Merge pull request #597 from DrDoof/web/port-strip-topbar

web: keep the port strip in the header on every tab

Makefile

@@ -99,6 +99,7 @@ SRCS = \
 # RTL837x
 SRCS += \
 	rtl837x_bandwidth.c \
+	rtl837x_cabletest.c \
 	rtl837x_flash.c \
 	rtl837x_igmp.c \
 	rtl837x_init.c \

README.md

@@ -103,24 +103,29 @@ docker run --rm -p 8080:8080 -v $(pwd):/workspace rtlplayground-dev \
   tools/output/httpd_sim /workspace/html
 ```
 
-Edit `machine.h` or `config.txt` on your host, then re-run `make` — the
+Edit `config.txt` on your host, then re-run `make` — the
 source directory is mounted into the container, so changes take effect
-immediately. To build for a different machine, pass `MACHINE=...`.
+immediately. To build for a different machine, pass `MACHINE=<name>`, which
+selects `machine/<name>.c` (see [Adding a new device](doc/adding-a-device.md)).
 
 </details>
 
 ## (1) Compiling for direct chip flashing AND upgrading an existing RTLPlayground running device
 
-Edit machine.h with an editor like vi or nano. Select the correct machine the firmware should build for.
+Pass the machine that matches your device, for example:
+```
+make MACHINE=DEFAULT_8C_1SFP
+```
+The name selects the board definition `machine/<name>.c`; `make` without a
+`MACHINE` value stops with an error listing what is expected. If your board is
+not in the list yet, see [Adding a new device](doc/adding-a-device.md).
 
 > [!TIP]
 > You can write configuration parameters in config.txt (see below) in order your switch to get
 > straight at the first boot, a correct IP configuration.
 
-Now, building the firmware image should work:
+Now, building the firmware image should work.
-```
+
-make 
-```
 Note, that the image generated ends in .bin, not .img, in order to make IMSProg happy.
 
 image location is stored in `RTLPlayground/output/rtlplayground_version_machine.bin`
@@ -353,6 +358,7 @@ Enjoy playing!
 ## (11) Other documents
 
 The following documents give further documentation on specific features of the RTL837x SoCs:
+- [Adding a new device](doc/adding-a-device.md)
 - [RTL8372/3 Feature support](doc/hardware.md)
 - [CPU Port](doc/CpuPort.md)
 - [L2 learning](doc/l2.md) 

cmd_parser.c

@@ -20,6 +20,7 @@
 #include "rtl837x_lldp.h"
 #include "rtl837x_storm.h"
 #include "rtl837x_trap.h"
+#include "rtl837x_cabletest.h"
 #include "sfp.h"
 #include "dhcp.h"
 #include "syslog.h"
@@ -166,10 +167,15 @@ uint8_t atoi_hex(uint8_t idx)
 			break;
 		}
 
+		if (h_idx == 8) {
+			h_idx = 0;
+			break;
+		}
+
 		// swap hex nibbles
 		val = (val >> 4) | (val << 4);
 
-		if (c - '0' < 10) {
+		if ((uint8_t)(c - '0') < 10) {
 			val |= c - '0';
 		} else {
 			c |= 0x20;
@@ -903,6 +909,7 @@ void parse_port(void)
 					 "\nport <port> [show|on|off]" \
 					 "\nport <port> [10m|100m|1g|2g5|duplex] [half|full]" \
 					 "\nport <port> lldp [block|permit]" \
+					 "\nport <port> cabletest [show]" \
 					 "\nport <port> name [custom port name]\n");
 		return;
 	}
@@ -945,6 +952,11 @@ void parse_port(void)
 		}
 	} else if (machine.is_sfp[phy_settings.port]) {
 		print_string(" is SFP no PHY information available.\n");
+	} else if (cmd_compare(2, "cabletest")) {
+		if (cmd_words_len > 3 && cmd_compare(3, "show"))
+			cabletest_show();
+		else
+			cabletest_run();
 	} else if (cmd_compare(2, "10m")) {
 		print_string(" 10M\n");
 		phy_settings.speed = PHY_SPEED_10M;
@@ -2143,7 +2155,7 @@ void execute_config(void) __banked
 				skipping = 1;
 			}
 			c = flash_buf[cfg_idx++];
-			if (c == 0 || c == '\n') {
+			if (c == 0 || c == '\n' || c == '\r') {
 				if (skipping) {
 					skipping = 0;
 				} else {

doc/adding-a-device.md

@@ -0,0 +1,179 @@
+# Adding a new device
+
+A device is supported by adding one board definition `.h` and board configuration `.c` file
+under `machine/`. 
+the build selects the definition by name, and CI compiles every file it finds.
+
+To compile for your added device, do:
+```
+make MACHINE=<NAME>
+```
+
+## What a new device consists of
+
+| File | Purpose |
+|------|---------|
+| `machine/<NAME>.c` | the `struct machine machine` board definition |
+| `machine/<NAME>.h` | `MACHINE_MODEL`, the model string shown in the UI and the CLI |
+| `doc/devices/<name>.md` + `doc/supported_devices.md` | (only if the board is verified and you want to support it publicly) user-facing documentation |
+
+`<NAME>` is the machine symbol without its `MACHINE_` prefix, so `MACHINE` is
+passed exactly as spelled on the command line: `make MACHINE=MY_BOARD_1_0`
+needs `machine/MY_BOARD_1_0.c` and `machine/MY_BOARD_1_0.h`.
+
+## Step 1: the model header
+
+`machine/<NAME>.h` only carries the product string. Use the existing files as
+the template:
+
+```c
+#ifndef _MACHINE_MY_BOARD_1_0_H_
+#define _MACHINE_MY_BOARD_1_0_H_
+
+#define MACHINE_MODEL "Brand Model V1.0"
+
+#endif
+```
+
+The device product string is what the CLI or the Web-Interface will print to identify the device; `machine.h` includes it by name.
+
+> [!NOTE]
+> `machine_name` is a `char[30]` and `MACHINE_MODEL` is copied into it at
+> compile time. A longer model string still builds, but SDCC emits
+> `warning 147: excess elements in array of chars initializer` and the name is
+> truncated in the UI. Keep it to 29 characters or less.
+
+## Step 2: the board definition
+
+`machine/<NAME>.c` starts with the shared prelude and then defines the single
+`machine` object. Copy the closest existing board and adjust it — do not start
+from a blank file, the field meanings are easier to see in a real example.
+The best choice is usually a device that has the same number and type of Ethernet
+ports and the same number of SFP+ cages.
+
+```c
+#include "machine_defs.h"
+
+__code const struct machine machine = {
+	.machine_name = MACHINE_MODEL,
+	.isRTL8373 = 1,
+	.min_port = 0,
+	.max_port = 8,
+	.n_sfp = 1,
+	.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
+	.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
+	.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
+
+	.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
+	.sfp_port[0].pin_los = GPIO37,
+	.sfp_port[0].pin_tx_disable = GPIO_NA,
+	.sfp_port[0].sds = 1,
+	.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
+	.reset_pin = GPIO_NA,
+
+	.high_leds = { .mux = LED_27 | LED_29, .enable = LED_28_SYS | LED_29 },
+	.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1 },
+	.led_sets = {
+		{   /* RJ45 ports */
+			LEDS_2G5 | LEDS_LINK,
+			LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
+			0,
+			0
+		}, { /* SFP port, single green LED */
+			LEDS_10G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
+			0,
+			0,
+			0
+		}
+	},
+};
+```
+
+### Fields
+
+| Field | Meaning |
+|-------|---------|
+| `machine_name` | always `MACHINE_MODEL` |
+| `isRTL8373` | `1` for an RTL8373 SoC, `0` for RTL8372 |
+| `min_port` / `max_port` | range of logical port numbers the device has; `min_port` is `0` for RTL8373 boards and `3` for RTL8372 boards (logical ports 1–2 are the SoC's internal ports on the 8372), `max_port` is usually 8. |
+| `n_sfp` | number of SFP+ cages |
+| `n_10g` | SerDes 10G capability used by the RTL837xN init: `0` none, `1` one, `2` two 10G-capable SerDes |
+| `log_to_phys_port[9]` | logical port (0-based index) → physical front-panel port number |
+| `phys_to_log_port[9]` | the inverse, physical port 1 is index 0, unused slots are 0 |
+| `is_sfp[9]` | `0` for copper, `1` for left slot and `2` for right slot |
+| `sfp_port[2]` | per-cage wiring, `sfp_port[0]` is the leftmost cage |
+| `reset_pin` | GPIO of the reset button, `GPIO_NA` if unpopulated |
+| `high_leds` | mux/enable for the LED pins 27–29 (`LED_27`, `LED_28_SYS`, `LED_29`) |
+| `port_led_set[9]` | which LED set (0–3) each logical port uses |
+| `led_sets[4][4]` | Each port can have up to 4 GPIO output pins assigned. 4 sets of LEDs with 4 LED-conditions per set; the conditions define which GPIO pins become active for a port given a port link-state. Which LEDs are then enabled depends on the wiring of the pins to up to 3 LEDs for that port, which can make a logical combination of the 4 LED output-pins. |
+| `led_mux_custom` / `led_mux[28]` | `1` plus the 28 mux values when the stock LED muxing does not fit the board |
+| `mac_flash_offset` | flash offset of the factory MAC address, omit or `0` if the board does not store one |
+
+Each `struct sfp_port` entry holds `pin_detect`, `pin_los`, `pin_tx_disable`,
+`sds` (which SerDes drives the cage) and `i2c` (built with `I2CBUS(sda, scl)`,
+or `GPIO_NA`-based values where a cage has no such pin).
+
+`I2CBUS(...)` only accepts the pin pairs listed in `machine_defs.h`. A wrong
+pair is caught at compile time: SDCC reports
+`error 176: sizeof applied to an incomplete type` pointing at the offending
+`.i2c` line, because the macro deliberately turns an invalid bus number into an
+array of size 0.
+
+### Reusing an existing definition
+
+If the new board is electrically identical to one that already exists — same
+port mapping, same SFP wiring, same LEDs — do not copy the file. Make the new
+`.c` a symlink and keep only a distinct `.h`, so the two boards cannot drift
+apart:
+
+```
+ln -s KP_9000_6XHML_X2.c machine/MY_BOARD_1_0.c
+```
+
+The new board still needs `machine/MY_BOARD_1_0.h` (pick the version number on the PCB) with its own
+`MACHINE_MODEL`, because `MACHINE_MODEL` is what distinguishes the products.
+Existing examples: `machine/PCB_K0402WS_V3.c`, `machine/KP_9000_9XHML_X_V3_2.c`
+and the six `KP_9000_*` revision variants.
+
+Two files that differ only in whitespace or comments are duplicates and should
+be collapsed this way.
+
+## Step 3: build and verify
+
+```
+make MACHINE=MY_BOARD_1_0
+```
+
+The generated flash image appears as `output/rtlplayground-<version>-MY_BOARD_1_0.bin`. An
+unknown or empty `MACHINE` fails immediately with a message naming the expected
+file, before anything is compiled.
+
+Then run the checks CI runs:
+
+```
+make machine_check    # compiles machine/<NAME>.c and machine_init.c for every machine
+make -C test          # host-side unit tests
+```
+
+`make machine_check` discovers the definitions with
+`$(wildcard machine/*.c)`, so a new file is covered without registering it
+anywhere. CI (`.github/workflows/build.yml`) runs it on every push and pull
+request, alongside full builds for a 4+2 and an 8+1 board.
+
+A successful compile only proves the definition is syntactically valid. The
+actual behaviour — port numbering, SFP detection, LEDs — has to be confirmed on
+hardware, and the console commands (`port`, `stat`, `sfp`, `leds`) are the
+tools for that.
+
+## Step 4: documentation
+
+Once the board has been tested on hardware:
+
+1. Add a row to the table in [Supported devices](supported_devices.md).
+2. Add `doc/devices/<name>.md` describing the board, the build target
+   (`make MACHINE=MY_BOARD_1_0`), what works and what is unverified, plus
+   photos and the PCB silkscreen marking.
+3. If the board shares a PCB with other revisions, follow
+   `doc/devices/KP-9000-6XH-X2.md` and document which `MACHINE` to pick for
+   which silkscreen.
+

doc/devices/2M-PCB23-V3_2.md

@@ -17,8 +17,8 @@ The original web interface reports this board as hardware version V3.2
 The component placement matches [2M-PCB23-V3.1](2M-PCB23-V3_1.md): same
 positions for the flash (U8), the T7/T8/T9/T10 headers, the SFP cage and its
 LED, and the unpopulated U7/U9 footprints. Build with
-`MACHINE=KP_9000_9XHML_X_V3_2`, which uses the V3.1 machine definition and
+`make MACHINE=KP_9000_9XHML_X_V3_2`, whose board file is a symlink to the V3.1
-only differs in the reported name.
+definition and only differs in the reported name.
 
 ## Tested
 

doc/devices/2M-PCB43-V1.1.md

@@ -15,7 +15,7 @@ and sold by Mokerlink.
 The device is fully supported:
 - All 4 2.5GBASE-T RJ45 ports work at 10/100/1000/2500 Mbps
 - The SFP+ port supports 1G, 2.5G and 10G modules 
-- LEDs work with the same indiciations as the OEM firmware (use KP_9000_6XHML_X2_V1_1 in machine.h if building yourself or the corresponding pre-compiled binary)
+- LEDs work with the same indiciations as the OEM firmware (build with `make MACHINE=KP_9000_6XHML_X2_V1_1` if building yourself, or use the corresponding pre-compiled binary)
 - untested due to missing Hardware: SFP+ ports equipped with 1G or 2.5G SFPs.
 
 ### Hardware overview

doc/devices/SWTG024AS-A-V2.0.1_4C_2SFP.md

@@ -5,6 +5,7 @@ It is highly similar to SWTG024AS-V2.0, with the only difference being the GPIO
 |Brand|Type|Managed|PCB|Flash|Chip RTL|
 |---|---|---|---|---|---|
 | Horaco | ZX-SG4T2 |  | PCB-SWTG024AS-A-V2.0.1_19650 | P25D40SH | ??? |
+| GoodTop | GT-ST024M | Yes | PCB-SWTG024AS-A-V2.0.1 | 2M | ??? |
 
 ### Label specifications
 

doc/devices/SWTGW215AS.md

@@ -9,7 +9,7 @@
 
 ## RTLPlayground target
 
-Use machine target `MACHINE_LIANGUO_ZX_SWTGW215AS` for this device.
+Build for this device with `make MACHINE=LIANGUO_ZX_SWTGW215AS`, which selects the `machine/LIANGUO_ZX_SWTGW215AS.c` board definition.
 
 Physical hardware verification: 5x RJ45 ports + 1x SFP port. 
 Port 5 RJ45 is interfaced through a RTL8221B IC.

doc/supported_devices.md

@@ -8,6 +8,7 @@ The following devices have been tested and are fully working:
 | FOXNEO   | FNS-1200P       | No      | [PCB-K0402W-U13-V2.0](devices/FNS-1200P.md)                               | 2M    | 4 + 2 |
 | Goalake  | IG108           | No      | [PB-2132](devices/PB-2132.md)                                             | 4M    | 8 + 1 |
 | GoodTop  | GT-ST018M       | Yes     | [SWTG018AS-A V2.0](devices/SWTG018AS_A_V2_0.md)                           | ?     | 8 + 1 |
+| GoodTop  | GT-ST024M       | Yes     | [SWTG024AS-A V2.0.1](devices/SWTG024AS-A-V2.0.1_4C_2SFP.md)                           | 2M    | 4 + 2 |
 | Hasivo   | S1100WP_8GT_1SX_SE | Yes  | [S1100WP_8GT_1SX_SE-V1.05](devices/HASIVO_S1100WP_8GT_1SX_SE.md)          | 2M    | 8 + 1 |
 | Hisource | Hi-K0402WS      | No      | [PCB-K0402WS-V3.0](devices/PCB-K0402WS-V3.0.md)                           |       | 4 + 2 |
 | Hisource | Hi-K0402WS      | No      | [PCB-K0402WS-V2.0](devices/PCB-K0402WS-V2.0.md)                           | 2M    | 4 + 2 |

html/app.js

@@ -11,15 +11,15 @@ th_sel_light:"Selenized Light",th_sel_dark:"Selenized Dark",
 c_port:"Port",c_name:"Name",c_link:"Link",c_apply:"Apply",c_cancel:"Cancel",c_confirm:"Confirm",
 c_close:"Close",c_refresh:"Refresh",c_off:"off",c_offc:"Off",c_down:"down",c_on:"On",c_auto:"Auto",c_delete:"Delete",
 c_type:"Type",c_state:"State",c_enabled:"Enabled",c_load:"Load",c_disable:"Disable",c_sfp:"SFP",
-c_full:"full",c_half:"half",c_devices:"devices",c_yes:"yes",c_no:"no",
+c_full:"full",c_half:"half",c_yes:"yes",c_no:"no",
-d_ports:"Ports",d_ports_h:"click a port for details",d_system:"System",d_traffic:"Traffic",
+d_system:"System",d_traffic:"Traffic",
 d_traffic_h:"packets/s, live",d_txpps:"TX pps",d_rxpps:"RX pps",d_txbad:"TX bad",d_rxbad:"RX bad",
 i_host:"Hostname",i_ip:"IP address",i_mask:"Netmask",i_gw:"Gateway",i_mac:"MAC",i_fw:"Firmware",
 i_built:"Built",i_hw:"Hardware",i_temp:"Temperature",i_flash:"Flash",i_syslog:"Syslog",
 p_state:"State",p_disabled:"disabled",p_up:"up",p_txgb:"TX good / bad",p_rxgb:"RX good / bad",
 p_pkts:"pkts",p_module:"Module",p_temp:"Temperature",p_vcc:"Vcc",p_txbias:"TX bias",p_txpower:"TX power",
 p_rxpower:"RX power",p_txfault:"TX fault",p_txdis:"TX disabled",p_rxlos:"RX LOS",p_adv:"Advertising",
-pt_title:"Port configuration",pt_conn:"Connected",pt_speed:"Speed",pt_mtu:"MTU",
+pt_title:"Port configuration",pt_conn:"Devices learned",pt_speed:"Speed",pt_mtu:"MTU",
 pt_sfp_note:"SFP speed is set per slot and is not saved in the startup config.",
 pt_name_err:"Port name: 1-15 characters, no spaces",pt_mtu_err:"MTU must be 64-16383",
 stp_title:"Spanning tree",stp_h:"RSTP, 802.1w",stp_version:"Version",stp_v_stp:"STP compatible",
@@ -142,15 +142,15 @@ th_sel_light:"Selenized ライト",th_sel_dark:"Selenized ダーク",
 c_port:"ポート",c_name:"名前",c_link:"リンク",c_apply:"適用",c_cancel:"キャンセル",c_confirm:"確認",
 c_close:"閉じる",c_refresh:"更新",c_off:"オフ",c_offc:"オフ",c_down:"リンクダウン",c_on:"オン",c_auto:"自動",c_delete:"削除",
 c_type:"タイプ",c_state:"状態",c_enabled:"有効",c_load:"読み込み",c_disable:"無効化",c_sfp:"SFP",
-c_full:"全二重",c_half:"半二重",c_devices:"デバイス",c_yes:"はい",c_no:"いいえ",
+c_full:"全二重",c_half:"半二重",c_yes:"はい",c_no:"いいえ",
-d_ports:"ポート",d_ports_h:"ポートをクリックすると詳細を表示",d_system:"システム",d_traffic:"トラフィック",
+d_system:"システム",d_traffic:"トラフィック",
 d_traffic_h:"パケット/秒、リアルタイム",d_txpps:"TX pps",d_rxpps:"RX pps",d_txbad:"TX 異常",d_rxbad:"RX 異常",
 i_host:"ホスト名",i_ip:"IP アドレス",i_mask:"ネットマスク",i_gw:"ゲートウェイ",i_mac:"MAC",i_fw:"ファームウェア",
 i_built:"ビルド日",i_hw:"ハードウェア",i_temp:"温度",i_flash:"フラッシュ",i_syslog:"Syslog",
 p_state:"状態",p_disabled:"無効",p_up:"アップ",p_txgb:"TX 正常 / 異常",p_rxgb:"RX 正常 / 異常",
 p_pkts:"pkts",p_module:"モジュール",p_temp:"温度",p_vcc:"電圧",p_txbias:"TX バイアス",p_txpower:"TX 電力",
 p_rxpower:"RX 電力",p_txfault:"TX 障害",p_txdis:"TX 無効",p_rxlos:"RX 信号ロス",p_adv:"アドバタイズ",
-pt_title:"ポート設定",pt_conn:"接続デバイス",pt_speed:"速度",pt_mtu:"MTU",
+pt_title:"ポート設定",pt_conn:"学習済みデバイス",pt_speed:"速度",pt_mtu:"MTU",
 pt_sfp_note:"SFP の速度はスロット単位で設定され、起動設定には保存されません。",
 pt_name_err:"ポート名: 1〜15 文字、空白不可",pt_mtu_err:"MTU は 64〜16383 の範囲で指定してください",
 stp_title:"スパニングツリー",stp_h:"RSTP, 802.1w",stp_version:"バージョン",stp_v_stp:"STP 互換",
@@ -255,15 +255,15 @@ th_sel_light:"Selenized 浅色",th_sel_dark:"Selenized 深色",
 c_port:"端口",c_name:"名称",c_link:"链路",c_apply:"应用",c_cancel:"取消",c_confirm:"确认",
 c_close:"关闭",c_refresh:"刷新",c_off:"关",c_offc:"关",c_down:"未连接",c_on:"开",c_auto:"自动",c_delete:"删除",
 c_type:"类型",c_state:"状态",c_enabled:"启用",c_load:"读取",c_disable:"禁用",c_sfp:"SFP",
-c_full:"全双工",c_half:"半双工",c_devices:"台设备",c_yes:"是",c_no:"否",
+c_full:"全双工",c_half:"半双工",c_yes:"是",c_no:"否",
-d_ports:"端口",d_ports_h:"点击端口查看详情",d_system:"系统",d_traffic:"流量",
+d_system:"系统",d_traffic:"流量",
 d_traffic_h:"包/秒，实时",d_txpps:"TX pps",d_rxpps:"RX pps",d_txbad:"TX 错误",d_rxbad:"RX 错误",
 i_host:"主机名",i_ip:"IP 地址",i_mask:"子网掩码",i_gw:"网关",i_mac:"MAC",i_fw:"固件",
 i_built:"构建日期",i_hw:"硬件",i_temp:"温度",i_flash:"Flash",i_syslog:"Syslog",
 p_state:"状态",p_disabled:"已禁用",p_up:"已连接",p_txgb:"TX 正常 / 错误",p_rxgb:"RX 正常 / 错误",
 p_pkts:"个包",p_module:"模块",p_temp:"温度",p_vcc:"供电电压",p_txbias:"TX 偏置电流",p_txpower:"TX 光功率",
 p_rxpower:"RX 光功率",p_txfault:"TX 故障",p_txdis:"TX 禁用",p_rxlos:"RX 信号丢失",p_adv:"通告能力",
-pt_title:"端口配置",pt_conn:"已连接设备",pt_speed:"速率",pt_mtu:"MTU",
+pt_title:"端口配置",pt_conn:"已学习设备",pt_speed:"速率",pt_mtu:"MTU",
 pt_sfp_note:"SFP 速率按插槽设置，不会保存到启动配置。",
 pt_name_err:"端口名称: 1-15 个字符，不能包含空格",pt_mtu_err:"MTU 范围为 64-16383",
 stp_title:"生成树",stp_h:"RSTP, 802.1w",stp_version:"版本",stp_v_stp:"STP 兼容",
@@ -368,15 +368,15 @@ th_sel_light:"Selenized claro",th_sel_dark:"Selenized oscuro",
 c_port:"Puerto",c_name:"Nombre",c_link:"Enlace",c_apply:"Aplicar",c_cancel:"Cancelar",c_confirm:"Confirmar",
 c_close:"Cerrar",c_refresh:"Actualizar",c_off:"apagado",c_offc:"Apagado",c_down:"caído",c_on:"Encendido",c_auto:"Auto",c_delete:"Eliminar",
 c_type:"Tipo",c_state:"Estado",c_enabled:"Habilitado",c_load:"Cargar",c_disable:"Deshabilitar",c_sfp:"SFP",
-c_full:"dúplex completo",c_half:"semidúplex",c_devices:"dispositivos",c_yes:"sí",c_no:"no",
+c_full:"dúplex completo",c_half:"semidúplex",c_yes:"sí",c_no:"no",
-d_ports:"Puertos",d_ports_h:"pulsa un puerto para ver detalles",d_system:"Sistema",d_traffic:"Tráfico",
+d_system:"Sistema",d_traffic:"Tráfico",
 d_traffic_h:"paquetes/s, en vivo",d_txpps:"TX pps",d_rxpps:"RX pps",d_txbad:"TX erróneos",d_rxbad:"RX erróneos",
 i_host:"Nombre de host",i_ip:"Dirección IP",i_mask:"Máscara de red",i_gw:"Puerta de enlace",i_mac:"MAC",i_fw:"Firmware",
 i_built:"Compilado",i_hw:"Hardware",i_flash:"Flash",i_syslog:"Syslog",
 p_state:"Estado",p_disabled:"deshabilitado",p_up:"activo",p_txgb:"TX correctos / erróneos",p_rxgb:"RX correctos / erróneos",
 p_pkts:"paquetes",p_module:"Módulo",p_temp:"Temperatura",p_vcc:"Vcc",p_txbias:"Polarización TX",p_txpower:"Potencia TX",
 p_rxpower:"Potencia RX",p_txfault:"Fallo TX",p_txdis:"TX deshabilitado",p_rxlos:"Pérdida RX (LOS)",p_adv:"Anunciado",
-pt_title:"Configuración de puerto",pt_conn:"Conectado",pt_speed:"Velocidad",pt_mtu:"MTU",
+pt_title:"Configuración de puerto",pt_conn:"Dispositivos aprendidos",pt_speed:"Velocidad",pt_mtu:"MTU",
 pt_sfp_note:"La velocidad del SFP se ajusta por ranura y no se guarda en la configuración de inicio.",
 pt_name_err:"Nombre de puerto: 1-15 caracteres, sin espacios",pt_mtu_err:"El MTU debe estar entre 64 y 16383",
 stp_title:"Árbol de expansión",stp_h:"RSTP, 802.1w",stp_version:"Versión",stp_v_stp:"STP compatible",
@@ -480,15 +480,15 @@ th_sel_light:"Clair (sélénisé)",th_sel_dark:"Sombre (sélénisé)",
 c_port:"Port",c_name:"Nom",c_link:"Lien",c_apply:"Appliquer",c_cancel:"Annuler",c_confirm:"Confirmer",
 c_close:"Fermer",c_refresh:"Raffraichir",c_off:"arrêt",c_offc:"Arrêt",c_down:"arrêt",c_on:"Marche",c_auto:"Auto",c_delete:"Supprimer",
 c_type:"Type",c_state:"Etat",c_enabled:"Activé",c_load:"Charger",c_disable:"Désactivé",c_sfp:"SFP",
-c_full:"full",c_half:"half",c_devices:"Equipements",c_yes:"oui",c_no:"non",
+c_full:"full",c_half:"half",c_yes:"oui",c_no:"non",
-d_ports:"Ports",d_ports_h:"Cliquez ou survollez pour plus de détails",d_system:"Système",d_traffic:"Trafic",
+d_system:"Système",d_traffic:"Trafic",
 d_traffic_h:"paquets/s (en direct)",d_txpps:"TX pps",d_rxpps:"RX pps",d_txbad:"TX KO",d_rxbad:"RX KO",
 i_host:"Nom d'hote",i_ip:"Adresse IP",i_mask:"Masque réseau",i_gw:"Passerelle",i_mac:"Adresse MAC",i_fw:"Micro logiciel",
 i_built:"Compilé le",i_hw:"Matériel",i_temp:"Température",i_flash:"Taille Flash",i_syslog:"Journal système",
 p_state:"Etat",p_disabled:"Inactif",p_up:"Actif",p_txgb:"TX bon / mauvais",p_rxgb:"RX bon / mauvais",
 p_pkts:"paquets",p_module:"Module",p_temp:"Température",p_vcc:"Vcc",p_txbias:"TX biais",p_txpower:"TX puissance",
 p_rxpower:"RX puissance",p_txfault:"TX erreur",p_txdis:"TX désactivé",p_rxlos:"RX pertes de signaux",p_adv:"Capacités",
-pt_title:"Configuration du port",pt_conn:"Connecté à",pt_speed:"Vitesse",pt_mtu:"MTU",
+pt_title:"Configuration du port",pt_conn:"Appareils appris",pt_speed:"Vitesse",pt_mtu:"MTU",
 pt_sfp_note:"La vitesse SFP est paramétrée pour le port et n'est pas enregistrée dans la configuration de démarrage.",
 pt_name_err:"Nom du port: 1 à 15 caractères, sans espaces",pt_mtu_err:"MTU doit être comrpis entre 64 et 16383",
 stp_title:"Arborescence",stp_h:"RSTP, 802.1w",stp_version:"Protocole",stp_v_stp:"Compatible STP",
@@ -588,7 +588,7 @@ fw_timeout:"Le commutateur n'est plus joignable depuis 150 s: verifiez l'aliment
 },
 de:{
 nav_dash:"Übersicht",nav_ports:"Ports",nav_stp:"Spanning Tree",nav_stats:"Statistik",
-nav_vlan:"VLANs",nav_l2:"MAC-Tabelle",nav_mirror:"Spiegelung",nav_lag:"LAG",nav_eee:"EEE",
+nav_vlan:"VLANs",nav_l2:"MAC-Tabelle",nav_mirror:"Spiegelung",nav_isolate:"Isolation",nav_lag:"LAG",nav_eee:"EEE",
 nav_bw:"Bandbreite",nav_system:"System",nav_fw:"Firmware",
 hdr_dirty:"ungespeicherte Änderungen",hdr_dirty_t:"Laufende Konfiguration weicht von der Startkonfiguration ab",
 hdr_save:"Im Flash speichern",hdr_save_t:"Laufende Konfiguration dauerhaft im Flash speichern",
@@ -597,15 +597,15 @@ th_sel_light:"Selenized Hell",th_sel_dark:"Selenized Dunkel",
 c_port:"Port",c_name:"Name",c_link:"Link",c_apply:"Übernehmen",c_cancel:"Abbrechen",c_confirm:"Bestätigen",
 c_close:"Schliessen",c_refresh:"Aktualisieren",c_off:"aus",c_offc:"Aus",c_down:"getrennt",c_on:"Ein",c_auto:"Auto",c_delete:"Löschen",
 c_type:"Typ",c_state:"Zustand",c_enabled:"Aktiviert",c_load:"Laden",c_disable:"Deaktivieren",c_sfp:"SFP",
-c_full:"voll",c_half:"halb",c_devices:"Geräte",c_yes:"ja",c_no:"nein",
+c_full:"voll",c_half:"halb",c_yes:"ja",c_no:"nein",
-d_ports:"Ports",d_ports_h:"Port anklicken für Details",d_system:"System",d_traffic:"Datenverkehr",
+d_system:"System",d_traffic:"Datenverkehr",
 d_traffic_h:"Pakete/s, live",d_txpps:"TX Pakete/s",d_rxpps:"RX Pakete/s",d_txbad:"TX fehlerhaft",d_rxbad:"RX fehlerhaft",
 i_host:"Hostname",i_ip:"IP-Adresse",i_mask:"Netzmaske",i_gw:"Gateway",i_mac:"MAC",i_fw:"Firmware",
 i_built:"Erstellt",i_hw:"Hardware",i_temp:"Temperatur",i_flash:"Flash",i_syslog:"Syslog",
 p_state:"Zustand",p_disabled:"deaktiviert",p_up:"verbunden",p_txgb:"TX gut / fehlerhaft",p_rxgb:"RX gut / fehlerhaft",
 p_pkts:"Pakete",p_module:"Modul",p_temp:"Temperatur",p_vcc:"Vcc",p_txbias:"TX-Bias",p_txpower:"Sendeleistung",
 p_rxpower:"Empfangsleistung",p_txfault:"TX-Fehler",p_txdis:"TX deaktiviert",p_rxlos:"RX LOS",p_adv:"Angeboten",
-pt_title:"Port-Konfiguration",pt_conn:"Verbunden",pt_speed:"Geschwindigkeit",pt_mtu:"MTU",
+pt_title:"Port-Konfiguration",pt_conn:"Gelernte Geräte",pt_speed:"Geschwindigkeit",pt_mtu:"MTU",
 pt_sfp_note:"Die SFP-Geschwindigkeit wird pro Steckplatz gesetzt und nicht in der Startkonfiguration gespeichert.",
 pt_name_err:"Port-Name: 1-15 Zeichen, keine Leerzeichen",pt_mtu_err:"MTU muss zwischen 64 und 16383 liegen",
 stp_title:"Spanning Tree",stp_h:"RSTP, 802.1w",stp_version:"Version",stp_v_stp:"STP-kompatibel",
@@ -626,6 +626,7 @@ stp_en_q:"Spanning Tree aktivieren?",
 stp_en_d:"Die Ports starten blockiert und brauchen bis zum doppelten Forward Delay, bis sie weiterleiten; Edge-Ports sind sofort wieder aktiv.",
 stp_dis_q:"Spanning Tree deaktivieren?",stp_dis_d:"Alle Ports leiten sofort weiter; der Schutz vor Netzwerkschleifen entfällt.",
 stp_cost_err:"Pfadkosten müssen zwischen 0 und 200000000 liegen",
+nav_lldp:"LLDP",lldp_enabled:"LLDP aktiv",lldp_title:"Dienststatus",lldp_portname:"Name",lldp_enable:"Pakete senden",
 st_title:"Port-Statistik",st_h:"Summen seit dem Start",st_txg:"TX gut",st_txb:"TX fehlerhaft",st_rxg:"RX gut",
 st_rxb:"RX fehlerhaft",st_details:"Details",st_counters:"MIB-Zähler",st_nonzero:"nur ungleich null",
 st_autoref:"automatisch aktualisieren",st_counter:"Zähler",st_value:"Wert",st_fail:"Zähler konnten nicht geladen werden",
@@ -648,8 +649,12 @@ l2_learned:"gelernt",l2_loading:"lädt...",l2_failed:"Laden fehlgeschlagen",l2_e
 l2_del_t:"Eintrag löschen",l2_flush_q:"Alle gelernten MAC-Einträge löschen?",
 m_title:"Port-Spiegelung",m_active:"aktiv",m_monitor:"Monitor-Port",m_mirror:"Spiegeln",m_both:"Beide",
 m_note:"Beide = RX und TX des Ports auf den Monitor-Port spiegeln.",m_none:"Mindestens einen zu spiegelnden Port wählen",
+iso_title:"Port-Isolation",iso_from:"Von Port",iso_to:"Zu Port",iso_all:"Alle erlauben",
+iso_intro:"Ein Paket, das über einen Port hereinkommt, darf den Switch nur über die Ports verlassen, die in seiner Zeile angehakt sind. Die Isolation wirkt vor der Weiterleitung: Ein nicht angehakter Port ist direkt nicht erreichbar, egal was in der MAC-Tabelle steht.",
+iso_legend:"Das Feld des Ports selbst ist immer erlaubt. Eine rote Portnummer markiert einen Port, der nicht ganz offen ist.",
 lag_hash:"Hash:",lag_note:"Eine LAG braucht mindestens ein Mitglied, um in der Startkonfiguration gespeichert zu werden; eine leere Gruppe zu übernehmen löscht sie.",
 lag_clear_q:"LAG {n} auflösen?",lag_clear_d:"Alle Mitglieds-Ports kehren in den Normalbetrieb zurück.",
+lacp_heading:"LACP (802.3ad)",lag_mode:"Modus",lag_static:"Statisch",lacp_neg:"wird ausgehandelt",lacp_agg:"Aggregator",lacp_members:"aktive Mitglieder",lacp_hint:"LACP: Ports auswählen und Übernehmen drücken, um die Aushandlung zu starten",lacp_actor:"Lokal",lacp_partner:"Partner",lacp_rxstate:"Empfangsstatus",lacp_rx:"Empfangene LACPDUs",lacp_psys:"Partner-System",
 e_title:"Energy Efficient Ethernet",e_adv:"Angeboten",e_lp:"Gegenstelle",e_active:"Aktiv",e_enable:"Aktivieren",
 e_note:"Angebotene und von der Gegenstelle unterstützte Stufen je Geschwindigkeit: 100M, 1G, 2.5G. SFP-Ports unterstützen kein EEE.",
 e_idle:"inaktiv",e_na:"k. A.",
@@ -672,7 +677,8 @@ sy_ip_err:"Ungültige IP / Netzmaske / Gateway",sy_host_err:"Hostname: 1-23 druc
 sy_net_q:"Netzwerkeinstellungen übernehmen?",sy_net_d:"Die Management-IP ändert sich auf {ip}: Diese Seite muss dort neu geöffnet werden.",
 sy_ip_changed:"IP geändert, neu verbinden unter http://{ip}/",sy_dhcp_q:"Auf DHCP umstellen?",
 sy_dhcp_d:"Der Switch bezieht seine Adresse per DHCP. Du musst seine neue IP herausfinden, um dich wieder zu verbinden.",
-sy_sysip_err:"Ungültige IP des Syslog-Servers",sy_sysport_err:"Syslog-Port muss zwischen 1 und 65535 liegen",
+sy_sysip_err:"Ungültige IP des Syslog-Servers",sy_dns1:"DNS-Server",sy_dns2:"Zweiter DNS-Server",sy_dns_err:"Ungültige IP des DNS-Servers",sy_dns_dhcp:"von DHCP: {ip}",sy_sysport_err:"Syslog-Port muss zwischen 1 und 65535 liegen",
+sy_time:"Uhrzeit",sy_ntp:"NTP",sy_ntpsrv:"NTP-Server",sy_ntpsrv_p:"Hostname oder IPv4-Adresse",sy_ntpint:"Abfrageintervall [min]",sy_tz:"Zeitzone",sy_dst:"Sommerzeit",sy_dst_eu:"Europa",sy_dst_us:"USA",sy_now:"Lokale Zeit",sy_sync:"Letzte Synchronisation",sy_ntpaddr:"Server-Adresse",sy_nosync:"nicht synchronisiert",sy_waiting:"warte auf den Server",sy_ago:"vor {n} min",sy_ntp_err:"Hostname oder IPv4-Adresse des NTP-Servers eingeben",sy_ntpint_err:"Abfrageintervall muss zwischen 1 und 1440 liegen",sy_time_note:"Der Switch hat keine batteriegepufferte Uhr: Die Zeit geht bei jedem Neustart verloren und wird neu vom NTP-Server bezogen, sobald das Netzwerk bereit ist. Im Flash speichern, damit die Einstellungen erhalten bleiben.",
 sy_pw_len:"Passwort: 1-20 Zeichen",sy_pw_space:"Das Passwort darf keine Leerzeichen enthalten",sy_pw_match:"Die Passwörter stimmen nicht überein",
 sy_pw_q:"Admin-Passwort ändern?",sy_pw_d:"Gilt sofort für neue Anmeldungen. Im Flash speichern, damit es erhalten bleibt.",
 sy_reboot_q:"Switch neu starten?",sy_reboot_d:"Es gibt UNGESPEICHERTE Änderungen, sie gehen verloren. Zuerst im Flash speichern, wenn du sie behalten willst.",
@@ -958,6 +964,7 @@ function pollStatus(){
   });
 }
 var statusPoller=new Poller(pollStatus,2500);
+statusPoller.start();
 function needPorts(fn){
   if(S.n)return fn();
   pollStatus().then(fn).catch(function(){});
@@ -1102,8 +1109,7 @@ function dashStatus(){
   });
 }
 tabHooks.dash={
-  enter:function(){statusPoller.start();pollInfo().catch(function(){})},
+  enter:function(){pollInfo().catch(function(){})},
-  leave:function(){statusPoller.stop()},
   status:dashStatus,
 };
 
@@ -1147,31 +1153,12 @@ function loadMtu(){
     });
   });
 }
-/* One learned MAC is the attached device; several means a switch or AP
- * sits behind the port, so only the count is shown. */
-function portsMacs(){
-  l2Load().then(function(all){
-    var by={};
-    all.forEach(function(e){
-      if(e.pport==="CPU")return;
-      var l=by[e.pport]=by[e.pport]||[];
-      if(l.indexOf(e.mac)<0)l.push(e.mac);
-    });
-    S.ports.forEach(function(p){
-      var el=$("pmac"+(p.portNum-1));
-      if(!el)return;
-      var m=by[p.portNum]||[];
-      el.textContent=!m.length?"-":(m.length===1?m[0]:m.length+" "+t("c_devices"));
-      el.title=m.join("\n");
-    });
-  }).catch(function(){});
-}
-var _macTick=0;
 function portsStatus(){
   buildPorts();
-  if(++_macTick%10===0)portsMacs();
   S.ports.forEach(function(p){
     var i=p.portNum-1,el=$("plink"+i);
+    var mc=$("pmac"+i);
+    if(mc)mc.textContent=parseInt(p.macs,16)&0x1fff;
     if(el)el.innerHTML=linkBadge(p);
     var sel=$("pspd"+i),v=p.isSFP?0:ADVSEL[parseInt(p.adv,2)];
     if(sel&&v&&document.activeElement!==sel)sel.value=v;
@@ -1199,8 +1186,7 @@ function applyPort(i){
   postCmds(cmds).then(loadMtu).catch(function(){});
 }
 tabHooks.ports={
-  enter:function(){statusPoller.start();needPorts(function(){buildPorts();portsMacs()})},
+  enter:function(){needPorts(buildPorts)},
-  leave:function(){statusPoller.stop();l2Gen++},
   status:portsStatus,
 };
 
@@ -1456,8 +1442,7 @@ function statsStatus(){
   });
 }
 tabHooks.stats={
-  enter:function(){statusPoller.start()},
+  leave:function(){if(ctrPoll)ctrPoll.stop()},
-  leave:function(){statusPoller.stop();if(ctrPoll)ctrPoll.stop()},
   status:statsStatus,
 };
 

html/index.html

@@ -55,11 +55,11 @@ a{color:var(--ac);text-decoration:none}
 #navfoot{padding:10px 16px;border-top:1px solid var(--bd);font-size:12px;color:var(--fg2)}
 #wrap{flex:1;min-width:0;display:flex;flex-direction:column}
 #top{
-  display:flex;align-items:center;gap:10px;padding:10px 20px;
+  display:flex;align-items:center;flex-wrap:wrap;gap:10px;padding:8px 20px;
   background:var(--panel);border-bottom:1px solid var(--bd);position:sticky;top:0;z-index:5;
 }
 #burger{display:none;background:none;border:0;cursor:pointer;padding:4px}
-#ttitle{font-size:16px;font-weight:650;flex:1}
+#ttitle{font-size:16px;font-weight:650;min-width:120px}
 #dirty{
   display:none;font-size:12px;font-weight:600;color:var(--warn);
   border:1px solid var(--warn);border-radius:20px;padding:2px 10px;
@@ -112,19 +112,21 @@ label.row span.lb{width:110px;flex:none;color:var(--fg2);font-size:13px}
 }
 .switch input:checked+i{background:var(--ok)}
 .switch input:checked+i:before{transform:translateX(15px)}
-#strip{display:flex;gap:8px;flex-wrap:wrap;padding:4px 0 2px}
+#strip{display:flex;gap:6px;flex:1;min-width:0;overflow-x:auto;scrollbar-width:thin}
+.port:first-child{margin-left:auto}
+.port:last-child{margin-right:auto}
 .port{
-  width:46px;border:2px solid var(--bd);border-radius:7px;padding:5px 0 3px;
+  width:40px;border:2px solid var(--bd);border-radius:7px;padding:3px 0 2px;
   text-align:center;cursor:pointer;background:var(--panel2);position:relative;
 }
-.port.sfp{width:56px}
+.port.sfp{width:50px}
-.port .pn{font-weight:650;font-size:13px}
+.port .pn{font-weight:650;font-size:12px}
-.port .ps{font-size:10px;color:var(--fg2);display:block;line-height:1.2}
+.port .ps{font-size:9px;color:var(--fg2);display:block;line-height:1.2}
 .port .jack{
-  display:block;width:18px;height:12px;margin:3px auto 2px;border-radius:2px;
+  display:block;width:16px;height:10px;margin:2px auto 1px;border-radius:2px;
-  border:2px solid var(--fg2);border-top-width:5px;opacity:.55;
+  border:2px solid var(--fg2);border-top-width:4px;opacity:.55;
 }
-.port.sfp .jack{width:28px;height:10px;border-top-width:3px}
+.port.sfp .jack{width:24px;height:9px;border-top-width:3px}
 .port.up{border-color:var(--pc);background:color-mix(in srgb,var(--pc) 10%,var(--panel2))}
 .port.up .jack{border-color:var(--pc);opacity:1}
 .port.up .ps{color:var(--pc);font-weight:600}
@@ -183,6 +185,10 @@ button.danger{background:var(--bad);color:#fff;border-color:transparent}
   #ttitle{font-size:14px;overflow:hidden;text-overflow:ellipsis;white-space:nowrap}
   #dirty{padding:2px 7px}
 }
+@media (max-width:720px){
+  #ttitle{flex:1}
+  #strip{order:3;flex-basis:100%}
+}
 </style>
 <script>
 (function(){
@@ -215,15 +221,13 @@ button.danger{background:var(--bad);color:#fff;border-color:transparent}
       <svg width="20" height="20" viewBox="0 0 24 24" fill="none" stroke="var(--fg)" stroke-width="2"><path d="M4 6h16M4 12h16M4 18h16"/></svg>
     </button>
     <span id="ttitle"></span>
+    <div id="strip"></div>
     <span id="dirty" data-i18n="hdr_dirty" data-i18n-t="hdr_dirty_t">unsaved changes</span>
     <button class="ctl pri" id="saveBtn" data-i18n="hdr_save" data-i18n-t="hdr_save_t">Save to flash</button>
   </header>
 
   <main>
     <section class="tab act" id="tab-dash">
-      <div class="card"><h2><span data-i18n="d_ports">Ports</span> <span class="hint" data-i18n="d_ports_h">click a port for details</span></h2>
-        <div id="strip"></div>
-      </div>
       <div class="grid2">
         <div class="card"><h2 data-i18n="d_system">System</h2><table class="t" id="sysinfo"></table></div>
         <div class="card"><h2><span data-i18n="d_traffic">Traffic</span> <span class="hint" data-i18n="d_traffic_h">packets/s, live</span></h2>
@@ -237,7 +241,7 @@ button.danger{background:var(--bad);color:#fff;border-color:transparent}
     <section class="tab" id="tab-ports">
       <div class="card"><h2 data-i18n="pt_title">Port configuration</h2>
         <div class="scrollx"><table class="t" id="ptable">
-          <thead><tr><th data-i18n="c_port">Port</th><th data-i18n="c_name">Name</th><th data-i18n="c_link">Link</th><th data-i18n="pt_conn">Connected</th><th data-i18n="pt_speed">Speed</th><th data-i18n="c_enabled">Enabled</th><th data-i18n="pt_mtu">MTU</th><th></th></tr></thead>
+          <thead><tr><th data-i18n="c_port">Port</th><th data-i18n="c_name">Name</th><th data-i18n="c_link">Link</th><th data-i18n="pt_conn">Devices learned</th><th data-i18n="pt_speed">Speed</th><th data-i18n="c_enabled">Enabled</th><th data-i18n="pt_mtu">MTU</th><th></th></tr></thead>
           <tbody></tbody></table></div>
         <p class="small mut" style="margin-top:8px" data-i18n="pt_sfp_note">SFP speed is set per slot and is not saved in the startup config.</p>
       </div>

httpd/page_impl.c

@@ -1111,6 +1111,9 @@ void send_status(void)
 		slen += strtox(outbuf + slen, "\",\"rxB\":\"0x");
 		STAT_GET(STAT_COUNTER_ERR_PKTS, i);
 		reg_to_html(RTL837X_STAT_V_HIGH);	// 32bit RX packet errors
+
+		slen += strtox(outbuf + slen, "\",\"macs\":\"0x");
+		reg_to_html(RTL837X_L2_LRN_PORT_CONSTRT_CNT + (i << 2));
 		slen += strtox(outbuf + slen, "\"}");
 		if (i < machine.max_port)
 			char_to_html(',');

machine/GT_ST024M.c

@@ -0,0 +1 @@
+PCB_SWTG024AS_A_2_0_1.c

machine/GT_ST024M.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_GT_ST024M_H_
+#define _MACHINE_GT_ST024M_H_
+
+#define MACHINE_MODEL "GoodTop GT-ST024M"
+
+#endif

machine/SWGT024_V2_0_MANAGED.c

@@ -38,4 +38,5 @@ __code const struct machine machine = {
 			0,
 		},
 	},
+	.mac_flash_offset = 0x1FC000,
 };

rtl837x_cabletest.c

@@ -0,0 +1,216 @@
+#include <stdint.h>
+#include <stdbool.h>
+#include "rtl837x_common.h"
+#include "rtl837x_sfr.h"
+#include "rtl837x_cabletest.h"
+#include "rtl837x_phy.h"
+#include "phy.h"
+#include "machine.h"
+
+#pragma codeseg BANK3
+#pragma constseg BANK3
+
+#define RTCT_CTRL		0xa422
+#define RTCT_CTRL_START		0x00f1
+#define RTCT_CTRL_DONE		0x8000
+#define RTCT_SRAM_ADDR		0xa436
+#define RTCT_SRAM_DATA		0xa438
+#define RTCT_SRAM_STATUS	0x8026
+#define RTCT_SRAM_LEN		0x8028
+
+#define RTCT_ST_BUSY		0x01
+#define RTCT_ST_MISMATCH	0x06
+#define RTCT_ST_OPEN		0x08
+#define RTCT_ST_SHORT		0x10
+#define RTCT_ST_OK		0x20
+#define RTCT_ST_DONE		0x40
+#define RTCT_ST_CROSS_SHORT	0x80
+
+#define RTCT_LEN_ZERO		150
+#define RTCT_LEN_PER_50CM	43
+
+#define PHY_POWER		0xa610
+#define PHY_POWER_OFF		0x0800
+
+#define BMCR_PDOWN_1G_FULL	0x0940
+#define BMCR_1G_FULL		0x0140
+#define BMCR_ANRESTART		0x0200
+
+#define CT_IDLE			0
+#define CT_SILENCE		1
+#define CT_RUN			2
+#define CT_POLL_TICKS		(SYS_TICK_HZ / 20)
+#define CT_POLLS		100
+
+extern volatile __xdata uint32_t ticks;
+extern __code const struct machine machine;
+extern __xdata struct machine_runtime machine_detected;
+
+__xdata uint8_t ct_state = CT_IDLE;
+__xdata uint8_t ct_port;
+__xdata uint8_t ct_last;
+__xdata uint8_t ct_polls;
+__xdata uint8_t ct_valid;
+__xdata uint8_t ct_have = 0;
+__xdata uint8_t ct_pair;
+__xdata uint8_t ct_flags;
+__xdata uint16_t ct_bmcr;
+__xdata uint8_t ct_result[4];
+__xdata uint16_t ct_len[4];
+
+void rtl_phy_cable_test_start(uint8_t port) __banked
+{
+	phy_write(port, PHY_MMD31, PHY_MMD31_FEDCR, BMCR_1G_FULL);
+	phy_write(port, PHY_MMD31, RTCT_CTRL, RTCT_CTRL_START);
+}
+
+bool rtl_phy_cable_test_get_status(uint8_t port) __banked
+{
+	phy_read(port, PHY_MMD31, RTCT_CTRL);
+	if (!(SFR_DATA_U16 & RTCT_CTRL_DONE))
+		return false;
+
+	for (ct_pair = 0; ct_pair < 4; ct_pair++) {
+		// The flags are the low byte of the word, not the high one.
+		phy_write(port, PHY_MMD31, RTCT_SRAM_ADDR, RTCT_SRAM_STATUS + (ct_pair << 2));
+		phy_read(port, PHY_MMD31, RTCT_SRAM_DATA);
+		ct_flags = SFR_DATA_U16;
+		if (!(ct_flags & RTCT_ST_DONE))
+			return false;
+		if (ct_flags & RTCT_ST_OK)
+			ct_result[ct_pair] = CABLE_RESULT_OK;
+		else if (ct_flags & RTCT_ST_OPEN)
+			ct_result[ct_pair] = CABLE_RESULT_OPEN;
+		else if (ct_flags & RTCT_ST_SHORT)
+			ct_result[ct_pair] = CABLE_RESULT_SAME_SHORT;
+		else if (ct_flags & RTCT_ST_BUSY)
+			ct_result[ct_pair] = CABLE_RESULT_UNSPEC;
+		else if (ct_flags & RTCT_ST_CROSS_SHORT)
+			ct_result[ct_pair] = CABLE_RESULT_CROSS_SHORT;
+		else if (ct_flags & RTCT_ST_MISMATCH)
+			ct_result[ct_pair] = CABLE_RESULT_MISMATCH;
+		else
+			ct_result[ct_pair] = CABLE_RESULT_UNSPEC;
+
+		phy_write(port, PHY_MMD31, RTCT_SRAM_ADDR, RTCT_SRAM_LEN + (ct_pair << 2));
+		phy_read(port, PHY_MMD31, RTCT_SRAM_DATA);
+		ct_len[ct_pair] = SFR_DATA_U16;
+		ct_len[ct_pair] = ct_len[ct_pair] > RTCT_LEN_ZERO ? ct_len[ct_pair] - RTCT_LEN_ZERO : 0;
+		ct_len[ct_pair] = ct_len[ct_pair] * 5 / RTCT_LEN_PER_50CM;
+	}
+	return true;
+}
+
+static void cabletest_print(void)
+{
+	print_string("Cable test port ");
+	print_phys_port(ct_port);
+	if (!ct_valid) {
+		print_string(": timed out\n");
+		return;
+	}
+	write_char('\n');
+	for (ct_pair = 0; ct_pair < 4; ct_pair++) {
+		print_string("Pair ");
+		write_char('A' + ct_pair);
+		switch (ct_result[ct_pair]) {
+		case CABLE_RESULT_OK:
+			print_string(": ok\n");
+			continue;
+		case CABLE_RESULT_OPEN:
+			print_string(": open at ");
+			break;
+		case CABLE_RESULT_SAME_SHORT:
+			print_string(": short at ");
+			break;
+		case CABLE_RESULT_CROSS_SHORT:
+			print_string(": short to another pair at ");
+			break;
+		case CABLE_RESULT_MISMATCH:
+			print_string(": impedance mismatch at ");
+			break;
+		default:
+			print_string(": unknown\n");
+			continue;
+		}
+		itoa_short(ct_len[ct_pair] / 10);
+		write_char('.');
+		write_char('0' + ct_len[ct_pair] % 10);
+		print_string(" m\n");
+	}
+}
+
+void cabletest_run(void) __banked
+{
+	if (ct_state) {
+		print_string("Cable test running on port ");
+		print_phys_port(ct_port);
+		write_char('\n');
+		return;
+	}
+	if (!machine_detected.isRTL8373 && (phy_settings.port < 4 || phy_settings.port > 7)) {
+		print_string("No cable test on this PHY\n");
+		return;
+	}
+
+	// A test started on a port that is off never ends and blocks the PHY until reset.
+	phy_read(phy_settings.port, PHY_MMD31, PHY_POWER);
+	if (SFR_DATA_U16 & PHY_POWER_OFF) {
+		print_string("Port is off\n");
+		return;
+	}
+
+	ct_port = phy_settings.port;
+	phy_read(ct_port, PHY_MMD31, PHY_MMD31_FEDCR);
+	ct_bmcr = SFR_DATA_U16;
+
+	// Forcing the speed leaves the link up; only a power-down silences the partner.
+	phy_write(ct_port, PHY_MMD31, PHY_MMD31_FEDCR, BMCR_PDOWN_1G_FULL);
+	ct_last = ticks;
+	ct_have = 0;
+	ct_state = CT_SILENCE;
+	print_string("Cable test started\n");
+}
+
+void cabletest_show(void) __banked
+{
+	if (ct_state)
+		print_string("Cable test running\n");
+	else if (ct_port != phy_settings.port || !ct_have)
+		print_string("No cable test result\n");
+	else
+		cabletest_print();
+}
+
+void cabletest_tick(void) __banked
+{
+	if (ct_state == CT_SILENCE) {
+		if (!TICKS_DUE(ct_last, SYS_TICK_HZ))
+			return;
+		phy_read(ct_port, PHY_MMD31, PHY_POWER);
+		if (SFR_DATA_U16 & PHY_POWER_OFF) {
+			phy_write(ct_port, PHY_MMD31, PHY_MMD31_FEDCR, ct_bmcr);
+			ct_state = CT_IDLE;
+			print_string("Cable test aborted, port is off\n");
+			return;
+		}
+		rtl_phy_cable_test_start(ct_port);
+		ct_polls = CT_POLLS;
+		ct_last = ticks;
+		ct_state = CT_RUN;
+		return;
+	}
+	if (ct_state != CT_RUN || !TICKS_DUE(ct_last, CT_POLL_TICKS))
+		return;
+	ct_last = ticks;
+
+	ct_valid = rtl_phy_cable_test_get_status(ct_port);
+	if (!ct_valid && --ct_polls)
+		return;
+
+	phy_write(ct_port, PHY_MMD31, RTCT_CTRL, 0);
+	phy_write(ct_port, PHY_MMD31, PHY_MMD31_FEDCR, ct_bmcr | BMCR_ANRESTART);
+	ct_have = 1;
+	ct_state = CT_IDLE;
+	cabletest_print();
+}

rtl837x_cabletest.h

@@ -0,0 +1,21 @@
+#ifndef _RTL837X_CABLETEST_H_
+#define _RTL837X_CABLETEST_H_
+
+#include <stdint.h>
+#include <stdbool.h>
+
+#define CABLE_RESULT_UNSPEC		0
+#define CABLE_RESULT_OK			1
+#define CABLE_RESULT_OPEN		2
+#define CABLE_RESULT_SAME_SHORT		3
+#define CABLE_RESULT_CROSS_SHORT	4
+#define CABLE_RESULT_MISMATCH		5
+
+void rtl_phy_cable_test_start(uint8_t port) __banked;
+bool rtl_phy_cable_test_get_status(uint8_t port) __banked;
+
+void cabletest_run(void) __banked;
+void cabletest_show(void) __banked;
+void cabletest_tick(void) __banked;
+
+#endif

rtl837x_port.c

@@ -510,7 +510,7 @@ void port_media_show(uint8_t port) __banked
 
 void port_stats_print(void) __banked
 {
-	print_string("\nPort\tState\tLink\tTxGood\t\tTxBad\t\tRxGood\t\tRxBad\n");
+	print_string("\nPort\tState\tLink\tTxGood\t\tTxBad\t\tRxGood\t\tRxBad\t\tMACs\n");
 	for (uint8_t i = machine.min_port; i <= machine.max_port; i++) {
 		print_phys_port(i); write_char('\t');
 
@@ -584,6 +584,9 @@ void port_stats_print(void) __banked
 
 		STAT_GET(STAT_COUNTER_ERR_PKTS, i);
 		print_reg(RTL837X_STAT_V_HIGH); write_char('\t');
+
+		reg_read(RTL837X_L2_LRN_PORT_CONSTRT_CNT + (i << 2));
+		itoa_short(SFR_DATA_U16 & L2_LRN_PORT_CNT_MASK);
 		print_string("\n");
 	}
 }

rtl837x_regs.h

@@ -214,6 +214,8 @@
 #define RTL837x_L2_TBL_FLUSH_CNF	0x53dc
 #define RTL837X_L2_LRN_PORT_CONSTRAINT	0x5384
 #define RTL837X_L2_LRN_PORT_CONSTRT_ACT	0x4f80
+#define RTL837X_L2_LRN_PORT_CONSTRT_CNT	0x53ac
+#define L2_LRN_PORT_CNT_MASK		0x1fff
 #define	RTL8373_REG_MAC_L2_PORT_MAX_LEN	0x1250
 
 /*

rtlplayground.c

@@ -19,6 +19,7 @@
 #include "rtl837x_bandwidth.h"
 #include "rtl837x_init.h"
 #include "rtl837x_lldp.h"
+#include "rtl837x_cabletest.h"
 #include "dhcp.h"
 #include "cmd_parser.h"
 #include "cmd_editor.h"
@@ -1301,6 +1302,7 @@ static void handle_tick(void)
 	health_phase(HEALTH_PH_STP);
 	lldp_tick();
 	health_phase(HEALTH_LLDP);
+	cabletest_tick();
 }
 
 

test/test_page_json.c

@@ -185,6 +185,23 @@ static void t_l2_page(void)
 	CHECK(balanced(), "every page is valid JSON");
 }
 
+static void t_status_macs(void)
+{
+	const char *p1, *end, *mac;
+
+	printf("[test] /status.json reports the MAC addresses learned on each port\n");
+	hw_reset(); out_reset();
+	hw_reg_set(RTL837X_L2_LRN_PORT_CONSTRT_CNT + (1 << 2), 0x21);
+	send_status();
+	p1 = strstr(body(), "\"logPort\":1,");
+	end = p1 ? strchr(p1, '}') : NULL;
+	mac = p1 ? strstr(p1, "\"macs\":\"0x21\"") : NULL;
+	CHECK(mac && mac < end, "port 1 shows its learned count");
+	CHECK(has("\"macs\":\"0x0\""), "a port without learned addresses shows 0");
+	CHECK(slen <= TCP_OUTBUF_SIZE, "fits the buffer");
+	CHECK(balanced(), "valid JSON");
+}
+
 static void t_status_counters(void)
 {
 	printf("[test] /status.json prints 64-bit packet counters in full\n");
@@ -211,6 +228,7 @@ int main(void)
 	t_l2();
 	t_l2_page();
 	t_status_counters();
+	t_status_macs();
 	printf("\n%d checks, %d failed\n", tests_run, tests_failed);
 	return tests_failed ? 1 : 0;
 }

test/test_startup_crlf.py

@@ -0,0 +1,52 @@
+#!/usr/bin/env python3
+"""Compile the current firmware execute_config() with mocked flash/tokenizer edges."""
+import pathlib, subprocess
+root=pathlib.Path(__file__).resolve().parent.parent
+src=(root/'cmd_parser.c').read_text()
+start=src.index('void execute_config(void) __banked')
+end=src.index('// Execute multiple commands',start)
+body=src[start:end]
+out=root/'test/build';out.mkdir(exist_ok=True)
+harness=r"""
+#include <stdint.h>
+#include <stdio.h>
+#include <string.h>
+#include <assert.h>
+#define __xdata
+#define __banked
+#define CONFIG_START 0
+#define CONFIG_LEN 1024
+#define FLASH_READ_BURST_SIZE 256
+#define CMD_BUF_SIZE 64
+#define ERR_OK 0
+#define NUL 0
+#define PASSWORD "test-default"
+uint8_t flash_buf[256],cmd_buffer[64],save_cmd,err_status;
+char passwd[32],image[1024],seen[16][64];int count;
+struct {uint32_t addr;uint16_t len;} flash_region;
+void strtox(char*d,const char*s){strcpy(d,s);}
+void flash_read_bulk(uint8_t*d){memcpy(d,image+flash_region.addr,256);}
+void print_string(const char*s){(void)s;}
+void print_string_x(uint8_t*s){(void)s;}
+void write_char(char c){(void)c;}
+void clear_command_history(void){}
+void cmd_tokenize(void){err_status=cmd_buffer[0]=='#'?1:0;}
+void cmd_parser(void){assert(count<16);strcpy(seen[count++],(char*)cmd_buffer);}
+"""
+tests=r"""
+void run(const char*s){memset(image,0,sizeof image);strncpy(image,s,sizeof image-1);count=0;execute_config();assert(save_cmd==1);}
+int main(void){
+run("one\ntwo\n");assert(count==2&&!strcmp(seen[1],"two"));
+run("one\rtwo\r");assert(count==2&&!strcmp(seen[0],"one"));
+run("one\r\ntwo\r\n");assert(count==2&&!strcmp(seen[1],"two"));
+run("\r\n# ignored\r\none\r\n\r\ntwo");assert(count==2&&!strcmp(seen[0],"one"));
+run("one\0ignored");assert(count==1&&!strcmp(seen[0],"one"));
+char longline[300];memset(longline,'x',sizeof longline);strcpy(longline+280,"\r\nok\r\n");run(longline);assert(count==1&&!strcmp(seen[0],"ok"));
+/* CR at the end of a flash burst, LF at the start of the next. */
+char boundary[300];memset(boundary,'\n',255);strcpy(boundary+255,"\r\nok\r\n");run(boundary);assert(count==1&&!strcmp(seen[0],"ok"));
+puts("startup CR/LF/CRLF, comments, NUL, overlong and burst-boundary cases passed");return 0;
+}
+"""
+(out/'startup_crlf.c').write_text(harness+body+tests)
+subprocess.run(['gcc','-std=gnu11','-Wall','-Wextra','-Werror','-g','-fsanitize=address,undefined','-fno-omit-frame-pointer','-no-pie',str(out/'startup_crlf.c'),'-o',str(out/'test_startup_crlf')],check=True)
+subprocess.run([str(out/'test_startup_crlf')],check=True)

tools/httpd_sim.c

@@ -56,6 +56,7 @@ time_t last_session_use;
 
 uint64_t txG[PORTS], txB[PORTS], rxG[PORTS], rxB[PORTS];
 char txG_buff[20], txB_buff[20], rxG_buff[20], rxB_buff[20], counter_buf[20], counter_name[20];
+char macs_buff[8];
 char sfp_temp[8], sfp_vcc[8], sfp_txbias[8], sfp_txpower[8], sfp_rxpower[8], sfp_laser[8], sfp_options[6];
 char num_buff[20];
 char l2_idx_buff[20];
@@ -180,6 +181,12 @@ void send_status(int s)
 		json_object_object_add(v, "txB", json_object_new_string(txB_buff));
 		json_object_object_add(v, "rxG", json_object_new_string(rxG_buff));
 		json_object_object_add(v, "rxB", json_object_new_string(rxB_buff));
+		uint16_t macs = 0;
+		for (int e = 0; e < L2_ENTRY_NUM; e++)
+			if (l2_entries[e].port == physToLogPort[i-1] && l2_entries[e].type != 's')
+				macs++;
+		sprintf(macs_buff, "0x%04x", macs);
+		json_object_object_add(v, "macs", json_object_new_string(macs_buff));
 		if (i >= PORTS - NSFP) {
 			uint16_t temp = 0x28fb + rand() / (RAND_MAX / 100);
 			uint16_t vcc = 0x7eda + rand() / (RAND_MAX / 100);