mirror of
https://github.com/logicog/RTLPlayground.git
synced 2026-08-30 14:52:51 +08:00
338 lines
9.4 KiB
C
338 lines
9.4 KiB
C
#ifndef _RTL837X_REGS_H_
|
|
#define _RTL837X_REGS_H_
|
|
|
|
#define RTL837X_REG_CHIP_ID 0x0004
|
|
#define RTL837X_REG_CHIP_INFO 0x000c
|
|
#define RTL837X_REG_CHIP_UUID 0x0010
|
|
#define RTL837X_REG_CHIP_LOT_NO 0x0014
|
|
#define RTL837X_REG_RESET 0x0024
|
|
#define RESET_SOC_BIT 0
|
|
#define RESET_NIC_BIT 2
|
|
|
|
#define RTL837X_REG_HW_CONF 0x6040
|
|
// Bits 4 & 5: CLOCK DIVIDER from 125MHz for Timer
|
|
|
|
#define SYS_LED_OFF 0
|
|
#define SYS_LED_FAST 1
|
|
#define SYS_LED_SLOW 2
|
|
#define SYS_LED_ON 3
|
|
|
|
#define RTL837X_REG_LED_MODE 0x6520
|
|
// Defines the LED Mode for steering the Port LEDS and the System LED
|
|
// BIT 17 set: LED solid on
|
|
// Bytes 0/1 hold the LED mode, e.g. serial, RTL8231?
|
|
// Blink rate is defined by setAsicRegBits(0x6520,0xe00000,rate);
|
|
#define RTL837X_REG_LED_GLB_MUX_1 0x65E0
|
|
#define RTL837X_REG_LED_GLB_MUX_2 0x65E4
|
|
#define RTL837X_REG_LED_GLB_MUX_3 0x65E8
|
|
#define RTL837X_REG_LED_GLB_MUX_4 0x65EC
|
|
#define RTL837X_REG_LED_GLB_MUX_5 0x65F0
|
|
#define RTL837X_REG_LED_GLB_MUX_6 0x65F4
|
|
#define RTL837X_REG_LED_GLB_ACTIVE 0x65D8
|
|
#define RTL837X_REG_LED_GLB_IO_EN 0x65DC
|
|
#define RTL837X_REG_LED3_0_SET3 0x6524
|
|
#define RTL837X_REG_LED3_0_SET1 0x6528
|
|
#define RTL837X_REG_LED1_0_SET3 0x6530
|
|
#define RTL837X_REG_LED3_2_SET2 0x6534
|
|
#define RTL837X_REG_LED1_0_SET2 0x6538
|
|
#define RTL837X_REG_LED3_2_SET1 0x653C
|
|
#define RTL837X_REG_LED1_0_SET1 0x6540
|
|
#define RTL837X_REG_LED3_2_SET0 0x6544
|
|
#define RTL837X_REG_LED1_0_SET0 0x6548
|
|
#define RTL837X_LED_PORT_SET_SEL 0x654c
|
|
|
|
// SMI control
|
|
#define RTL837X_REG_SMI_PORT0_5_ADDR 0x644C
|
|
#define RTL837X_REG_SMI_PORT6_9_ADDR 0x6450
|
|
#define RTL837X_REG_SMI_CTRL 0x6454
|
|
#define RTL837X_REG_SMI_MAC_TYPE 0x6330
|
|
#define RTL837X_REG_SMI_PORT_POLLING 0x6334
|
|
|
|
#define RTL837X_REG_SEC_COUNTER 0x06f4
|
|
#define RTL837X_REG_SEC_COUNTER2 0x06f8
|
|
// Used for counting seconds
|
|
|
|
|
|
/*
|
|
* SDS
|
|
*/
|
|
#define RTL837X_SDS_INDACS_CMD 0x3F8
|
|
#define RTL837X_SDS_INDACS_WRITE_DATA 0x400
|
|
#define RTL837X_REG_SDS_MODES 0x7b20
|
|
|
|
/*
|
|
* PHY
|
|
*/
|
|
#define RTL837X_CFG_PHY_TX_POLARITY_SWAP 0xA94
|
|
#define RTL837X_CFG_PHY_MDI_REVERSE 0xA90
|
|
|
|
/*
|
|
* 5 Bits each give the state of the 2 SerDes of the RTL8372
|
|
* Values are:
|
|
*/
|
|
#define SDS_SGMII 0x02
|
|
#define SDS_1000BX_FIBER 0x04
|
|
#define SDS_QXGMII 0x0d
|
|
#define SDS_HISGMII 0x12
|
|
#define SDS_HSG 0x16
|
|
#define SDS_10GR 0x1a
|
|
#define SDS_OFF 0x1f
|
|
|
|
#define RTL837X_REG_LINKS 0x63f0
|
|
#define RTL837X_REG_LINKS_89 0x63f4
|
|
#define RTL837X_REG_LINKS_STS 0x63E8
|
|
|
|
/* Each nibble encodes the link state of a port.
|
|
Port 0 appears to be the CPU port
|
|
The RTL8372 serves ports 4-7, port 3 is the RTL8221
|
|
2: 1Gbit
|
|
5: 2.5Gbit
|
|
*/
|
|
|
|
|
|
/*
|
|
* Pin configuration (pinmux)
|
|
*/
|
|
|
|
#define RTL837X_PIN_MUX_0 0x7f8c
|
|
#define RTL837X_PIN_MUX_1 0x7f90
|
|
#define RTL837X_PIN_MUX_2 0x7f94
|
|
|
|
// Output Registers
|
|
#define RTL837X_REG_GPIO_00_31_OUTPUT 0x3c
|
|
#define RTL837X_REG_GPIO_32_63_OUTPUT 0x40
|
|
// BIT 4 resets RTL8224 on 9000-9XH
|
|
|
|
// Input Registers
|
|
#define RTL837X_REG_GPIO_00_31_INPUT 0x44
|
|
#define RTL837X_REG_GPIO_32_63_INPUT 0x48
|
|
// Bit 1e cleared: SFP Module inserted on 9000-6XH (MOD_DEF0 pin)
|
|
|
|
// BIT 5 set: SIGNAL LOS of SFP module on 9000-6XH (RX_LOS pin)
|
|
|
|
// Direction Registers, 0 = input, 1 = output
|
|
#define RTL837X_REG_GPIO_00_31_DIRECTION 0x4c
|
|
#define RTL837X_REG_GPIO_32_63_DIRECTION 0x50
|
|
|
|
/*
|
|
* I2C controller
|
|
*/
|
|
#define RTL837X_REG_I2C_MST_IF_CTRL 0x0414
|
|
#define RTL837X_REG_I2C_CTRL 0x0418
|
|
#define I2C_DEV_ADDR 3
|
|
#define I2C_MEM_ADDR_WIDTH 20
|
|
#define RTL837X_REG_I2C_CTRL2 0x041c
|
|
#define RTL837X_REG_I2C_IN 0x0420
|
|
#define RTL837X_REG_I2C_OUT 0x0424
|
|
|
|
/*
|
|
* NIC Related registers
|
|
*/
|
|
#define RTL837X_REG_NIC_BUFFSIZE_TX 0x7844
|
|
#define RTL837X_REG_NIC_RXBUFF_RX 0x7848
|
|
#define RTL837X_REG_NIC_RXCMD 0x784c
|
|
#define RTL837X_REG_NIC_TXCMD 0x7850
|
|
#define RTL837X_REG_RX_CTRL 0x785c
|
|
#define RTL837X_REG_TX_CTRL 0x7860
|
|
#define RTL837X_REG_NIC_RX_BUFF_DATA 0x7874
|
|
#define RTL837X_REG_CPU_RX_CURR_PKT 0x787c
|
|
#define RTL837X_REG_NIC_TX_CURR_PKT 0x7884
|
|
#define RTL837X_REG_CPU_TX_CURR_PKT 0x7890
|
|
#define RTL837X_REG_CPU_TAG 0x6720
|
|
#define RTL837X_REG_CPU_TAG_AWARE_PMASK 0x603C
|
|
#define RTL837X_REG_MAC_FORCE_MODE 0x6344
|
|
|
|
/*
|
|
* Statistics related registers
|
|
*/
|
|
#define RTL837X_STAT_GET 0x0f60
|
|
#define RTL837X_STAT_V_HIGH 0x0f64
|
|
#define RTL837X_STAT_V_LOW 0x0f68
|
|
|
|
/*
|
|
* Table access registers of the RTL837x
|
|
* See e.g. RTL8366/RTL8369 datasheet for explanation
|
|
*/
|
|
#define RTL837X_TBL_CTRL 0x5cac
|
|
/* Bytes in control register: EE EE TT CC: EE: Entry, TT: Table type, CC: Command
|
|
* CC: BIT 0: 01: Execute. Bit 1: 1: WRITE, 0: READ
|
|
* TT: 04: L2-table, 03: VLAN-table
|
|
*/
|
|
// Table operation bit-smasks
|
|
#define TBL_WRITE 0x02
|
|
#define TBL_EXECUTE 0x01
|
|
// Table types
|
|
#define TBL_L2_UNICAST 0x04
|
|
#define TBL_VLAN 0x03
|
|
// Table read methods for the L2 table (TBL_L2_UNICAST):
|
|
#define TBL_LUTREAD_MAC 0
|
|
#define TBL_LUTREAD_ADDRESS 1
|
|
#define TBL_LUTREAD_NEXT_ADDRESS 2
|
|
#define TBL_LUTREAD_NEXT_L2UC 3
|
|
#define TBL_LUTREAD_NEXT_L2MC 4
|
|
#define TBL_LUTREAD_NEXT_L3MC 5
|
|
#define TBL_LUTREAD_NEXT_L2L3MC 6
|
|
#define TBL_LUTREAD_NEXT_L2UCSPA 7
|
|
|
|
#define RTL837X_L2_CTRL 0x5350
|
|
#define L2_CTRL_LUT_IPMC_HASH 3
|
|
#define RTL837x_TBL_DATA_0 0x5cb0
|
|
#define RTL837x_L2_DATA_OUT_A 0x5ccc
|
|
#define RTL837x_L2_DATA_OUT_B 0x5cd0
|
|
#define RTL837x_L2_DATA_OUT_C 0x5cd4
|
|
#define RTL837x_TBL_DATA_IN_A 0x5cb8
|
|
#define RTL837x_TBL_DATA_IN_B 0x5cbc
|
|
#define RTL837x_TBL_DATA_IN_C 0x5cc0
|
|
#define RTL837x_PVID_BASE_REG 0x4e1c
|
|
|
|
#define RTL837x_L2_TBL_FLUSH_CTRL 0x53d4
|
|
#define L2_TBL_FLUSH_EXEC 0x10000
|
|
#define RTL837x_L2_TBL_FLUSH_CNF 0x53dc
|
|
#define RTL837X_L2_LRN_PORT_CONSTRAINT 0x5384
|
|
#define RTL837X_L2_LRN_PORT_CONSTRT_ACT 0x4f80
|
|
#define RTL8373_REG_MAC_L2_PORT_MAX_LEN 0x1250
|
|
|
|
/*
|
|
* VLAN configuration
|
|
*/
|
|
#define RTL837X_VLAN_CTRL 0x4e14
|
|
#define VLAN_CVLAN_FILTER 0x4
|
|
#define RTL837X_VLAN_PORT_EGR_TAG 0x6738
|
|
#define RTL837X_VLAN_PORT_IGR_FLTR 0x4e18
|
|
#define RTL837X_VLAN_L2_LRN_DIS_0 0x4e30
|
|
#define RTL837X_VLAN_L2_LRN_DIS_1 0x4e34
|
|
|
|
/*
|
|
* Egress / ingress filtering
|
|
*/
|
|
// 2 bits per port: allow tagged (01) / untagged (10) and all (00)
|
|
#define RTL837x_REG_INGRESS 0x4e10
|
|
#define INGR_ALLOW_TAGGED 1
|
|
#define INGR_ALLOW_UNTAGGED 2
|
|
#define INGR_ALLOW_ALL 0
|
|
|
|
/*
|
|
* Mirroring
|
|
*/
|
|
#define RTL837x_MIRROR_CONF 0x604c
|
|
#define RTL837x_MIRROR_CTRL 0x6048
|
|
|
|
/*
|
|
* Link Aggregation aka Trunking
|
|
*/
|
|
#define RTL837X_TRK_MBR_CTRL_BASE 0x4f38
|
|
#define RTL837X_TRK_HASH_CTRL_BASE 0x4f48
|
|
#define LAG_HASH_SOURCE_PORT_NUMBER 0x01
|
|
#define LAG_HASH_L2_SMAC 0x02
|
|
#define LAG_HASH_L2_DMAC 0x04
|
|
#define LAG_HASH_L3_SIP 0x08
|
|
#define LAG_HASH_L3_DIP 0x10
|
|
#define LAG_HASH_L4_SPORT 0x20
|
|
#define LAG_HASH_L4_DPORT 0x40
|
|
#define LAG_HASH_DEFAULT (LAG_HASH_L2_SMAC | LAG_HASH_L2_DMAC | LAG_HASH_L3_SIP | LAG_HASH_L3_DIP | LAG_HASH_L4_SPORT | LAG_HASH_L4_DPORT)
|
|
|
|
/*
|
|
* Port isolation
|
|
*/
|
|
#define RTL837X_PORT_ISOLATION_BASE 0x50c0
|
|
|
|
/*
|
|
* Multicast handling
|
|
*/
|
|
#define RTL837X_IPV4_PORT_MC_LM_ACT 0x4f78
|
|
#define RTL837X_IPV6_PORT_MC_LM_ACT 0x4f7c
|
|
#define RTL837X_IGMP_PORT_CFG 0x52a0
|
|
#define IGMP_MAX_GROUP 0x00ff0000
|
|
#define IGMP_PROTOCOL_ENABLE 0x00007c00
|
|
#define IGMP_TRAP 0x0000002a
|
|
#define IGMP_FLOOD 0x00000015
|
|
#define IGMP_ASIC 0x00000000
|
|
#define RTL837X_IGMP_ROUTER_PORT 0x529c
|
|
#define RTL837X_IPV4_UNKN_MC_FLD_PMSK 0x5368
|
|
#define RTL837X_IPV6_UNKN_MC_FLD_PMSK 0x536c
|
|
#define RTL837X_IGMP_TRAP_CFG 0x50bc
|
|
#define IGMP_TRAP_PRIORITY 0x7
|
|
#define IGMP_CPU_PORT 0x00010000
|
|
|
|
/*
|
|
* Loop detection / STP
|
|
*/
|
|
#define RTL8373_RLDP_TIMER 0x1074
|
|
#define RTL837X_RMA0_CONF 0x4ecc
|
|
#define RTL837X_RMA_CONF 0x4f1c
|
|
#define RTL837X_MSTP_STATES 0x5310
|
|
#define RTL837X_REG_LED_RLDP_1 0x65F8
|
|
#define RTL837X_REG_LED_RLDP_2 0x65FC
|
|
#define RTL837X_REG_LED_RLDP_3 0x6600
|
|
|
|
/*
|
|
* EEE
|
|
*/
|
|
#define RTL837X_EEE_STATUS 0x125C
|
|
#define RTL837X_MAC_EEE_ABLTY 0x6404
|
|
#define RTL8373_PHY_EEE_ABLTY 0x642C
|
|
#define RTL8373_EEE_CTRL_BASE 0x606c
|
|
#define EEE_100 0x01
|
|
#define EEE_1000 0x04
|
|
#define EEE_2G5 0x10
|
|
#define EEE_NORESET 0x80
|
|
|
|
/*
|
|
* RANDOM
|
|
*/
|
|
#define RTL837X_RLDP_RLPP 0x106C
|
|
#define RLDP_RND_EN 3
|
|
#define RTL837X_RAND_NUM0 0x107C
|
|
#define RTL837X_RAND_NUM1 0x1080
|
|
|
|
/*
|
|
* Bandwidth control
|
|
*/
|
|
#define RTL837X_IGBW_CTRL 0x4c10
|
|
#define IGBW_INC_BYPASS_PKT 0x100
|
|
#define IGBW_INC_IFG 0x80
|
|
#define IGBW_ADM_DHCP 0x20
|
|
#define IGBW_ADM_ARPREQ 0x10
|
|
#define IGBW_ADM_RMA 0x08
|
|
#define IGBW_ADM_BPDU 0x04
|
|
#define IGBW_ADM_RTKPKT 0x02
|
|
#define IGBW_ADM_IGMP 0x01
|
|
#define RTL837X_IGBW_PORT_CTRL 0x4C18
|
|
#define RTL837X_IGBW_PORT_FC_CTRL 0x4C8C
|
|
#define RTL837X_EGBW_PORT_CTRL 0x1c34
|
|
#define RTL837X_EGBW_CTRL 0x447c
|
|
#define EGBW_INC_IFG 0x02
|
|
#define EGBW_CPUMODE 0x01
|
|
|
|
#ifdef REGDBG
|
|
|
|
#define REG_SET(r, v) SFR_DATA_24 = (((uint32_t)v) >> 24) & 0xff; \
|
|
SFR_DATA_16 = (((uint32_t)v) >> 16) & 0xff; \
|
|
SFR_DATA_8 = (((uint16_t)v) >> 8 & 0xff); \
|
|
SFR_DATA_0 = (v) & 0xff; \
|
|
reg_write(r); \
|
|
write_char('R'); print_byte(r >> 8); print_byte(r); write_char('-'); \
|
|
print_byte(((v) >> 24) & 0xff); print_byte((v) >> 16 & 0xff); print_byte((v) >> 8 & 0xff); print_byte( (v) & 0xff); write_char(' ');
|
|
|
|
#define REG_WRITE(r, v24, v16, v8, v0) SFR_DATA_24 = (v24); \
|
|
SFR_DATA_16 = (v16); \
|
|
SFR_DATA_8 = (v8); \
|
|
SFR_DATA_0 = (v0); \
|
|
reg_write(r); \
|
|
write_char('R'); print_byte(r>>8); print_byte(r); write_char('-'); print_byte(v24); print_byte(v16); print_byte(v8); print_byte(v0); write_char(' ');
|
|
#else
|
|
#define REG_SET(r, v) SFR_DATA_24 = (((uint32_t)v) >> 24) & 0xff; \
|
|
SFR_DATA_16 = (((uint32_t)v) >> 16) & 0xff; \
|
|
SFR_DATA_8 = (((uint16_t)v) >> 8 & 0xff); \
|
|
SFR_DATA_0 = (v) & 0xff; \
|
|
reg_write(r);
|
|
|
|
#define REG_WRITE(r, v24, v16, v8, v0) SFR_DATA_24 = (v24); \
|
|
SFR_DATA_16 = (v16); \
|
|
SFR_DATA_8 = (v8); \
|
|
SFR_DATA_0 = (v0); \
|
|
reg_write(r);
|
|
#endif
|
|
|
|
#endif
|