send_config() streams a configuration larger than the TCP output buffer
through the cont_addr/cont_len continuation, but set cont_addr to the
offset within the config instead of a flash address, so the tail was read
from code space. The file server sets cont_addr absolute; do the same by
adding CONFIG_START.
The bug was unreachable while CONFIG_UPLOAD_BUF capped uploads below
TCP_OUTBUF_SIZE, but a stored config near the full sector exposes it.
The two flags added with the JSON fix sit in data, where internal RAM is
full enough that this branch stopped linking for some toolchains. __bit
puts them in the bit area instead and hands three bytes back to the
stack: SSEG goes from 131 to 134 on SWTGW218AS.
Patch by vDorst on the pull request.
The MAC table listing wrote its separator once per iteration rather than
once per object. An entry the table engine reports as invalid produces no
object, so it contributed a bare comma, and two in a row give ",," which
JSON.parse rejects. The whole table then fails to load, not just the row
that was missing. The separator now goes before each object and the
closing bracket after the loop, which is the shape send_vlanlist already
uses further down the file.
The next index for an invalid entry was computed as h | low + 1, and the
addition binds tighter than the or. That agrees with (h | low) + 1 except
when the low byte reads 0xff and bit 8 of the index is already set, eight
of the 4096 combinations. There the result is the start of the current
block of 256 rather than the start of the next one, so the walk repeats a
block it has already covered. Reading the index once after the branch
rather than once in each arm removes the second copy of that expression
along with the bug.
The VLAN now comes first in each object. It is taken from the same
L2_DATA_OUT_B read that decides whether the entry is valid, which saves
reading that register a second time. The page addresses the fields by
name, so the order they arrive in does not matter to it.
A bound check on the output buffer goes in for consistency with
send_vlanlist. Thirty entries of at most 74 bytes plus the brackets fit in
the 2500 byte buffer with 179 to spare, so nothing changes today, but the
margin was nowhere stated and L2_MAX_TRANSFER is a tunable.
5 bytes of BANK1, nothing in BANK2, xdata or internal RAM. Built for SWTGW218AS
and KP_9000_6XHML_X2 on sdcc 4.5.0.
The member mask of an aggregation group is decoded by hand in two places,
the lag command and the JSON behind the aggregation page, and every branch
that touches trunks adds another copy.
port_lag_members_get() sits next to port_lag_members_set() and both readers
call it. It answers from the hardware, so it covers a group configured with
lag and one a protocol brought up, without either having to say so.
It reads through reg_read() rather than reg_read_m(), so sfr_data is left
alone. Neither caller looked at it afterwards; both read the hash register
next.
Review feedback on #306. The value used to ride in /information.json and
the picker fetched /vlanlist separately, so the page needed both requests
to mean anything. /vlanlist now answers {"mgmt":N,"vlan":[...]} and the
picker reads both from the one response. Both consumers in vlan.js were
taught the new shape, and /information.json no longer carries mgmt_vlan.
The truncation guard now reserves 141 bytes instead of 139: the closing
grew to two bytes with the wrapping object, and the comma in front of a
non-first entry was never counted, so the worst case could land one byte
past outbuf even before this change. char_to_html() does not check.
The comments added on this branch are gone as well, style.css and
system.js both, since these files are served byte for byte.
page_impl.rel stays at DSEG 5, OSEG 0, BSEG 3 and the image reports the
same 10183 bytes of XDATA before and after.
`vlan <id> mgmt` existed on the CLI, but nothing reported which VLAN
currently carries management, so the setting was invisible from the web UI -
the only way to find out was to read the startup config.
Report it in information.json and offer it where the other switch-wide
addressing settings live, between Gateway and Language, as a picker filled
from the configured VLANs. When management is untagged there is no VLAN to
select, so that state shows as a disabled entry rather than inventing an id
the switch would reject.
Confirm before applying, and say what will happen rather than echoing the
action back: the switch starts tagging its own frames, and if the port you
came in on does not carry that VLAN the page becomes unreachable and the way
back is the console. Cancelling puts the picker back where it was.
Add a device hostname settable from the CLI (`hostname <text>`) and the
System Settings page. The value is sanitized on ingest to JSON-safe
printable ASCII (<=23 chars), stored in a shared __xdata buffer, seeded
to "RTLPlayground" at boot, persisted through the startup-config, and
reported in /information.json. It lives in the common header so other
modules can advertise it (LLDP uses it as the System Name TLV).
Real root cause of the "web login fails from a browser but works from curl":
the uIP httpd is built with UIP_CONF_MAX_CONNECTIONS = 1 and uses global
response state (outbuf/slen/session), i.e. it serves exactly one TCP connection
at a time and closes it after each response - but never advertises that via
the Connection header. A browser's HTTP/1.1 client therefore assumes the
connection may be persistent and can park it in its keep-alive pool for reuse;
a later request sent on that pooled connection hits one the server has already
closed, and a POST (unlike a GET) is never retried by the browser, so it can
be silently lost this way.
This adds "Connection: close" to every response so the browser does not pool
and reuse a connection the server is about to drop. On its own this did not
fully explain the reported login failures - the actual authentication bug is
fixed in the next commit (the Cookie header parsed at a fixed offset) - but it
is correct behaviour for a server that only ever handles one connection, and
removes one source of dropped requests.
On a QSFPTEK QT-SFP+-T (RTL8261C) 10GBase-T module, the diag type field
(92) comes back as 0x00, but there's actually some statistics available
like temperature. Other metrics may be hard-coded values.
Add a basic struct that allows matching on vendor and/or model, using a
bitfield to allow multiple quirks for a given SFP module. Only
SFP_QUIRK_DDM is implemented.
For modules matching SFP_QUIRK_DDM, attempt an I2C read of the MSB of
module voltage during probe if DDM is "unsupported" - if it's not 0xff,
override the reported options so we can pull the diagnostic data.
To allow simpler comparisons, convert the ASCII fields (vendor,
model, serial) from space-padded to standard NULL-terminated strings.
strcmp() is moved from httpd.c to rtlplayground.c alongside other string
functions and shared between them.
The __reentrant keyword is used for the new functions to avoid using up
additional OSEG space. This allocates the variables on the stack, which
is OK for this particular code path.
The JSON assembly in send_status() is slightly modified to treat the
sfp_module_* data as standard NULL-terminated strings, and a repeated
subtraction was moved into a uint8_t to declutter the code.
- itoa16_html: add comment that the function is sufficient for VLAN
IDs (<=4094); generalization not needed.
- send_vlanlist: replace post-write bounds check with a pre-write
guard using worst-case entry size (138 bytes + 1 for closing
bracket). Old comment claimed ~45 bytes per entry, which only
held for short names. With a 117-char name (the actual bound from
CMD_BUF_SIZE) entries can reach 138 bytes, and the post-check
would not have prevented an overflow.
- Document the 0x02 check in sfr_data[0] as the VLAN table entry
valid flag.
Returns a JSON array of all configured VLANs with their IDs and names,
e.g. [{"id":1,"name":""},{"id":20,"name":"IoT"}].
The endpoint iterates VLAN IDs 1..4094 and filters by the validity bit
in sfr_data[0] (0x02), following the same pattern as vlan_create() and
vlan_setup() in rtl837x_port.c.
Also adds a small itoa16_html() helper for emitting decimal numbers
up to 4 digits (analogous to the existing 8-bit itoa_html()), used
for VLAN IDs which can reach 4094. Response builder uses the existing
vlan_name() helper for the name lookup, consistent with send_vlan().
Buffer overflow is prevented by breaking out of the iteration loop at
TCP_OUTBUF_SIZE - 60.
This endpoint is the foundation for upcoming UI improvements
(VLAN selector dropdown and overview table).
While the current implementation works for what it is actually used, it
is broken when trying to do larger transfers.
The length field in the control register has a size of 4 bits. In every
transfer, length+1 bytes are read. Thus, each transfer is limited to a
maximum of 16 bytes. Add a check for the length, and write the correct
value to the register.
Also update the loop in "sfp_send_data" to properly increment the output
register. Remove the unused special case for a length of 128 bytes.
When device has no LOS pin and module has no extended status, the
RX LOS value will not be shown. When both are present, the equality
check is performed. When only one is present, the present value
will be shown.
json from the switch, will still contain the field, but can be
null for when pin is not available.
The state of the SFP module is being already send in status.json,
but was not parsed via Web UI. When debuging SFP LOS/Signal detection
it is usefull to see what module is reporting back.
Extended the SFP mouse-over information with:
- RX LOS as reported in 0x02 bit of register 238
- External TX Disabled from 0x80 bit of register 238
- TX fault from 0x04 of the same register
- The last state of RX LOS pin (available also when there is no 0x40
option on the module)
This should help identify missing/incorrect setup of TX disabled pin.
I noticed that entering some vlan config, clicking "Update/Create", then
clicking "Get Configuration" resulted in Tagged/Untagged/PVID displaying
completely wrong data. It looks like the parisng in fetchVLAN() in
vlan.js was just completely disconnected from the layout of the
registers read by vlan_get() in rtl837x_port.c. Who knows how that
happened.
1. Fix fetchVLAN() member/untag parsing: the old code read bits [9:0]
as untagged and bits [10:19] as tagged, but the VLAN table register
layout is members in [9:0] and untag in [19:10]. Now correctly
derives tagged (member && !untag) and untagged (member && untag).
2. Add PVID to vlan.json response: PVID is stored per-port in separate
PVID registers (RTL837x_PVID_BASE_REG), not in the VLAN table entry.
The old code nonsensically tried to read it from bits [20:29] of the
VLAN table. Add port_pvid_get() and build a pvid bitmask in
send_vlan() so the JS can parse it correctly.
3. Remove auto-PVID logic from setC(): setC() is called by fetchVLAN()
while it's loading existing config, and so this logic mangled the
display of the existing config. Also, it doesn't make sense to
auto-set the PVID for tagged members (PVID relates to untagged
ingress.)
We use the SoC's UUID to generate a fixed MAC for a particular
switch device. The MAC generated uses a Realtek prefix and then
is followed by 3 bytes genertaed from the first 3 bytes of the
UUID xored with the last byte in order to prevent being able
to deduce the UUID from the public MAC.
RTL has up to 3 SCL pins and up to 4 SDA pins. Lets allow configuring
I2C with individual BUS numbers instead of 0/1 I2C.
This enables support for devices where SCL line is not shared between
SFP modules. MUX registry is now initialized depending on needed
pin function.
More over, some SFP pins require special MUX settings, lets initialize
those depending on SFP configuration. This adds TX Disable pin,
which right now is set to low at startup.
Caveats:
- We may still override MUX registry later
- Not sure how to handle invalid bus definitions
- Without SFP is it fine to *not* initialize anything?
- Do to RAM limitation we do inititalize output GPIO to low
bloqaudio
d00f
d00f
René van Dorst
Matt Merhar
Erdnusschokolade
logicog
feelfree69
feelfree69
Jan Hoffmann
logicog
diijkstra
Mark H. Spatz
TylerDurden-23
chriz