The comments repeated the documentation, described tests or explained
the code to its author. What stays describes the LACPDU structures. The
timer constants are decimal, in units of the LACP timer.
Listing by next-address also returned the reserved-multicast entries STP
writes, shown as port 1 with a delete button, while l2_delete() still
looks up by next-unicast and so removed the unicast entry after that
index instead. The change was there to show the LACP steering entries;
delivery by trap writes none, so it goes.
Dynamic link aggregation on top of the static LAGG, for RTL8372/8373:
receive, selection and mux state machines (coupled mux, one aggregator
per group), with "lacp show" to look inside. Each of the four trunk
groups runs its own aggregator on the candidate ports assigned with
"lag <n> lacp <ports>"; the engine starts with the first such group and
stops with the last.
LACPDUs reach the CPU through the reserved-multicast trap, so delivery
needs no L2 entry and nothing written per VLAN or per PVID. The trap
acts on the address before the VLAN lookup and before the ingress
filters, so a LACPDU also arrives on a port that admits tagged frames
only and on a port STP holds in blocking, neither of which a forwarded
one reaches. A trapped frame carries no VLAN tag,
so lacp_in() takes the offset of the PDU body from TRAP_RX_BODY(). The
action is set with trap_rma_set(), which leaves the flags sharing that
register alone, and "lacp off" puts the slow-protocols drop default
back. doc/lacp.md and doc/link_aggregation.md record what was measured,
including why the trap looked like a dead end at first.
The web UI gets a Static/LACP mode per group on the LAG page with live
status, and the startup-config validator knows the per-group syntax. A
host-side sandbox for the state machines runs in the test harness
together with the LAG hash check. It drives both forms of an incoming
LACPDU, so the body offset of a trapped one is covered as well.
The L2 table page iterated with the "next unicast" read method, so
static multicast entries such as an IGMP group were invisible. It now
iterates with "next address", skips L3 entries (their layout carries IP
addresses where a MAC is expected), and reports the lowest member of a
multicast entry's port mask, so such an entry shows up as a static
entry on that port.
A port taken out of LACP forgets its partner, so "lacp show" after
"lacp off" no longer reports one. Applying the same candidate set to a
group again, as the LAG page does on every Apply, leaves the trunk
alone instead of tearing it down for a second or two. lacp_in() checks
the frame length and ethertype before reading a LACPDU, so a runt or a
foreign frame on the slow-protocols address cannot leave stale buffer
bytes as a partner. The sandbox covers these three in T20-T22. On the
LAG page, LACP mode with no ports checked sends "lag N lacp off", and
the startup-config validator wants at least one port after "lacp".
Needed to increase buffer size for this to send app.js
The logical port status is what is returned in the array, for
non-sequential systems we need to map through physToLog rather
than just subtracting 1
physToLog is 1 based! not 0; also fixing up typecasts
Reimplementing using an array of objects to represent ports.
The previous approach of a bitmask of logical ports, was just too
simple on devices such as the SWGT024_V2_0_MANAGED which has
gaps in the port assignments.
timing with ticks
Fixing up the log_to_phys_port assignment
2000 is about every 10 seconds, so scaling up to once every 30ish
Removing the attempt to block lldp frames,
This does not work however the hard work has been done for us in
the #514 so we can borrow that work later on
boot_to_html outputs 1 and 0 not true and false, making the sim match
the real implementation.
lldp.json has a hanging , in the array; so overwriting it
Moving the global on/off onto the LLDP page
Building a table of LLDP status from the S ports. Later on, if
we wish to implement an lldp receiver we can display the remote
details here
Adding support to the cmd parser for the lldp commands
A matrix of the ports, one row per ingress port, showing which ports a
frame entering there may leave through. The port number of a row turns
red when the port is not fully open, and the cell for the port itself is
marked since it is always allowed. Apply sends one "isolate" command per
changed row, and Allow all ticks the whole matrix.
The switch side is a new /isolation.json, which reports each port's
allowance mask read back from the hardware. The page is an Isolation
section of the single-page UI.
Storm control used meters 0 to 39, the same meters the ACL hands out,
so a storm limit and an acl meter could overwrite each other. It now
uses 24 + port * 4 + type, meters 24 to 63.
parse_storm() is no longer reentrant and uses plain locals, looks the
type up in a while loop and returns straight from the one-line cases.
storm_show() uses plain locals too.
The documentation says how IGMP decides between mcast and umcast, how
to get from a meter index to its limit, where the IFG bit of a meter
is, and what an ingress bandwidth limit on the same port does to the
storm limit.
Building with SDCC 4.6.0 emits tons of warnings e.g.:
cmd_parser.c:31: warning 356: object in read-only code space should be const
cmd_parser.c:36: warning 357: pointer to object in read-only code space should be pointer to const
These of course become fatal when building with --Werror.
Comparing resultant binaries, it seems that a single string is shifted
(deduplication?) but the numbers emitted at the end of the build are
otherwise identical.
The row sits between Hardware and Flash. The firmware sends the formatted string
rather than the raw register, since the System table prints its values as they
arrive.
Costs 186 bytes in BANK1.
The vendor, model and serial strings are filtered while the EEPROM read
fills the buffers, so the page copies them out as they are. NUL still
ends a string, so a field shorter than its slot reads the same as before.
The three loops in send_status() become one call each. strcpy() cannot
return the length: rtl837x_common.h hides that prototype under
RTLP_HOST_TEST so host builds take the C library version, and a call
that adds its result to slen does not compile there. A small static
helper does the copy instead, and bank 1 drops by 96 bytes.
A port named NAS"1 made status.json unparsable, so the page stopped
loading, and the name survives a reboot in the saved config. VLAN names
and the SFP strings have the same problem.
They now go through a helper that replaces ", \ and non-printable bytes
with a dot, the way the hostname is already sanitized on ingest. The
length does not change, so the size checks still hold.
The helper also covers the 0xa0 byte that send_sfp_info() skipped as a
special case, so that check is gone.
Compiling these two files for the host turns up warnings that SDCC does
not print: four places mix & with | and two mix && with ||, and l2_delete
keeps a counter it never reads. The parentheses only say what the
compiler already does, so the generated code is unchanged.
counter_to_html() reads the SFRs directly for the zero test, which saves
14 bytes of bank 1.
send_status wrote the high and the low word of a packet counter one after
the other, each without its leading zeros. That reads fine until a port
passes four billion packets; from then on a low word of 5 prints as "0x15"
next to a high word of 1, and the rates the page derives from the
difference between two readings jump around. send_counters already padded
the low word, so both now share one helper that pads it only when the high
word is set, which also drops the leading "0" the counters page used to
print in front of every small value.
The session cookie carried neither Expires nor Max-Age, so browsers that
clean up session cookies aggressively (LibreWolf, for one) may drop it
while the session is still valid. Send Max-Age=session_timeout so the
declared lifetime matches the timeout already enforced by the firmware.
itoa16_html() only converted four digits, so extend it to five to print
timeouts up to 65535. That also fixes information.json, which used the
same helper and reported wrong values from 10000 s up.
Adds a numeric input next to the syslog settings to read and set the
session timeout without knowing the command. The current value is
reported in information.json, so the field also shows the default the
firmware was built with.
Costs 86 bytes of code (BANK1) and nothing in RAM.
Save to flash ran the stored config through the same filter as the
command log, so stored lines the page does not know were dropped. The
stored lines are now carried over as they are and only the log is
filtered.
ingress only changes the ports it lists, but the merge replaced every
stored ingress line. It now merges per port; "ingress t|u|a" still
replaces everything, and per-port settings an all-ports line already
overrode are not revived.
Write from the config editor no longer clears the command log or the
unsaved marker, since the edited text does not hold the changes made on
other pages; only Save, which merges them, clears the log.
The command log grows from 1 kB to 2 kB, which still fits the 2500 byte
output buffer, and send_cmd_log() stops at the end of that buffer.
Spanning tree so far saw only physical ports. Two ports aggregated towards
the same neighbour look to the protocol like two parallel paths, so it
blocks one of them and cuts the group in half.
Give each of the four groups an STP entity of its own, numbered above the
physical ports. A member port answers to its group: BPDUs arriving on it
are accounted to the entity, the entity's state is written to every member
together, and its BPDUs carry the state of a live member. Ports outside
any group keep behaving exactly as before.
Membership comes from the aggregation tables once a second; when it
changed, the entity's state is reapplied to the new set of members. The
CLI takes lag <1-4> wherever it takes port <n>, the web UI shows a group
as one row, and the saved config keeps the lag form of the commands.
A device on an aggregate is learned against whichever member the frame came in
on, and the hash moves that around: the same address changes port every time
the flow mix changes. The table was telling the truth and there was no way to
read it, since nothing on the page or the console says those two ports are one
link.
port_lag_of() already exists and already knows the answer, so both views ask
it. The console prints LAG1 in place of the member, and /l2.json carries a
"lag" field beside the port, 0 when the port stands alone, which is the shape
/stp.json already uses.
Costs 151 bytes of BANK1.
The /cmd path carried its own copy of the plain-text response header,
which was the same string page_impl.c already keeps in
HTTP_RESPONCE_TXT, minus one difference: the shared one never said
Connection: close.
This httpd closes after every response, so a reply that does not
advertise it invites the browser to reuse the socket and lose the next
request. HTTP_RESPONCE_JSON has always said so; the text one was the
odd one out, and send_config() and send_cmd_log() were answering
without it.
The copy is gone and the shared string carries the header. The check
for a command that printed nothing now compares against the length
strtox() returned instead of sizeof() on the macro.
Test the busy flag and compare the entry's MAC against the SFR data
registers directly instead of going through the sfr_data copy, and
rewrite TBL_DATA_0 in place rather than reassembling all four bytes.
Smaller and faster on the deepest httpd path.
Suggested-by: vDorst
The L2 page's Delete button removes any table entry by index, including
the entry for the switch's own MAC on the CPU port. Without that entry
unicast to the management address is no longer delivered to the CPU, so
management goes dark until the CPU happens to transmit again and the
entry is relearned. Compare the entry's MAC against uip_ethaddr before
rewriting it and answer result 0 for the switch's own address, as for a
missing entry. The compare is inline: this handler sits at the bottom of
the uIP call chain, where every extra call level costs internal RAM.
The enabled flag is a flag, so say bool. The header length no longer needs
to live in xdata: it was put there when a local would not link, and there
is room for it here.
The overview names the row after the JSON key, so the syslog row said
"syslog_server_ip" while carrying only an address. It now says
"syslog_server" and carries the port with it.
An empty slot used to read back 0xa0 per byte and the filter dropped it,
so the field came out empty. Block reads report the failure instead and
leave the buffer alone, and these two callers ignored that and printed
what the last successful read had left there.
Say nothing when there is nothing to read, which is what the other eight
callers of sfp_read_block() already do.
Both conflicts are the register keyword removal meeting a change of ours,
so each takes main's signature and keeps what the branch was saying:
nic_rx_packet() still returns a bool, and port_ingress_filter_get() stays
declared.
main has since put its own copy of the STP module in BANK2, so the pragma
this branch carried is now duplicated. The one with main's comment stays.
cmd_parser.c conflicted twice: main rewrote the pvid command around the
new port-separator and atoi helpers, next to the line where this branch
delegates "stp" to stp_parse(). Both belong, so the STP delegation keeps
main's pvid body.
The linker caught what the merge could not see: main changed atoi_byte()
to return the digit count and leave the value in atoi_results_u8, where
it used to return non-zero on failure and write through a pointer. Note
the sense is inverted, so the three calls in rtl837x_stp.c are adjusted
rather than just re-arranged.
Only httpd.c conflicted: main added the buffered configuration upload
next to the pointers this branch had moved into xdata to free internal
RAM. Both belong, so the new globals sit above declarations that keep
their storage class.
The I2C controller transfers up to sixteen bytes per transaction and
page_impl.c already used that for sfp_send_data(), while sfp_read_reg()
asked for one byte and every caller looped. Reading a module therefore
cost one address phase per byte: 87 transactions when a module is
inserted, 52 for the sfp command, 36 for the vendor block in status.json.
sfp_read_block() replaces sfp_read_reg() and the callers that already
wanted a run of registers ask for it once: the vendor fields as three
16 byte pages, the diagnostics as one transfer, rate and encoding
together. That drops the three paths above to 8, 6 and 3 transactions,
and sfp_send_data() loses its copy of the transfer.
The vendor loops now run over 16..63 rather than 20..59 so the page base
is a multiple of sixteen and the index into the buffer is a single AND.
The four extra bytes at each end are read and discarded. The diagnostics
read asks for 16 bytes rather than the 15 it uses, because 16 is a width
the shipped firmware already exercises and 15 is not.
The device address, the bus selection and the start bit go into the
control register in one write now that the memory address is written
first, so a transfer touches that register once instead of three times.
The register reads take their result from the SFRs directly rather than
through the sfr_data mirror. The result is a bool and the destination is
sfp_buf, so a caller that cares about a failed transfer looks at the
return value instead of a flag.
Every caller gives up on the first failed read rather than carrying a
flag to the end, which is why the module read moved out of handle_sfp
into a function of its own. A module whose read fails is left marked as
absent, so the next poll retries it instead of configuring the SerDes
from bytes that never arrived.
BANK1 -194 bytes, BANK2 +382, common segment +44, xdata +15 for the
buffer, and one byte more of internal RAM free than before the series.
Built for all 25 machine definitions on sdcc 4.5.0; the tightest common
segment is 98 bytes free on SWTG024AS_V2_0, against 54 before this
series.
send_config() streams a configuration larger than the TCP output buffer
through the cont_addr/cont_len continuation, but set cont_addr to the
offset within the config instead of a flash address, so the tail was read
from code space. The file server sets cont_addr absolute; do the same by
adding CONFIG_START.
The bug was unreachable while CONFIG_UPLOAD_BUF capped uploads below
TCP_OUTBUF_SIZE, but a stored config near the full sector exposes it.
The variable lives in rtlplayground.c, so it is declared in rtl837x_common.h
with the others there, and it follows the naming of the rest.
The header carried comments on the externs that the definitions in
rtl837x_stp.c repeat, sometimes differently, which is one place too many to
keep in step. What only the header had, the value ranges and what the
designated arrays hold, moved to the definitions; the rest is gone. Function
declarations lost their comments too.
The status printer only prints, so its running commentary went. A define
replaces the bare 33 in stp_in(), and the note on the loop check is down to
what applies at that line.
d00f
René van Dorst
Rob Emery
gnacho
feelfree69
Matt Merhar
eraiza0816
feelfree69
bloqaudio
logicog