ uint8_t long_opt(void)
 	long_value |= DHCP_OPT[dhcp_state.opt_ptr++];
 	long_value <<= 8;
 	long_value |= DHCP_OPT[dhcp_state.opt_ptr++];
-	dhcp_state.opt_ptr += len - 4;
-	return 1;
 }


@@ -275,16 +264,16 @@ void parse_opts(void)
 			ip_opt(&dhcp_state.broadcast[0]);
 			break;
 		case DHCP_LEASE:
-			if (long_opt())
-				dhcp_state.lease = long_value;
+			long_opt();
+			dhcp_state.lease = long_value;
 			break;
 		case DHCP_REBIND:
-			if (long_opt())
-				dhcp_state.rebind = long_value;
+			long_opt();
+			dhcp_state.rebind = long_value;
 			break;
 		case DHCP_RENEWAL:
-			if (long_opt())
-				dhcp_state.renewal = long_value;
+			long_opt();
+			dhcp_state.renewal = long_value;
 			break;
 		case DHCP_END:
 			break;
@@ -300,7 +289,7 @@ void parse_opts(void)

 void parse_dhcp(void)
 {
-	if (DHCP_P->tid != dhcp_state.transaction_id)
+	if (!DHCP_P->tid == HTONS(dhcp_state.transaction_id))
 		return;
 	if (DHCP_P->cookie[0] != 0x63 || DHCP_P->cookie[1] != 0x82 || DHCP_P->cookie[2] != 0x53 || DHCP_P->cookie[3] != 0x63)
 		return;
@@ -332,18 +321,6 @@ void parse_dhcp(void)
 		uip_ipaddr(&uip_hostaddr, dhcp_state.current_ip[0], dhcp_state.current_ip[1], dhcp_state.current_ip[2], dhcp_state.current_ip[3]);
 		uip_ipaddr(&uip_draddr, dhcp_state.router[0], dhcp_state.router[1], dhcp_state.router[2], dhcp_state.router[3]);
 		uip_ipaddr(&uip_netmask, dhcp_state.subnet[0], dhcp_state.subnet[1], dhcp_state.subnet[2], dhcp_state.subnet[3]);
-		/* T1 is optional. Without it the renewal time stays zero, which
-		 * makes dhcp_timer zero, and the callback then sends a REQUEST on
-		 * every pass through LEASING: client and server trade REQUEST and
-		 * ACK as fast as the round trip allows. RFC 2131 has the client
-		 * renew at half the lease when the server does not say, and if
-		 * there is no lease either, pick something rather than zero. Only
-		 * filled in when absent, so a server that asks for a short renewal
-		 * still gets it. */
-		if (!dhcp_state.renewal)
-			dhcp_state.renewal = dhcp_state.lease / 2;
-		if (!dhcp_state.renewal)
-			dhcp_state.renewal = 60;
 		dhcp_state.state = DHCP_LEASING;
 		dhcp_state.ticks = SYS_TICK_HZ;
 		dhcp_state.dhcp_timer = dhcp_state.renewal > 0xffff ? 0xffff : dhcp_state.renewal;
@@ -353,12 +330,6 @@ void parse_dhcp(void)

 void dhcp_start(void) __banked
 {
-	/* Starting twice would leave the first socket bound: uip_udp_new() takes
-	 * the next free slot while the old one keeps port 68, and dhcp_callback()
-	 * matches on that port rather than on the connection, so every leftover
-	 * runs the state machine too and the timers count down once per socket. */
-	if (dhcp_state.state != DHCP_OFF)
-		dhcp_stop();
 	uip_ipaddr(server, 255,255,255,255);
 	dhcp_state.conn = uip_udp_new(&server, HTONS(DHCPC_SERVER_PORT));
 	dhcp_state.current_ip[0] = dhcp_state.current_ip[1] = dhcp_state.current_ip[2] = dhcp_state.current_ip[3] = 0;
@@ -369,27 +340,22 @@ void dhcp_start(void) __banked
 		return;
 	}
 	get_random_32();
-	// Workaround SDCC bug 4070: dhcp_state.transaction_id = SFR_DATA_U32;
-	__xdata uint8_t * tid = &dhcp_state.transaction_id;
-	*tid++ = SFR_DATA_24;
-	*tid++ = SFR_DATA_16;
-	*tid++ = SFR_DATA_8;
-	*tid = SFR_DATA_0;
+	dhcp_state.transaction_id = SFR_DATA_U32;
 	dhcp_state.state = DHCP_START;
+	print_string("dhcp_start done\n");
 }


 void dhcp_stop(void) __banked
 {
+	print_string("dhcp_stop called\n");
 	uip_udp_remove(dhcp_state.conn);
 	dhcp_state.state = DHCP_OFF;
 }


-void dhcp_callback(uint16_t lport) __banked
+void dhcp_callback(void) __banked
 {
-	if (lport != HTONS(DHCPC_CLIENT_PORT)) // Is this call for us? If not, ignore it
-		return;
 	if (!dhcp_state.state)
 		return;
 	if (uip_closed()) {
@@ -16,7 +16,7 @@
 void dhcp_start(void) __banked;
 void dhcp_stop(void) __banked;
 // void dhcp_periodic(void) __banked;
-void dhcp_callback(uint16_t lport) __banked;
+void dhcp_callback(void) __banked;


 struct dhcp_state {
@@ -35,9 +35,14 @@ struct dhcp_state {
 	uint32_t rebind;
 	uint32_t renewal;

-	__xdata struct uip_udp_conn *conn;
+	struct uip_udp_conn *conn;
 };

 typedef struct dhcp_state uip_udp_appstate_t;

+/* Finally we define the application function to be called by uIP. */
+#ifndef UIP_UDP_APPCALL
+#define UIP_UDP_APPCALL dhcp_callback
+#endif /* UIP_APPCALL */
+
 #endif
@@ -1,238 +0,0 @@
-/*
- * DNS resolver for the RTL837x platform
- * This code is in the Public Domain
- */
-
-#include <stdint.h>
-#include "rtl837x_common.h"
-#include "cmd_parser.h"
-#include "uip/uip.h"
-#include "dhcp.h"
-#include "dns.h"
-
-#pragma codeseg BANK3
-#pragma constseg BANK3
-
-#define DNS_PORT	53
-#define DNS_TRIES	6
-#define DNS_TIMEOUT	(2 * SYS_TICK_HZ)
-
-extern __xdata struct dhcp_state dhcp_state;
-extern volatile __xdata uint32_t ticks;
-
-__xdata struct dns_state dns_state;
-__xdata uip_ipaddr_t dns_ip;
-uint8_t * __xdata dns_cand[3];
-
-
-static uint8_t dns_used(__xdata uint8_t *a) __reentrant
-{
-	return a[0] | a[1] | a[2] | a[3];
-}
-
-
-static uint8_t dns_name_is_ip(void) __reentrant
-{
-	__xdata char *s = dns_state.name;
-	uint8_t i, n;
-	uint16_t v;
-
-	for (i = 0; i < 4; i++) {
-		v = 0;
-		n = 0;
-		while (*s >= '0' && *s <= '9') {
-			v = v * 10 + (*s++ - '0');
-			if (++n > 3 || v > 255)
-				return 0;
-		}
-		if (!n)
-			return 0;
-		dns_state.addr[i] = v;
-		if (i < 3 && *s++ != '.')
-			return 0;
-	}
-	return !*s;
-}
-
-
-static void dns_next(void) __reentrant
-{
-	uint8_t k = 0;
-
-	if (dns_state.conn) {
-		uip_udp_remove(dns_state.conn);
-		dns_state.conn = 0;
-	}
-	if (dns_used(dns_state.server[0]))
-		dns_cand[k++] = dns_state.server[0];
-	if (dns_used(dns_state.server[1]))
-		dns_cand[k++] = dns_state.server[1];
-	if (dns_used(dhcp_state.dns))
-		dns_cand[k++] = dhcp_state.dns;
-	if (!k || dns_state.tries >= DNS_TRIES) {
-		dns_state.status = DNS_FAILED;
-		if (dns_state.verbose)
-			print_string(k ? "DNS: no answer\n" : "DNS: no server\n");
-		return;
-	}
-	k = dns_state.tries % k;
-	uip_ipaddr(dns_ip, dns_cand[k][0], dns_cand[k][1], dns_cand[k][2], dns_cand[k][3]);
-	dns_state.conn = uip_udp_new(&dns_ip, HTONS(DNS_PORT));
-	if (!dns_state.conn) {
-		dns_state.status = DNS_FAILED;
-		print_string("DNS: no free UDP connection\n");
-		return;
-	}
-	dns_state.send = 1;
-}
-
-
-static void dns_query(void) __reentrant
-{
-	__xdata uint8_t *p = (__xdata uint8_t *)uip_appdata;
-	__xdata char *n = dns_state.name;
-	__xdata uint8_t *label;
-	uint16_t len = 12;
-
-	dns_state.id++;
-	p[0] = dns_state.id >> 8;
-	p[1] = dns_state.id;
-	p[2] = 0x01;
-	p[3] = 0x00;
-	p[4] = 0;
-	p[5] = 1;
-	p[6] = p[7] = p[8] = p[9] = p[10] = p[11] = 0;
-	while (*n) {
-		label = p + len++;
-		*label = 0;
-		while (*n && *n != '.') {
-			p[len++] = *n++;
-			(*label)++;
-		}
-		if (*n)
-			n++;
-	}
-	p[len++] = 0;
-	p[len++] = 0;
-	p[len++] = 1;
-	p[len++] = 0;
-	p[len++] = 1;
-	uip_udp_send(len);
-}
-
-
-static uint16_t dns_skip_name(__xdata uint8_t *p, uint16_t i, uint16_t len) __reentrant
-{
-	while (i < len) {
-		if (!p[i])
-			return i + 1;
-		if ((p[i] & 0xc0) == 0xc0)
-			return i + 2;
-		i += p[i] + 1;
-	}
-	return len;
-}
-
-
-static void dns_answer(void) __reentrant
-{
-	__xdata uint8_t *p = (__xdata uint8_t *)uip_appdata;
-	uint16_t len = uip_datalen();
-	uint16_t i, an;
-
-	if (dns_state.status != DNS_PENDING || len < 12 || !(p[2] & 0x80)
-	    || p[0] != (uint8_t)(dns_state.id >> 8) || p[1] != (uint8_t)dns_state.id)
-		return;
-	an = ((uint16_t)p[6] << 8) | p[7];
-	i = dns_skip_name(p, 12, len) + 4;
-	while (!(p[3] & 0x0f) && an-- && i + 10 <= len) {
-		i = dns_skip_name(p, i, len);
-		if (i + 10 > len)
-			break;
-		if (!p[i] && p[i + 1] == 1 && !p[i + 8] && p[i + 9] == 4 && i + 14 <= len) {
-			memcpy(dns_state.addr, p + i + 10, 4);
-			dns_state.status = DNS_DONE;
-			uip_udp_remove(dns_state.conn);
-			dns_state.conn = 0;
-			if (dns_state.verbose) {
-				print_string("DNS: ");
-				print_string_x(dns_state.name);
-				print_string(" is ");
-				print_ip(dns_state.addr);
-				write_char('\n');
-			}
-			return;
-		}
-		i += 10 + (((uint16_t)p[i + 8] << 8) | p[i + 9]);
-	}
-	dns_state.tries = DNS_TRIES;
-	dns_next();
-}
-
-
-void dns_init(void) __banked
-{
-	memset(dns_state.server, 0, sizeof(dns_state.server));
-	dns_state.name[0] = 0;
-	dns_state.status = DNS_IDLE;
-	dns_state.conn = 0;
-}
-
-
-void dns_lookup(void) __banked
-{
-	if (dns_name_is_ip()) {
-		dns_state.status = DNS_DONE;
-		return;
-	}
-	dns_state.tries = 0;
-	dns_state.status = DNS_PENDING;
-	dns_next();
-}
-
-
-void dns_show(void) __banked
-{
-	print_string("DNS servers ");
-	print_ip(dns_state.server[0]);
-	write_char(' ');
-	print_ip(dns_state.server[1]);
-	print_string(", from DHCP ");
-	print_ip(dhcp_state.dns);
-	write_char('\n');
-	if (!dns_state.name[0])
-		return;
-	print_string("Last lookup ");
-	print_string_x(dns_state.name);
-	print_string(": ");
-	if (dns_state.status == DNS_DONE)
-		print_ip(dns_state.addr);
-	else if (dns_state.status == DNS_PENDING)
-		print_string("pending");
-	else
-		print_string("failed");
-	write_char('\n');
-}
-
-
-void dns_callback(uint16_t lport) __banked __reentrant
-{
-	if (!dns_state.conn || lport != dns_state.conn->lport)
-		return;
-	if (uip_newdata()) {
-		dns_answer();
-		return;
-	}
-	if (dns_state.status != DNS_PENDING)
-		return;
-	if (dns_state.send) {
-		dns_state.send = 0;
-		dns_state.sent = ticks;
-		dns_query();
-		return;
-	}
-	if (ticks - dns_state.sent >= DNS_TIMEOUT) {
-		dns_state.tries++;
-		dns_next();
-	}
-}
@@ -1,36 +0,0 @@
-#ifndef _DNS_H_
-#define _DNS_H_
-
-#include <stdint.h>
-
-#define DNS_NAME_LEN	48
-
-#define DNS_IDLE	0
-#define DNS_PENDING	1
-#define DNS_DONE	2
-#define DNS_FAILED	3
-
-struct uip_udp_conn;
-
-struct dns_state {
-	uint8_t server[2][4];	/* configured servers, 0.0.0.0 = unused */
-	char name[DNS_NAME_LEN];	/* name of the current or last lookup */
-	uint8_t addr[4];	/* address found by the last lookup */
-	uint8_t status;		/* DNS_* */
-	uint8_t verbose;	/* print the result of the lookup */
-	uint8_t tries;		/* queries sent for the current lookup */
-	uint8_t send;		/* a query is due on the connection */
-	uint16_t id;
-	uint32_t sent;		/* ticks when the last query went out */
-	struct uip_udp_conn *conn;
-};
-
-extern __xdata struct dns_state dns_state;
-
-void dns_init(void) __banked;
-void dns_lookup(void) __banked;
-void dns_show(void) __banked;
-void dns_callback(uint16_t lport) __banked __reentrant;
-void dns_parse(void) __banked __reentrant;
-
-#endif
@@ -1,63 +0,0 @@
-/*
- * Command line interface of the DNS resolver for the RTL837x platform
- * This code is in the Public Domain
- */
-
-#include <stdint.h>
-#include "rtl837x_common.h"
-#include "cmd_parser.h"
-#include "dns.h"
-
-#pragma codeseg BANK2
-#pragma constseg BANK2
-
-extern __xdata uint8_t cmd_buffer[CMD_BUF_SIZE];
-extern __xdata uint8_t cmd_words_len;
-extern __xdata uint8_t cmd_words_b[15];
-extern __xdata uint8_t ip[4];
-uint8_t cmd_compare(uint8_t start, __code const uint8_t * cmd);
-uint8_t parse_ip(uint8_t idx);
-
-
-void dns_parse(void) __banked __reentrant
-{
-	__xdata uint8_t *s;
-	uint8_t n;
-
-	if (cmd_words_len < 2) {
-		dns_show();
-		return;
-	}
-	if (cmd_compare(1, "server") && cmd_words_len >= 3 && parse_ip(cmd_words_b[2])) {
-		memcpy(dns_state.server[0], ip, 4);
-		memset(dns_state.server[1], 0, 4);
-		if (cmd_words_len >= 4) {
-			if (!parse_ip(cmd_words_b[3]))
-				goto err;
-			memcpy(dns_state.server[1], ip, 4);
-		}
-		return;
-	}
-	if (cmd_compare(1, "lookup") && cmd_words_len >= 3) {
-		if (dns_state.status == DNS_PENDING) {
-			print_string("DNS: a lookup is already running\n");
-			return;
-		}
-		s = &cmd_buffer[cmd_words_b[2]];
-		for (n = 0; s[n] && s[n] != ' '; n++) {
-			if (n == DNS_NAME_LEN - 1)
-				goto err;
-			dns_state.name[n] = s[n];
-		}
-		dns_state.name[n] = 0;
-		dns_state.verbose = 1;
-		dns_lookup();
-		if (dns_state.status == DNS_DONE) {
-			print_ip(dns_state.addr);
-			write_char('\n');
-		}
-		return;
-	}
-err:
-	print_string("Error: dns [server <ip> [<ip>]|lookup <name>]\n");
-}
@@ -64,33 +64,3 @@ Writing 0x1 to register 0x7850 will transmit the frame. The Ethernet frame
 checksum and the TCP checksum are automatically calculated (offloaded) by the
 ASIC before transmitting on the wire.

-
-## The RTL tag words
-
-The frame header uses the Realtek Remote Control Protocol (RRCP) format or
-the like.
-
-The `flags` word:
-
-```
-bit15 EFID_EN | 14:12 EFID | 11 PRI_EN | 10:8 PRI |
-bit7  KEEP    | 6 VSEL     | 5 LEARN_DIS         | 4:0 VIDX
-```
-
-All fields are in network byte order.
-
-* `EFID_EN`, `EFID`: look the destination up under this filtering ID
-  instead of the port's own
-* `PRI_EN`, `PRI`: force the given priority on the frame
-* `KEEP`: keep the 802.1Q tagging of the frame exactly as injected,
-  bypassing the egress tagging rules of the port
-* `VSEL`, `VIDX`: classify the frame into the VLAN at this index of the
-  VLAN table
-* `LEARN_DIS`: do not learn the source address from this frame
-
-The `pmask` word: bit 15 is `ALLOW`, bits 14 to 0 are a port mask.
-
-* `ALLOW` clear: the mask is the egress set, the frame goes to exactly
-  the ports given
-* `ALLOW` set: the ASIC looks the destination up as usual and the mask
-  only limits which ports the result may use
@@ -1,179 +0,0 @@
-# Adding a new device
-
-A device is supported by adding one board definition `.h` and board configuration `.c` file
-under `machine/`. 
-the build selects the definition by name, and CI compiles every file it finds.
-
-To compile for your added device, do:
-```
-make MACHINE=<NAME>
-```
-
-## What a new device consists of
-
-| File | Purpose |
-|------|---------|
-| `machine/<NAME>.c` | the `struct machine machine` board definition |
-| `machine/<NAME>.h` | `MACHINE_MODEL`, the model string shown in the UI and the CLI |
-| `doc/devices/<name>.md` + `doc/supported_devices.md` | (only if the board is verified and you want to support it publicly) user-facing documentation |
-
-`<NAME>` is the machine symbol without its `MACHINE_` prefix, so `MACHINE` is
-passed exactly as spelled on the command line: `make MACHINE=MY_BOARD_1_0`
-needs `machine/MY_BOARD_1_0.c` and `machine/MY_BOARD_1_0.h`.
-
-## Step 1: the model header
-
-`machine/<NAME>.h` only carries the product string. Use the existing files as
-the template:
-
-```c
-#ifndef _MACHINE_MY_BOARD_1_0_H_
-#define _MACHINE_MY_BOARD_1_0_H_
-
-#define MACHINE_MODEL "Brand Model V1.0"
-
-#endif
-```
-
-The device product string is what the CLI or the Web-Interface will print to identify the device; `machine.h` includes it by name.
-
-> [!NOTE]
-> `machine_name` is a `char[30]` and `MACHINE_MODEL` is copied into it at
-> compile time. A longer model string still builds, but SDCC emits
-> `warning 147: excess elements in array of chars initializer` and the name is
-> truncated in the UI. Keep it to 29 characters or less.
-
-## Step 2: the board definition
-
-`machine/<NAME>.c` starts with the shared prelude and then defines the single
-`machine` object. Copy the closest existing board and adjust it — do not start
-from a blank file, the field meanings are easier to see in a real example.
-The best choice is usually a device that has the same number and type of Ethernet
-ports and the same number of SFP+ cages.
-
-```c
-#include "machine_defs.h"
-
-__code const struct machine machine = {
-	.machine_name = MACHINE_MODEL,
-	.isRTL8373 = 1,
-	.min_port = 0,
-	.max_port = 8,
-	.n_sfp = 1,
-	.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
-	.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
-	.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
-
-	.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
-	.sfp_port[0].pin_los = GPIO37,
-	.sfp_port[0].pin_tx_disable = GPIO_NA,
-	.sfp_port[0].sds = 1,
-	.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
-	.reset_pin = GPIO_NA,
-
-	.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28_SYS | LED_29 },
-	.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1 },
-	.led_sets = {
-		{   /* RJ45 ports */
-			LEDS_2G5 | LEDS_LINK,
-			LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
-			0,
-			0
-		}, { /* SFP port, single green LED */
-			LEDS_10G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
-			0,
-			0,
-			0
-		}
-	},
-};
-```
-
-### Fields
-
-| Field | Meaning |
-|-------|---------|
-| `machine_name` | always `MACHINE_MODEL` |
-| `isRTL8373` | `1` for an RTL8373 SoC, `0` for RTL8372 |
-| `min_port` / `max_port` | range of logical port numbers the device has; `min_port` is `0` for RTL8373 boards and `3` for RTL8372 boards (logical ports 1–2 are the SoC's internal ports on the 8372), `max_port` is usually 8. |
-| `n_sfp` | number of SFP+ cages |
-| `n_10g` | SerDes 10G capability used by the RTL837xN init: `0` none, `1` one, `2` two 10G-capable SerDes |
-| `log_to_phys_port[9]` | logical port (0-based index) → physical front-panel port number |
-| `phys_to_log_port[9]` | the inverse, physical port 1 is index 0, unused slots are 0 |
-| `is_sfp[9]` | `0` for copper, `1` for left slot and `2` for right slot |
-| `sfp_port[2]` | per-cage wiring, `sfp_port[0]` is the leftmost cage |
-| `reset_pin` | GPIO of the reset button, `GPIO_NA` if unpopulated |
-| `high_leds` | mux/enable for the LED pins 27–29 (`LED_27`, `LED_28_SYS`, `LED_29`) |
-| `port_led_set[9]` | which LED set (0–3) each logical port uses |
-| `led_sets[4][4]` | Each port can have up to 4 GPIO output pins assigned. 4 sets of LEDs with 4 LED-conditions per set; the conditions define which GPIO pins become active for a port given a port link-state. Which LEDs are then enabled depends on the wiring of the pins to up to 3 LEDs for that port, which can make a logical combination of the 4 LED output-pins. |
-| `led_mux_custom` / `led_mux[28]` | `1` plus the 28 mux values when the stock LED muxing does not fit the board |
-| `mac_flash_offset` | flash offset of the factory MAC address, omit or `0` if the board does not store one |
-
-Each `struct sfp_port` entry holds `pin_detect`, `pin_los`, `pin_tx_disable`,
-`sds` (which SerDes drives the cage) and `i2c` (built with `I2CBUS(sda, scl)`,
-or `GPIO_NA`-based values where a cage has no such pin).
-
-`I2CBUS(...)` only accepts the pin pairs listed in `machine_defs.h`. A wrong
-pair is caught at compile time: SDCC reports
-`error 176: sizeof applied to an incomplete type` pointing at the offending
-`.i2c` line, because the macro deliberately turns an invalid bus number into an
-array of size 0.
-
-### Reusing an existing definition
-
-If the new board is electrically identical to one that already exists — same
-port mapping, same SFP wiring, same LEDs — do not copy the file. Make the new
-`.c` a symlink and keep only a distinct `.h`, so the two boards cannot drift
-apart:
-
-```
-ln -s KP_9000_6XHML_X2.c machine/MY_BOARD_1_0.c
-```
-
-The new board still needs `machine/MY_BOARD_1_0.h` (pick the version number on the PCB) with its own
-`MACHINE_MODEL`, because `MACHINE_MODEL` is what distinguishes the products.
-Existing examples: `machine/PCB_K0402WS_V3.c`, `machine/KP_9000_9XHML_X_V3_2.c`
-and the six `KP_9000_*` revision variants.
-
-Two files that differ only in whitespace or comments are duplicates and should
-be collapsed this way.
-
-## Step 3: build and verify
-
-```
-make MACHINE=MY_BOARD_1_0
-```
-
-The generated flash image appears as `output/rtlplayground-<version>-MY_BOARD_1_0.bin`. An
-unknown or empty `MACHINE` fails immediately with a message naming the expected
-file, before anything is compiled.
-
-Then run the checks CI runs:
-
-```
-make machine_check    # compiles machine/<NAME>.c and machine_init.c for every machine
-make -C test          # host-side unit tests
-```
-
-`make machine_check` discovers the definitions with
-`$(wildcard machine/*.c)`, so a new file is covered without registering it
-anywhere. CI (`.github/workflows/build.yml`) runs it on every push and pull
-request, alongside full builds for a 4+2 and an 8+1 board.
-
-A successful compile only proves the definition is syntactically valid. The
-actual behaviour — port numbering, SFP detection, LEDs — has to be confirmed on
-hardware, and the console commands (`port`, `stat`, `sfp`, `leds`) are the
-tools for that.
-
-## Step 4: documentation
-
-Once the board has been tested on hardware:
-
-1. Add a row to the table in [Supported devices](supported_devices.md).
-2. Add `doc/devices/<name>.md` describing the board, the build target
-   (`make MACHINE=MY_BOARD_1_0`), what works and what is unverified, plus
-   photos and the PCB silkscreen marking.
-3. If the board shares a PCB with other revisions, follow
-   `doc/devices/KP-9000-6XH-X2.md` and document which `MACHINE` to pick for
-   which silkscreen.
-
@@ -1,32 +0,0 @@
-# Automation
-
-## Upload
-
-You can automate upload of the firmware via WEB with curl:
-
-1. Authorize with /login endpoint and save cookie:
-
-   ```bash
-   curl -c cookies.txt  http://${SWITCH_IP}/login -d pwd=${PASSWORD} -i
-   ```
-
-   This will save session cookie in cookies.txt
-2. Send the firmware via form:
-
-    ```bash
-    curl -b cookies.txt http://${SWITCH_IP}/upload -F "uploadedfile=@${FIRMWARE_FILE_PATH}" -i
-    ```
-
-    You can expect that server will close connection, without responding to request.
-    Wait for SWITCH_IP to be responding again.
-
-## Port status
-
-In similar way to upload, you can fetch the json status of the ports.
-
-1. Get the session cookie as for upload.
-2. Hit the `/status.json` with cookie:
-
-    ```bash
-    curl -b cookies.txt http://${SWITCH_IP}/status.json
-    ```
@@ -1,238 +0,0 @@
-# Egress and Ingress Bandwidth Control
-The RTL8372/3 allows to control the bandwidth of data transmitted (egress) and/or
-admitted (ingress) at any given port. Once admitted, packets are internally switched
-at wire-speed, since the backplane of the devices has a bandwidth of 60GBit/s.
-
-The devices schedules transmission of packets by assigning packets to 8 queues
-implemented in hardware per port, which share a total of 8Mbit of memory internal
-to the switching part of the SoCs. Packets are assigned to the respective queues
-based on the priority assigned to a packet, which can be based on various
-properties of a packet such as  IEEE 802.1P priority, DSCP value, physical port
-number, destination or source MAC, Ether-Type-based, CVID, SVID, IPv4 source or
-destination IP, IPv4/IPv6 TOS field, IPv6 Flow Label and even TCP/UDP
-source/destination port. Once in a queue, packets are scheduled for egress
-based on differnent configurable algorithms.
-
-RTLPlayground currently allows only to control the bandwidth at ingress at a port
-or just before packets leave a port. There is no control of the priority assignment
-or queue scheduling mechanisms. The bandwidth can be controlled in steps of 16Kbit/s
-from 16Kbit/s to 10Gbp/s.
-
-The bandwidth control as currently implemented allows e.g. to assign a certain
-share of bandwidth to an attached device (e.g. to share an uplink), or simulate
-connections with low bandwidth and even bad connectivity with packet drops when
-ingress is not controlled by Flow Control but by simply droping packets.
-
-## Ingress/Egress control
-The relevant registers for controlling Ingress and Egress at a port are:
-```
-#define RTL837X_IGBW_CTRL		0x4c10
-#define IGBW_INC_BYPASS_PKT		0x100
-#define IGBW_INC_IFG			0x80
-#define IGBW_ADM_DHCP			0x20
-#define IGBW_ADM_ARPREQ			0x10
-#define IGBW_ADM_RMA			0x08
-#define IGBW_ADM_BPDU			0x04
-#define IGBW_ADM_RTKPKT			0x02
-#define IGBW_ADM_IGMP			0x01
-#define RTL837X_IGBW_PORT_CTRL		0x4C18
-#define RTL837X_IGBW_PORT_FC_CTRL	0x4C8C
-#define RTL837X_EGBW_PORT_CTRL		0x1c34
-#define RTL837X_EGBW_CTRL		0x447c
-#define EGBW_INC_IFG			0x02
-#define EGBW_CPUMODE			0x01
-```
-`RTL837X_IGBW_CTRL/RTL837X_EGBW_CTRL` control the behaviour of the bandwidth control
-at ingress and egress. The flags such as `IGBW_ADM_DHCP`control whether certain types
-of packets such as DHCP are exempt from being ingress controlled. The
-`IGBW_INC_IFG/EGBW_INC_IFG` flags control whether the Inter Frame Gaps are part of
-the bandwidth being controlled. `EGBW_CPUMODE` controls whether packets generated
-by the internal CPU are subject to egress control.
-
-`RTL837X_IGBW_PORT_CTRL/RTL837X_EGBW_PORT_CTRL` configure the bandwidth for ingress
-and egress at a port.
-
-`RTL837X_IGBW_PORT_FC_CTRL` configures whether packets are bandwidth-controlled using
-Flow Control (port-bit set), or simply dropped (port-bit clear).
-
-## Ingress/Egress bandwidth API
-The code currently provides the following functions:
-```
-void bandwidth_setup(void) __banked;
-void bandwidth_ingress_set(uint8_t port, __xdata uint32_t bw) __banked;
-void bandwidth_ingress_disable(uint8_t port) __banked;
-void bandwidth_ingress_drop(uint8_t port) __banked;
-void bandwidth_egress_set(uint8_t port, __xdata uint32_t bw) __banked;
-void bandwidth_egress_disable(uint8_t port) __banked;
-void bandwidth_status(uint8_t port) __banked;
-```c
-
-`bandwidth_setup()` is called at boot-time and configures excluding all special packets
-that may be for the CPU and packets outgoing from the CPU to be excluded from bandwidth
-control. IFG is not part of the bandwidth calculation.
-
-`bandwidth_ingress_set()` enables ingress bandwidth control for a particular port given
-the specified bandwidth. This also enabled Flow Control at a port.
-
-`bandwidth_ingress_set()` enables egress bandwidth control for a particular port given
-the specified bandwidth
-
-`bandwidth_ingress_disable() / bandwidth_egress_disable()` disable ingress and egress
-bandwidth control at a given port
-
-`bandwidth_ingress_drop(port)` configures packets exceeding bandwidth limitations to
-simply be dropped
-
-`bandwidth_status(port)` shows the current bandwidth control status for a given port
-
-## Bandwidth control configuration on the Serial Console
-The following commands are provided on the serial console:
-```
-> bw [in|out|status] <port> [<hexvalue>|off|drop]
-  Configures or shows the status of bandwidth control
-```
-The bandwidth is given as the `<hexvalue>` in Kbit/s. Note that the control is only
-possible at a granularity of 16 Kbit/s and the minimum value is also 16 Kbit/s. The
-hexadecimal numbers must be given in full bytes, i.e. have an even number of digits.
-
-To enable bandwidth control of ingress for physical port 2 to be set to 256 Kbit/s
-do:
-```
-> bw in 2 0100 
-```
-
-To drop packets when the bandwidth is exceeeded at port 2 do:
-```
-> bw in 2 drop 
-```
-
-To disable bandwidth control for incoming packets on port 2 do:
-```
-> bw in 2 off
-```
-
-## Bandwidth configuration via the Web Interface
-Not implemented, yet!
-
-## A Test using iperf3
-The following is and example how to test bandwidth control with a signle Linux device using
-network namespaces to route packets between a client and a server on the same Linux device
-through an external switch.
-
-You will need 2 network intefaces on the linux device, say, 2 USB-Ethernet controllers called
-eth0 and eth1: 
-```
-$ sudo ip netns add client
-$ sudo ip netns add server
-
-$ sudo ip link set dev eth0 netns client
-$ sudo ip link set dev eth1 netns server
-
-$ sudo ip netns exec client ip link set dev eth0 up
-$ sudo ip netns exec server ip link set dev eth1 up
-
-$ sudo ip netns exec client ip addr add dev eth0 192.168.99.1/24
-$ sudo ip netns exec server ip addr add dev eth1 192.168.99.2/24
-
-$ sudo ip netns exec server iperf3 -s
-```
-This will start an iper3 server in the above shell.
-
-In a different shell you can now run the iperf3 client against your server:
-```
-$ sudo ip netns exec client iperf -c 192.168.99.2
-```
-The LEDs on your switch where your network adapters are connected should start to flicker.
-On a 1GBit connection, you should see:
-```
-$ sudo ip netns exec client iperf3 -c 192.168.99.2
-Connecting to host 192.168.99.2, port 5201
-[  5] local 192.168.99.1 port 46776 connected to 192.168.99.2 port 5201
-[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
-[  5]   0.00-1.00   sec   114 MBytes   952 Mbits/sec    0    339 KBytes       
-[  5]   1.00-2.00   sec   113 MBytes   946 Mbits/sec    0    356 KBytes       
-[  5]   2.00-3.00   sec   112 MBytes   937 Mbits/sec    0    390 KBytes       
-[  5]   3.00-4.00   sec   112 MBytes   942 Mbits/sec    0    390 KBytes       
-[  5]   4.00-5.00   sec   112 MBytes   943 Mbits/sec    0    390 KBytes       
-[  5]   5.00-6.00   sec   112 MBytes   944 Mbits/sec    0    390 KBytes       
-[  5]   6.00-7.00   sec   112 MBytes   938 Mbits/sec    0    390 KBytes       
-[  5]   7.00-8.00   sec   112 MBytes   942 Mbits/sec    0    410 KBytes       
-[  5]   8.00-9.00   sec   113 MBytes   947 Mbits/sec    0    410 KBytes       
-[  5]   9.00-10.00  sec   112 MBytes   940 Mbits/sec    0    410 KBytes       
- - - - - - - - - - - - - - - - - - - - - - - - -
-[ ID] Interval           Transfer     Bitrate         Retr
-[  5]   0.00-10.00  sec  1.10 GBytes   943 Mbits/sec    0            sender
-[  5]   0.00-10.00  sec  1.10 GBytes   941 Mbits/sec                  receiver
-```
-
-Now, we limit ingress on port 1 (connected to eth0) to 4 MBit/s:
-```> bw in 1 1000
-bandwidth_ingress_set called, port 04
-RTL837X_IGBW_PORT_CTRL:0x00100100
-RTL837X_IGBW_PORT_FC_CTRL:0x00000010
-```
-
-We now get:
-```
-$ sudo ip netns exec client iperf3 -c 192.168.99.2
-[  5] local 192.168.99.1 port 43324 connected to 192.168.99.2 port 5201
-[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
-[  5]   0.00-1.00   sec  1.12 MBytes  9.43 Mbits/sec    0    160 KBytes       
-[  5]   1.00-2.00   sec   640 KBytes  5.24 Mbits/sec    0    160 KBytes       
-[  5]   2.00-3.00   sec   384 KBytes  3.15 Mbits/sec    0    160 KBytes       
-[  5]   3.00-4.00   sec   384 KBytes  3.15 Mbits/sec    0    160 KBytes       
-[  5]   4.00-5.00   sec   640 KBytes  5.24 Mbits/sec    0    160 KBytes       
-[  5]   5.00-6.00   sec   256 KBytes  2.10 Mbits/sec    0    160 KBytes       
-[  5]   6.00-7.00   sec   640 KBytes  5.24 Mbits/sec    0    160 KBytes       
-[  5]   7.00-8.00   sec   384 KBytes  3.15 Mbits/sec    0    160 KBytes       
-[  5]   8.00-9.00   sec   640 KBytes  5.24 Mbits/sec    0    160 KBytes       
-[  5]   9.00-10.00  sec   256 KBytes  2.10 Mbits/sec    0    160 KBytes       
- - - - - - - - - - - - - - - - - - - - - - - - -
-[ ID] Interval           Transfer     Bitrate         Retr
-[  5]   0.00-10.00  sec  5.25 MBytes  4.40 Mbits/sec    0            sender
-[  5]   0.00-10.16  sec  4.75 MBytes  3.92 Mbits/sec                  receiver
-
-iperf Done.
-```
-Which is the 4Mbit/s we configured. There are no packet drops (retries) because
-Flow Control is used to signal the Ethernet adapter on the incoming interface
-(port 1 of the router) to slow down.
-
-We can also configure a mere 256KBit/s and packet drop to simulate a bad connection:
-```
-> bw in 1 0100
-bandwidth_ingress_set called, port 04
-RTL837X_IGBW_PORT_CTRL:0x00100010
-RTL837X_IGBW_PORT_FC_CTRL:0x00000010
-
-> bw in 1 drop
-RTL837X_IGBW_PORT_FC_CTRL:0x00000000
-```
-
-We now get:
-```
-$ sudo ip netns exec client iperf3 -c 192.168.99.2
-Connecting to host 192.168.99.2, port 5201
-[  5] local 192.168.99.1 port 46060 connected to 192.168.99.2 port 5201
-[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
-[  5]   0.00-1.00   sec   384 KBytes  3.14 Mbits/sec    2   1.41 KBytes       
-[  5]   1.00-2.00   sec  0.00 Bytes  0.00 bits/sec   54   1.41 KBytes       
-[  5]   2.00-3.00   sec  0.00 Bytes  0.00 bits/sec   31   29.7 KBytes       
-[  5]   3.00-4.00   sec  0.00 Bytes  0.00 bits/sec    2   1.41 KBytes       
-[  5]   4.00-5.00   sec  0.00 Bytes  0.00 bits/sec   23   1.41 KBytes       
-[  5]   5.00-6.00   sec   128 KBytes  1.05 Mbits/sec   16   14.1 KBytes       
-[  5]   6.00-7.00   sec  0.00 Bytes  0.00 bits/sec    2   1.41 KBytes       
-[  5]   7.00-8.00   sec  0.00 Bytes  0.00 bits/sec   11   1.41 KBytes       
-[  5]   8.00-9.00   sec   128 KBytes  1.05 Mbits/sec    9   8.48 KBytes       
-[  5]   9.00-10.00  sec  0.00 Bytes  0.00 bits/sec    2   1.41 KBytes       
- - - - - - - - - - - - - - - - - - - - - - - - -
-[ ID] Interval           Transfer     Bitrate         Retr
-[  5]   0.00-10.00  sec   640 KBytes   524 Kbits/sec  152            sender
-[  5]   0.00-10.00  sec   256 KBytes   210 Kbits/sec                  receiver
-
-iperf Done.
-```
-Which shows a large number of retries due to dropped packets and an average number
-of received packets (the client sends the packets to the server, and they are sent
-back to the client by the server) of 210 KBit/s, the number is higher for the transmitted
-packets, because they may include dropped packets.
@@ -1,177 +0,0 @@
-### 2M-PCB23-V2.2
-
-## Brands
-| Brand    | Type            | Managed | PCB           | Flash | Chip RTL    |
-|----------|-----------------|---------|---------------|-------|-------------|
-| keepLINK | KP-9000-9XHML-X | Yes     | 2M-PCB23-V2.2 | 2M    | 8373 + 8224 |
-
-## PCB
-
-<img src="photos/2M-PCB23-V2.2-managed/2M-PCB23-V2.2-top.jpg" width="300" />
-
-## Port overview
-
-```
-┌─────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────┐
-│                                                                                                       ┌──────────┐          │
-│     ┌─────────┐ ┌─────────┐ ┌─────────┐ ┌─────────┐ ┌─────────┐ ┌─────────┐ ┌─────────┐ ┌─────────┐   │ SFP(J13) │          │
-│     │  RJ45   │ │  RJ45   │ │  RJ45   │ │  RJ45   │ │  RJ45   │ │  RJ45   │ │  RJ45   │ │  RJ45   │   │ PORT   9 │          │
-│     │  PORT 1 │ │  PORT 2 │ │  PORT 3 │ │  PORT 4 │ │  PORT 5 │ │  PORT 6 │ │  PORT 7 │ │  PORT 8 │   │ MAC    8 │ O (PWR)  │
-│  O  │  MAC  0 │ │  MAC  1 │ │  MAC  2 │ │  MAC  3 │ │  MAC  4 │ │  MAC  5 │ │  MAC  6 │ │  MAC  7 │   │ SerDes 1 │ O (SFP)  │
-│ RST └─────────┘ └─────────┘ └─────────┘ └─────────┘ └─────────┘ └─────────┘ └─────────┘ └─────────┘   └──────────┘          │
-└─────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────┘
-```
-
-# Connectors
-
-### J13, SFP connector
-
-| SFP Pin | Signal            | GPIO   | Notes                          |
-| ------- | ----------------- | ------ | ------------------------------ |
-| 2       | TX_FAULT          | ??     |                                |
-| 3       | TX_DISABLE        | ??     |                                |
-| 4       | MODDEF2 – SDA     | GPIO39 |                                |
-| 5       | MODDEF1 – SCL     | GPIO40 |                                |
-| 6       | MODDEF0 – PRESENT | GPIO30 | "OE Exist" reported by `fiber` |
-| 7       | RATE SEL          | ??     |                                |
-| 8       | LOS	              | GPIO37 | "OE LOS" reported by `fiber`   |
-| 9       | TO?               | ??     |                                |
-
-### T5, serial console
-
-| pin | GPIO   | Signal         |
-| --- | ------ | -------------- |
-| 1   | GPIO32 | U0RXD (Input)  |
-| 2   | GND    | Ground         |
-| 3   | GPIO31 | U0TXD (Output) |
-
-### S1, unknown connector
-
-| pin | GPIO     | Signal         |
-| --- | -------- | -------------- |
-| 1   | ???      |                |
-| x   |          |                |
-| 3   | ???      |                |
-| 4   | ???      |                |
-| 5   | ???      |                |
-
-Potentially slave interface or SMI.
-
-### U7, flash memory
-
-Flash chip is FM25Q16A.
-
-### Reset button
-
-GPIO54
-
-## Register values
-
-As probed with `regget` on stock firmware "V1.6".
-
-### Model
-
-| Name                      | Addr   | Value      |
-| ------------------------- | ------ | ---------- |
-| MODEL_NAME_INFO           | 0x0004 | 0x83730000 |
-| CHIP_MODE_INFO            | 0x0008 | 0x00008000 |
-| CHIP_INFO                 | 0x000C | 0x00300000 |
-
-### GPIO
-
-| Name                      | Addr   | Value      |
-| ------------------------- | ------ | ---------- |
-| GPIO_OUT0                 | 0x003c | 0x10000000 |
-| GPIO_OUT1                 | 0x0040 | 0x00000010 |
-| GPIO_OE0                  | 0x004c | 0x10000000 |
-| GPIO_OE1                  | 0x0050 | 0x00000010 |
-| BOND_INFO                 | 0x7f60 | 0x00000fff |
-| STRAP_INFO                | 0x7f64 | 0x0002f515 |
-| IO_DRVING_0               | 0x7f68 | 0x00000000 |
-| IO_DRVING_1               | 0x7f6c | 0x00000000 |
-| IO_DRVING_2               | 0x7f70 | 0x00000000 |
-| IO_SLEW_0                 | 0x7f74 | 0x00000000 |
-| IO_SLEW_1                 | 0x7f78 | 0x00000000 |
-| IO_SLEW_2                 | 0x7f7c | 0x00000000 |
-| IO_SMT_EN_0               | 0x7f80 | 0xffffffff |
-| IO_SMT_EN_1               | 0x7f84 | 0xffffffff |
-| IO_SMT_EN_2               | 0x7f88 | 0x0003ffff |
-| IO_MUX_SEL_0              | 0x7f8c | 0x28000000 |
-| IO_MUX_SEL_1              | 0x7f90 | 0x40000041 |
-| IO_MUX_SEL_2              | 0x7f94 | 0x00000000 |
-
-### LED
-
-| Name                      | Addr   | Value      |
-| ------------------------- | ------ | ---------- |
-| LED_GLB_CTRL              | 0x6520 | 0x0023e0f0 |
-| LED3_0_SET3_2_CTRL1       | 0x6524 | 0xff001400 |
-| LED3_0_SET1_0_CTRL1       | 0x6528 | 0x000f0000 |
-| LED3_2_SET3_CTRL0         | 0x652c | 0x007f013f |
-| LED1_0_SET3_CTRL0         | 0x6530 | 0x02000400 |
-| LED3_2_SET2_CTRL0         | 0x6534 | 0x01400141 |
-| LED1_0_SET2_CTRL0         | 0x6538 | 0x01440170 |
-| LED3_2_SET1_CTRL0         | 0x653c | 0x18000041 |
-| LED1_0_SET1_CTRL0         | 0x6540 | 0x0044017f |
-| LED3_2_SET0_CTRL0         | 0x6544 | 0x00000044 |
-| LED1_0_SET0_CTRL0         | 0x6548 | 0x00410175 |
-| LED_PORT_SET_SEL_CTRL     | 0x654c | 0x00010000 |
-| SW_LED_LOAD               | 0x6550 | 0x00000000 |
-| LED_PORT_SW_EN_CTRL[0..7] | 0x6554 | 0x00000000 |
-| LED_PORT_SW_EN_CTRL[8]    | 0x6558 | 0x00000000 |
-| LED_PORT_SW_CTRL[0]       | 0x655c | 0x00000000 |
-| LED_PORT_SW_CTRL[1]       | 0x6560 | 0x00000000 |
-| LED_PORT_SW_CTRL[2]       | 0x6564 | 0x00000000 |
-| LED_PORT_SW_CTRL[3]       | 0x6568 | 0x00000000 |
-| LED_PORT_SW_CTRL[4]       | 0x656c | 0x00000000 |
-| LED_PORT_SW_CTRL[5]       | 0x6570 | 0x00000000 |
-| LED_PORT_SW_CTRL[6]       | 0x6574 | 0x00000000 |
-| LED_PORT_SW_CTRL[7]       | 0x6578 | 0x00000000 |
-| LED_PORT_SW_CTRL[8]       | 0x657c | 0x00000000 |
-| LED_LOAD_LV1_10G          | 0x6580 | 0x000fa000 |
-| LED_LOAD_LV2_10G          | 0x6584 | 0x00271000 |
-| LED_LOAD_LV3_10G          | 0x6588 | 0x004e2000 |
-| LED_LOAD_LV1_5G           | 0x658c | 0x000fa000 |
-| LED_LOAD_LV2_5G           | 0x6590 | 0x00271000 |
-| LED_LOAD_LV3_5G           | 0x6594 | 0x004e2000 |
-| LED_LOAD_LV1_2P5G         | 0x6598 | 0x000fa000 |
-| LED_LOAD_LV2_2P5G         | 0x659c | 0x00271000 |
-| LED_LOAD_LV3_2P5G         | 0x65a0 | 0x004e2000 |
-| LED_LOAD_LV1_1G           | 0x65a4 | 0x000fa000 |
-| LED_LOAD_LV2_1G           | 0x65a8 | 0x00271000 |
-| LED_LOAD_LV3_1G           | 0x65ac | 0x004e2000 |
-| LED_LOAD_LV1_500M         | 0x65b0 | 0x0007d000 |
-| LED_LOAD_LV2_500M         | 0x65b4 | 0x00138800 |
-| LED_LOAD_LV3_500M         | 0x65b8 | 0x00271000 |
-| LED_LOAD_LV1_100M         | 0x65bc | 0x00019000 |
-| LED_LOAD_LV2_100M         | 0x65c0 | 0x0003e800 |
-| LED_LOAD_LV3_100M         | 0x65c4 | 0x0007d000 |
-| LED_LOAD_LV1_10M          | 0x65c8 | 0x00002800 |
-| LED_LOAD_LV2_10M          | 0x65cc | 0x00006400 |
-| LED_LOAD_LV3_10M          | 0x65d0 | 0x0000c800 |
-| LED_P_LOAD_CTRL           | 0x65d4 | 0x00000000 |
-| LED_GLB_ACTIVE            | 0x65d8 | 0x3ffbedff |
-| LED_GLB_IO_EN             | 0x65dc | 0x77ffffff |
-| LED_GLB_MUX_1             | 0c65e0 | 0x05102040 |
-| LED_GLB_MUX_2             | 0x65e4 | 0x0c289206 |
-| LED_GLB_MUX_3             | 0x65e8 | 0x1245038d |
-| LED_GLB_MUX_4             | 0x65ec | 0x19616554 |
-| LED_GLB_MUX_5             | 0x65f0 | 0x2079d71a |
-| LED_GLB_MUX_6             | 0x65f4 | 0x000238a1 |
-| LED_RLDP_CTRL_1           | 0x65f8 | 0x00000019 |
-| LED_RLDP_CTRL_2           | 0x65fc | 0xffffffff |
-| LED_RLDP_CTRL_3           | 0x6600 | 0x00006600 |
-| LED_DUMY_0_ADDR           | 0x6604 | 0x00000000 |
-| LED_DUMY_1_ADDR           | 0x6608 | 0x00000000 |
-
-# LEDs
-
-| Name                          | Components                  | Controlled by              |
-| ----------------------------- | --------------------------- | -------------------------- |
-| RJ45 Right Green ("LINK/ACT") |                             | RJ45 LED0                  |
-| RJ45 Left Orange ("2.5G")     |                             | RJ45 LED1                  |
-| RJ45 Left Green  ("1G")       |                             | RJ45 LED2                  |
-| "P" (PWR)                     | Top LED in "LED6" stack     | probably pulled from Vcc   |
-| SFP Link ("9")                | Bottom LED in "LED6" stack  | SFP LED0                   |
-| ??                            | D23                         | SFP LED1                   |
-| ??                            | D22                         | SFP LED2                   |
@@ -5,30 +5,13 @@
 |---|---|---|---|---|---|
 | keepLINK | KP-9000-9XHML-X | Yes|  2M-PCB23-V3.1 | 2M| 8273N + 8224N |

-## PCB
-
-<img src="photos/2M-PCB23-V3.1-managed/2M-PCB23-V3.1-top.jpeg" width="300" />
-
-## Port overview
-
-```
-┌─────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────┐
-│                                                                                                       ┌──────────┐          │
-│     ┌─────────┐ ┌─────────┐ ┌─────────┐ ┌─────────┐ ┌─────────┐ ┌─────────┐ ┌─────────┐ ┌─────────┐   │ SFP (J4) │          │
-│     │  RJ45   │ │  RJ45   │ │  RJ45   │ │  RJ45   │ │  RJ45   │ │  RJ45   │ │  RJ45   │ │  RJ45   │   │ PORT   9 │          │
-│     │  PORT 1 │ │  PORT 2 │ │  PORT 3 │ │  PORT 4 │ │  PORT 5 │ │  PORT 6 │ │  PORT 7 │ │  PORT 8 │   │ MAC    8 │ O (PWR)  │
-│  O  │  MAC  0 │ │  MAC  1 │ │  MAC  2 │ │  MAC  3 │ │  MAC  4 │ │  MAC  5 │ │  MAC  6 │ │  MAC  7 │   │ SerDes 1 │ O (SFP)  │
-│ RST └─────────┘ └─────────┘ └─────────┘ └─────────┘ └─────────┘ └─────────┘ └─────────┘ └─────────┘   └──────────┘          │
-└─────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────┘
-```
-
 # Connectors
 |`J4` SFP PINs | Signal | Component | GPIO | Notes |
 |---|---|---|---|---|
 |2|	TX_FAULT	        | | --- | | 
 |3|	TX_DISABLE	      | | --- | Pull down - 0R |
-|4|	MODDEF2 – SDA     |	b-r273 | GPIO39-SDA4 | |
-|5|	MODDEF1 – SCL     | b-r274 | GPIO40-SCL3 | |
+|4|	MODDEF2 – SDA     |	b-r273 | GPIO39 | |
+|5|	MODDEF1 – SCL     | b-r274 | GPIO40 | |
 |6|	MODDEF0 – PRESENT | B-R275 | GPIO38 |  |
 |7|	RATE SEL          |	| ---    |  | 
 |8|	LOS	              | B-R276 | GPIO38 |  | 
@@ -48,26 +31,15 @@ Note: component numbering `<L>-<REFDES>-<SIDE>`
 | 3 | GPIO32 | U0RXD (Input) |
 | 4 | 3V3 | PWR |

-### T7, Slave Interface
-|`T7` pin|what|Signal|Components|
-|---|---|---|---|
-| 1 | Slave Interface | Slave SCK/SCL/MDC/EE_SCL | U7-6 |
-| 2 | GND   | | |
-| 3 | Slave Interface | Slave SDI/SDA/MDIO/EE_SDA | U7-5 |
-| 4 | 3V3   | | |
-| 5 | GPIO? | | |
-| 6 | GPIO? | | |
-
-`U7` can be a standard I2C eeprom memory, like `24LC32`.
-
-The Slave Interface allows an extenal host to controll the SOC even if the internal MCU is used.
-Depending on the `IF_SEL` bootstrap resistors, this can me `I2C`, `SPI` or `SMI`.
-On this device it is `I2C` on address `0b1011100` or `0x5c` (7-bit notation).
-
-* I2c Read:  must be a write_read opperation `<Dev-ADDR><RegAddr15:8><RegAddr7:0>` `<DevAddr><Data7:0><Data15:8><Data23:16><Data31:24>`.
-* I2c Write: `<Dev-ADDR><RegAddr15:8><RegAddr7:0><DevAddr><Data7:0><Data15:8><Data23:16><Data31:24>`.
-
-Example register `0x0004` return chip id `0x00, 0x00, 0x72, 0x83` = `0x83720000`.
+### T7
+|`T7` pin|what|Signal|
+|---|---|---|
+| 1 | GPIO | |
+| 2 | GND    | |
+| 3 | GPIO | |
+| 4 | 3V3    | |
+| 5 | GPIO | |
+| 6 | GPIO | |

 ### T9
 |`T9` SMI | Signal | Component | GPIO | Notes |
@@ -95,23 +67,23 @@ Reset-line found at `T-D6-L`, `T-R83`, `T-R97`, `T-R94`, `T-R93` active-low.
 | HEX VAL. | GPIO   | Component | What |  | GPIO | Component | What |
 | -------- | ------ |  ---- | ---- | ---- | ---- | ---- | ---- |
 | 00000001 | GPIO00 | T-R34-R, P1-LED-YL      |?      |   | GPIO32 | B-r126-r  | U0RXD |
-| 00000002 | GPIO01 | T-R99-R, P1-LED-GR      |?      |   | GPIO33 | |  |
-| 00000004 | GPIO02 |                         |?      |   | GPIO34 | B-R172, To RTL8224 | SMI-MDC0  |
-| 00000008 | GPIO03 | T-R113-R, P2-LED-GR     |?      |   | GPIO35 | B-R173, To RTL8224 | SMI-MDIO0 |
-| 00000010 | GPIO04 | T-R115-R, P3-LED-YL     |?      |   | GPIO36 | | |  |
-| 00000020 | GPIO05 | T-R117-R, P3-LED-GR     |?      |   | GPIO37 | To RTL8224 ?? | Already driver low |  |
-| 00000040 | GPIO06 |                         |?      |   | GPIO38 | sfp-6 via B-R275, sfp-8 via B-R276 | SFP-PRESENT |
-| 00000080 | GPIO07 |                         |?      |   | GPIO39 | sfp-4, b-r273, B-r143 | I2C4-SDA |
-| 00000100 | GPIO08 |                         |       |   | GPIO40 | T9-2, sfp-5 b-r274, B-r146  | I2C3-SCL |
-| 00000200 | GPIO09 |                         |LEDx[^1] | | GPIO41 | T9-1,  B-r143 | | I2C3-SDA (Unused) |
+| 00000002 | GPIO01 | T-R99-R, P1-LED-GR      |?      |   | GPIO33 |  |  |
+| 00000004 | GPIO02 |                         |?      |   | GPIO34 | B-R172, To RTL8225 | Already driver HIGH INT?  |
+| 00000008 | GPIO03 | T-R113-R, P2-LED-GR     |?      |   | GPIO35 | B-R173, To RTL8225 | Easy to pulldown Reset? |
+| 00000010 | GPIO04 | T-R115-R, P3-LED-YL     |?      |   | GPIO36 || |  |
+| 00000020 | GPIO05 | T-R117-R, P3-LED-GR     |?      |   | GPIO37 | To RTL8225 | Already driver low I2C-SCL?   |  |
+| 00000040 | GPIO06 |                         |?      |   | GPIO38 | sfp-6 via B-R275, sfp-8 via B-R276 |  |
+| 00000080 | GPIO07 |                         |?      |   | GPIO39 | sfp-4, b-r273, B-r143 |  |
+| 00000100 | GPIO08 |                         |       |   | GPIO40 | T9-2, sfp-5 b-r274, B-r146  | SMI-MDC  |
+| 00000200 | GPIO09 |                         |LEDx[^1] | | GPIO41 | T9-1, | SMI-MDO , B-r143  |
 | 00000400 | GPIO10 |                         |         | | GPIO42 | U6?8?-P6, T-R | SPI-MEMORY, CLK |
 | 00000800 | GPIO11 |                         |LEDx[^1] | | GPIO43 | U6?8?-P5, T-R | SPI-MEMORY, DI,IO0 |
 | 00001000 | GPIO12 |                         |LEDx[^1] | | GPIO44 | U6?8?-P2, T-R | SPI-MEMORY, DO,IO1 |
 | 00002000 | GPIO13 |                         |LEDx[^1] | | GPIO45 | U6?8?-P1, T-R | SPI-MEMORY, CS  |
-| 00004000 | GPIO14 |                         |LEDx[^1] | | GPIO46 | T10-6 | SPI0-SCK |
-| 00008000 | GPIO15 |                         |LEDx[^1] | | GPIO47 | T10-2 | SPI0-SDA |
-| 00010000 | GPIO16 |                         |LEDx[^1] | | GPIO48 | T10-4, J6 (BUTTON RESET) | SPI1-SCK |
-| 00020000 | GPIO17 |                         |LEDx[^1] | | GPIO49 | T10-1 | SPI1-SDA |
+| 00004000 | GPIO14 |                         |LEDx[^1] | | GPIO46 | T10-6 |  |
+| 00008000 | GPIO15 |                         |LEDx[^1] | | GPIO47 | T10-2 |  |
+| 00010000 | GPIO16 |                         |LEDx[^1] | | GPIO48 | T10-4, J6 (BUTTON RESET) |  |
+| 00020000 | GPIO17 |                         |LEDx[^1] | | GPIO49 | T10-1 |  |
 | 00040000 | GPIO18 |                         |LEDx[^1] | | GPIO50 |  |  |
 | 00080000 | GPIO19 |                         |LEDx[^1] | | GPIO51 |  |  |
 | 00100000 | GPIO20 |                         |LEDx[^1] | | GPIO52 |  |  |
@@ -124,8 +96,8 @@ Reset-line found at `T-D6-L`, `T-R83`, `T-R97`, `T-R94`, `T-R93` active-low.
 | 08000000 | GPIO27 |                         |?        | | GPIO59 |  |  |
 | 10000000 | GPIO28 |                         |         | | GPIO60 |  |  |
 | 20000000 | GPIO29 |                         |         | | GPIO61 |  |  |
-| 40000000 | GPIO30 | RTL8224N Reset          |RTL8224  | | GPIO62 | To RTL8224 | Already driver   |  |
-| 80000000 | GPIO31 | B-r129-r?               |U0TXD    | | GPIO63 |  |  |
+| 40000000 | GPIO30 |                         |SFP-DETE | | GPIO62 | To RTL8225 | Already driver INT?   |  |
+| 80000000 | GPIO31 |  B-r129-r?              |U0TXD    | | GPIO63 |  |  |

 ## GPIO Register Input value

@@ -158,4 +130,4 @@ Chip can deliver up to 5A and the sweetspot is at 2A.
 So higher power SFP-modules should work.


-[^1]: LEDs are found by just plugin a RJ45 connector and see with cmd `gpio` the status change. But the bit pattern for port 1,2 are diffrent from port 3,4.
+[^1]: LEDs are found by just plugin a RJ45 connector and see with cmd `gpio` the status change. But the bit pattern for port 1,2 are diffrent from port 3,4.
@@ -1,40 +0,0 @@
-### 2M-PCB23-V3.2
-
-## Brands
-|Brand|Type|Managed|PCB|Flash|Chip RTL|
-|---|---|---|---|---|---|
-| keepLINK | KP-9000-9XHML-X | Yes|  2M-PCB23-V3.2 | 2M (Winbond 25Q) | |
-
-The original web interface reports this board as hardware version V3.2
-(original firmware V100.9.25, January 2026).
-
-## PCB
-
-<img src="photos/2M-PCB23-V3.2-managed/2M-PCB23-V3.2-top.jpeg" width="300" />
-
-## Compared to V3.1
-
-The component placement matches [2M-PCB23-V3.1](2M-PCB23-V3_1.md): same
-positions for the flash (U8), the T7/T8/T9/T10 headers, the SFP cage and its
-LED, and the unpopulated U7/U9 footprints. Build with
-`make MACHINE=KP_9000_9XHML_X_V3_2`, whose board file is a symlink to the V3.1
-definition and only differs in the reported name.
-
-## Tested
-
-Installed from the original firmware through its web interface with
-`installer/output/rtlplayground_oem_upgrade.bin`, then:
-
- RJ45 ports link at 2.5G; LEDs: orange at 2.5G, green below
- SFP port: module detected with vendor/model/serial and DOM readings
-  (temperature, Vcc, TX bias, TX/RX power), link up at 10G
- factory MAC read from flash (0x1FC000)
- reset button (GPIO48): held for more than 10 s it restores the default config
-
-## Flash access
-
-Reading the flash in-circuit with a SOIC-8 clip did not work: the chip ID
-comes back as `EF FF FF` (only the manufacturer byte is right) and reads
-return 0xff, the same as on a V3.1 board. The switch chip is powered through
-the clip and keeps driving the SPI lines. Make sure a way back is acceptable
-before installing, or hold the switch chip in reset while reading.
@@ -1,55 +0,0 @@
-# 2G040210GSM
-
-The following is a documentation for the managed switch marked as `2G040210GSM`
-and sold by Mokerlink.
-
-### Label specifications
-
- **Name**: 4-port 2.5G Web Managed Switch
- **Ports**:
-  - 4 × RJ45: 10/100/1000/2500 Mbps
-  - 2 × SFP+: 1000 / 2500 / 10000 Mbps
- **Power**: 12V DC, 1A barrel connector 
-
-### What works
-The device is fully supported:
- All 4 2.5GBASE-T RJ45 ports work at 10/100/1000/2500 Mbps
- The SFP+ port supports 1G, 2.5G and 10G modules 
- LEDs work with the same indiciations as the OEM firmware (build with `make MACHINE=KP_9000_6XHML_X2_V1_1` if building yourself, or use the corresponding pre-compiled binary)
- untested due to missing Hardware: SFP+ ports equipped with 1G or 2.5G SFPs.
-
-### Hardware overview
-Front
-
-<img src="photos/2M-PCB43-V1.1-managed/2M-PCB43-V1.1-front.jpeg" width="300" />
-
-Label
-
-<img src="photos/2M-PCB43-V1.1-managed/2M-PCB43-V1.1-label.jpeg" width="300" />
-
-### PCB overview
-
-**Board markings**
- Top silkscreen: 2M-PCB43-V1.1
-
-Top side
-
-<img src="photos/2M-PCB43-V1.1-managed/2M-PCB43-V1.1-top.jpeg" width="300" />
-
-Bottom
-
-<img src="photos/2M-PCB43-V1.1-managed/2M-PCB43-V1.1-bottom.jpeg" width="300" />
-
-### J1, serial console
-
-| `J8` pin | Signal      |
-| -------- | ----------- |
-| 1        | RX (Input)  |
-| 2        | TX (Output) |
-| 3        | GND         |
-| 4        | 3V3         |
-
-
-## Power supply
-
-Input power is delivered via barell plug, `12V 1A` adapter was provided.
@@ -1,32 +0,0 @@
-# MokerLink POE-2G080110GS
-
-The `POE-2G080110GS` is an unmanaged 8x2.5G RJ45 and 1xSFP+ PoE switch sold by Mokerlink. There is also a `POE-2G080110GSM` managed version of the switch which may be similar but this has not been verified on actual hardware.
-
-## Brands
-| Brand  | Type             |Managed| PCB              | Flash           | Chip RTL      |
-|--------|------------------|-------|------------------|-----------------|---------------|
-| Mokerlink | POE-2G080110GS | No | 2M-PCB51-ML-V1.1 | 4MB (W25Q32JV) | 8373N + 8224N |
-
-## Hardware overview
-Front
-
-<img src="photos/POE-2G080110GS/POE-2G080110GS-front.jpg" width="300" />
-
-Label
-
-<img src="photos/POE-2G080110GS/POE-2G080110GS-label.jpg" width="300" />
-
-The stock firmware from a POE-2G080110GS device had a sha256sum of `4c280853465eaad80e1772075c0f2d29c11fb8c561547f06353d3a5443c388e9`.
-
-### PCB
-
-Top silkscreen is marked `2M-PCB51-ML-V1.1`. PoE is provided by RTL8238C. Flash chip is 4 MB Winbond 25Q32JV (U8).
-
-<img src="photos/POE-2G080110GS/POE-2G080110GS-pcb.jpg" width="300" />
-
-> [!CAUTION]
-> This device operates on mains voltage, which can be a dangerous or potentially lethal hazard. Even after the device is unplugged, high-voltage capacitors can remain charged afterward and may still shock you. Do not attempt to open/disassemble a mains powered device unless you understand how to do so safely. Also, opening the device may void your warranty.
-
-## Notes
-
-The stock firmware blinks both the 2.5G and 1G LEDs on activity, despite the front of the device indicating that each LED should be independent. The `POE_2G080110GS` machine config behaves as the front of the device indicates (and what seems more logical) -- each port LED turns on and blinks independently.
@@ -1,70 +0,0 @@
-# F7008-2.5
-
-Documentation for the unmanaged 8 + 1 switch sold as `7018-2.5G` by Guangnianwei
-(光年微), board marking `F7008-2.5`, PCB `F7008-2.5GPOE-V1.2`.
-
-### Brands
-
-| Brand | Type | Managed | PCB | Flash | Chip RTL |
-|-------|------|---------|-----|-------|----------|
-| Guangnianwei (光年微) | 7018-2.5G | No | F7008-2.5GPOE-V1.2 | W25Q64JVSSIQ | 8373N + 8224N |
-
-### What works
-
- All eight 2.5GBASE-T RJ45 ports at 10/100/1000/2500 Mbps
- SFP+ port with 1G/2.5G/10G modules
- LEDs of the eight RJ45 ports
-
-### Not verified
-
- The LED pads for the SFP+ cage are not mapped yet. The SFP+ lamps are left
-  undriven, so an inserted module lights nothing.
- The UART header footprint is present but unpopulated, and no boot log could be
-  captured from it, so the baud rate is unknown. There are most likely
-  unpopulated 0-Ohm resistors next to the header; bridging those should bring
-  the console to life.
-
-### Build target
-
-```
-make MACHINE=F7008_2_5
-```
-
-### LED wiring
-
-Measured pad to lamp map (`led_mux` index -> lamp):
-
-| Port | green lamp | yellow lamp |
-|------|-----------|-------------|
-| 1 | pad 0  | pad 1  |
-| 2 | pad 2  | pad 3  |
-| 3 | pad 4  | pad 5  |
-| 4 | pad 6  | pad 8  |
-| 5 | pad 9  | pad 10 |
-| 6 | pad 12 | pad 15 |
-| 7 | pad 18 | pad 21 |
-| 8 | pad 24 | pad 25 |
-
-Pads 7, 11, 13, 14, 16, 17, 19, 20, 22, 23, 26 and 27 do not drive an RJ45 lamp.
-
-The front panel is silkscreened `2.5G: Green / 10/100M: Yellow`, and the target
-follows it: the green lamp is on while the port is linked at 2.5G, the yellow
-lamp blinks while data is flowing.
-
-### PCB overview
-
-The board is marked `F7008-2.5GPOE-V1.2`.
-
-Top side:
-
-<img src="photos/F7008-2.5/PCB-top.jpg" width="600" />
-
-Bottom side:
-
-<img src="photos/F7008-2.5/PCB-bottom.jpg" width="600" />
-
-### Hardware notes
-
- 4 x `RT4802SNE` magnetics
- Unpopulated UART header footprint, next to the magnetics
- Power input 12V 1A, 180 x 84 x 29 mm metal case
@@ -1,39 +0,0 @@
-# FG-4GT-2SX_V2.0
-
-Following is documentation for unmanaged switch marked as `FG-4GT-2SX_V2.0`.
-
-Original software is running UART on 9600 baud rate.
-
-## Brands
-
-* Ruiying RY-4GT-2SX
-
-<img src="photos/FG-4GT-2SX_V2.0/RY-4GT-2SX_label.jpg" width="300" />
-
-## What works
-
- All four 2.5GBASE-T RJ45 ports at 10/100/1000/2500 Mbps  
- Both SFP ports supporting 1G, 2.5G and 10G modules 
- LEDs
-
-## PCB overview
-
-**Board markings**  
-
- Top silkscreen: FG-4GT-2SX_V2.0
-
-Front panel
-
-<img src="photos/FG-4GT-2SX_V2.0/chassis-front.jpg" width="300" />
-
-Top side
-
-<img src="photos/FG-4GT-2SX_V2.0/PCB-top.jpg" width="300" />
-
-Bottom
-
-<img src="photos/FG-4GT-2SX_V2.0/PCB-bottom.jpg" width="300" />
-
-## Power supply
-
-Input power is delivered via barell plug, `12V 1A` adapter was provided.
@@ -1,79 +0,0 @@
-# FG-8GT-1SX
-
-Following is documentation for unmanaged switch marked as `FG-8GT-1SX`.
-
-Original software is running UART on 9600 baud rate.
-
-Using SPI clamp in-board is the only method for initial installation.
-
-### Brands
-
-| Brand   | Type       | Managed | PCB        | Flash       | Chip RTL      |
-|---------|------------|---------|------------|-------------|---------------|
-| Ruiying | RY-8GT-1SX | No      | FG-8GT-1SX | GD25Q80ESIG | 8373N + 8224N |
-
-### What works
-
- All eight 2.5GBASE-T RJ45 ports at 10/100/1000/2500 Mbps
- SFP port with 1G/2.5G/10G modules
- LEDs
-
-### PCB overview
-
-**Board markings**
-
- Top silkscreen: FG-8GT-1SX
-
-Top side:
-
-<img src="photos/FG-8GT-1SX/PCB-top.jpg" width="600" />
-
-Bottom:
-
-<img src="photos/FG-8GT-1SX/PCB-bottom.jpg" width="600" />
-
-### Serial console
-
-The PCB has five unpopulated through-holes near the SoC, with a white rectangle surrouding them, labeled as `J18` and a triangle points to the square shaped first pin.
-
-This is where the "expected" UART header should be soldered at, with redundant 3V3 VCC, but also with missing 0Ω resistors between TX/RX and SoC, so simply soldering a header would not work. One need also add the missing resistors or solder the pads together, while making sure not connecting unrelated pads.
-
-Numbered from the triangle, the header pinout is:
-
-| Position | Signal | GPIO   | Status      |
-|----------|--------|--------|-------------|
-| 1        | GND    | GND    | Internal    |
-| 2        | TX     | GPIO31 | Unconnected |
-| 3        | RX     | GPIO32 | Unconnected |
-| 4        | 3V3    | -      | Internal    |
-| 5        | 3V3    | -      | Internal    |
-
-There're four resistor pads near the header.
-
-| Resistor ID | SoC Side    | Header Side |
-|-------------|-------------|-------------|
-| R1240       | TX / GPIO31 | Pin 2       |
-| R1243       | 3V3         | -           |
-| R1242       | 3V3         | Pin 3       |
-| R1241       | RX / GPIO32 | -           |
-
-To get TX working, solder a 0Ω resistor between the pads for R1240 or solder them together.
-
-For RX However, the designer certainly made a mistake, as the SoC-side lines to the resistor expected for Rx (R1242) and 3V3 (R1241) are swapped. For RX to work, the R1241 SoC side and R1242 header side shall be connected, so either:
-
- Solder: R1241 SoC side -> R1241 header side -> R1242 header side
- Jump wire: R1241 SoC side -> R1242 header side
-
-Be sure not to bring R1242 SoC side to the connection as that would wire Rx to 3v3.
-
-A complete working serial header should look like following on this PCB:
-
-<img src="photos/FG-8GT-1SX/Serial.png" width="600" />
-
- **Settings**: 115200 baud / 8N1 / 3.3V TTL
- Connect a USB-TTL adapter: adapter GND → pin 1, RX → pin 2, TX → pin 3
-
-### Power supply
-
-Input power is delivered via barell plug, `12V 1A` adapter was provided.
-
@@ -1,93 +0,0 @@
-# FOXNEO FNS-1200P
-
-RTL8372-based 4×2.5G PoE+ + 2×SFP+ unmanaged switch.
-
-Using SPI clamp in-board is the only method for initial installation.
-
-### Label specifications
-
- **Manufacturer**: FOXNEO
- **Model**: FNS-1200P
- **Ports**:
-  - 4 × RJ45: 10/100/1000/2500 Mbps with PoE+
-  - 2 × SFP+: 1G / 2.5G / 10G
-
-### What works
-
- All four 2.5GBASE-T RJ45 ports at 10/100/1000/2500 Mbps (PoE+ is not configurable via RTLPlayground)
- Both SFP+ ports supporting 1G, 2.5G and 10G modules
- LEDs: amber (2.5G) and green (1G/100M/10M) per copper port; combined link/act on SFP ports
-
-### PCB overview
-
-**Board markings**
- Top silkscreen: PCB-K0402W-U13-V2.0 / DIP-K0402WB-V2.0
-
-**Key components**
- U3: SPI NOR flash, 2 MiB
- U7: unpopulated SOP8 footprint — I2C bus (RTL8372 slave at 0x5c) is accessible from its pads, useful for register dumps
- S1: unpopulated slide switch footprint (three through-holes used as serial console)
-
-Front panel
-
-<img src="photos/FNS-1200P/chassis-front.jpg" width="400" />
-
-Top side (PCB)
-
-<img src="photos/FNS-1200P/PCB-top.jpg" width="300" />
-
-### Port layout
-
-| Front panel position | Logical port | Physical port | Type    |
-|----------------------|--------------|---------------|---------|
-| SFP left             | 8            | 5             | SFP+    |
-| RJ45 1               | 4            | 1             | Copper  |
-| RJ45 2               | 5            | 2             | Copper  |
-| RJ45 3               | 6            | 3             | Copper  |
-| RJ45 4               | 7            | 4             | Copper  |
-| SFP right            | 3            | 6             | SFP+    |
-
-### Serial console
-
-The PCB has three unpopulated through-holes intended for a slide switch, directly connected to UART0.
-Numbered from the left (SFP port side), the pinout is:
-
-| Position (left→right) | Signal | GPIO                     |
-|-----------------------|--------|--------------------------|
-| 1 (leftmost)          | RX     | GPIO32\_UART0\_RX (32)   |
-| 2 (middle)            | GND    | GND                      |
-| 3 (rightmost)         | TX     | GPIO31\_UART0\_TX (31)   |
-
- **Settings**: 115200 baud / 8N1 / 3.3V TTL
- Connect a USB-TTL adapter: adapter TX → pin 1, GND → pin 2, adapter RX → pin 3
-
-### LED configuration
-
-Copper ports use LED SET0, SFP ports use LED SET1.
-
-| SET  | LED0                                             | LED2                                              |
-|------|--------------------------------------------------|---------------------------------------------------|
-| SET0 | Amber — lights on 2.5G link                      | Green — lights on 1G / 100M / 10M link            |
-| SET1 | All speeds — lights on any link with activity    | —                                                 |
-
-LED pad to physical port mapping:
-
-| GPIO pads | Port                    |
-|-----------|-------------------------|
-| GPIO8–11  | Physical port 5 (left SFP)  |
-| GPIO12–14 | Physical port 1 (RJ45 1)    |
-| GPIO15–17 | Physical port 2 (RJ45 2)    |
-| GPIO18–20 | Physical port 3 (RJ45 3)    |
-| GPIO21–23 | Physical port 4 (RJ45 4)    |
-| GPIO24–27 | Physical port 6 (right SFP) |
-
-### SFP GPIO assignments
-
-| SFP              | pin\_detect (ModAbs)        | pin\_los               | SerDes | I2C SDA              | I2C SCL                  |
-|------------------|-----------------------------|------------------------|--------|----------------------|--------------------------|
-| Left (logical 8) | GPIO30\_ACL\_BIT3\_EN       | GPIO37                 | SDS1   | GPIO39\_I2C\_SDA4    | GPIO40\_I2C\_SCL3\_MDC1  |
-| Right (logical 3)| GPIO50\_I2C\_SCL2\_UART1\_TX | GPIO51\_I2C\_SDA2\_UART1\_RX | SDS0 | GPIO41\_I2C\_SDA3\_MDIO1 | GPIO40\_I2C\_SCL3\_MDC1 |
-
-GPIO assignments were verified by observing GPIO state changes during SFP module insertion/removal
-and cross-checked against an original firmware register dump.
-`pin_tx_disable` is GPIO\_NA on both ports (original firmware keeps all GPIOs as inputs).
@@ -1,75 +0,0 @@
-# Hasivo S1100WP-8GT-1SX-SE
-
-RTL8373-based 8×2.5G PoE + 1×SFP switch.
-
-### Label specifications
-
- **Manufacturer**: Hasivo
- **Model**: S1100WP-8GT-1SX-SE
- **Ports**:
-  - 8 × RJ45: 10/100/1000/2500 Mbps with PoE
-  - 1 × SFP: 1G / 2.5G / 10G
- **Power input**: DC 52V 2.5A
- **Stock firmware defaults**: IP 192.168.0.1, user/password `admin`/`admin`
-
-### What works
-
- All eight 2.5GBASE-T RJ45 ports at 10/100/1000/2500 Mbps (PoE is not configurable via RTLPlayground)
- SFP port supporting 1G, 2.5G and 10G modules
- LEDs: green (2.5G) and amber (1G/100M/10M) per copper port; combined link/act on the SFP port
-
-### Photos
-
-Front panel:
-
-<img src="photos/HASIVO_S1100WP-8GT-1SX-SE/front.jpg" width="600" />
-
-Label:
-
-<img src="photos/HASIVO_S1100WP-8GT-1SX-SE/label.jpg" width="600" />
-
-### PCB overview
-
-Top side:
-
-<img src="photos/HASIVO_S1100WP-8GT-1SX-SE/pcb_top.jpg" width="600" />
-
-Bottom side:
-
-<img src="photos/HASIVO_S1100WP-8GT-1SX-SE/pcb_bottom.jpg" width="600" />
-
-### Port layout
-
-| Logical port | Physical port | Type   |
-|--------------|---------------|--------|
-| 1-8          | 1-8           | Copper |
-| 9            | 9             | SFP    |
-
-### LED configuration
-
-Copper ports use LED SET0, the SFP port uses LED SET1.
-
-| SET  | LED0                                          | LED2                                                 |
-|------|-----------------------------------------------|------------------------------------------------------|
-| SET0 | Green — lights on 2.5G link with activity     | Amber — lights on 1G / 100M / 10M link with activity |
-| SET1 | All speeds — lights on any link with activity | —                                                    |
-
-### SFP GPIO assignments
-
-| SFP (logical 9) | pin_detect (ModAbs) | pin_los | pin_tx_disable | SerDes | I2C SDA         | I2C SCL             |
-|-----------------|---------------------|---------|----------------|--------|-----------------|---------------------|
-| SFP             | GPIO30_ACL_BIT3_EN  | GPIO37  | GPIO_NA        | SDS1   | GPIO39_I2C_SDA4 | GPIO40_I2C_SCL3_MDC1 |
-
-### Machine configuration
-
- `reset_pin`: GPIO54_ACL_BIT2_EN
- High LEDs (pads 27-29): mux = `LED_27 | LED_28_SYS | LED_29`, enable = `LED_28_SYS | LED_29`
-
-### PoE
-
-The 8 copper ports support PoE powered by a DC 52V 2.5A input. Power management is handled by two HS104PTI chipsets over I2C (GPIO47_I2C_SDA0, GPIO46_I2C_SCL0):
-
-* Chip 1 (I2C address 0x1A): 2.5G Ports 1–4
-* Chip 2 (I2C address 0x2A): 2.5G Ports 5–8
-
-Note: The current implementation does not yet support PoE management. Consequently, PoE currently operates in standalone mode without software control.
@@ -1,36 +0,0 @@
-# Hisource Hi-K0801WS
-
-Following is documentation for unmanaged switch marked as `Hi-K0801WS`.
-
-Using SPI clamp in-board is the only method for initial installation.
-
-### Label specifications
-
- **Name**: 2.5G Ethernet Switch  
- **Model**: Hi-K0801WS  
- **Ports**:  
-  - 8 × RJ45: 10/100/1000/2500 Mbps  
-  - 1 × SFP: 1000 / 2500 / 10000 Mbps  
-
-### What works (expected from label + similar devices)
-
- All eight 2.5GBASE-T RJ45 ports at 10/100/1000/2500 Mbps  
- SFP port supporting 1G, 2.5G and 10G modules 
- LEDs
-
-### PCB overview
-
-**Board markings**  
- Top silkscreen: PCB-KO801W-V2.0 / DIP-KO801WS-V2.0  
-
-Top side
-
-<img src="photos/K0801W-V2.0-unmanaged\PCB-top.jpg" width="300" />
-
-Bottom
-
-<img src="photos/K0801W-V2.0-unmanaged\PCB-bottom.jpg" width="300" />
-
-## Power supply
-
-Input power is delivered via barell plug, `12V 1A` adapter was provided.
@@ -1,64 +0,0 @@
-# Lianguo HYWS-SGT0108S
-
-Following is documentation for unmanaged switch marked as `HYWS-SGT0108S`.
-
-Original software is running UART on 9600 baud rate. Output is very minimal.
-
-Using SPI clamp in-board is the only method for initial installation and update.
-
-Stock flash chip is 512KB in size. Consider replacing for update through Web UI.
-
- Header for uart is clearly identified.
- The red LED act as a powered-on LED.
- There is no SYS LED.
- There is a footprint for a Reset button. Unpopulated. Unclear if routed back to RTL8373.
-
-### Label specifications
-
- **Name**: 2.5G Ethernet Switch 8+1
- **Model**: HYWS-SGT0108S
- **Ports**:  
-  - 8 × RJ45: 10/100/1000/2500 Mbps  
-  - 1 × SFP: 1000 / 2500 / 10000 Mbps  
-
-### What works
-
- All eight 2.5GBASE-T RJ45 ports at 10/100/1000/2500 Mbps  
- SFP port supporting 1G, 2.5G and 10G modules 
- RJ45 LEDs (Blue+White)
- SFP Single LED (Blue)
-
-### Assembled unit
-
-Top side
-
-<img src="photos/HYWS-SGT0108S-unmanaged\Assembled-top.jpg" width="300" />
-
-Front
-
-<img src="photos/HYWS-SGT0108S-unmanaged\Assembled-front.jpg" width="300" />
-
-Bottom
-
-<img src="photos/HYWS-SGT0108S-unmanaged\Assembled-bottom.jpg" width="300" />
-
-### PCB overview
-
-**Board markings**  
- Top silkscreen: 2G5F_20G_V1.01 / 2023-09-28  
-
-Top side
-
-<img src="photos/HYWS-SGT0108S-unmanaged\PCB-top.jpg" width="300" />
-
-Bottom
-
-<img src="photos/HYWS-SGT0108S-unmanaged\PCB-bot.jpg" width="300" />
-
-Original SPI Flash Chip
-
-<img src="photos/HYWS-SGT0108S-unmanaged\og_spi_flash.jpg" width="300" />
-
-## Power supply
-
-Input power is delivered via barell plug, `12V 1A` adapter was provided.
@@ -1,23 +0,0 @@
-# K0501W V2.0
-
-This board appears for example in the Davuaz Da-K6501W switch.
-
-The general design of the board is similar to Hi-K0402WS V3.0.
-However, there are several differences:
- One SFP port is replaced by a RTL8221B 2.5G PHY
- Only one LED is populated for the SFP port
- No mode switch and only one flash chip
- Older design using RTL8372 instead of RTL8372N (which also means different GPIO and LED configuration)
- Like earlier versions of the K0402W(S) board, there is no UART
-
-All ports and LEDs are supported.
-Installation is possible using a flash programmer.
-The BoyaMicro 25Q16BSSIG flash chip is supported by flashprog with chip name "B.25D16AS/BY25Q16BS/BY25Q16ES".
-
-## PCB pictures
-
-The board is marked `PCB-K0501W-V2.0 DIP-K0501WS-V2.0`.
-
-<img src="photos/K0501W_V2_0/pcb-top.jpg" width="300" />
-
-<img src="photos/K0501W_V2_0/pcb-bottom.jpg" width="300" />
@@ -1,93 +0,0 @@
-# Keeplink KP-9000-6XH-X2 / KP-9000-6XHML-X2
-
-Following is documentation for switches marked as `KP-9000-6XH-X2` or
-`KP-9000-6XHML-X2`.
-
-Using SPI clamp in-board is the only method for initial installation.
-
-### Label specifications
-
- **Name**: 4X 2.5G RJ45 Port + 2 X 10G SFP+ Port  
- **Model**: KP-9000-6XH-X2 / KP-9000-6XHML-X2
- **Ports**:  
-  - 4 × RJ45: 10/100/1000/2500 Mbps  
-  - 2 × SFP+: 1000 / 2500 / 10000 Mbps  
-
-### Machine target
-
-These devices exist with different PCB revisions. Select the machine target by
-the PCB silkscreen, not by the label on the case. The `6XH` / `6XHML`
-distinction appears to be a stock firmware, SKU or label difference, not a
-reliable indicator of PCB wiring. The PCB revision defines the hardware layout.
-
-| PCB silkscreen | Known labels / devices | Recommended machine target | Equivalent target | Legacy target |
-| --- | --- | --- | --- | --- |
-| `2M-PCB43-V1.1` | Mokerlink 2G040210GSM web-managed 4+2 switch | `MACHINE_KP_9000_6XHML_X2_V1_1` | `MACHINE_KP_9000_6XH_X2_V1_1` | `MACHINE_KP_9000_6XHML_X2` |
-| `2M-PCB43-V1.2` | `KP-9000-6XHML-X2` | `MACHINE_KP_9000_6XHML_X2_V1_2` | `MACHINE_KP_9000_6XH_X2_V1_2` | `MACHINE_KP_9000_6XHML_X2` |
-| `2M-PCB43-V2.1` | `KP-9000-6XH-X2`, `KP-9000-6XHML-X2` | `MACHINE_KP_9000_6XH_X2_V2_1` or `MACHINE_KP_9000_6XHML_X2_V2_1` | same V2.1 layout | `MACHINE_KP_9000_6XH_X2` |
-
-The V1.1 and V1.2 boards currently use the same V1.x GPIO, SFP, port and LED
-layout. The V2.1 board uses a different V2.1 layout with custom LED muxing.
-Legacy targets are preserved for compatibility with already-tested devices, but
-new builds should prefer the explicit PCB-revision targets.
-
-### What works
-
- All four 2.5GBASE-T RJ45 ports at 10/100/1000/2500 Mbps
- SFP port with 10G modules 
- LEDs
- untested due to missing Hardware: SFP+ ports equipped with 1G or 2.5G SFPs.
-
-### Hardware overview: 2M-PCB43-V2.1
-
-Front side:
-
-<img src="photos/2M-PCB43-V2.1-unmanaged/KP-9000-6XH-X2-front.jpg" width="600" />
-
-Label:
-
-<img src="photos/2M-PCB43-V2.1-unmanaged/KP-9000-6XH-X2-label.jpg" width="600" />
-
-
-
-### PCB overview
-
-**Board markings**  
- Top silkscreen: 2M-PCB43-V2.1
-
-Top side
-
-<img src="photos/2M-PCB43-V2.1-unmanaged/2M-PCB43-V2.1-top.jpg" width="600" />
-
-Bottom
-
-<img src="photos/2M-PCB43-V2.1-unmanaged/2M-PCB43-V2.1-bottom.jpg" width="600" />
-
-### Hardware overview: 2M-PCB43-V1.1 / V1.2
-
-The V1.1 board has been reported in the Mokerlink 2G040210GSM web-managed 4+2
-switch. The V1.2 board has been seen in managed `KP-9000-6XHML-X2` devices.
-Both use the same V1.x layout.
-
-Label:
-
-<img src="photos/KP-9000-6XHML-X2/label.jpg" width="600" />
-
-Top side:
-
-<img src="photos/KP-9000-6XHML-X2/pcb_top.jpg" width="600" />
-
-Bottom:
-
-<img src="photos/KP-9000-6XHML-X2/pcb_bottom.jpg" width="600" />
-
-## Reset Button
-
-There's an unpopulated Reset button on the front left side of the PCB.
-It can easily be soldered, you'll need an 4.5mmx4.5mm 90° button switch with a 3-pin footprint.
-I got mine here: https://de.aliexpress.com/item/1005007295346702.html
-The front case has already the hole in the metal case, you just have to punch a hole through the foil.
-
-## Power supply
-
-Input power is delivered via barell plug, `12V 1A` adapter was provided.
@@ -1,122 +0,0 @@
-# ONT-S207CW-62TS-SE / Binardat 2G06-04210GSM / Binardat 2G06-04210GS
-
-## Overview
-
-ONT-S207CW-62TS-SE, Binardat 2G06-04210GSM (managed), and Binardat 2G06-04210GS (unmanaged) are **switches with identical hardware**:
- **CPU:** RTL8372N (confirmed via serial: "Detecting CPU: RTL8372N")
- **Flash:** GD25Q128E (16MB)
- **Ports:** 4x 2.5G RJ45 + 2x 10G SFP+
- **Console:** 115200 baud (RTLPlayground firmware) / 9600 baud (stock firmware)
-
-**Note:** These devices are **RTL8372N-based** with **LAN ports mounted upside-down on the PCB**, requiring a custom configuration. The `MACHINE_ONT_S207CW_62TS_SE` definition uses a **custom configuration** with:
- Corrected port mapping (physical ports 1-4 = RJ45, 5-6 = SFP)
- Optimized LED sets for different port wiring (RJ45 Ports 1-2 have reversed LED wiring)
- Custom LED mux configuration
-
-## Device Photos
-
-### Binardat 2G06-04210GSM
-
-**Front View:**
-<img src="photos/ONT-S207CW-Binardat-2G06-04210GSM/binardat-2g06-04210gsm-front.jpg" width="400" />
-
-**Back View:**
-<img src="photos/ONT-S207CW-Binardat-2G06-04210GSM/binardat-2g06-04210gsm-back.jpg" width="400" />
-
-**PCB View:**
-<img src="photos/ONT-S207CW-Binardat-2G06-04210GSM/binardat-2g06-04210gsm-pcb.jpg" width="400" />
-
-*Photos courtesy of [andreas5232](https://github.com/andreas5232) from [emesix/ONT-S207CW-62TS-SE#1](https://github.com/emesix/ONT-S207CW-62TS-SE/issues/1)*
-
-## Hardware Specification
-
-| Feature | Value |
-|---|---|
-| **CPU** | RTL8372N |
-| **Flash** | GD25Q128E (16MB) |
-| **RAM** | Integrated in RTL8372N |
-| **RJ45 Ports** | 4x 2.5GBase-T (Ports 1-4) |
-| **SFP+ Ports** | 2x 10G (Ports 5-6) |
-| **Console** | UART (115200 baud for RTLPlayground, 9600 baud for stock) |
-| **Stock Web UI IP** | 192.168.2.1 |
-| **Loader Mode IP** | 192.168.10.247 |
-
-## Port Layout
-
-```
-┌─────────────────────────────────────────────┐
-│  ┌─────┐ ┌─────┐ ┌─────┐ ┌─────┐   ┌─────┐ ┌─────┐  │
-│  │RJ45 │ │RJ45 │ │RJ45 │ │RJ45 │   │SFP+ │ │SFP+ │  │
-│  │  1  │ │  2  │ │  3  │ │  4  │   │  5  │ │  6  │  │
-│  └─────┘ └─────┘ └─────┘ └─────┘   └─────┘ └─────┘  │
-│                                                     │
-│  [System LEDs]                                      │
-└─────────────────────────────────────────────┘
-```
-
-## LED Behavior
-
-### RJ45 Ports (Physical 1-4)
-
-| LED Color | Speed |
-|---|---|
-| **Green** | 2.5G |
-| **Orange** | 1G / 100M / 10M |
-| **Off** | No link |
-
-### SFP+ Ports (Physical 5-6)
-
-| LED Color | Speed |
-|---|---|
-| **Green** | 10G |
-| **Orange** | 2.5G / 1G |
-| **Off** | No link / No SFP module |
-
-## Port to Logical Mapping
-
-Custom mapping for ONT-S207CW-62TS-SE:
-
-| Physical Port | Logical Port | Type | LED Set |
-|---|---|---|---|
-| 1 | 7 | RJ45 | 2 |
-| 2 | 6 | RJ45 | 2 |
-| 3 | 5 | RJ45 | 0 |
-| 4 | 4 | RJ45 | 0 |
-| 5 | 3 | SFP+ (SDS0) | 3 |
-| 6 | 8 | SFP+ (SDS1) | 3 |
-
-**Note:** Ports 1-2 (RJ45) have reversed LED wiring and use LED-Set 2. SFP Ports 5-6 use LED-Set 3 to account for wiring differences.
-
-## Flashing Instructions
-
-See the [README.md](../../README.md) for general flashing instructions.
-
-## Stock Firmware Information
-
-| Property | Value |
-|---|---|
-| **Default IP** | 192.168.2.1 (ONT) / 192.168.10.247 (Loader Mode) |
-| **Default Login** | admin/admin (may vary by OEM) |
-| **Console Baud** | 9600 (stock) / 115200 (RTLPlayground) |
-| **CPU String** | "RTL8372N" |
-| **Loader Mode IP** | 192.168.10.247 |
-
-## Configuration Details
-
- **CPU:** RTL8372N
- **SFP:** SDS0 on logical port 3 (GPIO37), SDS1 on logical port 8 (GPIO38)
- **Port Mapping:** Physical 1-4 → Logical 7-4, Physical 5-6 → Logical 3,8
- **LED Wiring:** RJ45 Ports 1-2 and SFP Port 6 have reversed LED pins (orange/green swapped)
- **LED Sets:** Set 0 for RJ45 Ports 3-4, Set 1 unused, Set 2 for RJ45 Ports 1-2, Set 3 for SFP Ports 5-6
-
-## Notes
-
- ONT-S207CW-62TS-SE, Binardat 2G06-04210GSM (managed), and Binardat 2G06-04210GS (unmanaged) are **RTL8372N-based** with **LAN ports mounted upside-down on the PCB**
- Web UI shows correct physical port order (1-2-3-4 for RJ45, 5-6 for SFP)
- Loader Mode always remains accessible at `192.168.10.247` for recovery
- Serial console: 9600 baud (stock) → 115200 baud (RTLPlayground)
-
-## References
-
- [GitHub Issue: emesix/ONT-S207CW-62TS-SE#1](https://github.com/emesix/ONT-S207CW-62TS-SE/issues/1) - Original photos and discussion
- [PR: logicog/RTLPlayground#465](https://github.com/logicog/RTLPlayground/pull/465) - Feedback and improvements
@@ -1,53 +0,0 @@
-# IG108
-
-Following is documentation for unmanaged switch marked as `IG108`.
-
-Original software is running UART on 9600 baud rate.
-
-Using SPI clamp in-board is the only method for initial installation.
-
-### Brands
-
-| Brand   | Type       | Managed | PCB        | Flash       | Chip RTL      |
-|---------|------------|---------|------------|-------------|---------------|
-| Goalake | IG108      | No      | PB-2132    | cFeon Q32A  | 8373N + 8224N |
-| Netcore | GS9        | No      | PB-2132    | cFeon Q32A  | 8373N + 8224N |
-
-### What works
-
- All eight 2.5GBASE-T RJ45 ports at 10/100/1000/2500 Mbps
- SFP port with 1G/2.5G/10G modules
- LEDs
-
-### PCB overview
-
-**Board markings**
-
- Top silkscreen: PB-2132
-
-Front Goalake:
-
-<img src="photos/PB-2132/case.jpg" width="600" />
-
-Label Goalake: 
-
-<img src="photos/PB-2132/label.jpg" width="600" />
-
-Top side:
-
-<img src="photos/PB-2132/PCB-top.jpg" width="600" />
-
-Bottom:
-
-<img src="photos/PB-2132/PCB-bottom.jpg" width="600" />
-
-### Serial console
-
-The PCB has unpopulated through-holes near the SFP Port, with description of each pin, works out of the box.
-
- **Settings**: 115200 baud / 8N1 / 3.3V TTL
-
-### Power supply
-
-Input power is delivered via barell plug, `12V 1A` adapter was provided.
-
@@ -1,97 +0,0 @@
-Hisource Hi-K0402WS V2
-
-RTL8372-based 4×2.5G + 2×SFP+ unmanaged switch.
-
-Using SPI clamp in-board is the only method for initial installation.
-
-### Label specifications
-
- **Manufacturer**: HISOURCE
- **Model**: Hi-K0402WS V2
- **Ports**:
-  - 4 × RJ45: 10/100/1000/2500 Mbps
-  - 2 × SFP+: 1G / 2.5G / 10G
-
-### What works
-
- All four 2.5GBASE-T RJ45 ports at 10/100/1000/2500 Mbps
- Both SFP+ ports supporting 1G, 2.5G and 10G modules
- LEDs: amber (2.5G) and green (1G/100M/10M) per copper port; combined link/act on SFP ports
-
-### PCB overview
-
-**Board markings**
- PCB-K0402WS-V2.0
- DIP-K0402WS-V2.0
-
-**Key components**
- U1: SPI NOR flash, 2 MiB
- S1: unpopulated slide switch footprint (three through-holes used as serial console)
-
-Front panel
-
-<img src="photos/PCB-K0402WS-V2.0/chassis-front.jpg" width="400" />
-
-Bottom label
-
-<img src="photos/PCB-K0402WS-V2.0/chassis-bottom.jpg" width="400" />
-
-Top side (PCB)
-
-<img src="photos/PCB-K0402WS-V2.0/PCB-top.jpg" width="300" />
-
-### Port layout
-
-| Front panel position | Logical port | Physical port | Type    |
-|----------------------|--------------|---------------|---------|
-| SFP left             | 8            | 5             | SFP+    |
-| RJ45 1               | 4            | 1             | Copper  |
-| RJ45 2               | 5            | 2             | Copper  |
-| RJ45 3               | 6            | 3             | Copper  |
-| RJ45 4               | 7            | 4             | Copper  |
-| SFP right            | 3            | 6             | SFP+    |
-
-### Serial console
-
-The PCB has three unpopulated through-holes intended for a slide switch, directly connected to UART0.
-Numbered from the left (SFP port side), the pinout is:
-
-| Position (left→right) | Signal | GPIO                     |
-|-----------------------|--------|--------------------------|
-| 1 (leftmost)          | RX     | GPIO32\_UART0\_RX (32)   |
-| 2 (middle)            | GND    | GND                      |
-| 3 (rightmost)         | TX     | GPIO31\_UART0\_TX (31)   |
-
- **Settings**: 115200 baud / 8N1 / 3.3V TTL
- Connect a USB-TTL adapter: adapter TX → pin 1, GND → pin 2, adapter RX → pin 3
-
-### LED configuration
-
-Copper ports use LED SET0, SFP ports use LED SET1.
-
-| SET  | LED0                                             | LED2                                              |
-|------|--------------------------------------------------|---------------------------------------------------|
-| SET0 | Amber — lights on 2.5G link                      | Green — lights on 1G / 100M / 10M link            |
-| SET1 | All speeds — lights on any link with activity    | —                                                 |
-
-LED pad to physical port mapping:
-
-| GPIO pads | Port                    |
-|-----------|-------------------------|
-| GPIO8–11  | Physical port 5 (left SFP)  |
-| GPIO12–14 | Physical port 1 (RJ45 1)    |
-| GPIO15–17 | Physical port 2 (RJ45 2)    |
-| GPIO18–20 | Physical port 3 (RJ45 3)    |
-| GPIO21–23 | Physical port 4 (RJ45 4)    |
-| GPIO24–27 | Physical port 6 (right SFP) |
-
-### SFP GPIO assignments
-
-| SFP              | pin\_detect (ModAbs)        | pin\_los               | SerDes | I2C SDA              | I2C SCL                  |
-|------------------|-----------------------------|------------------------|--------|----------------------|--------------------------|
-| Left (logical 8) | GPIO30\_ACL\_BIT3\_EN       | GPIO37                 | SDS1   | GPIO39\_I2C\_SDA4    | GPIO40\_I2C\_SCL3\_MDC1  |
-| Right (logical 3)| GPIO50\_I2C\_SCL2\_UART1\_TX | GPIO51\_I2C\_SDA2\_UART1\_RX | SDS0 | GPIO41\_I2C\_SDA3\_MDIO1 | GPIO40\_I2C\_SCL3\_MDC1 |
-
-GPIO assignments were verified by observing GPIO state changes during SFP module insertion/removal
-and cross-checked against an original firmware register dump.
-`pin_tx_disable` is GPIO\_NA on both ports (original firmware keeps all GPIOs as inputs).
@@ -1,79 +0,0 @@
-# PCB-K0402WS-V3.0
-
-Following is documentation for a variety of unmanaged switch internally marked as `PCB-K0402WS-V3.0`. They are sold under many brands.
-
-Original software is running UART on 9600 baud rate.
-
-Note during opening the device: there might be a hidden 5th screw on the back
-of the device just above the big label, might be covered by a QC sticker.
-
-### Brands
-
-* Hisource Hi-K0402WS
-
-<img src="photos/PCB-K0402WS-V3.0/HiSource_HI-K0402WS.jpg" width="300" />
-
-* Ztyuav Z-QWYT0402
-
-<img src="photos/PCB-K0402WS-V3.0/Ztyuav_Z-QWYT0402.jpg" width="300" />
-
-<img src="photos/PCB-K0402WS-V3.0/Ztyuav_Z-QWYT0402_label.jpg" width="300" />
-
-* Siscolink SL-G0402F
-
-<img src="photos/PCB-K0402WS-V3.0/Siscolink SL-G0402F.jpg" width="300"/>
-### Programming
-
-Using SPI clamp in-board is the only method for initial installation.
-
-The board has two flash chips `BY25Q16BS` with 16M-bit size. The front switch, switches between the two flash chips.
-These can be programed independently by using said switch - so it is e.g. possible to run the original and new firmware in parallel.
-The switch actually controls the HOLD line of each flash chip, and toggling the switch results in a reboot.
-
-If the programming clip keeps HOLD not connected, the flashing will commence on whatever the switch selected, regardless on which chip was clipped.
-
-For the initial flash (at least with flashrom), the bin file produced by the build is much smaller than the flash chip, it is suggested to pad the file to keep flashrom happy: `truncate -s 2097152 rtlplayground-*-PCB_K0402WS_V3.bin`. Note: do not then proceed to use this resulting padded file for the web flashing (as it bricks the device), use the original unpadded .bin.
-
-### What works (expected from label + similar devices)
-
- All four 2.5GBASE-T RJ45 ports at 10/100/1000/2500 Mbps  
- Both SFP ports supporting 1G, 2.5G and 10G modules 
- LEDs
-
-### PCB overview
-
-**Board markings**  
- Top silkscreen: PCB-KO4022W-V3.0 / DIP-KO4022WS-V3.0  
-
-Top side
-
-<img src="photos/PCB-K0402WS-V3.0/PCB-top.jpg" width="300" />
-
-Bottom
-
-<img src="photos/PCB-K0402WS-V3.0/PCB-bottom.jpg" width="300" />
-
-### T2, serial console
-
-| `J2` pin | Signal      |
-| -------- | ----------- |
-| 1        | 3V3         |
-| 2        | RX (Input) |
-| 3        | TX (Output)  |
-| 4        | GND         |
-
-
-## Power supply
-
-Input power is delivered via barell plug, `12V 1A` adapter was provided.
-Board has two supply rails. `0.95` and `3.3` volt.
-
-### `0.95` Core Voltage
-
-Voltage is made by a `Techcode TD1720` .
-
-### `3.3` Voltage
-
-Voltage is created by chip marked as `Techcode TD1720`.
-
-**There seems to have been a miscalculation when choosing the inductor and the device is ~25% more efficient with an 5V power supply.**
@@ -1,43 +0,0 @@
-# Steamemo IG204-V1
-
-Following is documentation for unmanaged switch marked as `IG204-V1`.
-
-Using SPI clamp in-board is the only method for initial installation.
-
-### Label specifications
-
- **Name**: 2.5G Ethernet Switch  
- **Model**: IG204 V1
- **Ports**:  
-  - 4 × RJ45: 10/100/1000/2500 Mbps  
-  - 2 × SFP: 1000 / 2500 / 10000 Mbps  
-
-### What works (expected from label + similar devices)
-
- Four 2.5GBASE-T RJ45 ports at 10/100/1000/2500 Mbps  
- Two SFP ports supporting 1G, 2.5G and 10G modules 
- LEDs
-
-### PCB overview
-
-**Board markings**  
- Top silkscreen: PB-2131
-
-
-Top side
-
-<img src="photos/STEAMEMO_IG204_V1/PCB-top.jpg" width="600" />
-
-### Connectors
-### T7, serial console
-
-| `T7` pin | Signal      |
-| -------- | ----------- |
-| 1        | TX (Output) |
-| 2        | GND         |
-| 3        | RX (Input)  |
-| 4        | 3V3         |
-
-### Power supply
-
-Input power is delivered via barell plug, `12V 1A` adapter was provided.
@@ -1,61 +0,0 @@
-# SWTG018AS-A V2.0
-## Brands
-| Brand   | Type             |Managed| PCB              | Flash           | Chip RTL      |
-|---------|------------------|-------|------------------|-----------------|---------------|
-| Ampcom  | SWTG018AS-A V2.0 | No    | SWTG018AS-A V2.0 | 2MB             | 8273N + 8224N |
-| Horaco  | HC-SWTGW218AS-A  | Yes   | SWTG018AS-A V2.0 | 2MB(25Q16JVSIQ) | 8273N + 8224N |
-| GoodTop | GT-ST018M        | Yes   | SWTG018AS-A V2.0 | ?               | 8273N + 8224N |
-
-
-The following is a documentation for the unmanaged switch marked as `SWTG018AS-A V2.0`.
-It is e.g. sold under the Ampcom brand, but no branh-markings are found on the device.
-
-The original software is running UART on 9600 baud rate. 
-
-Using a SOIC clamp in-board is the only method for initial installation.
-
-The board has a single flash chips `BS` with 4M-bit size. The front switch, switches between the two flash chips.
-These can be programed independently by using said switch - so it is e.g. possible to run the original and new firmware in parallel.
-
-### Label specifications
-
- **Name**: 9-Ports 2.5G Ethernet Switch
- **Ports**:
-  - 8 × RJ45: 10/100/1000/2500 Mbps
-  - 1 × SFP+: 1000 / 2500 / 10000 Mbps
- **Power**: 12V DC, 1A barrel connector 
-
-<img src="photos/SWTG018AS_A_V_2_0/label.jpg" width="300" />
-
-### What works
-The device is fully supported:
- All 8 2.5GBASE-T RJ45 ports work at 10/100/1000/2500 Mbps
- The SFP+ port supports 1G, 2.5G and 10G modules 
- LEDs work with the same indiciations as the OEM firmware
-
-### PCB overview
-
-**Board markings**
- Top silkscreen: SWTG018AS-A-V2.0.1_19649
-
-Top side
-
-<img src="photos/SWTG018AS_A_V_2_0/pcb_top.jpg" width="300" />
-
-Bottom
-
-<img src="photos/SWTG018AS_A_V_2_0/pcb_bottom.jpg" width="300" />
-
-### J1, serial console
-
-| `J1` pin | Signal      |
-| -------- | ----------- |
-| 1        | 3V3         |
-| 2        | GND         |
-| 3        | RX (Input) |
-| 4        | TX (Output)  |
-
-
-## Power supply
-
-Input power is delivered via barell plug, `12V 1A` adapter was provided.
@@ -1,44 +0,0 @@
-### SWTG024AS-A-V2.0.1_4C_2SFP
-It is highly similar to SWTG024AS-V2.0, with the only difference being the GPIO configuration for the SFP port.
-
-## Brands
-|Brand|Type|Managed|PCB|Flash|Chip RTL|
-|---|---|---|---|---|---|
-| Horaco | ZX-SG4T2 |  | PCB-SWTG024AS-A-V2.0.1_19650 | P25D40SH | ??? |
-| GoodTop | GT-ST024M | Yes | PCB-SWTG024AS-A-V2.0.1 | 2M | ??? |
-
-### Label specifications
-
- **Name**: 
- **Ports**:
-  - 4 × RJ45: 10/100/1000/2500 Mbps
-  - 2 × SFP+: 1000 / 2500 / 10000 Mbps
-
-<img src="photos/SWTG024AS-A-V2_0_1_19650/horaco-zx-sg4t2-label.jpg" width="300" />
-
-### What works
-The device is fully supported:
- ALL 2.5GBASE-T RJ45 ports work at 10/100/1000/2500 Mbps
- The SFP+ port supports 1G, 2.5G and 10G modules 
-
-### PCB overview
-
-**Board markings**
- Top silkscreen: PCB-SWTG024AS-A-V2.0.1_19650
-
-Top side
-
-<img src="photos/SWTG024AS-A-V2_0_1_19650/horaco-zx-sg4t2-pcb-top.jpg" width="300" />
-
-Bottom
-
-<img src="photos/SWTG024AS-A-V2_0_1_19650/horaco-zx-sg4t2-pcb-bottom.jpg" width="300" />
-
-### J1, serial console
-
-| `J1` pin | Signal      |
-| -------- | ----------- |
-| 1        | 3V3         |
-| 2        | GND         |
-| 3        | RX (Input)  |
-| 4        | TX (Output) |
@@ -1,44 +0,0 @@
-### SWTG024AS-A-V2.0.1_5C_1SFP
-It is highly similar to SWTG024AS-V2.0, with the only difference being the GPIO configuration for the SFP port.
-
-## Brands
-|Brand|Type|Managed|PCB|Flash|Chip RTL|
-|---|---|---|---|---|---|
-| Horaco | HC-SWTGW215AS |  | PCB-SWTG024AS-A-V2.0.1_19650 | W25Q16JV | 8272N |
-
-### Label specifications
-
- **Name**: 
- **Ports**:
-  - 5 × RJ45: 10/100/1000/2500 Mbps
-  - 1 × SFP+: 1000 / 2500 / 10000 Mbps
-
-<!-- <img src="" width="300" /> -->
-
-### What works
-The device is fully supported:
- ALL 2.5GBASE-T RJ45 ports work at 10/100/1000/2500 Mbps
- The SFP+ port supports 1G, 2.5G and 10G modules 
- LEDs work with the same indiciations as the OEM firmware
-
-### PCB overview
-
-**Board markings**
- Top silkscreen: PCB-SWTG024AS-A-V2.0.1_19650
-
-Top side
-
-<!-- <img src="" width="300" /> -->
-
-Bottom
-
-<!-- <img src="" width="300" /> -->
-
-### J1, serial console
-
-| `J1` pin | Signal      |
-| -------- | ----------- |
-| 1        | 3V3         |
-| 2        | GND         |
-| 3        | RX (Input)  |
-| 4        | TX (Output) |
@@ -1,49 +0,0 @@
-### SWTG024AS-V2.0
-
-## Brands
-|Brand|Type|Managed|PCB|Flash|Chip RTL|
-|---|---|---|---|---|---|
-| hongyavision | LG-SG5T1 | No | PCB-SWTG024AS-V2.0_16895 | 25Q40 | 8272 |
-
-### Label specifications
-
- **Name**: 
- **Ports**:
-  - 5 × RJ45: 10/100/1000/2500 Mbps
-  - 1 × SFP+: 1000 / 2500 / 10000 Mbps
- **Power**: 12V DC, 1A  5525 connector 
-
-<img src="photos/SWTG024AS-V2.0/label.jpg" width="300" />
-
-### What works
-The device is fully supported:
- ALL 2.5GBASE-T RJ45 ports work at 10/100/1000/2500 Mbps
- The SFP+ port supports 1G, 2.5G and 10G modules 
- LEDs work with the same indiciations as the OEM firmware
- Online update does not work with 512KiB flash.
-### PCB overview
-
-**Board markings**
- Top silkscreen: PCB-SWTG024AS-V2.0
-
-Top side
-
-<img src="photos/SWTG024AS-V2.0/pcb_top.jpg" width="300" />
-
-Bottom
-
-<img src="photos/SWTG024AS-V2.0/pcb_bottom.jpg" width="300" />
-
-### J1, serial console
-
-| `J1` pin | Signal      |
-| -------- | ----------- |
-| 1        | GND         |
-| 2        | RX (Input)  |
-| 3        | TX (Output) |
-
-Note,`R52`、`R53`may not be installed.You need to bridge them using either solder or resistors.
-
-## Power supply
-
-Input power is delivered via barell plug, `12V 1A` adapter was provided.
@@ -9,8 +9,8 @@ Also the RJ45 connectors can be all plastic/non-shielded or with metal shielding
 |Brand|Type|Managed|PCB|PCB Label|Flash|Chip RTL|
 |---|---|---|---|---|---|---|
 | LIANGUO |SWTG024AS |No|  SWTG024AS-v2.0-17452 | CM-23-11-2336 023-17453| 512 KiB | 8272 |
-| Horaco |ZX-SWTG124AS | Yes |  SWTG024AS-v2.0 | ??? | ??? | 8272 |
-| Xikestore |SKS3200M-4GPY2XF | Yes |  SWTG024AS-v1.0 | CM-23-08-2043 023-16721 | 2048 KiB | 8272 |
+| Haraco |ZX-SWTG124AS | Yes |  SWTG024AS-v2.0 | ??? | ??? | 8272 |
+| Xikestore |SKS3200M-4GPY2XF | Yes |  SWTG024AS-v1.0 | CM-23-08-2043 023-16721 | ??? | 8272 |
 | Sodola | SL-SWTG124AS-D | Yes | SWTG024AS-v2.0-17452 | ??? | 2048 KiB | 8272 |

 ## PCB
@@ -1,183 +0,0 @@
-# ZX-SWTGW215AS
-
-## Brands
-
-|Brand|Type|Managed|PCB|Flash|Chip RTL|
-|---|---|---|---|---|---|
-| Lianguo | ZX-SWTGW215AS | Yes | PCB-SWTG115AS-V2.0 | FM25Q16A | 8372 |
-| sold as Lianguo, actual device unbranded | ZX-SWTGW215AS | Yes | PCB-SWTG115AS-V2.1 | W25Q16JVSIQ (2MiB) | 8372 |
-
-## RTLPlayground target
-
-Build for this device with `make MACHINE=LIANGUO_ZX_SWTGW215AS`, which selects the `machine/LIANGUO_ZX_SWTGW215AS.c` board definition.
-
-Physical hardware verification: 5x RJ45 ports + 1x SFP port. 
-Port 5 RJ45 is interfaced through a RTL8221B IC.
-
-## Label (V2.0)
-
-<img src="photos/ZX-SWTGW215AS-V2.0/label.jpg" width="300" />
-
-## PCB (V2.0)
-
-<img src="photos/ZX-SWTGW215AS-V2.0/pcb_top.jpg" width="300" />
-<img src="photos/ZX-SWTGW215AS-V2.0/pcb_bottom.jpg" width="300" />
-
-## PCB (V2.1)
-
-<img src="photos/ZX-SWTGW215AS-V2.1/pcb-top.jpg" width="300" />
-<img src="photos/ZX-SWTGW215AS-V2.1/pcb-bottom.jpg" width="300" />
-
-## Connectors
-
-### Port overview
-
-```
-┌──────────────────────────────────────────────────────────────────────────────────┐
-│                                                                   ┌──────────┐   │
-│     ┌─────────┐ ┌─────────┐ ┌─────────┐ ┌─────────┐ ┌─────────┐   │ SFP (J4) │   │
-│     │  RJ45   │ │  RJ45   │ │  RJ45   │ │  RJ45   │ │  RJ45   │   │  PORT 6  │   │
-│     │  PORT 1 │ │  PORT 2 │ │  PORT 3 │ │  PORT 4 │ │  PORT 5 │   │  LOG  8  │   │
-│  O  │  LOG  4 │ │  LOG  5 │ │  LOG  6 │ │  LOG  7 │ │  LOG  3 │   │ SerDes 1 │   │
-│ RST └─────────┘ └─────────┘ └─────────┘ └─────────┘ └─────────┘   └──────────┘   │
-└──────────────────────────────────────────────────────────────────────────────────┘
-```
-
-| Type | RTLPlayground logical ports | Physical index | 
-|---|---|---|
-| RJ45 | 3, 4, 5, 6, 7 | 1-5 | 
-| SFP | 8 | 6 |
-
-### J4
-
-* Location: SFP connector `J4`.
-* Connected to: 10GMAC number 8, SerDes 1.
-
-|`J4` SFP PINs | Signal | GPIO | Notes |
-|---|---|---|---|
-|3|	TX_DISABLE	      | GPIO_NA | Not connected |
-|4|	MODDEF2 – SDA     | GPIO39 | I2C SDA |
-|5|	MODDEF1 – SCL     | GPIO40	| I2C SCL |
-|6|	MODDEF0 – PRESENT | GPIO30 | Detect |
-|8|	LOS	              | GPIO37 | RX Loss of Signal |
-
-#### Notes
-* Not all signals were mapped mechanically, hence they've been left out of documentation.
-
-### T3, Slave Interface
-
-This connector goes to U4 `I2C EEPROM` and U10 `SPI FLASH` (mappings identical to SWTG024AS).
-
-For detailed Slave Interface functionality and protocol information, see [T3 documentation in SWTG024AS.md](SWTG024AS.md#t3-slave-interface).
-
-|`T3` pin|what|Signal|
-|---|---|---|
-|1| U4-P6, 33R U10-P6 | I2C-SCL, SPI-CLK, Slave SCK/SCL/MDC/EE_SCL |
-|2| GND | --- |
-|3| U4-P5, U10-P5 | I2C-SDA, SPI-DI/DO, Slave SDI/SDA/MDIO/EE_SDA |
-|4| VCC |
-|5| 33R -> U10-P2 | SPI-DO/D1 | 
-|6| U10-P1 | SPI-CS |
-
-#### Notes
-* 1 pin is square shaped.
-
-
-### T5, Serial Console
-
-|`T5` pin|GPIO|Signal|
-|---|---|---|
-| 1 | GPIO31 | U0TXD (Output) |
-| 2 | GND | |
-| 3 | GPIO32 | U0RXD (Input) |
-| 4 | 3V3 | |
-
-#### Notes
-* 1 pin is square shaped.
-
-### T8
-
-|`T8` pin|GPIO|Signal|
-|---|---|---|
-| 1 | GPIO46 | |
-| 2 | GND    | |
-| 3 | GPIO48 | |
-| 4 | 3V3    | |
-| 5 | GPIO47 | |
-| 6 | GPIO49 | |
-
-#### Notes
-* 1 pin is square shaped.
-* Mapping unverified but assumed the same as [LIANGUO SWTG024AS](SWTG024AS.md#t8).
-
-## Reset Circuit
-| Function | GPIO |
-|---|---|
-| Reset button | GPIO54 |
-
-### Notes
-* Circuit is active-low
-
-## GPIO
-
-Note: T3/U4/U10-related signal annotations below are copied from [LIANGUO SWTG024AS T3 section](SWTG024AS.md#t3-slave-interface) as well as T8 port from [LIANGUO SWTG024AS T8 section](SWTG024AS.md#t8). They should be treated as assumed identical for ZX-SWTGW215AS as it has not been 100% confirmed true at the moment. 
-
-| HEX VAL. | GPIO   | Component / Purpose | Notes |  | GPIO | Component / Purpose | Notes |
-| -------- | ------ |  ---- | ---- | ---- | ---- | ---- | ---- |
-| 00000001 | GPIO00 | | |  | GPIO32 | T5-3 | U0RXD |
-| 00000002 | GPIO01 | | |  | GPIO33 |   |  |
-| 00000004 | GPIO02 | | |  | GPIO34 |   |  |
-| 00000008 | GPIO03 | | |  | GPIO35 |   |  |
-| 00000010 | GPIO04 | | |  | GPIO36 |   |  |
-| 00000020 | GPIO05 | | |  | GPIO37 | J4-8 | SFP LOS |
-| 00000040 | GPIO06 | | |  | GPIO38 |   |  |
-| 00000080 | GPIO07 | | |  | GPIO39 | J4-4 | SFP I2C SDA |
-| 00000100 | GPIO08 | | |  | GPIO40 | J4-5 | SFP I2C SCL |
-| 00000200 | GPIO09 | | |  | GPIO41 |   |  |
-| 00000400 | GPIO10 | | |  | GPIO42 | U10-P6, U4-P6, T3-1 | SPI FLASH CLK / I2C-SCL (from [LIANGUO SWTG024AS](SWTG024AS.md#gpio)) |
-| 00000800 | GPIO11 | | |  | GPIO43 | U10-P5, U4-P5, T3-3 | SPI FLASH DI/IO0 / I2C-SDA (from [LIANGUO SWTG024AS](SWTG024AS.md#gpio)) |
-| 00001000 | GPIO12 | | |  | GPIO44 | U10-P2, T3-5 | SPI FLASH DO/IO1 (from [LIANGUO SWTG024AS](SWTG024AS.md#gpio)) |
-| 00002000 | GPIO13 | PORT1 LED GREEN |  |  | GPIO45 | U10-P1, T3-6 | SPI FLASH CS (from [LIANGUO SWTG024AS](SWTG024AS.md#gpio)) |
-| 00004000 | GPIO14 | PORT1 LED ORANGE |  |  | GPIO46 | T8-1 | (from [LIANGUO SWTG024AS](SWTG024AS.md#gpio)) |
-| 00008000 | GPIO15 | | |  | GPIO47 | T8-5 | (from [LIANGUO SWTG024AS](SWTG024AS.md#gpio)) |
-| 00010000 | GPIO16 | PORT2 LED GREEN |  |  | GPIO48 | T8-3 | (from [LIANGUO SWTG024AS](SWTG024AS.md#gpio)) |
-| 00020000 | GPIO17 | PORT2 LED ORANGE |  |  | GPIO49 | T8-6 | (from [LIANGUO SWTG024AS](SWTG024AS.md#gpio)) |
-| 00040000 | GPIO18 | PORT3 LED GREEN |  |  | GPIO50 |   |  |
-| 00080000 | GPIO19 | PORT3 LED ORANGE |  |  | GPIO51 |   |  |
-| 00100000 | GPIO20 | PORT4 LED GREEN |  |  | GPIO52 |   |  |
-| 00200000 | GPIO21 | PORT4 LED ORANGE |  |  | GPIO53 |   |  |
-| 00400000 | GPIO22 | PORT5 LED GREEN |  |  | GPIO54 | Reset Button | GPIO54_ACL_BIT2_EN |
-| 00800000 | GPIO23 | PORT5 LED ORANGE |  |  | GPIO55 |   |  |
-| 01000000 | GPIO24 | SFP LED GREEN | J4 |  | GPIO56 |   |  |
-| 02000000 | GPIO25 | | |  | GPIO57 |   |  |
-| 04000000 | GPIO26 | | |  | GPIO58 |   |  |
-| 08000000 | GPIO27 | | |  | GPIO59 |   |  |
-| 10000000 | GPIO28 | LED-SYSTEM |  |  | GPIO60 |   |  |
-| 20000000 | GPIO29 | | |  | GPIO61 |   |  |
-| 40000000 | GPIO30 | J4-6 | SFP DETECT |  | GPIO62 |   |  |
-| 80000000 | GPIO31 | T5-1 | U0TXD |  | GPIO63 |   |  |
-
-## LEDs
-
-| NAME | GPIO | Port(s) | Function | Notes |
-| ---- | ---- | ---- | ---- | ---- |
-| PORT1 LED GREEN | GPIO13 |5| Activity | LEDS_2G5, LEDS_LINK, LEDS_ACT |
-| PORT1 LED ORANGE | GPIO14 | 5 | Speed | LEDS_1G, LEDS_100M, LEDS_10M, LEDS_LINK, LEDS_ACT |
-| PORT2 LED GREEN | GPIO16 | 4 | Activity | LEDS_2G5, LEDS_LINK, LEDS_ACT |
-| PORT2 LED ORANGE | GPIO17 | 4 | Speed | LEDS_1G, LEDS_100M, LEDS_10M, LEDS_LINK, LEDS_ACT |
-| PORT3 LED GREEN | GPIO18 | 3 | Activity | LEDS_2G5, LEDS_LINK, LEDS_ACT |
-| PORT3 LED ORANGE | GPIO19 | 3 | Speed | LEDS_1G, LEDS_100M, LEDS_10M, LEDS_LINK, LEDS_ACT |
-| PORT4 LED GREEN | GPIO20 | 2 | Activity | LEDS_2G5, LEDS_LINK, LEDS_ACT |
-| PORT4 LED ORANGE | GPIO21 | 2 | Speed | LEDS_1G, LEDS_100M, LEDS_10M, LEDS_LINK, LEDS_ACT |
-| PORT5 LED GREEN | GPIO22 | 1 | Activity | LEDS_2G5, LEDS_LINK, LEDS_ACT |
-| PORT5 LED ORANGE | GPIO23 | 1 | Speed | LEDS_1G, LEDS_100M, LEDS_10M, LEDS_LINK, LEDS_ACT |
-| SFP LED GREEN | GPIO24 | 6 (SFP J4) | Multi-speed | LEDS_10G, LEDS_5G, LEDS_2G5, LEDS_1G, LEDS_100M, LEDS_LINK, LEDS_ACT |
-| LED-SYSTEM | GPIO28 | --- | System status | --- |
-
-## Notes
-
-While [SWTG024AS.md](SWTG024AS.md) can be used as a general reference for hardware concepts and interface specifications, this device should not be assumed to be identical beside the difference implicitely highlighted below. Not all information has been validated for compatibility with the SWTG215AS. Consult the SWTG024AS documentation with caution and verify any critical details against this device's.
-
-## Flashing
-
-For devices with Winbond 25Q16JVSIQ, flashing is possible for example using flashprog with device "W25Q16.V". Note that you should not overwrite the whole flash to keep device-specific data (like the MAC address at 0x1fc000). Also, creating a backup of the entire falsh before is of course a very good idea.
@@ -1,25 +0,0 @@
-### ZX-SWTGW218AS
-
-## Brands
-|Brand|Type|Managed|PCB|Flash|Chip RTL|
-|---|---|---|---|---|---|
-| Mokerlink | ZX-SWTGW218AS | Yes|  SWTG118AS-V2.0-16029 | 2MB (FM25Q16A)| 8273N + 8224N |
-| Sodola | | | | | |
-| Horaco | | | | | |
-| XikeStor | SKS3200-8E1X | Yes | SWTG118AS-V2.1-17462 | 2MB (25Q16JVSIQ) | |
-
-
-## Photos
-
-<img src="photos/SWTGW218AS-managed/front.png" width="800" />
-
-<img src="photos/SWTGW218AS-managed/label.jpg" width="800" />
-
-## PCB
-
-See up'n'atom's Repo:
-
-https://github.com/up-n-atom/SWTG118AS/blob/main/photos/SWTG118AS-v2.0/SWTG118AS-v2.0-pcb-top.JPG
-
-https://github.com/up-n-atom/SWTG118AS/blob/main/photos/SWTG118AS-v2.0/SWTG118AS-v2.0-pcb-bottom.JPG
-
@@ -1,174 +0,0 @@
-# TrendNet TEG-S562
-
-Following is documentation for unmanaged switch marked as `TEG-S563/EU H/W: V1.0R`.
-
-Original software is running UART on 57600 baud rate. The software does not allow to
-do anything fancy via serial. There is `IP` configuration which can be printed as well.
-There might be also some flash upload procedure, but using SPI clamp in-board seems to
-be easier method.
-
-The memory chip is `Winbond W25Q16JV` with 16M-bit size.
-
-## What does work
-
-1. 2.5G ports on all advertised speeds.
-2. SFP+ communication.
-3. Serial, Web UI.
-4. All LEDs
-
-## Known issues
-
-None.
-
-## PCB
-
-Manufacturer information be found [on the product page](https://www.trendnet.com/support/support-detail.asp?prod=105_TEG-S562).
-
-Top side
-
-<img src="photos/TEG-S562/TEG-S562-v1.0R-top.jpg" width="300" />
-
-Bottom
-
-<img src="photos/TEG-S562/TEG-S562-v1.0R-bottom.jpg" width="300" />
-
-## Connectors
-
-### Port overview
-
-```
-┌─────────────────────────────────────────────────────────────────────────────┐
-│                                                   ┌──────────┐ ┌──────────┐ │
-│ ┌─────────┐ ┌─────────┐ ┌─────────┐ ┌─────────┐   │ SFP    2 │ │ SFP    1 │ │
-│ │  RJ45   │ │  RJ45   │ │  RJ45   │ │  RJ45   │   │ PORT   5 │ │ PORT   6 │ │
-│ │  PORT 1 │ │  PORT 2 │ │  PORT 3 │ │  PORT 4 │   │ MAC    8 │ │ MAC    3 │ │
-│ │  MAC  4 │ │  MAC  5 │ │  MAC  6 │ │  MAC  7 │   │ SerDes 0 │ │ SerDes 1 │ │
-│ └─────────┘ └─────────┘ └─────────┘ └─────────┘   └──────────┘ └──────────┘ │
-└─────────────────────────────────────────────────────────────────────────────┘
-```
-
-### J2, serial console
-
-| `J2` pin | Signal      |
-| -------- | ----------- |
-| 1        | 3V3         |
-| 2        | TX (Output) |
-| 3        | RX (Input)  |
-| 4        | GND         |
-
-Note: 1 pin is square shaped, towards the power input.
-
-### J5, power pass-thru
-
-| `J5` pin | Signal |
-| -------- | ------ |
-| 1        | 12V    |
-| 2        | 12V    |
-| 3        | GND    |
-| 4        | GND    |
-
-Note: 1 pin is square shaped.
-
-### U5, I2C eeprom placeholder
-
-| `J5` pin | Signal        |
-| -------- | ------------- |
-| 1        | GND           |
-| 2        | GND           |
-| 3        | GND           |
-| 4        | GND           |
-| 5        | 3V3           |
-| 6        | ??? Logic Low |
-| 7        | SCL           |
-| 8        | SDA           |
-
-SOC I2C address is 0x5c.
-
-### SW1 GPIO switch?
-
-Not populated but looks like a switch for selecting
-GPIO level. Missing resistors in place.
-
-GPIO mapping unknown.
-
-### S2 Reset ciruit
-
-Not populated but looks like a button can be added on `S2` connector,
-requires additional `R571` resistor which will pull signal to ground.
-
-GPIO mapping unknown.
-
-### GPIO
-
-| HEX VAL. | GPIO   | When            | GPIO   | When                   |
-| -------- | ------ | ----------------| ------ | -----------------------|
-| 00000001 | GPIO00 |                 | GPIO32 |                        |
-| 00000002 | GPIO01 |                 | GPIO33 |                        |
-| 00000004 | GPIO02 |                 | GPIO34 | Random changes         |
-| 00000008 | GPIO03 |                 | GPIO35 |                        |
-| 00000010 | GPIO04 |                 | GPIO36 | SFP2 Present           |
-| 00000020 | GPIO05 |                 | GPIO37 | SFP2 RX Los            |
-| 00000040 | GPIO06 |                 | GPIO38 | SFP1 Present           |
-| 00000080 | GPIO07 |                 | GPIO39 |                        |
-| 00000100 | GPIO08 |                 | GPIO40 |                        |
-| 00000200 | GPIO09 |                 | GPIO41 |                        |
-| 00000400 | GPIO10 |                 | GPIO42 | Random changes         |
-| 00000800 | GPIO11 |                 | GPIO43 |                        |
-| 00001000 | GPIO12 | PORT1 Link      | GPIO44 |                        |
-| 00002000 | GPIO13 | PORT1-LED-GREEN | GPIO45 |                        |
-| 00004000 | GPIO14 | PORT1-LED-AMBER | GPIO46 | SFP1 I2C CLK           |
-| 00008000 | GPIO15 | PORT2 Link      | GPIO47 | SFP1 I2C SDA           |
-| 00010000 | GPIO16 | PORT2-LED-GREEN | GPIO48 | SFP2 I2C CLK           |
-| 00020000 | GPIO17 | PORT2-LED-AMBER | GPIO49 | SFP2 I2C SDA           |
-| 00040000 | GPIO18 | PORT3 Link      | GPIO50 | SFP1 Rx LOS            |
-| 00080000 | GPIO19 | PORT3-LED-GREEN | GPIO51 | SFP2 TX Disable        |
-| 00100000 | GPIO20 | PORT4-LED-AMBER | GPIO52 |                        |
-| 00200000 | GPIO21 | PORT4 Link      | GPIO53 |                        |
-| 00400000 | GPIO22 | PORT4-LED-GREEN | GPIO54 | SFP1 TX Disable        |
-| 00800000 | GPIO23 | PORT4-LED-AMBER | GPIO55 |                        |
-| 01000000 | GPIO24 |                 | GPIO56 |                        |
-| 02000000 | GPIO25 |                 | GPIO57 |                        |
-| 04000000 | GPIO26 |                 | GPIO58 |                        |
-| 08000000 | GPIO27 |                 | GPIO59 |                        |
-| 10000000 | GPIO28 |                 | GPIO60 |                        |
-| 20000000 | GPIO29 |                 | GPIO61 |                        |
-| 40000000 | GPIO30 |                 | GPIO62 |                        |
-| 80000000 | GPIO31 |                 | GPIO63 |                        |
-
-## LEDs
-
-Ports 1-4 are amber for 100M/1G links, Green for 2.5G.
-Port 5-6 are green for 10G/1G link. Both should flash on activity.
-
-| NAME             | When active    |
-| ---------------- | ---------------|
-| PWR              | 3V3            |
-| SFP1             |                |
-| SFP2             |                |
-| PORT1-LED-GREEN  | -              |
-| PORT2-LED-GREEN  | PORT2 2.5G     |
-| PORT3-LED-GREEN  | PORT3 2.5G     |
-| PORT4-LED-GREEN  | PORT4 2.5G     |
-| PORT1-LED-AMBER  | PORT1 1GB/100M |
-| PORT2-LED-AMBER  | PORT2 1GB/100M |
-| PORT3-LED-AMBER  | PORT3 1GB/100M |
-| PORT4-LED-AMBER  | PORT4 1GB/100M |
-
-## Power supply
-
-Input power is delivered via barell plug, `12V 1A` adapter was provided.
-Board has two supply rails. `0.95` and `3.3` volt.
-
-### `0.95` Core Voltage
-
-Voltage is made by a `APW8713` (U3).
-
-### `3.3` Voltage
-
-Voltage is crated regulated by chip marked as `GoIAT` (U2).
-
-## SFP SPI
-
-There is separate clock and data lines for both SFP modules. MSDA/MSCK 0 and 1 need to be enabled.
-
-SFP1 slot is connected to SPI0. SFP2 slot is connected to SPI1.
@@ -1,59 +0,0 @@
-# ZX310S-4T2XH/
-
-The following is a documentation for the managed switch marked as `ZX310S-4T2XH`
-and sold by Horaco.
-
-The original software is running UART on 57600 baud rate. The solder holes
-of the UART header are filled in. In order to install a UART header, they
-need to be cleared first. A 1.2mm drill can be used, alternatively a
-de-soldering wick.
-The original firmware uses 57600 baud 8N1
-
-CPU: RTL8372
-Flash: 2MByte Winbond W25Q16DV (U3)
-PHY RTL8261BE
-
-### Label specifications
-
- **Name**: 
- **Ports**:
-  - 4 × RJ45: 10/100/1000/2500 Mbps
-  - 1 x RJ45: 10/100/1000/2500/5000/10000 Mbps
-  - 1 × SFP+: 1000 / 2500 / 10000 Mbps
- **Power**: 12V DC, 2A barrel connector 
-
-<img src="photos/ZX310S-4T2XH/label.jpg" width="300" />
-
-### What works
-The device is fully supported:
- All 4 2.5GBASE-T RJ45 ports work at 10/100/1000/2500 Mbps
- The 10GBit port works. TODO: Fix EEE, speed selection
- The SFP+ port supports 1G, 2.5G and 10G modules 
- LEDs work with the same indiciations as the OEM firmware
-
-### PCB overview
-
-**Board markings**
- Top silkscreen: PCB-SL310S-4T1T1X-V1.0.1-24107
-
-Top side
-
-<img src="photos/ZX310S-4T2XH/pcb_top.jpg" width="300" />
-
-Bottom
-
-<img src="photos/ZX310S-4T2XH/pcb_bottom.jpg" width="300" />
-
-### J1, serial console
-
-| `J1` pin | Signal      |
-| -------- | ----------- |
-| 1        | TX (Output) |
-| 2        | RX (Input)  |
-| 3        | GND         |
-| 4        | 3V3         |
-
-
-## Power supply
-
-Input power is delivered via barell plug, `12V 2A` adapter was provided.
@@ -1,53 +0,0 @@
-# ZX310S-4T2XT
-
-The following is a documentation for the managed switch marked as
-`ZX310S-4T2XT` and sold by Horaco.
-
-The original software is running UART on 57600 baud rate 8N1.
-
-CPU: RTL8372
-Flash: 2MByte Winbond W25Q16DV (U3)
-PHY 2x RTL8261BE
-
-### Label specifications
-
- **Name**:
- **Ports**:
-  - 4 × RJ45: 10/100/1000/2500 Mbps
-  - 2 x RJ45: 10/100/1000/2500/5000/10000 Mbps
- **Power**: 12V DC, 2A barrel connector
-
-<img src="photos/ZX310S-4T2XT/label.jpg" width="300" />
-
-### What works
-The device is fully supported:
- All 4 2.5GBASE-T RJ45 ports work at 10/100/1000/2500 Mbps, including EEE
- The 10GBit ports works, including EEE.
- LEDs work with the same indiciations as the OEM firmware
-
-### PCB overview
-
-**Board markings**
- Top silkscreen: PCB-SL310S-4T2XT-V1.0.0-22273
-
-Top side
-
-<img src="photos/ZX310S-4T2XT/pcb_top.jpg" width="300" />
-
-Bottom
-
-<img src="photos/ZX310S-4T2XT/pcb_bottom.jpg" width="300" />
-
-### J1, serial console
-
-| `J1` pin | Signal      |
-| -------- | ----------- |
-| 1        | TX (Output) |
-| 2        | RX (Input)  |
-| 3        | GND         |
-| 4        | 3V3         |
-
-
-## Power supply
-
-Input power is delivered via barell plug, `12V 2A` adapter was provided.
Author	SHA1	Message	Date
logicog	347950ff72	Add support for the ZX_SWTGW215AS device built by Hasivo The device is sold under the name ZX_SWTGW215AS without necessarily a Hasivo branding, however the firmware and the PCB are marked with Hasivo. The PCB is marked Hasivo RTL_SGT-1SX V1.5 SoC: RTL8372 Ethernet: 5 x 2.5GBit (RTL8221B + 4*SoC) SFP+: 1x 10GBit (SoC) The device has a slider switch and a reset button. Reset: GPIO 54 (active-low) Slider: GPIO 51 (right is high)	2026-02-06 07:19:12 +01:00
logicog	0bccfbd11f	Add LED-pad mapping	2026-02-05 19:41:28 +01:00
logicog	360bc1e86d	Use generic led configuration	2026-02-03 19:24:36 +01:00
logicog	5b385385de	Add LED configuration in machine profile	2026-02-01 22:15:12 +01:00
logicog	ea23dfedc5	Add generic LED configuration support	2026-02-01 22:15:12 +01:00
logicog	34a32fa7e8	Reduce DSEG usage as we need 1 OSEG byte	2026-02-01 22:15:12 +01:00
logicog	06930df7c6	Remove debug output	2026-02-01 22:15:12 +01:00
logicog	df058dfe33	LED configuration support	2026-02-01 22:15:12 +01:00
logicog	45213b4eac	Add MACHINE_HG0402XG_V1_1	2026-02-01 22:15:12 +01:00