The window could be armed from the serial console but only ever disarmed
by an HTTP request. save_cmd, which gates arming, is cleared only while
execute_config() replays the startup config, so every interactive command
armed it wherever it was typed, while mgmt_alive, which disarms it, was
written in exactly one place, on HTTP traffic. An operator working
entirely on the serial console therefore lost STP 180 seconds after
enabling it however much they typed, which is what makes the mechanism
impossible to test from a console.
The documentation described the behaviour that was intended rather than
the one that was built, and in both directions: it said a command on the
serial console also confirms, and it said a reboot with STP in the
startup config disables it again three minutes later. Neither held. The
replay path never armed the window at all.
Repairing the asymmetry would have kept a mechanism whose premise is
contested anyway. A watchdog that switches the protection off in response
to silence adds a second failure mode on top of the first: where the
network is misconfigured and STP is the thing holding a storm back,
restoring forwarding removes the last reason management still answers.
Gone with it: the stp failsafe command, the fs and fsT fields of
/stp.json, the input and the tripped banner on the Spanning Tree page,
the two persistence patterns in config.js, the documentation section, and
mgmt_alive itself, which had no other reader.
550 bytes back, 145 of BANK1 and 405 of BANK2, and five of xdata, which
is the four counters and mgmt_alive and nothing else. Built for
SWTGW218AS and KP_9000_6XHML_X2 on sdcc 4.5.0.
Bring the Spanning Tree page in line with a typical managed switch's
per-port panel. Configuration gains the full-range path cost (raw
0..200000000, 0 = auto, replacing the old 1000x-scaled byte), a
point-to-point admin control (auto/on/off), and the priority is now a
0..240 step-16 dropdown. A new status table shows, per port, the Port
State, Role, Designated Bridge / Port ID / Cost (learned from received
BPDUs, kept per port and aged via the BPDU age), Operational Edge and
Operational Point-to-Point.
The designated fields fall back to presenting this switch as the
segment's designated bridge when no fresh BPDU has been heard (so a
quiet port shows our own bridge-id, as the vendor UIs do). /stp.json
carries the packed hex fields plus our own MAC for that fallback.
Space: reclaim BANK2 for the above by moving rtl837x_pins to HOME and
compacting leds_dump into a register-address table (~800B); bandwidth
returns to BANK1. No BANK3 - hardware-verified that PSBANK > 2 crashes
this SoC at boot (a bricked unit and an SPI-programmer recovery earlier
today); a warning to that effect is now in rtl837x_lldp.c.
Hardware-verified: cost 200000000 and p2p off round-trip through the CLI
and JSON, the status table populates correctly with STP enabled (all
ports Forwarding/Designated, oper-edge and oper-p2p True), LACP 3f/3f
and the LAN unaffected.
(cherry picked from commit 2ec62072f061dc9e78bc821ba1c297cb6819e206)
Enabling STP on a bridge whose management rides an in-band VLAN can cut
off that very management - and not only by our own blocking: on this
network the upstream TP-Link Easy Smart switch's "loop prevention"
reacted to our BPDU hellos by blocking ITS port towards us while our
ASIC was all-forwarding, isolating the whole segment until a power
cycle. Recoverable only by going quiet.
Add a commit-confirm watchdog: while STP is enabled, any HTTP request
re-arms a countdown ("stp failsafe <seconds>", default 180, 0 disables);
if management stays silent for the whole window, STP disables itself,
which also stops BPDU TX so a neighbour's loop protection can release
its block. The web UI polls /stp.json every 2 s, so an open browser
naturally keeps the watchdog re-armed. The trip is reported via
/stp.json (fs, fsT) and as a warning on the Spanning Tree page.
Deliberately not conditioned on our own MSTP port states - the incident
above proves the uplink can be dead while every local port forwards.
Also bound the NIC DMA busy-waits (nic_tx_packet, nic_rx_header,
nic_rx_packet): an unbounded spin on SFR_NIC_CTRL freezes the entire
main loop (timers, HTTP, ARP) if the ASIC ever fails to consume a
transfer; give up after ~65k polls and drop the frame instead.
Hardware-verified end to end: with priority 15 against a live RSTP
bridge the uplink died 6 s after "stp on" and the network recovered BY
ITSELF 66 s later (trip at 45 s + neighbour release), fsT=1, LACP and
LAN intact. Telemetry via syslog-to-edge-port host confirmed the full
chain: countdown 44->4, trip, hello TX stopping at the trip.
(cherry picked from commit 1fa9775156fd6d7ebfdda2382f73430b86601230)
Implements the standard 802.1D-2004/802.1w configuration surface:
Bridge: priority (0-15 x4096), hello time, max age, forward delay,
force-version (RSTP v2 / STP-compatible v0 Config BPDUs), tx hold
count (per-port per-second BPDU budget).
Per port: enable, admin edge (forwarding immediately - no listen gap),
auto edge (forwarding after 3 s of BPDU silence; DEFAULT, so
host-facing ports no longer take the full forward delay),
path cost (0=auto/20000), port priority, BPDU guard (port disabled
on BPDU receipt), root guard (never accept a better root on the
port), BPDU filter (no BPDUs in or out).
Engine additions: root max-age expiry (reclaim the tree when the root goes
silent), root path cost accounting (rx cost + root-port cost, advertised in
our BPDUs), loop detection (our own BPDU coming back blocks the port for a
listen period), topology-change counter, approximated per-port roles
(Root/Designated/Alternate) for diagnostics.
CLI: "stp prio|hello|maxage|fwd|txhold|version ..." and
"stp port <n> on|off|edge|cost|prio|guard|filter ..." (stp_parse, delegated
from cmd_parser); all forms accepted by the startup-config validator so the
whole configuration persists. /stp.json now reports config + status; the
Spanning Tree page exposes everything with immediate-apply controls and live
state/role columns (edit-in-flight guard against the 2 s refresh).
8051 memory: the module moves to code BANK2; internal-RAM pressure from
cross-bank calls resolved by xdata loop iterators/scratch, __reentrant on
the small helpers, and moving httpd's header-pointer globals to xdata.
Verified on hardware (SWTGW218AS): defaults land per standard; priority and
hello change live; admin-edge ports (the LACP bond uplinks) keep the LAN at
0% loss THROUGH "stp on"; auto-edge ports forward after 3 s; a port that
heard real BPDUs (a VM bridge behind physical port 6) correctly declined
auto-edge, sat out the full listen period and became Designated; tc counts
promotions; we win the root election at priority 16384 vs 32768.
(cherry picked from commit 09a34dc6acdc81ab9cab0727d2f4a59c68131a3e)
Add a Spanning Tree page: an on/off toggle driving the existing "stp"
command over /cmd, and a live status section fed by a new /stp.json
endpoint - the elected root bridge (priority + MAC), our path cost,
whether we are the root, and the per-port STP state read live from the
ASIC's MSTP register (same 2-bit encoding stp_setup() writes). Ports are
reported by their physical numbers.
Recovered-from: 3132319, 9365c86
d00f