gitproxy/RTLPlayground
1
0
Fork 0
mirror of https://github.com/logicog/RTLPlayground.git synced 2026-08-30 14:52:51 +08:00
Code Issues Packages Projects Releases Wiki Activity
Files
ZX_SWTGW215AS
RTLPlayground/machine.c
T
logicog 347950ff72 Add support for the ZX_SWTGW215AS device built by Hasivo 
The device is sold under the name ZX_SWTGW215AS without necessarily
a Hasivo branding, however the firmware and the PCB are marked with
Hasivo. The PCB is marked Hasivo RTL_SGT-1SX V1.5

SoC: RTL8372
Ethernet: 5 x 2.5GBit (RTL8221B + 4*SoC)
SFP+: 1x 10GBit (SoC)

The device has a slider switch and a reset button.
Reset: GPIO 54 (active-low)
Slider: GPIO 51 (right is high)
2026-02-06 07:19:12 +01:00

239 lines
8.8 KiB
C
Raw Permalink Blame History

#include "machine.h"
#include "rtl837x_pins.h"
#include "rtl837x_leds.h"
#ifdef MACHINE_KP_9000_6XHML_X2
__code const struct machine machine = {
.machine_name = "keepLink KP-9000-6XHML-X2",
.isRTL8373 = 0,
.min_port = 3,
.max_port = 8,
.n_sfp = 2,
.log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
.phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
.is_sfp = {0, 0, 0, 2, 0, 0, 0, 0, 1},
.sfp_port[0].pin_detect = GPIO50_I2C_SCL2_UART1_TX,
.sfp_port[0].pin_los = GPIO10_LED10,
.sfp_port[0].pin_tx_disable = GPIO_NA,
.sfp_port[0].sds = 0,
.sfp_port[0].i2c = { .sda = GPIO41_I2C_SDA3_MDIO1, .scl = GPIO40_I2C_SCL3_MDC1 },
.sfp_port[1].pin_detect = GPIO30_ACL_BIT3_EN,
.sfp_port[1].pin_los = GPIO37,
.sfp_port[1].pin_tx_disable = GPIO_NA,
.sfp_port[1].sds = 1,
.sfp_port[1].i2c = { .sda = GPIO39_I2C_SDA4, .scl = GPIO40_I2C_SCL3_MDC1 },
.reset_pin = GPIO46_I2C_SCL0,
.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28 | LED_29 },
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 0},
/* Conditions for LED on:
* dual led orange: ledset_0 & ledset_2
* dual led green: ledset_2 & !ledset_0
* single right led green: ledset_0 & !ledset_1
*/
.led_sets = { { LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
LEDS_2G5 | LEDS_LINK | LEDS_10G,
LEDS_1G | LEDS_LINK,
0 },
},
.led_mux_custom = 0,
// LED0 LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 LED9 LED10 LED11 LED12 LED13 LED14 LED15
// L-SFP R-SFP | PORT 1
// LED16 LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 LED25 LED26 LED27
// | PORT 2 | PORT 3 | PORT 4
// .led_mux = { 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x0f, 0x0c, 0x0d, 0x0e, 0x10, 0x11, 0x12, 0x14,
// 0x15, 0x16, 0x18, 0x19, 0x1a, 0x1c, 0x1d, 0x1e, 0x20, 0x21, 0x22, 0x23 },
};
#elif defined MACHINE_KP_9000_6XH_X
__code const struct machine machine = {
.machine_name = "keepLink KP-9000-6XH-X",
.isRTL8373 = 0,
.min_port = 3,
.max_port = 8,
.n_sfp = 1,
.log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
.phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
.sfp_port[0].pin_los = GPIO37,
.sfp_port[0].pin_tx_disable = GPIO_NA,
.sfp_port[0].sds = 1,
.sfp_port[0].i2c_bus = { .sda = 4, .scl = 3 },
.sfp_port[0].i2c = { .sda = GPIO39_I2C_SDA4, .scl = GPIO40_I2C_SCL3_MDC1 },
.reset_pin = GPIO_NA,
/* Conditions for LED on:
* dual led orange: ledset_0 & ledset_2
* dual led green: ledset_2 & !ledset_0
* single right led green: ledset_0 & !ledset_1
*/
.led_sets = { { LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
LEDS_2G5 | LEDS_LINK | LEDS_10G,
LEDS_1G | LEDS_LINK,
0 },
},
};
#elif defined MACHINE_KP_9000_9XH_X_EU
__code const struct machine machine = {
.machine_name = "keepLink KP-9000-6XH-X-EU",
.isRTL8373 = 1,
.min_port = 0,
.max_port = 8,
.n_sfp = 1,
.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
.sfp_port[0].pin_los = GPIO37,
.sfp_port[0].pin_tx_disable = GPIO_NA,
.sfp_port[0].sds = 1,
.sfp_port[0].i2c = { .sda = GPIO39_I2C_SDA4, .scl = GPIO40_I2C_SCL3_MDC1 },
.reset_pin = GPIO_NA,
.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28 | LED_29 },
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 0},
.led_sets = { { LEDS_2G5 | LEDS_TWO_PAIR_1G | LEDS_1G | LEDS_500M | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G | LEDS_TWO_PAIR_5G | LEDS_5G | LEDS_TWO_PAIR_2G5,
LEDS_2G5 | LEDS_LINK,
LEDS_1G | LEDS_LINK,
LEDS_2G5 | LEDS_LINK | LEDS_ACT },
},
};
#elif defined MACHINE_SWGT024_V2_0
__code const struct machine machine = {
.machine_name = "SWGT024 V2.0",
.isRTL8373 = 0,
.min_port = 3,
.max_port = 8,
.n_sfp = 2,
.log_to_phys_port = {0, 0, 0, 6, 1, 2, 3, 4, 5},
.phys_to_log_port = {4, 5, 6, 7, 8, 3, 0, 0, 0},
.is_sfp= {0, 0, 0, 2, 0, 0, 0, 0, 1},
// Left SFP port (J4)
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
.sfp_port[0].pin_los = GPIO37,
.sfp_port[0].pin_tx_disable = GPIO_NA,
.sfp_port[0].sds = 1,
.sfp_port[0].i2c = { .sda = GPIO39_I2C_SDA4, .scl = GPIO40_I2C_SCL3_MDC1 }, /* GPIO 39 */
// Right SFP port (J2)
.sfp_port[1].pin_detect = GPIO50_I2C_SCL2_UART1_TX,
.sfp_port[1].pin_los = GPIO51_I2C_SDA2_UART1_RX,
.sfp_port[1].pin_tx_disable = GPIO_NA,
.sfp_port[1].sds = 0,
.sfp_port[1].i2c = { .sda = GPIO41_I2C_SDA3_MDIO1, .scl = GPIO40_I2C_SCL3_MDC1 }, /* GPIO 40 */
.reset_pin = GPIO36_PWM_OUT,
.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28 | LED_29 },
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 0},
/* Conditions for LED on:
* dual led orange: ledset_0 & ledset_2
* dual led green: ledset_2 & !ledset_0
* single right led green: ledset_0 & !ledset_1
*/
.led_sets = { { LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
LEDS_2G5 | LEDS_LINK | LEDS_10G,
LEDS_1G | LEDS_LINK,
0 },
},
};
#elif defined MACHINE_HG0402XG_V1_1
__code const struct machine machine = {
.machine_name = "HG0402XG V1.1",
.isRTL8373 = 0,
.min_port = 3,
.max_port = 8,
.n_sfp = 2,
.log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
.phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
.is_sfp = {0, 0, 0, 2, 0, 0, 0, 0, 1},
.sfp_port[0].pin_detect = 50,
.sfp_port[0].pin_los = 10,
.sfp_port[0].pin_tx_disable = 0xFF,
.sfp_port[0].sds = 1,
.sfp_port[0].i2c_bus ={ .sda = GPIO41_I2C_SDA3_MDIO1, .scl = GPIO40_I2C_SCL3_MDC1 },
.sfp_port[1].pin_detect = 30,
.sfp_port[1].pin_los = 51,
.sfp_port[1].pin_tx_disable = 0xFF,
.sfp_port[1].sds = 0,
.sfp_port[1].i2c_bus = { .sda = GPIO39_I2C_SDA4, .scl = GPIO40_I2C_SCL3_MDC1 },
.reset_pin = GPIO_NA,
.high_leds = { .mux = LED_27 , .enable = LED_27 | LED_29 },
.port_led_set = { 0, 0, 0, 1, 0, 0, 0, 0, 1},
/* The Ethernet ports have 1 amber LED (left) and 1 green LED (right)
* The SFP ports have also 1 amber LED and 1 green LED
* Ethernet ports use LED-set 0, SFP ports use LED-set 1
*/
.led_sets = { { LEDS_10M | LEDS_LINK | LEDS_ACT,
LEDS_1G | LEDS_100M | LEDS_10M | LEDS_2G5 | LEDS_LINK | LEDS_ACT,
LEDS_2G5 | LEDS_LINK | LEDS_ACT,
0 },
{ LEDS_100M | LEDS_10M | LEDS_LINK,
LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
LEDS_10G | LEDS_LINK,
0 },
},
};
#elif defined MACHINE_ZX_SWTGW215AS_HASIVO
__code const struct machine machine = {
.machine_name = "ZX-SWTGW215AS HASIVO",
.isRTL8373 = 0,
.min_port = 3,
.max_port = 8,
.n_sfp = 1,
.log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
.phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
.sfp_port[0].pin_los = GPIO37,
.sfp_port[0].pin_tx_disable = GPIO_NA,
.sfp_port[0].sds = 1,
.sfp_port[0].i2c = { .sda = GPIO39_I2C_SDA4, .scl = GPIO40_I2C_SCL3_MDC1 },
.sfp_port[1].i2c = { .sda = GPIO39_I2C_SDA4, .scl = GPIO40_I2C_SCL3_MDC1 },
.reset_pin = GPIO54_ACL_BIT2_EN,
.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28 | LED_29 },
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1},
.led_sets = {
/* The Ethernet ports have 1 amber LED (bi-color left) and 2 green LED (left/right)
* The SFP port has 1 green LED
* Ethernet ports use LED-set 0, SFP port uses LED-set 1
* Amber-LED: ledid0 & ledid1 & !ledid2
* Left-Green: ledid-2
* Right-Green: ledid-0
* ledid3 is not used
*/
{ LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G,
LEDS_2G5 | LEDS_LINK | LEDS_10G,
LEDS_1G | LEDS_LINK,
0 },
{
LEDS_2G5 | LEDS_TWO_PAIR_1G | LEDS_1G | LEDS_500M | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G | LEDS_TWO_PAIR_5G | LEDS_5G | LEDS_TWO_PAIR_2G5,
LEDS_1G | LEDS_LINK,
LEDS_2G5 | LEDS_LINK,
LEDS_COL | LEDS_DUPLEX,
}
},
.led_mux_custom = 0,
};
#elif defined DEFAULT_8C_1SFP
__code const struct machine machine = {
.machine_name = "8+1 SFP Port Switch",
.isRTL8373 = 1,
.min_port = 0,
.max_port = 8,
.n_sfp = 1,
.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
.sfp_port[0].pin_los = GPIO37,
.sfp_port[0].pin_tx_disable = GPIO_NA,
.sfp_port[0].sds = 1,
.sfp_port[0].i2c = { .sda = GPIO39_I2C_SDA4, .scl = GPIO40_I2C_SCL3_MDC1 },
.reset_pin = GPIO_NA,
.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28 | LED_29 },
.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 0},
.led_sets = { { LEDS_2G5 | LEDS_TWO_PAIR_1G | LEDS_1G | LEDS_500M | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT | LEDS_10G | LEDS_TWO_PAIR_5G | LEDS_5G | LEDS_TWO_PAIR_2G5,
LEDS_2G5 | LEDS_LINK,
LEDS_1G | LEDS_LINK,
LEDS_2G5 | LEDS_LINK | LEDS_ACT },
},
};
#endif
Reference in New Issue View Git Blame Copy Permalink