With UIP_CONF_MAX_CONNECTIONS set to one, a verified upload can leave
reset intent set when its response is never acknowledged. A subsequent
TCP connection reuses that slot, and ACKing its plain GET response can
otherwise trigger reset_chip(). This is sequential slot reuse, not
concurrent HTTP connections.
Store reset intent in the connection appstate and initialize both tstate
and fw_reset_pending on every uip_connected() event, regardless of stale
appstate contents. Reset only after the verified upload response is fully
acknowledged.
Exercise the real HTTP callback for all stale tstate bytes, sequential
slot reuse and a later GET, partial/final ACKs, abort, timeout and CRC
failure. Keep the regression tests in the existing tab-indented style.
Dynamic link aggregation on top of the static LAGG, for RTL8372/8373:
receive, selection and mux state machines (coupled mux, one aggregator
per group), with "lacp show" to look inside. Each of the four trunk
groups runs its own aggregator on the candidate ports assigned with
"lag <n> lacp <ports>"; the engine starts with the first such group and
stops with the last.
LACPDUs reach the CPU through the reserved-multicast trap, so delivery
needs no L2 entry and nothing written per VLAN or per PVID. The trap
acts on the address before the VLAN lookup and before the ingress
filters, so a LACPDU also arrives on a port that admits tagged frames
only and on a port STP holds in blocking, neither of which a forwarded
one reaches. A trapped frame carries no VLAN tag,
so lacp_in() takes the offset of the PDU body from TRAP_RX_BODY(). The
action is set with trap_rma_set(), which leaves the flags sharing that
register alone, and "lacp off" puts the slow-protocols drop default
back. doc/lacp.md and doc/link_aggregation.md record what was measured,
including why the trap looked like a dead end at first.
The web UI gets a Static/LACP mode per group on the LAG page with live
status, and the startup-config validator knows the per-group syntax. A
host-side sandbox for the state machines runs in the test harness
together with the LAG hash check. It drives both forms of an incoming
LACPDU, so the body offset of a trapped one is covered as well.
The L2 table page iterated with the "next unicast" read method, so
static multicast entries such as an IGMP group were invisible. It now
iterates with "next address", skips L3 entries (their layout carries IP
addresses where a MAC is expected), and reports the lowest member of a
multicast entry's port mask, so such an entry shows up as a static
entry on that port.
A port taken out of LACP forgets its partner, so "lacp show" after
"lacp off" no longer reports one. Applying the same candidate set to a
group again, as the LAG page does on every Apply, leaves the trunk
alone instead of tearing it down for a second or two. lacp_in() checks
the frame length and ethertype before reading a LACPDU, so a runt or a
foreign frame on the slow-protocols address cannot leave stale buffer
bytes as a partner. The sandbox covers these three in T20-T22. On the
LAG page, LACP mode with no ports checked sends "lag N lacp off", and
the startup-config validator wants at least one port after "lacp".
boot_to_html outputs 1 and 0 not true and false, making the sim match
the real implementation.
lldp.json has a hanging , in the array; so overwriting it
A matrix of the ports, one row per ingress port, showing which ports a
frame entering there may leave through. The port number of a row turns
red when the port is not fully open, and the cell for the port itself is
marked since it is always allowed. Apply sends one "isolate" command per
changed row, and Allow all ticks the whole matrix.
The switch side is a new /isolation.json, which reports each port's
allowance mask read back from the hardware. The page is an Isolation
section of the single-page UI.
Building with SDCC 4.6.0 emits tons of warnings e.g.:
cmd_parser.c:31: warning 356: object in read-only code space should be const
cmd_parser.c:36: warning 357: pointer to object in read-only code space should be pointer to const
These of course become fatal when building with --Werror.
Comparing resultant binaries, it seems that a single string is shifted
(deduplication?) but the numbers emitted at the end of the build are
otherwise identical.
The TODO next to the disabled TCP checksum code asks which bit of the RX tag
carries the result. It is bit 2 of byte 1: the hardware sets it when the L4
checksum is bad.
That answers the question for UDP as well, which was not being checked either
because UIP_CONF_UDP_CHECKSUMS is 0. Both paths now read the flag instead of
running a checksum over the payload on the 8051.
A zero UDP checksum, which is optional in IPv4, is not flagged by the hardware,
so DHCP keeps working and no extra condition is needed.
rx_headers lives in rtlplayground.c, which the host tests do not link, so
test_httpd_tx carries the storage itself the way it already carries uip_buf.
A zeroed descriptor reads as a good checksum, so the existing scenarios are
unaffected.
A new scenario sets the flag on a request and expects it counted as a checksum
error and left unanswered, then sends the same request with the flag clear and
expects it served. Built against uip.c without this change, those first two
checks fail and the two control checks still pass, so the scenario tells the
two versions apart rather than merely exercising the code.
Costs 156 bytes of code on SWTGW218AS and no extra XDATA.
Drives the unmodified httpd.c and uip.c through a handshake and a GET
from a client that moves its receive window, and compares the bytes that
reach the wire with the file they are meant to carry. The served file
holds a position-dependent pattern, so a repeat or a gap is reported at
its offset rather than as content that differs somewhere.
The first scenario holds the window still and must pass: it is the check
that the bench itself is sound, before the two moving-window scenarios
are believed.
avicarmeli
bloq
João Silva
DrDoof
Rob Emery
Matt Merhar