A VLAN name is copied into vlan_names with nothing checking vlan_ptr
against VLAN_NAMES_SIZE. The only limit is the 128 byte command line, so
enough named VLANs walk straight off the end of a 1 kB table.
What sits immediately behind it makes this worse than a plain overflow: at
0x048A comes vlan_ptr itself, the index driving the write, then port_names
and cmd_buffer. Once the index is corrupted the following writes land
wherever it now points, and the configuration is replayed at boot, so a
config file that overflows does it again on every start.
Measure the name first and refuse it if the three id digits, the name, its
separating space and the terminator would not fit. The check goes before
vlan_name_remove() so a name that does not fit cannot take the existing one
with it, and the VLAN still gets its ports: dropping the whole line would
lose port membership during a config replay, which is worse than losing a
name.
The copy walks a pointer instead of indexing vlan_names[vlan_ptr++] each time,
and the word offset comes out of cmd_words_b once. Writing the bound as
VLAN_NAMES_SIZE - 5 folds the constant at compile time instead of adding it on
every call. BANK2 ends up 25 bytes smaller than it was before the check
existed.
Fold the "group with no ports" case into the argument-count guard
(cmd_words_len < 3) instead of a separate check, and accept only "d" for
delete, dropping the longer "delete" spelling. Update the serial-console
docs to match.
Two small things about the same command.
The usage line offered "lag <1-4> [port]...", which leaves out "lag show" even
though that is the only way to see the groups, so the one subcommand a reader
most needs is the one the error does not mention.
And a group number with no ports after it quietly wiped the group. That is a
reasonable thing to want and an unreasonable thing to do by accident, as it is
one fat-fingered return away from a bare "lag 1". It now takes "lag 1 delete"
or "lag 1 d", and a bare group number prints the usage instead.
Nothing changes for a saved configuration: "lag 1 5 6" is what gets written and
what gets replayed, and neither the old bare form nor the new delete matches
the pattern that decides what is persisted.
The CPU's own MAC exists in the L2 table only as a learned entry,
created whenever the CPU transmits, and it ages out like any other
dynamic entry. Unknown unicast is not flooded to the CPU port, so on an
idle switch (no web session, no management traffic) the entry expires
after the aging time and frames for the management IP no longer reach
the CPU: pings die until the next CPU transmission (an ARP reply)
re-teaches the entry, then die again. Real management sessions keep the
entry alive continuously, which is why this is only visible on idle
switches.
Install a static entry for the management MAC on the CPU port after the
startup config has been replayed, so it lands in the final management
VLAN, and move it when the management VLAN is changed at runtime.
Entry mechanics, established on hardware: a table write with read-method
0 hashes the key in TBL_DATA_IN and places the entry itself (a search
returns index 0 on a miss, there is no software-visible insertion slot).
The age field in the third data word must be non-zero for the entry to
be visible to lookup at all, and the static flag (bit 0 of byte 1 of
that word) stops the aging engine from decrementing it: with the flag a
full-age entry survives untouched where an identical unflagged entry
ages to invisible within the aging period. With no management VLAN
configured the entry lives in VLAN 1.
The pointer is masked when it advances over the command text, then
incremented once more for the newline without masking, so it can come to
rest one past the end of the ring.
Both readers walk from the pointer with their own index masked every
step, so an index that sits outside the ring is never reached and the
walk does not end. `history` on the console spins there, and so does
`/cmd_log`, which the web page fetches whenever settings are saved: it
fills the transmit buffer and keeps going past it.
The member mask is filled with a loop that stops one short, so the
highest front panel port never gets its bit and stays isolated from the
port that was just opened up. Every other loop over the port range in
the tree treats machine.max_port as the last port rather than the one
past it.
stp_enabled is a flag, so say bool. cmpBytes() returns a comparison
result, so say int8_t. The three busy waits this branch adds read the
status straight out of the SFR instead of copying four bytes to xdata
first.
The hand rolled loop was here because atoi_short() reported "no digits"
but not overflow, so 65540 would have wrapped to 4 and opened a
connection to a port nobody asked for. #326 gave it the same bound this
loop was carrying, so the reason is gone.
Zero still covers all three ways to be wrong, except that "no digits"
and overflow now come back as a zero return and port zero as a zero
value, so both are tested.
Three xdata scratch variables go with the loop.
The loop tested the digit range and the overflow bound with separate ifs,
on the strength of a comment saying the joined form makes sdcc park a
boolean in the bit area, and that an image carrying LACP and STP as well
is one bit short of needing a third byte of it. Measured on this branch
that is not what happens: the joined form links, the bit segment is
unchanged at fourteen bits overall and nine in cmd_parser, and BANK2
comes out ten bytes smaller.
The claim was about an image this branch does not build, and no branch
currently carries LACP, STP and this parser at once, so there is nothing
left to check it against. A justification nobody can verify, for a shape
nobody would otherwise write, is worse than no comment at all.
Behaviour is unchanged. The two forms agree on every input from 0 to
99999 and on the edges: empty, non digits, trailing junk, leading zeros,
65535 and 65536.
The note about atoi_short() stays, because that one still reports "no
digits" without reporting overflow. #326 replaces it with a version that
does both, and this should move onto it once that lands.
The port was frozen at 514 in the call that opens the connection, so a
collector listening anywhere else was simply out of reach, and plenty do,
because 514 is privileged and containerised collectors usually get a high
port instead. Working around it meant putting a proxy in front, which then
rewrites the source address and hides which device actually sent the line.
Add `syslog port <n>`. The default stays 514, so nothing changes for an
existing configuration. Setting it tears the connection down and builds a
new one, the same dance the address already does, because uip_udp_new()
freezes the port into the connection.
The value is parsed here rather than through atoi_short(), which reports
"no digits" but not overflow: 65540 would quietly wrap to 4 and we would
open a connection to a port nobody asked for. Checking before each multiply
keeps it in 16-bit arithmetic. Zero then covers all three ways to be wrong -
no digits, past 65535, or an explicit "0", which is not a port either.
Whitelist the new command in config.js as well, next to `syslog ip`, or the
line is dropped without a word when the configuration is saved and the
setting quietly fails to survive a reboot. The dedup entry has to precede
the general `^syslog\b` one, otherwise it would deduplicate against
`syslog on`.
itoa_short() is new: itoa() only handles a byte and print_short() prints
hex, so there was no way to show a port as a decimal number. Kept separate
from itoa() rather than widening it, because every existing caller passes a
byte and would start paying for 16-bit divisions it does not need.
The scratch variables for the parser live in xdata. Locals there would take
internal RAM, and this image has none left: data ends at 0x77, the overlay
occupies 0x78-0x7f and the stack starts at 0x80. Measured: no module's DSEG
grew.
cmd_parser.c conflicted twice: main rewrote the pvid command around the
new port-separator and atoi helpers, next to the line where this branch
delegates "stp" to stp_parse(). Both belong, so the STP delegation keeps
main's pvid body.
The linker caught what the merge could not see: main changed atoi_byte()
to return the digit count and leave the value in atoi_results_u8, where
it used to return non-zero on failure and write through a pointer. Note
the sense is inverted, so the three calls in rtl837x_stp.c are adjusted
rather than just re-arranged.
Only httpd.c conflicted: main added the buffered configuration upload
next to the pointers this branch had moved into xdata to free internal
RAM. Both belong, so the new globals sit above declarations that keep
their storage class.
Removing the CPU-port support, As stated in #334, it is not needed to
manual add the CPU-port to any command. Because the CPU-port should be
added automatilly when CPU-port is needed.
Refactor cmd_parse_port() because port number is only 1 byte.
This simplifies the parsing code.
Refactor cmd_parse_port_separator() to ensure the return size is correct.
cmd_parse_port_separator() parse the full port number and checks that the
number end with a NUL of space.
Now this function can also be used to parse the last argument number
because this ends with a NUL.
Also refactor code.
The I2C controller transfers up to sixteen bytes per transaction and
page_impl.c already used that for sfp_send_data(), while sfp_read_reg()
asked for one byte and every caller looped. Reading a module therefore
cost one address phase per byte: 87 transactions when a module is
inserted, 52 for the sfp command, 36 for the vendor block in status.json.
sfp_read_block() replaces sfp_read_reg() and the callers that already
wanted a run of registers ask for it once: the vendor fields as three
16 byte pages, the diagnostics as one transfer, rate and encoding
together. That drops the three paths above to 8, 6 and 3 transactions,
and sfp_send_data() loses its copy of the transfer.
The vendor loops now run over 16..63 rather than 20..59 so the page base
is a multiple of sixteen and the index into the buffer is a single AND.
The four extra bytes at each end are read and discarded. The diagnostics
read asks for 16 bytes rather than the 15 it uses, because 16 is a width
the shipped firmware already exercises and 15 is not.
The device address, the bus selection and the start bit go into the
control register in one write now that the memory address is written
first, so a transfer touches that register once instead of three times.
The register reads take their result from the SFRs directly rather than
through the sfr_data mirror. The result is a bool and the destination is
sfp_buf, so a caller that cares about a failed transfer looks at the
return value instead of a flag.
Every caller gives up on the first failed read rather than carrying a
flag to the end, which is why the module read moved out of handle_sfp
into a function of its own. A module whose read fails is left marked as
absent, so the next poll retries it instead of configuring the SerDes
from bytes that never arrived.
BANK1 -194 bytes, BANK2 +382, common segment +44, xdata +15 for the
buffer, and one byte more of internal RAM free than before the series.
Built for all 25 machine definitions on sdcc 4.5.0; the tightest common
segment is 98 bytes free on SWTG024AS_V2_0, against 54 before this
series.
The variable lives in rtlplayground.c, so it is declared in rtl837x_common.h
with the others there, and it follows the naming of the rest.
The header carried comments on the externs that the definitions in
rtl837x_stp.c repeat, sometimes differently, which is one place too many to
keep in step. What only the header had, the value ranges and what the
designated arrays hold, moved to the definitions; the rest is gone. Function
declarations lost their comments too.
The status printer only prints, so its running commentary went. A define
replaces the bare 33 in stp_in(), and the note on the loop check is down to
what applies at that line.
Implements the standard 802.1D-2004/802.1w configuration surface:
Bridge: priority (0-15 x4096), hello time, max age, forward delay,
force-version (RSTP v2 / STP-compatible v0 Config BPDUs), tx hold
count (per-port per-second BPDU budget).
Per port: enable, admin edge (forwarding immediately - no listen gap),
auto edge (forwarding after 3 s of BPDU silence; DEFAULT, so
host-facing ports no longer take the full forward delay),
path cost (0=auto/20000), port priority, BPDU guard (port disabled
on BPDU receipt), root guard (never accept a better root on the
port), BPDU filter (no BPDUs in or out).
Engine additions: root max-age expiry (reclaim the tree when the root goes
silent), root path cost accounting (rx cost + root-port cost, advertised in
our BPDUs), loop detection (our own BPDU coming back blocks the port for a
listen period), topology-change counter, approximated per-port roles
(Root/Designated/Alternate) for diagnostics.
CLI: "stp prio|hello|maxage|fwd|txhold|version ..." and
"stp port <n> on|off|edge|cost|prio|guard|filter ..." (stp_parse, delegated
from cmd_parser); all forms accepted by the startup-config validator so the
whole configuration persists. /stp.json now reports config + status; the
Spanning Tree page exposes everything with immediate-apply controls and live
state/role columns (edit-in-flight guard against the 2 s refresh).
8051 memory: the module moves to code BANK2; internal-RAM pressure from
cross-bank calls resolved by xdata loop iterators/scratch, __reentrant on
the small helpers, and moving httpd's header-pointer globals to xdata.
Verified on hardware (SWTGW218AS): defaults land per standard; priority and
hello change live; admin-edge ports (the LACP bond uplinks) keep the LAN at
0% loss THROUGH "stp on"; auto-edge ports forward after 3 s; a port that
heard real BPDUs (a VM bridge behind physical port 6) correctly declined
auto-edge, sat out the full listen period and became Designated; tc counts
promotions; we win the root election at priority 16384 vs 32768.
(cherry picked from commit 09a34dc6acdc81ab9cab0727d2f4a59c68131a3e)
The single-digit arm of the ingress parser guards with p - '1' > 9,
which no digit can satisfy: the largest, '9', gives 8. The digit that
needed rejecting is '0', which gives -1 and indexes one byte before
phys_to_log_port, so "ingress 0 t" reads out of bounds and applies the
ingress mode to whatever port number that byte happens to contain.
Ports are 1-based, so reject anything below '1'; values above '9' are
already excluded by the isnumber check before this.
parse_isolate() accepted a two digit port and mapped it to logical port 9,
the CPU port, while port_isolate() and port_isolation_get() both refuse
anything above machine.max_port. Setting the isolation of the CPU port was
therefore declined without a word and reading it always answered no
members, whatever the hardware held.
Bound the port to the front panel, so the command says what it does. The
digit is checked before it indexes phys_to_log_port[], which a non numeric
argument used to read past.
handle_rx() dispatched to igmp_packet_handler() on the destination
address alone, so an ordinary IGMPv3 report off the wire reached the
handler and could write a table entry whether or not anyone had asked
for snooping. The STP branch right above it is gated on stpEnabled;
this brings the IGMP branch in line.
Snooping state lived only in the per-port registers, and the receive
path cannot afford to read one per packet, so the flag shadows it:
igmp_enable() sets it, igmp_setup() clears it, and igmp_setup() runs
from both the boot path and "igmp off".
While here, igmp off becomes an explicit subcommand instead of the
fall-through, and an unrecognised igmp subcommand prints the usage
line rather than silently turning snooping off.
Six bytes of BANK1 and one of xdata, no internal RAM.
d00f
René van Dorst
bloqaudio
logicog
d00f