The LACP test now compiles with the shared harness flags and
sdcc_shim.h against the firmware headers, so the copies under
test/lacp/shim are gone. test_port_tables already covers the trunk hash
seed that test/port_hash checked against its own register copies.
lacp_in() declares its locals at the top, which the stricter host build
needs.
Dynamic link aggregation on top of the static LAGG, for RTL8372/8373:
receive, selection and mux state machines (coupled mux, one aggregator
per group), with "lacp show" to look inside. Each of the four trunk
groups runs its own aggregator on the candidate ports assigned with
"lag <n> lacp <ports>"; the engine starts with the first such group and
stops with the last.
LACPDUs reach the CPU through the reserved-multicast trap, so delivery
needs no L2 entry and nothing written per VLAN or per PVID. The trap
acts on the address before the VLAN lookup and before the ingress
filters, so a LACPDU also arrives on a port that admits tagged frames
only and on a port STP holds in blocking, neither of which a forwarded
one reaches. A trapped frame carries no VLAN tag,
so lacp_in() takes the offset of the PDU body from TRAP_RX_BODY(). The
action is set with trap_rma_set(), which leaves the flags sharing that
register alone, and "lacp off" puts the slow-protocols drop default
back. doc/lacp.md and doc/link_aggregation.md record what was measured,
including why the trap looked like a dead end at first.
The web UI gets a Static/LACP mode per group on the LAG page with live
status, and the startup-config validator knows the per-group syntax. A
host-side sandbox for the state machines runs in the test harness
together with the LAG hash check. It drives both forms of an incoming
LACPDU, so the body offset of a trapped one is covered as well.
The L2 table page iterated with the "next unicast" read method, so
static multicast entries such as an IGMP group were invisible. It now
iterates with "next address", skips L3 entries (their layout carries IP
addresses where a MAC is expected), and reports the lowest member of a
multicast entry's port mask, so such an entry shows up as a static
entry on that port.
A port taken out of LACP forgets its partner, so "lacp show" after
"lacp off" no longer reports one. Applying the same candidate set to a
group again, as the LAG page does on every Apply, leaves the trunk
alone instead of tearing it down for a second or two. lacp_in() checks
the frame length and ethertype before reading a LACPDU, so a runt or a
foreign frame on the slow-protocols address cannot leave stale buffer
bytes as a partner. The sandbox covers these three in T20-T22. On the
LAG page, LACP mode with no ports checked sends "lag N lacp off", and
the startup-config validator wants at least one port after "lacp".
stp_timers() ran every fourth pass of the main loop and stp_clock counted
passes, which only measures time while a pass is one tick long. It never
quite was: a pass is as long as the packets it handles, and #482 now takes
up to four of them, so under an IPv4 stream a pass is about 16 ms and STP
time runs at a third of its rate, with hellos 6 s apart and a root aged out
after a minute. Since #483 the loop also stops sleeping while packets wait,
so under a flood of cheap frames passes come faster than ticks and STP time
runs fast instead, shortening the forward delay in exactly the situation a
loop produces. uip_periodic() had the same problem from the other side: it
ran once per pass, so the retransmit timer sped up with the loop.
Both now go by the tick counter the timer interrupt keeps. The STP block
catches up on ticks a long pass missed, at most eight steps at a time, and
handle_tx() runs its periodics once per tick at most. One byte of xdata
more, 48 bytes of code.
A host test drives the gate with one pass every 5 ms, every 16 ms and
every 0.6 ms for ten seconds each; the STP clock lands on 500 steps in
all three, where counting passes gave 156 and 4166. A pass of 1.3 s loses
time rather than firing 65 steps at once, and the arithmetic survives the
tick counter wrapping.
gcc flags the else whose only statement is dbg_string(), because that macro
expands to nothing unless DEBUG is on, leaving the branch with an empty body.
The line is older than this branch; the bench is simply the first thing that
compiles httpd.c with a host compiler and -Wall -Wextra.
Turn warnings into errors in the test Makefile too, so the next one is caught
where it appears instead of scrolling past. It is the only warning the four
test binaries produce, so nothing else has to change.
Drives the unmodified httpd.c and uip.c through a handshake and a GET
from a client that moves its receive window, and compares the bytes that
reach the wire with the file they are meant to carry. The served file
holds a position-dependent pattern, so a repeat or a gap is reported at
its offset rather than as content that differs somewhere.
The first scenario holds the window still and must pass: it is the check
that the bench itself is sound, before the two moving-window scenarios
are believed.
page_impl.c and rtl837x_port.c are linked together over the simulated
engine, so /vlan.json, /vlanlist and /l2.json are checked against what
vlan_create, pvid and the L2 table hold, through the same bytes the switch
would. The L2 walk is driven the way the web page drives it, page after
page until an index repeats, which is also where the repeat of the first
entry is pinned down as the wrap marker the page relies on. The counter
test fails on the code before the previous commit.
The switch is reached through four register functions and the SFR_DATA
registers, so a flat register file behind them is enough to run the table
code on the host. A few addresses are live: writing TBL_CTRL with EXECUTE
performs the VLAN or L2 operation at once and clears the bit, STAT_GET
fetches a counter, L2_TBL_FLUSH_CTRL drops entries. Nothing ever reports
busy, so a polling loop runs once and the tests say nothing about what
happens when hardware stalls; that question was settled elsewhere.
The header states the VLAN and L2 entry layouts on its own, so a test can
hold what rtl837x_port.c writes against a second reading of the same bits
rather than against itself. The first suite does that for the VLAN entry,
the PVID register two ports share, the static multicast and management
entries, the per-port flush and the trunk registers. Two stub headers stand
in for the ones a firmware build generates, so the harness needs no SDCC
build first.
Building the firmware headers on the host showed two warnings from
machine.h: `typedef struct machine { ... };` and the same for
machine_runtime declare no alias, so the keyword only draws "useless
storage class specifier in empty declaration". Every user says
`struct machine`, so drop the keyword.
-Wno-builtin-declaration-mismatch is a gcc switch and clang reports it
as an unknown option on every build; add it only when the compiler is
not clang.
Compile selected firmware translation units unmodified under host gcc with
AddressSanitizer and UBSan, force-including a shim header that erases the
SDCC 8051 keywords, and link them against a mocked serial ring and console.
A first suite covers the CLI line editor: line entry, backspace editing,
and both long-input overflow cases (length cap and ring-pointer stall).
The only firmware-source change is one #ifndef RTLP_HOST_TEST block in
rtl837x_common.h grouping the libc-named prototypes (sleep/memcpy/memset/
strlen/strcpy/strcmp) so host builds take them from the C library instead;
on-target builds are unaffected.
Run with: make -C test
avicarmeli
João Silva
d00f
bloqaudio