Hardware reset starts the firmware with SFR 0x97 = 1, which maps xdata
0x4000-0xbfff to the flash image: reads return flash bytes, writes are
lost. main() cleared it only after __mcs51_genXINIT and the XSEG clear
had run, so XISEG (initialised globals) and the part of XSEG above
0x4000 kept stale RAM contents, e.g. session_timeout = 4484 and LLDP
blocked on logical ports 0, 3 and 5. Clear it in
__sdcc_external_startup(), which SDCC calls before both.
Rename SFR_97 to MAP_FLASH_PAGE_TO_XDATA.
SW1 on PCB-SWTG024AS-A-V2.0.1_19650 is wired to GPIO48. Measured on
HC-SWTG124AS: GPIO48 reads 1 idle and 0 while the button is held.
HC_SWTG124AS.c is a symlink to PCB_SWTG024AS_A_2_0_1.c.
A commit hash can be looked up directly, a checksum cannot. Print the last commit that touched sdcc/, with -dirty for local changes, and fall back to the checksum when git is not available. The toolchain directory keeps the checksum.
The boot banner and the version command print the SDCC release and
revision from the compiler's own macros, and the name of the in-tree
toolchain the Makefile built, which is the checksum of sdcc/ and so
changes with every patch in it. A build with CC given on the command
line says "system" instead, since that compiler need not carry the
patches. A plain release and the same release with the patches report
the same revision, so the toolchain line is what tells them apart.
Costs 66 bytes of BANK2.
Review feedback on #560 (DrDoof):
- A login that came with a cookie that is still valid took a second
slot. The first one looked fresh, so the next login could push out
someone who is using the switch. The slot of the cookie now gets the
new id.
- Changing the password leaves no old login valid: session_init() from
parse_passwd(). With one session the next login pushed a leftover one
out, with several it would stay valid until the next restart.
- The 32-bit comparison of the last use times moves into a leaf function,
so the compiler does not give it a 4-byte scratch in internal RAM.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
The web server's bank had no room left for the four sessions once the
original firmware's more robust header handling came in. Picking a slot,
checking a cookie and starting a session move to sessions.c in bank 3;
httpd.c only calls session_init(), session_check() and session_new().
The random id is written straight into the reply, which drops
gen_random_hex_chars() from bank 1.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Logging in from a second browser ended the first one's session at its next
request: two browsers open on the switch logged each other out every few
seconds. Up to four sessions now, each with its own cookie and expiry; a
fifth login replaces the least recently used. The expiry check is a leaf
function so its 32-bit scratch stays out of internal RAM (stack still
159 bytes with HEALTH).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01Tx2W7xVecMoKbBCkD2i8PG
(cherry picked from commit 03330f4077ef8872d861d951c8e44ece3c573935)
it'll accept just the definition.
Also throughout the regex we have over-specified the number of digits
sometimes ports are 4 digits long, sometimes they are 2. This seems
unnecessary, 1 or more is sufficient
the user clicks apply on the specific vlan. In order for this to
work when the user is simultaneously changing the vlan that their
machine is connected through and the mgmt vlan id, we need to be
able to send a batch of commands through to the switch atomically
so the switch can process all of them and the momentary disconnection
of the machine doesn't matter
When adding a new VLAN, we should load it after addition
Prevent deleting the mgmt vlan
Adding a button to promote a vlan to be the management VLAN
We can't create a vlan called d or mgmt as that clashes with the
commands to delete and promote a vlan
Making the Management VLAN more obvious and adding a "confused"
disabled button to where delete and promote are
Switching to the i image and making it so you can click the entire
row apart from the cell where the buttons are (to prevent accidents)
Cleaning up the last bits of ingress filtering I can see
Also making the first VLAN in the table load when we load the UI
Removing the tickbox for the PVID, I'll swap this out to ticks
or something later on, but the PVID will be automatically set
based on the untagged membership, otherwise it will be 1
Send the vlan with name command when attempting to add a new VLAN
Because of the structure of the vlan command, we need to send the name as well if its set
Set the PVID based on the untagged membership and reload the
table when applied. We need to block setting the PVID to the tagged by proxy
Blue button
Need to provide array of pvid commands not concat
Storing state of each vlan so we can refer later
Blue button
html_min was phony, so every make deleted output/html_min and minified
all of html/ again, even with nothing changed. A stamp file now stands for
the minified copy and depends on the sources and on minify.py. A list of
the source names, rewritten only when it changes, is a dependency too, so
adding or removing a file in html/ still redoes the copy and a removed
file does not stay behind in the image. If output/html_min is missing,
the stamp is remade in the same run.
The note on version.h in webui-compression.md still said it was phony.
Three more bench scenarios around the closing boundary. Every value
of the last image byte, uploaded whole and split right after the
payload, must end the part. A run of CR before the boundary of even
length passed before the fix and an odd one did not, so both are
checked. An image made of CR only, longer than a flash page, and one
made of repeated "\r\n-" exercise the broken matches back to back:
each one appends to the page buffer without a byte written, and the
page flush after both paths has to keep up.
stream_upload() matches the closing multipart boundary byte by byte.
When a byte breaks a partial match, the matched prefix goes to flash as
data, and so does the breaking byte, without being compared against the
start of the boundary.
The boundary starts with "\r\n--", so an image whose last byte is '\r'
never completes: that '\r' starts a match, the '\r' of the boundary
breaks it and is written as data, and the rest of the boundary no
longer matches. The browser waits for a reply that never comes.
Flush the matched prefix and look at the breaking byte again from the
start of the boundary. A boundary may not contain CR, so no longer
suffix of the matched prefix can start a new match.
The 8051 assembler sign-extends every value to 24 bits, so the top
byte of a __sfr32 address list like 0xa4a5a6a7 comes out as 0xff.
The patch keeps 32-bit arithmetic while leaving the 24-bit T line
addresses alone, so the relocations are unchanged. Proposed upstream
in the bug thread. With it SFR_DATA_U32 can be used again, which
saves about 240 bytes of code in REG_SET.
The workflow and the Dockerfile install what building SDCC needs instead
of the distribution's sdcc, and the workflow caches toolchain/ keyed on
the contents of sdcc/.
Released SDCC 4.5.0 and 4.6.0 miscompile some of our code in the mcs51
register allocator (SDCC bugs 4153 and 4154, fixed in trunk r17025 and
r17039). The first make now downloads the 4.6.0 sources, checks their
sha256, applies the two fixes from sdcc/ and installs the compiler into
toolchain/, named after a checksum of sdcc/, so a changed patch builds a
new one. make CC=sdcc still uses an installed compiler.
Andre Brait
logicog
feelfree69
rwalli@gmx.at
dobodu
d00f
Rob Emery
HL Yi
Brunoz78andClaude Sonnet 5.5
avicarmeli