mirror of
https://github.com/logicog/RTLPlayground.git
synced 2026-08-30 14:52:51 +08:00
logicog
94d4ace88b
The current code for entering commands via the serial CLI is completely refactored and moved out of rtlplayground.c into a separate file cmd_edit.c putting code into BANK2. The serial ring buffer sbuf[] is now exclusively used for receiving keys, including escape sequences (DEL will generate a 4-byte escape sequence). The command is now held in cmd_buffer. This reduces XMEM use, because the serial buffer can be much smaller. Supported is only editing the current command line via backspace, del, cursor left and right. Because the code cannot distinguish escape sequences which are not yet complete (because the serial isr has not yet put all characters into the serial buffer) from the dozens of unsupported ones (F-keys/home, Page up/down, cursor up/down...) they are ignored and remain in the serial buffer until the ring-pointer overwrites them. This is standard behaviour for consoles, which will print out garbage for unsupported characters. In this implementation, the command line buffer and the visible command line in the terminal are always synced, so garbage can be removed again by ediing the line. The code makes several redundant checks in order to prevent race-conditions between the serial ISR and the comand-editing code.
357 lines
12 KiB
C
357 lines
12 KiB
C
#include "machine.h"
|
|
#include "rtl837x_pins.h"
|
|
#include "rtl837x_leds.h"
|
|
#include "rtl837x_regs.h"
|
|
#include "rtl837x_common.h"
|
|
|
|
#ifdef MACHINE_KP_9000_6XHML_X2
|
|
__code const struct machine machine = {
|
|
.machine_name = "keepLink KP-9000-6XHML-X2",
|
|
.isRTL8373 = 0,
|
|
.min_port = 3,
|
|
.max_port = 8,
|
|
.n_sfp = 2,
|
|
.log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
|
|
.phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
|
|
.is_sfp = {0, 0, 0, 1, 0, 0, 0, 0, 2},
|
|
// Left SFP port (5)
|
|
.sfp_port[0].pin_detect = GPIO50_I2C_SCL2_UART1_TX,
|
|
.sfp_port[0].pin_los = GPIO10_LED10,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 0,
|
|
.sfp_port[0].i2c = { .sda = GPIO41_I2C_SDA3_MDIO1, .scl = GPIO40_I2C_SCL3_MDC1 },
|
|
// Right SFP port (6)
|
|
.sfp_port[1].pin_detect = GPIO30_ACL_BIT3_EN,
|
|
.sfp_port[1].pin_los = GPIO37,
|
|
.sfp_port[1].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[1].sds = 1,
|
|
.sfp_port[1].i2c = { .sda = GPIO39_I2C_SDA4, .scl = GPIO40_I2C_SCL3_MDC1 },
|
|
.reset_pin = GPIO46_I2C_SCL0,
|
|
.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28 | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 0},
|
|
/* Conditions for LED on:
|
|
* dual led orange: ledset_0 & ledset_2
|
|
* dual led green: ledset_2 & !ledset_0
|
|
* single right led green: ledset_0 & !ledset_1
|
|
*/
|
|
.led_sets = { { LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
|
|
LEDS_2G5 | LEDS_LINK | LEDS_10G,
|
|
LEDS_1G | LEDS_LINK,
|
|
0 },
|
|
},
|
|
};
|
|
|
|
void machine_custom_init(void) { }
|
|
|
|
#elif defined MACHINE_KP_9000_6XH_X
|
|
__code const struct machine machine = {
|
|
.machine_name = "keepLink KP-9000-6XH-X",
|
|
.isRTL8373 = 0,
|
|
.min_port = 3,
|
|
.max_port = 8,
|
|
.n_sfp = 1,
|
|
.log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
|
|
.phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
|
|
.sfp_port[0].pin_los = GPIO37,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = { .sda = GPIO39_I2C_SDA4, .scl = GPIO40_I2C_SCL3_MDC1 },
|
|
.reset_pin = GPIO_NA,
|
|
/* Conditions for LED on:
|
|
* dual led orange: ledset_0 & ledset_2
|
|
* dual led green: ledset_2 & !ledset_0
|
|
* single right led green: ledset_0 & !ledset_1
|
|
*/
|
|
.led_sets = { { LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
|
|
LEDS_2G5 | LEDS_LINK | LEDS_10G,
|
|
LEDS_1G | LEDS_LINK,
|
|
0 },
|
|
},
|
|
};
|
|
|
|
void machine_custom_init(void) { }
|
|
|
|
#elif defined MACHINE_KP_9000_9XH_X_EU
|
|
__code const struct machine machine = {
|
|
.machine_name = "keepLink KP-9000-9XH-X-EU",
|
|
.isRTL8373 = 1,
|
|
.min_port = 0,
|
|
.max_port = 8,
|
|
.n_sfp = 1,
|
|
.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
|
|
.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
|
|
.sfp_port[0].pin_los = GPIO37,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = { .sda = GPIO39_I2C_SDA4, .scl = GPIO40_I2C_SCL3_MDC1 },
|
|
.reset_pin = GPIO_NA,
|
|
.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28 | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 0},
|
|
.led_sets = { { LEDS_2G5 | LEDS_TWO_PAIR_1G | LEDS_1G | LEDS_500M | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G | LEDS_TWO_PAIR_5G | LEDS_5G | LEDS_TWO_PAIR_2G5,
|
|
LEDS_2G5 | LEDS_LINK,
|
|
LEDS_1G | LEDS_LINK,
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT },
|
|
},
|
|
};
|
|
|
|
void machine_custom_init(void) { }
|
|
|
|
#elif defined MACHINE_KP_9000_9XHML_X
|
|
__code const struct machine machine = {
|
|
.machine_name = "keepLink KP-9000-9XHML-X",
|
|
.isRTL8373 = 1,
|
|
.min_port = 0,
|
|
.max_port = 8,
|
|
.n_sfp = 1,
|
|
.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
|
|
.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.sfp_port[0].pin_detect = GPIO38,
|
|
.sfp_port[0].pin_los = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = { .sda = GPIO39_I2C_SDA4, .scl = GPIO40_I2C_SCL3_MDC1 },
|
|
.reset_pin = GPIO48_I2C_SCL1,
|
|
.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28 | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.led_sets = {
|
|
{ /* RJ45: First LED, yellow, second LED: green */
|
|
LEDS_2G5 | LEDS_LINK,
|
|
LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
0,
|
|
0,
|
|
}, { /* SFP PORT, SINGLE GREEN LED */
|
|
LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
|
|
0,
|
|
0,
|
|
0,
|
|
}},
|
|
.led_mux_custom = 1,
|
|
.led_mux = {0x00, 0x01, 0x04, 0x05, 0x08, 0x09, 0x0c, 0x09, 0x0d, 0x10,
|
|
0x11, 0x0e, 0x14, 0x11, 0x12, 0x15, 0x15, 0x16, 0x18, 0x19,
|
|
0x1a, 0x19, 0x1d, 0x1e, 0x1c, 0x1d, 0x20, 0x21},
|
|
};
|
|
|
|
void machine_custom_init(void) { }
|
|
|
|
#elif defined MACHINE_SWGT024_V2_0
|
|
__code const struct machine machine = {
|
|
.machine_name = "SWGT024 V2.0",
|
|
.isRTL8373 = 0,
|
|
.min_port = 3,
|
|
.max_port = 8,
|
|
.n_sfp = 2,
|
|
.log_to_phys_port = {0, 0, 0, 6, 1, 2, 3, 4, 5},
|
|
.phys_to_log_port = {4, 5, 6, 7, 8, 3, 0, 0, 0},
|
|
.is_sfp= {0, 0, 0, 2, 0, 0, 0, 0, 1},
|
|
// Left SFP port (J4)
|
|
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
|
|
.sfp_port[0].pin_los = GPIO37,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = { .sda = GPIO39_I2C_SDA4, .scl = GPIO40_I2C_SCL3_MDC1 }, /* GPIO 39 */
|
|
// Right SFP port (J2)
|
|
.sfp_port[1].pin_detect = GPIO50_I2C_SCL2_UART1_TX,
|
|
.sfp_port[1].pin_los = GPIO51_I2C_SDA2_UART1_RX,
|
|
.sfp_port[1].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[1].sds = 0,
|
|
.sfp_port[1].i2c = { .sda = GPIO41_I2C_SDA3_MDIO1, .scl = GPIO40_I2C_SCL3_MDC1 }, /* GPIO 40 */
|
|
.reset_pin = GPIO36_PWM_OUT,
|
|
.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28 | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 0},
|
|
/* Conditions for LED on:
|
|
* dual led orange: ledset_0 & ledset_2
|
|
* dual led green: ledset_2 & !ledset_0
|
|
* single right led green: ledset_0 & !ledset_1
|
|
*/
|
|
.led_sets = { { LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
|
|
LEDS_2G5 | LEDS_LINK | LEDS_10G,
|
|
LEDS_1G | LEDS_LINK,
|
|
0 },
|
|
},
|
|
};
|
|
|
|
void machine_custom_init(void) { }
|
|
|
|
#elif defined MACHINE_HG0402XG_V1_1
|
|
__code const struct machine machine = {
|
|
.machine_name = "HG0402XG V1.1",
|
|
.isRTL8373 = 0,
|
|
.min_port = 3,
|
|
.max_port = 8,
|
|
.n_sfp = 2,
|
|
.log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
|
|
.phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
|
|
.is_sfp = {0, 0, 0, 2, 0, 0, 0, 0, 1},
|
|
.sfp_port[0].pin_detect = 50,
|
|
.sfp_port[0].pin_los = 10,
|
|
.sfp_port[0].pin_tx_disable = 0xFF,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c_bus ={ .sda = GPIO41_I2C_SDA3_MDIO1, .scl = GPIO40_I2C_SCL3_MDC1 },
|
|
.sfp_port[1].pin_detect = 30,
|
|
.sfp_port[1].pin_los = 51,
|
|
.sfp_port[1].pin_tx_disable = 0xFF,
|
|
.sfp_port[1].sds = 0,
|
|
.sfp_port[1].i2c_bus = { .sda = GPIO39_I2C_SDA4, .scl = GPIO40_I2C_SCL3_MDC1 },
|
|
.reset_pin = GPIO_NA,
|
|
.high_leds = { .mux = LED_27 , .enable = LED_27 | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 1, 0, 0, 0, 0, 1},
|
|
/* The Ethernet ports have 1 amber LED (left) and 1 green LED (right)
|
|
* The SFP ports have also 1 amber LED and 1 green LED
|
|
* Ethernet ports use LED-set 0, SFP ports use LED-set 1
|
|
*/
|
|
.led_sets = { { LEDS_10M | LEDS_LINK | LEDS_ACT,
|
|
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_2G5 | LEDS_LINK | LEDS_ACT,
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT,
|
|
0 },
|
|
{ LEDS_100M | LEDS_10M | LEDS_LINK,
|
|
LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
|
|
LEDS_10G | LEDS_LINK,
|
|
0 },
|
|
},
|
|
};
|
|
|
|
void machine_custom_init(void) { }
|
|
|
|
#elif defined MACHINE_SWTGW218AS
|
|
|
|
__code const struct machine machine = {
|
|
.machine_name = "SWTGW218AS 8+1 Managed Switch",
|
|
.isRTL8373 = 1,
|
|
.min_port = 0,
|
|
.max_port = 8,
|
|
.n_sfp = 1,
|
|
.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
|
|
.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
|
|
.sfp_port[0].pin_los = GPIO37,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = { .sda = GPIO39_I2C_SDA4, .scl = GPIO40_I2C_SCL3_MDC1 },
|
|
.reset_pin = GPIO54_ACL_BIT2_EN,
|
|
.high_leds = { .mux = LED_27 | LED_28 | LED_29, .enable = LED_28 | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.led_sets = { { LEDS_2G5 | LEDS_LINK | LEDS_ACT, // Green LED (right)
|
|
0, // unused
|
|
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT, // Amber LED (left)
|
|
0
|
|
}, // unused
|
|
{ LEDS_10G | LEDS_5G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_LINK | LEDS_ACT, // SFP LED
|
|
0, // unused
|
|
0, // unused
|
|
0
|
|
}, // unused },
|
|
},
|
|
};
|
|
|
|
void machine_custom_init(void) { }
|
|
|
|
#elif defined MACHINE_DEFAULT_8C_1SFP
|
|
__code const struct machine machine = {
|
|
.machine_name = "8+1 SFP Port Switch",
|
|
.isRTL8373 = 1,
|
|
.min_port = 0,
|
|
.max_port = 8,
|
|
.n_sfp = 1,
|
|
.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
|
|
.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
|
|
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
|
|
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
|
|
.sfp_port[0].pin_los = GPIO37,
|
|
.sfp_port[0].pin_tx_disable = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = { .sda = GPIO39_I2C_SDA4, .scl = GPIO40_I2C_SCL3_MDC1 },
|
|
.reset_pin = GPIO_NA,
|
|
.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28 | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 0},
|
|
.led_sets = { { LEDS_2G5 | LEDS_TWO_PAIR_1G | LEDS_1G | LEDS_500M | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G | LEDS_TWO_PAIR_5G | LEDS_5G | LEDS_TWO_PAIR_2G5,
|
|
LEDS_2G5 | LEDS_LINK,
|
|
LEDS_1G | LEDS_LINK,
|
|
LEDS_2G5 | LEDS_LINK | LEDS_ACT },
|
|
},
|
|
};
|
|
|
|
void machine_custom_init(void) { }
|
|
|
|
#elif defined MACHINE_TRENDNET_TEG_S562
|
|
__code const struct machine machine = {
|
|
.machine_name = "Trendnet TEG-S562",
|
|
.isRTL8373 = 0,
|
|
.min_port = 3,
|
|
.max_port = 8,
|
|
.n_sfp = 2,
|
|
.log_to_phys_port = {0, 0, 0, 6, 1, 2, 3, 4, 5},
|
|
.phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
|
|
.is_sfp = {0, 0, 0, 2, 0, 0, 0, 0, 1},
|
|
.sfp_port[0].pin_detect = GPIO36_PWM_OUT,
|
|
.sfp_port[0].pin_los = GPIO37,
|
|
.sfp_port[0].pin_tx_disable = GPIO51_I2C_SDA2_UART1_RX,
|
|
.sfp_port[0].sds = 0,
|
|
.sfp_port[0].i2c = { .sda = GPIO47_I2C_SDA0, .scl = GPIO46_I2C_SCL0 },
|
|
.sfp_port[1].pin_detect = GPIO38,
|
|
.sfp_port[1].pin_los = GPIO50_I2C_SCL2_UART1_TX,
|
|
.sfp_port[1].pin_tx_disable = GPIO54_ACL_BIT2_EN,
|
|
.sfp_port[1].sds = 1,
|
|
.sfp_port[1].i2c = { .sda = GPIO49_I2C_SDA1, .scl = GPIO48_I2C_SCL1 },
|
|
.reset_pin = GPIO_NA,
|
|
};
|
|
|
|
void machine_custom_init(void) { }
|
|
|
|
#elif defined MACHINE_HI_K0402WS
|
|
__code const struct machine machine = {
|
|
.machine_name = "HiSource HI-K0402WS",
|
|
.isRTL8373 = 0,
|
|
.min_port = 3,
|
|
.max_port = 8,
|
|
.n_sfp = 2,
|
|
.log_to_phys_port = {0, 0, 0, 6, 1, 2, 3, 4, 5},
|
|
.phys_to_log_port = {4, 5, 6, 7, 8, 3, 0, 0, 0},
|
|
.is_sfp = {0, 0, 0, 2, 0, 0, 0, 0, 1},
|
|
|
|
// Left SFP port
|
|
.sfp_port[0].pin_detect = GPIO38,
|
|
.sfp_port[0].pin_los = GPIO_NA,
|
|
.sfp_port[0].sds = 1,
|
|
.sfp_port[0].i2c = { .sda = GPIO39_I2C_SDA4, .scl = GPIO40_I2C_SCL3_MDC1 },
|
|
|
|
// Right SFP port
|
|
.sfp_port[1].pin_detect = GPIO37,
|
|
.sfp_port[1].pin_los = GPIO_NA,
|
|
.sfp_port[1].sds = 0,
|
|
.sfp_port[1].i2c = { .sda = GPIO41_I2C_SDA3_MDIO1, .scl = GPIO40_I2C_SCL3_MDC1 },
|
|
|
|
.reset_pin = GPIO_NA,
|
|
.high_leds = { .mux = LED_28 | LED_29, .enable = LED_27 | LED_28 | LED_29 },
|
|
.port_led_set = { 0, 0, 0, 1, 0, 0, 0, 0, 1},
|
|
.led_sets = {
|
|
{
|
|
LEDS_2G5 | LEDS_LINK | LEDS_10M | LEDS_ACT,
|
|
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
|
|
LEDS_1G | LEDS_LINK,
|
|
0
|
|
},
|
|
{
|
|
LEDS_10G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK,
|
|
LEDS_10G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_ACT,
|
|
0,
|
|
0
|
|
},
|
|
},
|
|
.led_mux_custom = 1,
|
|
.led_mux = {
|
|
0x00,0x01,0x04,0x05,0x08,0x09,0x0c,0x3f,0x0d,0x10,0x11,0x0e,0x14,0x11,0x12,0x15,0x15,0x16,0x18,0x19,0x1a,0x19,0x1d,0x1e,0x1c,0x1d,0x20,0x21
|
|
},
|
|
};
|
|
|
|
void machine_custom_init(void) {
|
|
reg_bit_set(RTL837X_REG_LED_GLB_IO_EN, 6);
|
|
}
|
|
#else
|
|
#error "Please select a machine type in machine.h"
|
|
#endif
|