Both only ever served stp_fdb_update(), so they belong there. Internal RAM
has room for them on this branch and on the one that carries the
aggregation module too.
stp_enabled is a flag, so say bool. cmpBytes() returns a comparison
result, so say int8_t. The three busy waits this branch adds read the
status straight out of the SFR instead of copying four bytes to xdata
first.
A port held out of forwarding because a loop was seen on it stops hearing
the frames that justified the hold, so its BPDU age climbs. The auto edge
branch lives inside the same countdown as the hold, reads that age, and
promotes the port back to forwarding after three seconds. The loop opens,
a BPDU comes back, the block is applied again, and the two take turns.
Measured on a looped pair present when the tree came up: twenty cycles in
one window and fifteen in the next, each block followed by a promotion,
still going when the capture ended.
The countdown alone cannot tell a loop hold from an ordinary listen, so
record the hold and leave the port alone while it stands.
make clean left tools/output in place, so the host tools were never
rebuilt after a clean. SUBDIRSCLEAN, which builds the per-directory
clean target names for exactly that purpose, was defined but nothing
consumed it. Give clean and distclean those targets as prerequisites
and add the rule that runs the subdirectory's own clean, which
tools/Makefile already provides.
tcpip_output() decides whether to splice in the 802.1Q tag, and that
decision also moves the frame: the header is shifted forward over its
padding, so a tagged frame starts at uip_buf with the q_frame layout,
while an untagged one keeps the padding and the nonq_frame layout.
nic_tx_packet() took that decision a second time, from management_vlan
alone. That agreed while the sender suppressed the management VLAN around
the transmission, but not since the tag is skipped per frame for a
CPU-tagged one: the descriptor then still sits behind the padding while
the transfer is set up for the shifted layout. The frame goes out four
bytes early and its length is read from the offset where tx_seq and
chksum_flags live, so a sixty byte BPDU is sent as around 1800 bytes of
whatever follows it. Looped back it is no longer a BPDU, the port hears
nothing, auto edge promotes it and the loop stays open.
Record the decision where it is taken and let the transfer follow it.
A variable rather than an argument because internal RAM is full once the
aggregation module shares the image: the overlay area ends at 0x7f, and
an argument or any temporary for the condition no longer fits.
Both conflicts are the register keyword removal meeting a change of ours,
so each takes main's signature and keeps what the branch was saying:
nic_rx_packet() still returns a bool, and port_ingress_filter_get() stays
declared.
main has since put its own copy of the STP module in BANK2, so the pragma
this branch carried is now duplicated. The one with main's comment stays.
Generate wrong address for `a4` location.
Both on read from and write to a __sfr32 variable.
Workaround:
Use two __sfr16 instead of one __sfr32.
We still get some optimalizations / better code gen.
The preamble scan cursor and the buffered-length parameter carry no
state between calls, so they do not need static xdata slots. As plain
locals the compiler places both in registers, trimming 64 bytes of
BANK1 code and two bytes of xdata.
The offsets shared by config_take() stay static: direct data space is
fully allocated on machines like the SWTGW218AS, so plain locals there
add overlay bytes that no longer link, and xdata-class locals spill
three temporaries into direct space while growing the code by roughly
120 bytes. Document pre_acc, whose accumulation across TCP segments is
why it must remain global.
A firmware upload previously ended in a silent connection close, leaving
the client unable to distinguish a verified upload from a failed one.
Send an explicit 200/400 verdict with the CRC result, with
Content-Length so the browser completes the response before the reset,
and only reset the chip once the verdict has been fully ACKed.
The unconditional close after a config upload is gone since the
buffered config path answers with its own response, so drop the
now-unreachable close hack from the streaming path.
A firmware image cannot be buffered whole, so the upload is streamed to
flash, and stream_upload() already resumes across TCP segments. The
multipart preamble did not: handle_post() walked the part headers from the
start of whichever segment it held, so a client that split inside the
octet-stream part header lost its place, never started streaming, and the
request hung. Firefox splits exactly there, right after filename=".
Buffer the multipart body only until the octet-stream part header is
complete, locate the payload, then stream from that point; later segments
stream as before. The header reuses the configuration buffer, which is idle
during a firmware upload, so no extra memory is needed.
cmd_parser.c conflicted twice: main rewrote the pvid command around the
new port-separator and atoi helpers, next to the line where this branch
delegates "stp" to stp_parse(). Both belong, so the STP delegation keeps
main's pvid body.
The linker caught what the merge could not see: main changed atoi_byte()
to return the digit count and leave the value in atoi_results_u8, where
it used to return non-zero on failure and write through a pointer. Note
the sense is inverted, so the three calls in rtl837x_stp.c are adjusted
rather than just re-arranged.
This branch moved rtl837x_pins to the common window in eaff953 to reclaim
BANK2 for the per-port status work, which was free at the time because the
module was only the I2C and GPIO pin helpers.
main has since put the SFP EEPROM transfer there, so the module now weighs
934 bytes and the common window is 156 bytes short. BANK2 has room for it
again, and that is where main keeps it.
Common segment +934 bytes, BANK2 -934.
Only httpd.c conflicted: main added the buffered configuration upload
next to the pointers this branch had moved into xdata to free internal
RAM. Both belong, so the new globals sit above declarations that keep
their storage class.
All entry points are already __banked and none of the code runs in
interrupt context, so the module can leave the resident bank. This
relieves pressure on bank 0, which no longer fits a machine with a
custom init table.
d00f
logicog
René van Dorst
bloqaudio
feelfree69
donbernhardo