When adding a new VLAN, we should load it after addition
Prevent deleting the mgmt vlan
Adding a button to promote a vlan to be the management VLAN
We can't create a vlan called d or mgmt as that clashes with the
commands to delete and promote a vlan
Making the Management VLAN more obvious and adding a "confused"
disabled button to where delete and promote are
Switching to the i image and making it so you can click the entire
row apart from the cell where the buttons are (to prevent accidents)
Cleaning up the last bits of ingress filtering I can see
Also making the first VLAN in the table load when we load the UI
Removing the tickbox for the PVID, I'll swap this out to ticks
or something later on, but the PVID will be automatically set
based on the untagged membership, otherwise it will be 1
Send the vlan with name command when attempting to add a new VLAN
Because of the structure of the vlan command, we need to send the name as well if its set
Set the PVID based on the untagged membership and reload the
table when applied. We need to block setting the PVID to the tagged by proxy
Blue button
Need to provide array of pvid commands not concat
Storing state of each vlan so we can refer later
Blue button
The 8051 assembler sign-extends every value to 24 bits, so the top
byte of a __sfr32 address list like 0xa4a5a6a7 comes out as 0xff.
The patch keeps 32-bit arithmetic while leaving the 24-bit T line
addresses alone, so the relocations are unchanged. Proposed upstream
in the bug thread. With it SFR_DATA_U32 can be used again, which
saves about 240 bytes of code in REG_SET.
The workflow and the Dockerfile install what building SDCC needs instead
of the distribution's sdcc, and the workflow caches toolchain/ keyed on
the contents of sdcc/.
Released SDCC 4.5.0 and 4.6.0 miscompile some of our code in the mcs51
register allocator (SDCC bugs 4153 and 4154, fixed in trunk r17025 and
r17039). The first make now downloads the 4.6.0 sources, checks their
sha256, applies the two fixes from sdcc/ and installs the compiler into
toolchain/, named after a checksum of sdcc/, so a changed patch builds a
new one. make CC=sdcc still uses an installed compiler.
The masks were 0, so 0x3e2 was ORed into the reset value 0xbff and both
SerDes stayed off on boards without 10G ports (n_10g == 0), e.g. the
HC-SWTG124AS. With SDS 0 off RTL837X_REG_SEC_COUNTER does not hold a
written value: it reads 0, so NTP never retried after a failed first
attempt at boot and froze the clock after a sync.
Tested with regset on an HC-SWTG124AS: the register keeps a write with
SDS 0 in SGMII or 10GR, not with SDS 0 off (also not with only SDS 1
on).
Firefox filled a saved login into the System tab's password fields and
its user name into the NTP poll interval, the input before them. That
input event marked the Time card as edited, so ntpLoad() left NTP off,
the server empty and the time zone at UTC-12:00.
In HEALTH=1 builds health_phase(HEALTH_LLDP) used id 7 while ph_max[] and
ph_slow[] had HEALTH_PHASES = 6 entries. The LLDP checkpoint therefore
wrote one byte past ph_max (into the high byte of ph_slow[0]) and, when
the phase took two ticks or more, incremented two bytes past ph_slow
(dhcp_state.state and transaction_id on KP_9000_6XHML_X2).
Rename it HEALTH_PH_LLDP = 6, derive HEALTH_PHASES from it so the arrays
always cover the last phase, print an lldp line in "health" and document
it.
Fixes#658
Chrome on macOS labels .bin files application/macbinary. Searching for application/octet-stream mistakes the image bytes for more part headers and aborts when the preamble buffer fills.
Find the multipart header terminator instead, after the HTTP separator retained by handle_post. Keep authentication, CRC checks and staging limits unchanged. Cover MacBinary, an omitted part Content-Type, and a split header terminator with exact staged-byte checks.
Rob Emery
logicog
d00f
feelfree69
avicarmeli
robs
Luca S.
HL Yi
René van Dorst
Andre Brait