Merge pull request #515 from polyfaces/hasivo_s1100wp_8gt_1sx_se

machine: add the Hasivo S1100WP-8GT-1SX-SE target

doc/devices/HASIVO_S1100WP_8GT_1SX_SE.md

@@ -0,0 +1,75 @@
+# Hasivo S1100WP-8GT-1SX-SE
+
+RTL8373-based 8×2.5G PoE + 1×SFP switch.
+
+### Label specifications
+
+- **Manufacturer**: Hasivo
+- **Model**: S1100WP-8GT-1SX-SE
+- **Ports**:
+  - 8 × RJ45: 10/100/1000/2500 Mbps with PoE
+  - 1 × SFP: 1G / 2.5G / 10G
+- **Power input**: DC 52V 2.5A
+- **Stock firmware defaults**: IP 192.168.0.1, user/password `admin`/`admin`
+
+### What works
+
+- All eight 2.5GBASE-T RJ45 ports at 10/100/1000/2500 Mbps (PoE is not configurable via RTLPlayground)
+- SFP port supporting 1G, 2.5G and 10G modules
+- LEDs: green (2.5G) and amber (1G/100M/10M) per copper port; combined link/act on the SFP port
+
+### Photos
+
+Front panel:
+
+<img src="photos/HASIVO_S1100WP-8GT-1SX-SE/front.jpg" width="600" />
+
+Label:
+
+<img src="photos/HASIVO_S1100WP-8GT-1SX-SE/label.jpg" width="600" />
+
+### PCB overview
+
+Top side:
+
+<img src="photos/HASIVO_S1100WP-8GT-1SX-SE/pcb_top.jpg" width="600" />
+
+Bottom side:
+
+<img src="photos/HASIVO_S1100WP-8GT-1SX-SE/pcb_bottom.jpg" width="600" />
+
+### Port layout
+
+| Logical port | Physical port | Type   |
+|--------------|---------------|--------|
+| 1-8          | 1-8           | Copper |
+| 9            | 9             | SFP    |
+
+### LED configuration
+
+Copper ports use LED SET0, the SFP port uses LED SET1.
+
+| SET  | LED0                                          | LED2                                                 |
+|------|-----------------------------------------------|------------------------------------------------------|
+| SET0 | Green — lights on 2.5G link with activity     | Amber — lights on 1G / 100M / 10M link with activity |
+| SET1 | All speeds — lights on any link with activity | —                                                    |
+
+### SFP GPIO assignments
+
+| SFP (logical 9) | pin_detect (ModAbs) | pin_los | pin_tx_disable | SerDes | I2C SDA         | I2C SCL             |
+|-----------------|---------------------|---------|----------------|--------|-----------------|---------------------|
+| SFP             | GPIO30_ACL_BIT3_EN  | GPIO37  | GPIO_NA        | SDS1   | GPIO39_I2C_SDA4 | GPIO40_I2C_SCL3_MDC1 |
+
+### Machine configuration
+
+- `reset_pin`: GPIO54_ACL_BIT2_EN
+- High LEDs (pads 27-29): mux = `LED_27 | LED_28_SYS | LED_29`, enable = `LED_28_SYS | LED_29`
+
+### PoE
+
+The 8 copper ports support PoE powered by a DC 52V 2.5A input. Power management is handled by two HS104PTI chipsets over I2C (GPIO47_I2C_SDA0, GPIO46_I2C_SCL0):
+
+* Chip 1 (I2C address 0x1A): 2.5G Ports 1–4
+* Chip 2 (I2C address 0x2A): 2.5G Ports 5–8
+
+Note: The current implementation does not yet support PoE management. Consequently, PoE currently operates in standalone mode without software control.

doc/supported_devices.md

@@ -7,6 +7,7 @@ The following devices have been tested and are fully working:
 | Davuaz   | Da-K6501W       | No      | [PCB-K0501W-V2.0](devices/K0501W_V2_0.md)                                 |       | 5 + 1 |
 | FOXNEO   | FNS-1200P       | No      | [PCB-K0402W-U13-V2.0](devices/FNS-1200P.md)                               | 2M    | 4 + 2 |
 | Goalake  | IG108           | No      | [PB-2132](devices/PB-2132.md)                                             | 4M    | 8 + 1 |
+| Hasivo   | S1100WP_8GT_1SX_SE | Yes  | [S1100WP_8GT_1SX_SE-V1.05](devices/HASIVO_S1100WP_8GT_1SX_SE.md)          | 2M    | 8 + 1 |
 | Hisource | Hi-K0402WS      | No      | [PCB-K0402WS-V3.0](devices/PCB-K0402WS-V3.0.md)                           |       | 4 + 2 |
 | Hisource | Hi-K0402WS      | No      | [PCB-K0402WS-V2.0](devices/PCB-K0402WS-V2.0.md)                           | 2M    | 4 + 2 |
 | Hisource | Hi-K0801WS      | No      | [PCB-KO801W-V2.0](devices/HI-K0801WS.md)                                  |       | 8 + 1 |

machine.c

@@ -1325,6 +1325,37 @@ __code const struct machine machine = {
     },
 
 };
+#elif defined MACHINE_HASIVO_S1100WP_8GT_1SX_SE
+__code const struct machine machine = {
+	.machine_name = "Hasivo S1100WP-8GT-1SX-SE",
+	.isRTL8373 = 1,
+	.mac_flash_offset = 0x1FC000,
+	.min_port = 0,
+	.max_port = 8,
+	.n_sfp = 1,
+	.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
+	.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
+	.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
+	.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
+	.sfp_port[0].pin_los = GPIO37,
+	.sfp_port[0].pin_tx_disable = GPIO_NA,
+	.sfp_port[0].sds = 1,
+	.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
+	.reset_pin = GPIO54_ACL_BIT2_EN,
+	.high_leds = { .mux = LED_27 | LED_28_SYS | LED_29, .enable = LED_28_SYS | LED_29 },
+	.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1},
+	.led_sets = { { LEDS_2G5 | LEDS_LINK | LEDS_ACT, // Green LED (right)
+					0,
+					LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT, // Amber LED (left)
+					0
+				  },
+				  { LEDS_10G | LEDS_5G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_LINK | LEDS_ACT, // SFP LED
+					0, 
+					0,
+					0
+				  },
+				},
+};
 #elif defined MACHINE_F7008_2_5
 __code const struct machine machine = {
 	.machine_name = "F7008-2.5 8+1 SFP Port Switch",

machine.h

@@ -48,6 +48,7 @@
 // #define MACHINE_POE_2G080110GS
 // #define MACHINE_PB_2132
 // #define MACHINE_HASIVO_S600W_4GT_2XGT_SE
+// #define MACHINE_HASIVO_S1100WP_8GT_1SX_SE
 // #define MACHINE_F7008_2_5
 
 #define LED_27 1