The TODO next to the disabled TCP checksum code asks which bit of the RX tag
carries the result. It is bit 2 of byte 1: the hardware sets it when the L4
checksum is bad.
That answers the question for UDP as well, which was not being checked either
because UIP_CONF_UDP_CHECKSUMS is 0. Both paths now read the flag instead of
running a checksum over the payload on the 8051.
A zero UDP checksum, which is optional in IPv4, is not flagged by the hardware,
so DHCP keeps working and no extra condition is needed.
rx_headers lives in rtlplayground.c, which the host tests do not link, so
test_httpd_tx carries the storage itself the way it already carries uip_buf.
A zeroed descriptor reads as a good checksum, so the existing scenarios are
unaffected.
A new scenario sets the flag on a request and expects it counted as a checksum
error and left unanswered, then sends the same request with the flag clear and
expects it served. Built against uip.c without this change, those first two
checks fail and the two control checks still pass, so the scenario tells the
two versions apart rather than merely exercising the code.
Costs 156 bytes of code on SWTGW218AS and no extra XDATA.
The speed selector on the Ports tab was filled with its options and never
given a value, so it read "auto" on every load whatever the port was set
to. Forcing a port to 1G and reloading showed "auto" in the selector
beside a link badge reading 1G.
The advertisement bits ports.json already reports say what the port is
set to: phy_set_speed() writes the same three registers the JSON reads
back, and every forced speed leaves exactly one of the six bits standing
while auto leaves the lot. Map those to the selector, and leave it alone
while it has focus, as the MTU field does.
Values with no entry in the table, such as the 100M setting that
advertises both duplex modes, leave the selector untouched rather than
claim a setting the list cannot express.
leds_setup() walks all four LED sets and writes the high-speed nibble of
each into one of two registers, LED3_0_SET1 for sets 0 and 1 and
LED3_0_SET3 for sets 2 and 3. The second branch reuses the index
expression of the first without rebasing it, so sets 2 and 3 address
sfr_data[-1], [-2], [-3] and [-4].
Two things follow. Sets 2 and 3 never receive their nibble, because the
read-modify-write pair writes back exactly what it read. And four bytes
below sfr_data are overwritten on every boot of every machine: the loop
runs over all four sets whatever the board declares. On this build the
linker places sfr_data directly after the serial receive ring, so the
writes land in the tail of that ring.
leds_dump() reads the same two registers back and already rebases with
(set - 2); use the same form here.
The helper landed between that comment and the function it describes, so the
comment now reads as if it belonged to name_char(). Moving the helper up puts
the two back together. The generated code is unchanged.
gcc flags the else whose only statement is dbg_string(), because that macro
expands to nothing unless DEBUG is on, leaving the branch with an empty body.
The line is older than this branch; the bench is simply the first thing that
compiles httpd.c with a host compiler and -Wall -Wextra.
Turn warnings into errors in the test Makefile too, so the next one is caught
where it appears instead of scrolling past. It is the only warning the four
test binaries produce, so nothing else has to change.
Drives the unmodified httpd.c and uip.c through a handshake and a GET
from a client that moves its receive window, and compares the bytes that
reach the wire with the file they are meant to carry. The served file
holds a position-dependent pattern, so a repeat or a gap is reported at
its offset rather than as content that differs somewhere.
The first scenario holds the window still and must pass: it is the check
that the bench itself is sound, before the two moving-window scenarios
are believed.
uip_mss() is the limit on the next segment, not a record of the last
one: uIP recomputes it from the window the peer advertises in every
incoming segment, before the application is called. The ACK path
subtracted it from slen and added it to o_idx, and the retransmit path
handed it to uip_send(), so whenever the window moved between a segment
going out and its ACK coming back, the file being served lost or
repeated the difference. A window shrinking from 1460 to 600 between the
two repeats 860 bytes under fresh sequence numbers, which a browser
writes into the file; a window opening the same way skips 860.
Remember the length in tx_send() and use it in both places. The
retransmit path then repeats exactly the segment uIP still counts as
outstanding, which is what uip_connr->len makes it put on the wire.
uip_appdata is void *, so p - uip_appdata subtracts pointers of
different types. SDCC accepts it, C does not, and no host compiler will
build the file for a unit test. Cast to the type the byte count is meant
in; the generated firmware code is unchanged.
The vendor, model and serial strings are filtered while the EEPROM read
fills the buffers, so the page copies them out as they are. NUL still
ends a string, so a field shorter than its slot reads the same as before.
The three loops in send_status() become one call each. strcpy() cannot
return the length: rtl837x_common.h hides that prototype under
RTLP_HOST_TEST so host builds take the C library version, and a call
that adds its result to slen does not compile there. A small static
helper does the copy instead, and bank 1 drops by 96 bytes.
The console, POST /cmd and the saved config all go through the command
parser, so one filter there covers every way a name can be set. The
hostname already did this inline; port and VLAN names now do it too.
The SFP strings still need escaping on the way out: they come from the
module's EEPROM, not from a command.
A port named NAS"1 made status.json unparsable, so the page stopped
loading, and the name survives a reboot in the saved config. VLAN names
and the SFP strings have the same problem.
They now go through a helper that replaces ", \ and non-printable bytes
with a dot, the way the hostname is already sanitized on ingest. The
length does not change, so the size checks still hold.
The helper also covers the 0xa0 byte that send_sfp_info() skipped as a
special case, so that check is gone.
Compiling these two files for the host turns up warnings that SDCC does
not print: four places mix & with | and two mix && with ||, and l2_delete
keeps a counter it never reads. The parentheses only say what the
compiler already does, so the generated code is unchanged.
counter_to_html() reads the SFRs directly for the zero test, which saves
14 bytes of bank 1.
page_impl.c and rtl837x_port.c are linked together over the simulated
engine, so /vlan.json, /vlanlist and /l2.json are checked against what
vlan_create, pvid and the L2 table hold, through the same bytes the switch
would. The L2 walk is driven the way the web page drives it, page after
page until an index repeats, which is also where the repeat of the first
entry is pinned down as the wrap marker the page relies on. The counter
test fails on the code before the previous commit.
send_status wrote the high and the low word of a packet counter one after
the other, each without its leading zeros. That reads fine until a port
passes four billion packets; from then on a low word of 5 prints as "0x15"
next to a high word of 1, and the rates the page derives from the
difference between two readings jump around. send_counters already padded
the low word, so both now share one helper that pads it only when the high
word is set, which also drops the leading "0" the counters page used to
print in front of every small value.
The switch is reached through four register functions and the SFR_DATA
registers, so a flat register file behind them is enough to run the table
code on the host. A few addresses are live: writing TBL_CTRL with EXECUTE
performs the VLAN or L2 operation at once and clears the bit, STAT_GET
fetches a counter, L2_TBL_FLUSH_CTRL drops entries. Nothing ever reports
busy, so a polling loop runs once and the tests say nothing about what
happens when hardware stalls; that question was settled elsewhere.
The header states the VLAN and L2 entry layouts on its own, so a test can
hold what rtl837x_port.c writes against a second reading of the same bits
rather than against itself. The first suite does that for the VLAN entry,
the PVID register two ports share, the static multicast and management
entries, the per-port flush and the trunk registers. Two stub headers stand
in for the ones a firmware build generates, so the harness needs no SDCC
build first.
Two things kept every register-driven module out of the host harness. The
SFR keywords were unknown, so rtl837x_sfr.h did not compile at all, and once
it did, each translation unit would have defined its own copy of the
registers. They map to extern declarations now; a mock emits the storage
once by re-including the header with the keywords redefined.
The other was memset. rtl837x_common.h hides the firmware's own prototypes
under RTLP_HOST_TEST so host builds use the C library, but nothing declared
the library versions, and the modules do call them. The shim pulls in
string.h ahead of everything, where nothing can clash with it.
The messages said Error: themselves, or usage:, or nothing at all.
cmd_error() prints the prefix now, so every rejected command answers the
same way and the strings only carry what is specific to them.
Two messages that started with Error or refusing are reworded so the
prefix does not read twice. The syslog usage text becomes one string
instead of three calls.
run_cmd_body() answers POST /cmd with 400 when err_status is set, but
only the tokenizer set it. Every "Error:", "Invalid ..." and "Unknown
command" from the parsers went back as 200, so the web page reported the
command as applied, and save_cmd put the rejected line into the command
history, from where Save to flash wrote it into the startup config.
Set ERR_INVALID_ARGUMENT on every path that rejects a command: the err:
labels of the parsers, the parsers that print their own error, the
stp parser and the unknown command fallback. Warnings that still apply
the command, such as a full VLAN name table, are left alone.
Record a command in the history only when it was accepted, and let
execute_commands() report the first failure of a multi-line body, since
cmd_tokenize() clears err_status again for every following line.
The workflow only ran on push, so a pull request opened from a fork
never got a build, and neither did the host-side unit tests that run in
the same job.
René van Dorst
d00f
SkullyDev
SkullyDev
bloqaudio
Sylwester Petela
Rob Emery
Rob Emery
bennydiamond