__sbit is for SFRs, for regular data __bit should be used.
Otherwise the variables is not correctly declared in the BSEG
section, leading to bit temporaries being allocated in the same
location.
When this causes the tx_buf_empty to be overwritten to 0, then
the next write_char will hang forever.
While the current implementation works for what it is actually used, it
is broken when trying to do larger transfers.
The length field in the control register has a size of 4 bits. In every
transfer, length+1 bytes are read. Thus, each transfer is limited to a
maximum of 16 bytes. Add a check for the length, and write the correct
value to the register.
Also update the loop in "sfp_send_data" to properly increment the output
register. Remove the unused special case for a length of 128 bytes.
Blocking by design to prevent loading config
Button must be held between 10 and 30 seconds to trigger reset.
If held more than 30 seconds, boot normally. This is to prevent lock-up in case of weird hardware variants.
Added new `vlan show` command to dump current VLAN settings.
Supports printing PVID & ingress filtering per port.
Added new `ingress [p]<mode>` command to setup ingress filtering.
Added wrappers for enabling/disabling vlan filtering. Currently
not configurable, but state in console is read via ASIC registers.
Full VLAN dump & web support of new commands will be added later.
The state of the SFP module is being already send in status.json,
but was not parsed via Web UI. When debuging SFP LOS/Signal detection
it is usefull to see what module is reporting back.
Extended the SFP mouse-over information with:
- RX LOS as reported in 0x02 bit of register 238
- External TX Disabled from 0x80 bit of register 238
- TX fault from 0x04 of the same register
- The last state of RX LOS pin (available also when there is no 0x40
option on the module)
This should help identify missing/incorrect setup of TX disabled pin.
The presence of the main function is a hardcoded trigger in sdcc that causes
the interrupt vectors and atomic rollback helpers to be generated as part of
compilation of the file containing the main function.
This makes sure the runtime library is correctly initialized and reduces
crtstart.asm to contain only the banked call helpers.
To ensure that the __interrupt_vect in area HOME is located at the beginning
of the firmware, the linker flags are updated to set the HOME start to
0x00000 and the linker object order is modified to have rtlplayground.rel
first.
Generated code in rtlplayground.asm:
```
;--------------------------------------------------------
; interrupt vector
;--------------------------------------------------------
.area HOME (CODE)
__interrupt_vect:
ljmp __sdcc_gsinit_startup
ljmp _isr_ext0
.ds 5
ljmp _isr_timer0
.ds 5
ljmp _isr_ext1
.ds 5
reti
.ds 7
ljmp _isr_serial
.ds 5
ljmp _isr_timer2
.ds 5
reti
.ds 7
reti
.ds 7
ljmp _isr_ext2
.ds 5
ljmp _isr_ext3
; restartable atomic support routines
.ds 2
sdcc_atomic_exchange_rollback_start::
nop
nop
sdcc_atomic_exchange_pdata_impl:
movx a, @r0
mov r3, a
mov a, r2
movx @r0, a
sjmp sdcc_atomic_exchange_exit
nop
nop
sdcc_atomic_exchange_xdata_impl:
movx a, @dptr
mov r3, a
mov a, r2
movx @dptr, a
sjmp sdcc_atomic_exchange_exit
sdcc_atomic_compare_exchange_idata_impl:
mov a, @r0
cjne a, ar2, .+#5
mov a, r3
mov @r0, a
ret
nop
sdcc_atomic_compare_exchange_pdata_impl:
movx a, @r0
cjne a, ar2, .+#5
mov a, r3
movx @r0, a
ret
nop
sdcc_atomic_compare_exchange_xdata_impl:
movx a, @dptr
cjne a, ar2, .+#5
mov a, r3
movx @dptr, a
ret
sdcc_atomic_exchange_rollback_end::
sdcc_atomic_exchange_gptr_impl::
jnb b.6, sdcc_atomic_exchange_xdata_impl
mov r0, dpl
jb b.5, sdcc_atomic_exchange_pdata_impl
sdcc_atomic_exchange_idata_impl:
mov a, r2
xch a, @r0
mov dpl, a
ret
sdcc_atomic_exchange_exit:
mov dpl, r3
ret
sdcc_atomic_compare_exchange_gptr_impl::
jnb b.6, sdcc_atomic_compare_exchange_xdata_impl
mov r0, dpl
jb b.5, sdcc_atomic_compare_exchange_pdata_impl
sjmp sdcc_atomic_compare_exchange_idata_impl
```
This saves 508 bytes in the HOME area by:
- Getting rid of the expensive hex array indexing
- Having print_short and print_long delegate to print_byte
This is at the expense of increasing the stack depth a tiny bit.
Stack usage isn't an issue so far since I see ~96 bytes of
untouched stack memory.
The current code for entering commands via the serial CLI is completely
refactored and moved out of rtlplayground.c into a separate file cmd_edit.c
putting code into BANK2.
The serial ring buffer sbuf[] is now exclusively used for receiving
keys, including escape sequences (DEL will generate a 4-byte escape
sequence). The command is now held in cmd_buffer. This reduces
XMEM use, because the serial buffer can be much smaller.
Supported is only editing the current command line via backspace, del,
cursor left and right.
Because the code cannot distinguish escape sequences which are not yet
complete (because the serial isr has not yet put all characters into
the serial buffer) from the dozens of unsupported ones (F-keys/home,
Page up/down, cursor up/down...) they are ignored and remain in the
serial buffer until the ring-pointer overwrites them. This is standard
behaviour for consoles, which will print out garbage for unsupported
characters. In this implementation, the command line buffer and the
visible command line in the terminal are always synced, so garbage
can be removed again by ediing the line.
The code makes several redundant checks in order to prevent race-conditions
between the serial ISR and the comand-editing code.
We use the SoC's UUID to generate a fixed MAC for a particular
switch device. The MAC generated uses a Realtek prefix and then
is followed by 3 bytes genertaed from the first 3 bytes of the
UUID xored with the last byte in order to prevent being able
to deduce the UUID from the public MAC.
feelfree69
logicog
René van Dorst
feelfree69
Tobias Diedrich
Jan Hoffmann
logicog
bennydiamond
diijkstra
chriz