Merge pull request #141 from logicog/SWTG018AS_A_V_2_0

Add support for the SWTG018AS-A V2.0 8+1 unmanged switch

doc/devices/SWTG018AS_A_V2_0.md

@@ -0,0 +1,54 @@
+# SWTG018AS-A V2.0
+
+The following is a documentation for the unmanaged switch marked as `SWTG018AS-A V2.0`.
+It is e.g. sold under the Ampcom brand, but no branh-markings are found on the device.
+
+The original software is running UART on 9600 baud rate. 
+
+Using a SOIC clamp in-board is the only method for initial installation.
+
+The board has a single flash chips `BS` with 4M-bit size. The front switch, switches between the two flash chips.
+These can be programed independently by using said switch - so it is e.g. possible to run the original and new firmware in parallel.
+
+### Label specifications
+
+- **Name**: 9-Ports 2.5G Ethernet Switch
+- **Ports**:
+  - 8 × RJ45: 10/100/1000/2500 Mbps
+  - 1 × SFP+: 1000 / 2500 / 10000 Mbps
+- **Power**: 12V DC, 1A barrel connector 
+
+<img src="photos/SWTG018AS_A_V_2_0/label.jpg" width="300" />
+
+### What works
+The device is fully supported:
+- All 8 2.5GBASE-T RJ45 ports work at 10/100/1000/2500 Mbps
+- The SFP+ port supports 1G, 2.5G and 10G modules 
+- LEDs work with the same indiciations as the OEM firmware
+
+### PCB overview
+
+**Board markings**
+- Top silkscreen: SWTG018AS-A-V2.0.1_19649
+
+Top side
+
+<img src="photos/SWTG018AS_A_V_2_0/pcb_top.jpg" width="300" />
+
+Bottom
+
+<img src="photos/SWTG018AS_A_V_2_0/pcb_bottom.jpg" width="300" />
+
+### J1, serial console
+
+| `J1` pin | Signal      |
+| -------- | ----------- |
+| 1        | 3V3         |
+| 2        | GND         |
+| 3        | RX (Input) |
+| 4        | TX (Output)  |
+
+
+## Power supply
+
+Input power is delivered via barell plug, `12V 1A` adapter was provided.

machine.c

@@ -176,6 +176,47 @@ __code const struct machine machine = {
 
 void machine_custom_init(void) { }
 
+#elif defined MACHINE_SWTG018AS_A_V_2_0
+__code const struct machine machine = {
+	.machine_name = "SWTG018AS-A V2.0",
+	.isRTL8373 = 1,
+	.min_port = 0,
+	.max_port = 8,
+	.n_sfp = 1,
+	.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
+	.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
+	.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
+	.sfp_port[0].pin_detect = GPIO38,
+	.sfp_port[0].pin_los = GPIO_NA,
+	.sfp_port[0].pin_tx_disable = GPIO_NA,
+	.sfp_port[0].sds = 1,
+	.sfp_port[0].i2c = { .sda = GPIO39_I2C_SDA4, .scl = GPIO40_I2C_SCL3_MDC1 },
+	.reset_pin = GPIO_NA,
+	.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28 | LED_29 },
+	.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1},
+	.led_sets = {
+		{   /* RJ45: First LED, yellow, second LED: green */
+			LEDS_2G5 | LEDS_LINK,
+            LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
+			0,
+			0,
+		}, { /* SFP PORT, SINGLE GREEN LED */
+			LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
+			0,
+			0,
+			0,
+		}},
+	.led_mux_custom = 1,
+	.led_mux = { 0x00, 0x01, 0x04, 0x05, 0x08, // 65e0
+		     0x09, 0x0c, 0x09, 0x0d, 0x10, // 65e4
+		     0x11, 0x0e, 0x14, 0x11, 0x12, // 65e8
+		     0x15, 0x15, 0x16, 0x18, 0x19, // 65ec
+		     0x1a, 0x19, 0x1d, 0x1e, 0x1c, // 65f0
+		     0x1d, 0x20, 0x21 },
+};
+
+void machine_custom_init(void) { }
+
 #elif defined MACHINE_HG0402XG_V1_1
 __code const struct machine machine = {
 	.machine_name = "HG0402XG V1.1",

machine.h

@@ -14,6 +14,7 @@
 // #define MACHINE_HORACO_ZX_SG4T2
 // #define MACHINE_TRENDNET_TEG_S562
 // #define MACHINE_HG0402XG_V1_1
+// #define MACHINE_SWTG018AS_A_V_2_0
 // #define MACHINE_SWTGW218AS
 // #define MACHINE_HI_K0402WS
 // #define MACHINE_DEFAULT_8C_1SFP