sfp_read_reg() sat in rtlplayground.c, so it occupied the common 16 KB
window that every bank shares, even though nothing outside the SFP paths
calls it. That window is the tightest resource in the image:
SWTG024AS_V2_0 and SWTG024AS_A_2_0_1_5C_1SFP had 54 bytes left in it.
rtl837x_pins.c is already in BANK2 and already holds the I2C bus helpers
this function calls, so the transfer belongs there. The function moves
verbatim and becomes __banked; the prototype in rtl837x_common.h says so,
which is what keeps the callers in BANK1 and BANK2 honest.
No behaviour change. The common segment gains 200 bytes on every machine:
159 to 359 free on SWTGW218AS, 54 to 254 on the two variants above.
BANK1 +6 bytes, BANK2 +336. Built on sdcc 4.5.0.
sfp_read_reg() waited for the transfer to finish and then read the output
register whatever the outcome, so an address nothing acknowledged came back
as an ordinary byte and no caller could tell it apart from data. The vendor
SDK looks at bit 1 of the control register for exactly this, and we did
not.
A failure now sets sfp_i2c_fail and the read returns 0xff, which is already
the value sfp_apply_quirks() reads as either a failed transfer or a voltage
the spec does not allow, so that test starts being true when it should be.
The insertion path and the sfp command clear the flag first and say so
afterwards, rather than presenting the bytes as though they came from the
module.
What this deliberately does not do is act on the failure. Skipping
sds_config() when the rate read failed is the obvious next step, but a
module that raises the bit spuriously would then never be configured at
all, which is worse than what happens today, and I have no way to judge how
often the bit is right. That decision belongs with someone holding the
board.
It also leaves the other half of the rewrite alone, reading and writing up
to sixteen bytes per transaction. doc/sfp.md describes only the single byte
path and does not name a length field, and guessing at a register I cannot
test is how the last attempt at this function went wrong.
40 bytes of the common segment, 51 of BANK2 and 1 of xdata, nothing in
BANK1 or internal RAM. Built for SWTGW218AS and KP_9000_6XHML_X2 on sdcc
4.5.0. Not tested on hardware: shorting the clock line, as in #342, should
now print the failure line instead of a plausible looking byte.
Adds an optional per-board mac_flash_offset. When non-zero, RTLPlayground
reads a 6-byte MAC from that flash address and uses it if it is a valid
globally-administered unicast address; otherwise it falls back to the
generated locally-administered MAC. Offset 0 (default for every board)
preserves current behaviour.
Enable it for the SWTGW218AS, whose stock firmware keeps the factory MAC
in nvcfg at 0x1FC000. RTLPlayground images and web upgrades only touch
flash below that region, so the factory MAC survives flashing.
Move the MAC-derived default name out of main() into its own function and
call it after execute_config(), returning early when the config already
set a name - a configured switch then does no work for it at all.
The body deliberately has no local variables. Locals here - counters and
pointers alike - land in the 8051's internal-RAM overlay, and on an image
with LACP and STP both enabled that overlay is exhausted: a loop makes the
linker fail with "Could not get 8 consecutive bytes in internal RAM for
area OSEG". Moving the code into its own function does not help, since the
overlay is shared across the whole image, and hoisting the locals to xdata
does not either, because itohex() is inline and brings its own frame. This
only shows up in an integrated build; the branch on its own links fine.
Suggested-by: vDorst
Every switch came up as "RTLPlayground", so several of them on one
network were indistinguishable until someone configured a name. Append
the last three MAC octets (e.g. RTLPlayground-1ef924) - unique in
practice, still recognisable, and any "hostname ..." line in the startup
config overrides it as before.
Suggested-by: plaes
Add a device hostname settable from the CLI (`hostname <text>`) and the
System Settings page. The value is sanitized on ingest to JSON-safe
printable ASCII (<=23 chars), stored in a shared __xdata buffer, seeded
to "RTLPlayground" at boot, persisted through the startup-config, and
reported in /information.json. It lives in the common header so other
modules can advertise it (LLDP uses it as the System Name TLV).
Broaden range of SFP+ rates mapped to SDS_10GR
A commonly used SFP+ form-factor 10GBASE-LR (Hisense LTF1303-BH+) reports 0x62( BR Nominal: 9800MBd) at
power on and then switches to 0x64 after booting up.
0x62 -> 9.8gbps
0x63 -> 9.9gbps
0x64 -> 10gbps
0x6f -> 11.1gbps
0x70 -> 11.2gbps
These are outside of the previous 0x63-0x6f range which prevented the link from ever being brought up. So I changed the range to 0x62-0x6f
On a QSFPTEK QT-SFP+-T (RTL8261C) 10GBase-T module, the diag type field
(92) comes back as 0x00, but there's actually some statistics available
like temperature. Other metrics may be hard-coded values.
Add a basic struct that allows matching on vendor and/or model, using a
bitfield to allow multiple quirks for a given SFP module. Only
SFP_QUIRK_DDM is implemented.
For modules matching SFP_QUIRK_DDM, attempt an I2C read of the MSB of
module voltage during probe if DDM is "unsupported" - if it's not 0xff,
override the reported options so we can pull the diagnostic data.
To allow simpler comparisons, convert the ASCII fields (vendor,
model, serial) from space-padded to standard NULL-terminated strings.
strcmp() is moved from httpd.c to rtlplayground.c alongside other string
functions and shared between them.
The __reentrant keyword is used for the new functions to avoid using up
additional OSEG space. This allocates the variables on the stack, which
is OK for this particular code path.
The JSON assembly in send_status() is slightly modified to treat the
sfp_module_* data as standard NULL-terminated strings, and a repeated
subtraction was moved into a uint8_t to declutter the code.
A commonly used SFP+ form-factor XGS-PON ONT (WAS-110) reports 0x63 at
power on and then switches to 0x64 after booting up.
0x63 -> 9.9gbps
0x64 -> 10gbps
These are outside of the previous 0x66-0x69 range which prevented the
link from ever being brought up.
__sbit is for SFRs, for regular data __bit should be used.
Otherwise the variables is not correctly declared in the BSEG
section, leading to bit temporaries being allocated in the same
location.
When this causes the tx_buf_empty to be overwritten to 0, then
the next write_char will hang forever.
While the current implementation works for what it is actually used, it
is broken when trying to do larger transfers.
The length field in the control register has a size of 4 bits. In every
transfer, length+1 bytes are read. Thus, each transfer is limited to a
maximum of 16 bytes. Add a check for the length, and write the correct
value to the register.
Also update the loop in "sfp_send_data" to properly increment the output
register. Remove the unused special case for a length of 128 bytes.
Blocking by design to prevent loading config
Button must be held between 10 and 30 seconds to trigger reset.
If held more than 30 seconds, boot normally. This is to prevent lock-up in case of weird hardware variants.
Added new `vlan show` command to dump current VLAN settings.
Supports printing PVID & ingress filtering per port.
Added new `ingress [p]<mode>` command to setup ingress filtering.
Added wrappers for enabling/disabling vlan filtering. Currently
not configurable, but state in console is read via ASIC registers.
Full VLAN dump & web support of new commands will be added later.
The state of the SFP module is being already send in status.json,
but was not parsed via Web UI. When debuging SFP LOS/Signal detection
it is usefull to see what module is reporting back.
Extended the SFP mouse-over information with:
- RX LOS as reported in 0x02 bit of register 238
- External TX Disabled from 0x80 bit of register 238
- TX fault from 0x04 of the same register
- The last state of RX LOS pin (available also when there is no 0x40
option on the module)
This should help identify missing/incorrect setup of TX disabled pin.
d00f
bloqaudio
René van Dorst
d00f
Sempr
Matt Merhar
logicog
TylerDurden-23
feelfree69
UAb5eSMn
feelfree69
Tobias Diedrich
Jan Hoffmann
logicog
bennydiamond
diijkstra
chriz