The firmware has a single management VLAN (one management_vlan variable),
so a stored config should never carry more than one "vlan N mgmt" line.
When parsing a mgmt command, drop any previously stored mgmt entry so
repeatedly changing the management VLAN no longer accumulates stale lines.
parseConf() only recognized "port N name" in conf_cmds, so "port N <speed>"
lines were treated as unknown commands and dropped on save - configured port
speeds never persisted.
Add the speed command (incl. optional half/full duplex suffix) to conf_cmds,
add a "port N" entry to conf_overwrite so re-saving a speed replaces the
previous value, and guard the per-port name entry so changing a port's speed
no longer wipes its configured name.
The vlan/mgmt lookahead split (commit dcc60c3) correctly separated the
patterns so that `vlan N mgmt` and `vlan N <members>` match different
conf_overwrite entries. But the filter that applies the overwrite still
used `item.startsWith(matchStr + " ")` with matchStr = "vlan N", which
also matches "vlan N mgmt" — so the management entry was removed whenever
the VLAN's membership definition was re-saved.
Example: with both `vlan 44 management 2t 4t 5 6t` and `vlan 44 mgmt`
in the config, changing the membership dropped `vlan 44 mgmt` entirely.
Added a `!item.endsWith(" mgmt")` guard so management entries survive the
filter. No reordering is needed: `vlan N mgmt` only sets the global
management_vlan variable (cmd_parser.c) and does not depend on the VLAN
table entry existing, so its position in the config is irrelevant.
The pattern /^vlan\s+\d{1,4}\b/ matched both VLAN membership entries
(vlan N <ports>) and management entries (vlan N mgmt), causing them
to overwrite each other in configuration[]. When saving, whichever
form came last in the cmd_log would dedupe the other out of the
final config — resulting in either lost membership or a stale mgmt
setting.
Split into two patterns using negative lookahead:
- /^vlan\s+\d{1,4}\s+mgmt$/ matches only mgmt entries
- /^vlan\s+\d{1,4}(?!\s+mgmt\b)/ matches everything else
Both dedup independently. Discovered via hardware test on 6XH-X
where 'vlan 44 mgmt' silently dropped 'vlan 44 management 2t 5u'
from saved config, locking out web UI on next boot.
Multiple related bugs in the Save-to-Flash path:
1. Multipart upload was missing the required filename argument,
causing the backend parser to fail. Added 'config.txt' to the
form.append call. This was likely the primary reason Save-to-Flash
was unreliable.
2. Web UI was not pausing its polling interval during flash write,
causing CPU contention and intermittent crashes. Added isSaving
lock and clearInterval before sendConfig.
3. conf_cmds whitelist was incomplete. Added: syslog, passwd, pvid,
ingress, port name, lag, laghash, isolate, stp, igmp, mtu, bw,
vlan N mgmt, vlan N d.
4. VLAN regex blocked named VLANs. New pattern allows optional name
(starts with letter, matching CLI parser semantics).
5. vlan N d (delete) was not persisted. parseConf now removes the
matching vlan N ... entry from configuration[] when seeing a
delete command, without storing the delete itself. Result: the
saved config describes the end state.
6. configuration[] was not cleared between flashSave invocations,
leading to stale entries from prior interactions.
7. conf_overwrite boundary fix: 'pvid 1' no longer matches 'pvid 10'
etc. Added trailing space in startsWith check.
8. All conf_cmds patterns now anchored with ^...$ for full-line
match. parseConf normalizes whitespace before testing.
9. Port range widened to \d{1,2} so ports 11+ are accepted.
Structural fixes (1, 2, 6, 7, 8) ported from mcaptur's closed PR #219;
remaining fixes (3, 4, 5, 9) and overall regex strategy are new.
The hardware bitmask format encodes both "untagged members" and
"non-members" in the upper 10 bits (per doc/vlan.md). The existing
fetchVLAN() correctly masks this with the membership bitmask before
display, but loadVlanTable() did not, causing non-member ports to
appear in the Untagged Ports column.
Tested on KeepLiNK KP-9000-6XH-X.
Below the configuration form, a new table lists all configured VLANs
with their port memberships: Member, Tagged, Untagged, and PVID
columns. Port ranges are formatted compactly (e.g. "1-2,5").
Port-to-bit mapping uses the existing physToLogPort[] array populated
by /status.json, so the table is consistent with the icon view in
fetchVLAN() and works on any supported machine.
Each row has a delete button that sends "vlan N d" via /cmd, with
a confirmation dialog. VLAN 1 cannot be deleted (no button shown).
Table and dropdown both refresh automatically after Update/Create
and after delete via a new refreshVlanViews() helper.
The N+1 request pattern (1x /vlanlist + Nx /vlan.json) keeps the
backend simple and avoids buffer overflow risks for systems with
many VLANs. For typical configurations (<50 VLANs), page load
remains under one second.
A new <select> element above the VLAN ID input lets users pick an
existing VLAN by name instead of typing the ID. Options are loaded
from /vlanlist on page load and re-loaded after successful
Update/Create operations.
Selection triggers the existing fetchVLAN() flow.
Falls back gracefully if /vlanlist returns an empty list or fails:
the dropdown is hidden and the existing ID input remains functional.
When device has no LOS pin and module has no extended status, the
RX LOS value will not be shown. When both are present, the equality
check is performed. When only one is present, the present value
will be shown.
json from the switch, will still contain the field, but can be
null for when pin is not available.
The state of the SFP module is being already send in status.json,
but was not parsed via Web UI. When debuging SFP LOS/Signal detection
it is usefull to see what module is reporting back.
Extended the SFP mouse-over information with:
- RX LOS as reported in 0x02 bit of register 238
- External TX Disabled from 0x80 bit of register 238
- TX fault from 0x04 of the same register
- The last state of RX LOS pin (available also when there is no 0x40
option on the module)
This should help identify missing/incorrect setup of TX disabled pin.
I noticed that entering some vlan config, clicking "Update/Create", then
clicking "Get Configuration" resulted in Tagged/Untagged/PVID displaying
completely wrong data. It looks like the parisng in fetchVLAN() in
vlan.js was just completely disconnected from the layout of the
registers read by vlan_get() in rtl837x_port.c. Who knows how that
happened.
1. Fix fetchVLAN() member/untag parsing: the old code read bits [9:0]
as untagged and bits [10:19] as tagged, but the VLAN table register
layout is members in [9:0] and untag in [19:10]. Now correctly
derives tagged (member && !untag) and untagged (member && untag).
2. Add PVID to vlan.json response: PVID is stored per-port in separate
PVID registers (RTL837x_PVID_BASE_REG), not in the VLAN table entry.
The old code nonsensically tried to read it from bits [20:29] of the
VLAN table. Add port_pvid_get() and build a pvid bitmask in
send_vlan() so the JS can parse it correctly.
3. Remove auto-PVID logic from setC(): setC() is called by fetchVLAN()
while it's loading existing config, and so this logic mangled the
display of the existing config. Also, it doesn't make sense to
auto-set the PVID for tagged members (PVID relates to untagged
ingress.)
Erdnusschokolade
logicog
UAb5eSMn
René van Dorst
logicog
feelfree69
feelfree69
Jan Hoffmann
diijkstra
Mark H. Spatz
chriz
TylerDurden-23