gitproxy/RTLPlayground
1
0 Fork 0
mirror of https://github.com/logicog/RTLPlayground.git synced 2026-10-29 17:54:14 +08:00
Code Issues Packages Projects Releases Wiki Activity
Files
c514eb8bf32cff6a347d8d5a59ef91bf536f0756
RTLPlayground/doc/devices/SWTG024AS.md
T

17 KiB
Raw Blame History

SWTG024AS

SWTG024AS has at least 4 variants that look the same.

Variants are managed and a unmanaged version. But both have pcb version v1.0 and v2.0. Also the RJ45 connectors can be all plastic/non-shielded or with metal shielding.

Brands

Brand Type Managed PCB PCB Label Flash Chip RTL
Binardat 2G06-04210GSM No PCB-SWTG024AS-A-2.0.1 --- 16MB RTL8372N
Horaco ZX-SWTG124AS Yes SWTG024AS-v2.0 ??? ??? 8272
LIANGUO SWTG024AS No SWTG024AS-v2.0-17452 CM-23-11-2336 023-17453 512 KiB 8272
ONT ONT-S207CW-62TS-SE No PCB-SWTG024AS-A-2.0.1 --- 16MB RTL8372N
Sodola SL-SWTG124AS-D Yes SWTG024AS-v2.0-17452 ??? 2048 KiB 8272
Xikestore SKS3200M-4GPY2XF Yes SWTG024AS-v1.0 CM-23-08-2043 023-16721 2048 KiB 8272

PCB

PCB-SWTG024AS-A-2.0.1 Variant

Note: ONT-S207CW-62TS-SE and Binardat 2G06-04210GSM are identical in hardware to this PCB variant. The only difference is the brand label.

Compatible Devices

The following devices use the same PCB-SWTG024AS-A-2.0.1 hardware and are fully compatible with the same firmware configuration:

Brand Model Notes
ONT ONT-S207CW-62TS-SE Original device
Binardat 2G06-04210GSM Identical hardware, same firmware

All these devices can use MACHINE_PCB_SWTG024AS_A_2_0_1 with the LED configuration from this document.

Photos (Binardat 2G06-04210GSM)

Front View:

Back View:

PCB View:

Photos courtesy of andreas5232 from emesix/ONT-S207CW-62TS-SE#1

Hardware Specification

Feature Value
CPU RTL8372N (detected via serial: "Detecting CPU: RTL8372N")
Flash GD25Q128E (16MB)
RAM Integrated in RTL8372N
RJ45 Ports 4x 2.5GBase-T (Ports 1-4)
SFP+ Ports 2x 10G (Ports 5-6)
Console 115200 baud (RTLPlayground firmware) / 9600 baud (stock firmware)
Web UI IP 192.168.2.1
Loader Mode IP 192.168.10.247

Port Layout

┌─────────────────────────────────────────────┐
│  ┌─────┐ ┌─────┐ ┌─────┐ ┌─────┐   ┌─────┐ ┌─────┐  │
│  │RJ45 │ │RJ45 │ │RJ45 │ │RJ45 │   │SFP+ │ │SFP+ │  │
│  │  1  │ │  2  │ │  3  │ │  4  │   │  5  │ │  6  │  │
│  └─────┘ └─────┘ └─────┘ └─────┘   └─────┘ └─────┘  │
│                                                     │
│  [System LEDs]                                      │
└─────────────────────────────────────────────┘

Port Mapping

Physical front panel (left to right):

  • Ports 1-4: RJ45 2.5GBase-T
  • Ports 5-6: SFP+ 10G (Port 5 = left/J4/SFP1, Port 6 = right/J2/SFP2)

RTLPlayground logical mapping:

  • Logical port 3 → Physical SFP1 (J4, left)
  • Logical port 8 → Physical SFP2 (J2, right)
  • Logical ports 4-7 → Physical RJ45 ports 1-4
Physical Port Logical Port Type LED Set Web UI Port
1 4 RJ45 0 1
2 5 RJ45 0 2
3 6 RJ45 0 3
4 7 RJ45 0 4
5 3 SFP+ 1 5
6 8 SFP+ 1 6

LED Behavior (RTLPlayground v10+)

RJ45 Ports (1-4)

LED Color Speed
Green 2.5G
Orange 1G / 100M / 10M
Off No link

SFP+ Ports (5-6)

LED Color Speed
Green 10G
Orange 2.5G / 1G
Off No link / No SFP module

RTLPlayground Configuration

machine.h:

#define MACHINE_PCB_SWTG024AS_A_2_0_1

machine.c configuration:

__code const struct machine machine = {
    .machine_name = "PCB-SWTG024AS-A-2.0.1",
    .isRTL8373 = 0,                    // RTL8372N
    .mac_flash_offset = 0x1FC000,
    .min_port = 3,
    .max_port = 8,
    .n_sfp = 2,
    .log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
    .phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
    .is_sfp = {0, 0, 0, 1, 0, 0, 0, 0, 2},
    
    // SFP port on SDS0 / logical port 3
    .sfp_port[0].pin_detect = GPIO37,
    .sfp_port[0].pin_los = GPIO_NA,
    .sfp_port[0].pin_tx_disable = GPIO_NA,
    .sfp_port[0].sds = 0,
    .sfp_port[0].i2c = { .sda = GPIO41_I2C_SDA3_MDIO1, .scl = GPIO40_I2C_SCL3_MDC1 },
    
    // SFP port on SDS1 / logical port 8
    .sfp_port[1].pin_detect = GPIO38,
    .sfp_port[1].pin_los = GPIO_NA,
    .sfp_port[1].pin_tx_disable = GPIO_NA,
    .sfp_port[1].sds = 1,
    .sfp_port[1].i2c = { .sda = GPIO39_I2C_SDA4, .scl = GPIO40_I2C_SCL3_MDC1 },
    
    .reset_pin = GPIO_NA,
    .high_leds = { .mux = LED_28_SYS | LED_29, .enable = LED_27 | LED_28_SYS | LED_29 },
    .port_led_set = { 0, 0, 0, 1, 0, 0, 0, 0, 1 },
    .led_sets = {
        { // SET0: RJ45 - Green for 2.5G, Orange for 1G/100M/10M
            LEDS_2G5 | LEDS_LINK | LEDS_ACT,
            LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
            0,
            0
        },
        { // SET1: SFP+ - Green for 10G, Orange for 1G/2.5G
            LEDS_10G | LEDS_LINK | LEDS_ACT,
            LEDS_2G5 | LEDS_1G | LEDS_LINK | LEDS_ACT,
            0,
            0
        },
    },
    .led_mux_custom = 1,
    .led_mux = {
        0x00,0x01,0x04,0x05,0x08,0x09,0x0c,0x3f,0x0d,0x10,0x11,0x0e,
        0x14,0x11,0x12,0x15,0x15,0x16,0x18,0x19,0x1a,0x19,0x1d,0x1e,
        0x1c,0x1d,0x20,0x21
    },
};

Firmware History

Version Date Changes Status
v3 2026-09-14 Original PCB_SWTG024AS_A_2_0_1 config All ports working, LEDs wrong
v10 2026-09-17 LED colors corrected for RJ45 and SFP+ All ports + LEDs working

Known Issues & Fixes

Issue: LEDs showing wrong colors

Symptom: RJ45 ports show green at all speeds, SFP LEDs don't light up Fix: Use v10 firmware with corrected LED sets and LED mux configuration

Issue: No network connectivity after flash

Symptom: Switch boots but no ping response Fix: Ensure .isRTL8373 = 0 (RTL8372N) is set - this device uses RTL8372N, not RTL8373

Flashing Instructions

Via Loader Mode (CH341A)

flashrom -p ch341a_spi -c "GD25Q128E" -w rtlplayground-PCB_SWTG024AS_A_2_0_1.bin

Via Web UI

  1. Access the web interface at http://192.168.2.1
  2. Navigate to Firmware Update (under System tab)
  3. Upload rtlplayground_oem_upgrade-PCB_SWTG024AS_A_2_0_1.bin
  4. Wait for flash completion and automatic reboot

Recovery

If flashing fails and the switch does not boot:

  1. Loader Mode Recovery:

    • Hold reset button while powering on
    • Switch should be accessible at 192.168.10.247
    • Flash via curl -T firmware.bin http://192.168.10.247/firmware

  2. Serial Recovery:

    • Connect via UART (115200 baud for RTLPlayground, 9600 for stock)
    • Use CH341A: flashrom -p ch341a_spi -c "GD25Q128E" -w firmware.bin

Stock Firmware Information

  • Default IP: 192.168.10.247
  • Default Login: admin/admin (varies by OEM)
  • Console Baud: 9600
  • CPU: RTL8372N
  • Hardware detection string: "PCB-SWTG024AS-A-2.0.1"

Note: This variant uses the same PCB as described above but may have different component population.

SWTG024AS-v2.0 managed vs unmanaged

Changes I found with my board vs Managed version of the PCB.

Bottom

  • R105: Installed, goes to R10-PullDown SFP2 (J2) -> TX-DISABLE
  • R85: Not Installed (Connected to K1 Reset Button)
  • R90: Not installed (System Led)
  • LED3: Not installed (System Led)

Top

  • K1: Not installed (Reset Button)
  • R95: Installed (SFP2 (J2) signal RX-LOS), means that the managed-version can't use the RX-LOS function.
  • R270: Installed (SFP1 (J4) signal RX-LOS), same here as above.
  • R268: Installed (SFP2 (J2) signal TX-DISABLE, but R262 200R pull-down is to high to drive by the SOC, needs mod!)
  • U5: Flash is only 512 KiB instead of 2/4 MiB.

Notes

  • TX-Disable-SFP2 and Button K1 share the same GPIO pin via R105 and R85. But via R88, TX-Disable-SFP2 can be mapped to GPIO36.
  • TX-Disable pull-down resistos on both SFP are to low to drive by the SOC. We need to make a Best-BOM variant so we can use all the featues.

Connectors

Port overview

┌────────────────────────────────────────────────────────────────────────────────────────┐
│                                                       ┌──────────┐        ┌──────────┐ │
│     ┌─────────┐ ┌─────────┐ ┌─────────┐ ┌─────────┐   │ SFP (J4) │        │ SFP (J2) │ │
│     │  RJ45   │ │  RJ45   │ │  RJ45   │ │  RJ45   │   │ PORT   5 │        │ PORT   6 │ │
│     │  PORT 1 │ │  PORT 2 │ │  PORT 3 │ │  PORT 4 │   │ MAC    8 │        │ MAC    3 │ │
│  O  │  MAC  4 │ │  MAC  5 │ │  MAC  6 │ │  MAC  7 │   │ SerDes 1 │        │ SerDes 0 │ │
│ RST └─────────┘ └─────────┘ └─────────┘ └─────────┘   └──────────┘        └──────────┘ │
└────────────────────────────────────────────────────────────────────────────────────────┘

J4

  • Location: Left SFP connector J4.
  • Connected to: 10GMAC number 8, second SerDes.
J4 SFP1 PINs Signal Component GPIO Notes
2 TX_FAULT B-R262 ---
3 TX_DISABLE B-R263, T-R268 GPIO38 R262 = Pull-down 200R
4 MODDEF2 – SDA B-R261, T-R266 GPIO39
5 MODDEF1 – SCL B-R260, T-R267 GPIO40 Shared with both SFP
6 MODDEF0 – PRESENT B-R259, T-R296 GPIO30
7 RATE SEL B-R257 ---
8 LOS B-R258, T-R270 GPIO37
9 TO? B-R256 ---

J2

  • Location: Right SFP connector J2.
  • Connected to: 10GMAC number 3, first SerDes.
J2 SFP2 PINs Signal Component GPIO Notes
2 TX_FAULT B-R70 ---
3 TX_DISABLE B-R10, B-R105-R, T-R88-L GPIO54 R10 = Pull-down 200R
4 MODDEF2 – SDA B-R26, T-R85 GPIO41
5 MODDEF1 – SCL B-R15, T-R87 GPIO40 Shared with both SFP
6 MODDEF0 – PRESENT B-R14, T-R89 GPIO50
7 RATE SEL B-R12 ---
8 LOS B-R13, T-R95 GPIO51
9 TO? B-R11 ---

Note: component numbering <L>-<REFDES>-<SIDE>

  • L: Layer, T=Top, B=Bottom
  • REFDEES: full silkscreen like R123
  • SIDE: Side of the component. when the rj45 are facing towards you are you can read the silkscreen normal. L = Left, R=right, B=bottom, T=top or P with a pin number.

T3, Slave Interface

This connector goes to U4 I2C EEPROM and U10 SPI FLASH. Signals are based on that U4 is likely a I2C-EEPROM, U10 is likely other SPI-chip.

T3 pin what Signal
1 U4-P6, 33R U10-P6 I2C-SCL, SPI-CLK, Slave SCK/SCL/MDC/EE_SCL
2 GND ---
3 U4-P5, U10-P5 I2C-SDA, SPI-DI/DO, Slave SDI/SDA/MDIO/EE_SDA
4 VCC
5 33R -> U10-P2 SPI-DO/D1
6 U10-P1 SPI-CS
Note: 1 pin is square shaped.

The Slave Interface allows an extenal host to controll the SOC even if the internal MCU is used. Depending on the IF_SEL bootstrap resistors, this can me I2C, SPI or SMI. On this device it is I2C on address 0b1011100 or 0x5c (7-bit notation).

  • I2c Read: must be a write_read opperation <Dev-ADDR><RegAddr15:8><RegAddr7:0> <DevAddr><Data7:0><Data15:8><Data23:16><Data31:24>.
  • I2c Write: <Dev-ADDR><RegAddr15:8><RegAddr7:0><DevAddr><Data7:0><Data15:8><Data23:16><Data31:24>.

Example register 0x0004 return chip id 0x00, 0x00, 0x72, 0x83 = 0x83720000.

T5, serial console

T5 pin GPIO Signal
1 GPIO31 U0TXD (Output)
2 GND
3 GPIO32 U0RXD (Input)
4 3V3
Note: 1 pin is square shaped.

T8

T8 pin what Signal
1 GPIO46
2 GND
3 GPIO48
4 3V3
5 GPIO47
6 GPIO49
Note: 1 pin is square shaped.

Reset ciruit

Cmp Function
T-R78 33k PullUp
T-D3 Discharge Diode
T-C187 RC-Delay

Reset-line found at T-D3-D active-low.

GPIO

HEX VAL. GPIO Component What GPIO Component What
00000001 GPIO00 T-C151-T, T-R28-T, T-R29-T ? GPIO32 T-R143-R U0RXD
00000002 GPIO01 T-C152-T ? GPIO33
00000004 GPIO02 T-C153-T ? GPIO34
00000008 GPIO03 T-R33-T ? GPIO35
00000010 GPIO04 B-C155 ? GPIO36 T-R88-L, T-R84-B Optional SFP2 TX-DISABLE1 , Reset
00000020 GPIO05 B-C156 ? GPIO37 SFP1-8, T-R270 SFP-LOS
00000040 GPIO06 T-C157-T ? GPIO38 SFP1-3, T-R268 SFP1 TX-DISABLE1
00000080 GPIO07 T-C158-T, R165 ? GPIO39 SFP1-4, T-R266 I2C-SDA4
00000100 GPIO08 GPIO40 SFP2-5, T-R87; SFP1-5, T-R267; I2C-SCL
00000200 GPIO09 SFP2-LED, T-R36-T LED-SFP2 GPIO41 SFP2-4, T-R85 I2C-SDA
00000400 GPIO10 GPIO42 U8-P6, T-R124 SPI-MEMORY, CLK
00000800 GPIO11 LEDx2 GPIO43 U8-P5, T-R127 SPI-MEMORY, DI,IO0
00001000 GPIO12 LEDx2 GPIO44 U8-P2, T-R128 SPI-MEMORY, DO,IO1
00002000 GPIO13 PORT1-LED-GREEN LEDx2 GPIO45 U8-P1, T-R123 SPI-MEMORY, CS
00004000 GPIO14 PORT1-LED-YELLOW LEDx GPIO46 T8-1, T-R188 ?
00008000 GPIO15 LEDx2 GPIO47 T8-5, T-R190 ?
00010000 GPIO16 PORT2-LED-GREEN LEDx2 GPIO48 T8-3, T-R189 ?
00020000 GPIO17 PORT2-LED-YELLOW LEDx GPIO49 T8-6, T-R190 ?
00040000 GPIO18 LEDx2 GPIO50 SFP2-6, T-R89 SFP-DETECT
00080000 GPIO19 PORT3-LED-GREEN LEDx2 GPIO51 SFP2-8, T-R95 SFP-LOS
00100000 GPIO20 PORT3-LED-YELLOW LEDx GPIO52
00200000 GPIO21 LEDx2 GPIO53
00400000 GPIO22 PORT4-LED-GREEN LEDx2 GPIO54 SFP2-3, T-R105-L SFP2 TX-DISABLE1 or via T-R85 to RESET3 , T-R84-T
00800000 GPIO23 PORT4-LED-YELLOW LEDx GPIO55 T-R78-B
01000000 GPIO24 SFP1-LED-J4, T-R35 LED-SFP1 GPIO56
02000000 GPIO25 GPIO57
04000000 GPIO26 ? LEDx GPIO58
08000000 GPIO27 R44L ? GPIO59
10000000 GPIO28 LED-SYSTEM, T-R50-R LED-SYSTEM GPIO60
20000000 GPIO29 T-R187-R GPIO61
40000000 GPIO30 SFP1-6, T-R269 SFP-DETECT GPIO62
80000000 GPIO31 T-R144-R U0TXD GPIO63

LEDs

NAME COMPONENTS GPIO Active
SYSTEM T-R50-R (PU-4k2), T-R49-L, T-C185-L, B-R90 GPIO28 Low
SFP1 T-R35-L (PU-3k9), T-R34-L, T-C179-L GPIO24 Low
SFP2 T-R36-T (PD-4k0) GPIO09 High
PORT1-LED-YELLOW GPIO14 Low
PORT2-LED-YELLOW GPIO17 Low
PORT3-LED-YELLOW GPIO20 Low
PORT4-LED-YELLOW GPIO23 Low

Power supply

Board has two supply rails. 0.95 and 3.3 volt.

0.95 Core Voltage.

Voltage is made by a Richtek RT8120A Buck converter. 0.95V must be within 3%.

3.3 Voltage

Voltage is crated by a TMI3244T Buck converter. 3.3V must be within 4.5%. Chip can deliver up to 4A and the sweetspot is at 1A. So higher power SFP-modules should work.

  1. Only on the unmanaged verions are R10 and R268 placed. But the very low pull-down resistor R10 and R262 prevent to SOC to drive does pins. A mod is needed. ↩︎

  2. LEDs are found by just plugin a RJ45 connector and see with cmd gpio the status change. But the bit pattern for port 1,2 are diffrent from port 3,4. ↩︎

  3. GPIO54 is used for the reset-button. T-R85 is placed. ↩︎

Reference in new issue View Git Blame Copy Permalink