Storm control used meters 0 to 39, the same meters the ACL hands out,
so a storm limit and an acl meter could overwrite each other. It now
uses 24 + port * 4 + type, meters 24 to 63.
parse_storm() is no longer reentrant and uses plain locals, looks the
type up in a while loop and returns straight from the one-line cases.
storm_show() uses plain locals too.
The documentation says how IGMP decides between mcast and umcast, how
to get from a meter index to its limit, where the IFG bit of a meter
is, and what an ingress bandwidth limit on the same port does to the
storm limit.
The server timeout is an inactivity timeout: scan_header() refreshes
last_session_use on every authenticated request. Max-Age counts from
login instead, and the cookie is only set there, so the browser deletes
it session_timeout seconds after logging in however busy the session
is. Leave expiry to the server, which already handles it.
The five-digit itoa16_html() stays: information.json must print
timeouts from 10000 to 65535 correctly.
edc469f made max_upload count, which bounds how many bytes a request may
carry. Nothing bounds where those bytes land. The two are not the same
check: the first watches the request, the second watches the flash address.
uptr walks forward one page at a time from FIRMWARE_UPLOAD_START and has no
ceiling. A body whose closing boundary never arrives keeps writing page after
page past the staging region, and on a flash exactly twice FIRMWARE_UPLOAD_START
the address wraps onto the running image at zero, so a bad upload takes the
working firmware with it. That commit's own message notes the related hazard:
flash_write_bytes() carries the address in three bytes and drops what does not
fit.
Bound it where uptr actually moves: refuse the next page once it would leave
the area check_and_flash_update_image() reads back, and answer 400. A partial
image left behind is harmless - boot rejects it on CRC and erases it.
This rebase drops the part of the original patch that removed max_upload;
the length limit and the address limit now sit side by side.
Building with SDCC 4.6.0 emits tons of warnings e.g.:
cmd_parser.c:31: warning 356: object in read-only code space should be const
cmd_parser.c:36: warning 357: pointer to object in read-only code space should be pointer to const
These of course become fatal when building with --Werror.
Comparing resultant binaries, it seems that a single string is shifted
(deduplication?) but the numbers emitted at the end of the build are
otherwise identical.
max_upload was armed once when the upload began and never reduced, so
`max_upload - uip_len > 0` was an unsigned expression that only went
false when a segment arrived whose length matched the limit exactly. The
write pointer climbed from the staging address with nothing to stop it,
while flash_write_bytes() carries the address in three bytes and drops
whatever does not fit.
Subtract each segment as it is taken and compare before subtracting, which
is what the comment there described. The limit was only ever armed for
firmware uploads; configuration uploads keep the bound their own buffer
already imposes.
The multipart branch for /config tests authenticated before it touches
anything; the branch for /upload does not, and the 401 for it is only
raised further down at the dispatch. By then the request has already set
config_upload, uptr, verify_crc, max_upload and pre_acc, and announced a
firmware upload on the console.
Those five are globals while the transfer state they steer is per
connection, and the stack is built for ten connections, so a request that
is about to be rejected can still retarget an upload another client is in
the middle of: a configuration upload continues as a firmware one and its
remaining parts are written to the staging area instead of the
configuration sector.
Apply the same test the neighbouring branch uses, before the assignments.
The row sits between Hardware and Flash. The firmware sends the formatted string
rather than the raw register, since the System table prints its values as they
arrive.
Costs 186 bytes in BANK1.
gcc flags the else whose only statement is dbg_string(), because that macro
expands to nothing unless DEBUG is on, leaving the branch with an empty body.
The line is older than this branch; the bench is simply the first thing that
compiles httpd.c with a host compiler and -Wall -Wextra.
Turn warnings into errors in the test Makefile too, so the next one is caught
where it appears instead of scrolling past. It is the only warning the four
test binaries produce, so nothing else has to change.
The replay takes a line of at most 126 bytes, so a longer one is skipped
on boot. Neither the upload path nor the editor looked at line length,
so the file the user saved was not the configuration the switch would
come up with.
Reject such a body in config_take(), before the sector is erased, which
the upload path already maps to 400. The editor points at the offending
line and its length, and measures it in bytes rather than characters, so
a name written in a non-ASCII script is counted the way the switch
counts it.
uip_mss() is the limit on the next segment, not a record of the last
one: uIP recomputes it from the window the peer advertises in every
incoming segment, before the application is called. The ACK path
subtracted it from slen and added it to o_idx, and the retransmit path
handed it to uip_send(), so whenever the window moved between a segment
going out and its ACK coming back, the file being served lost or
repeated the difference. A window shrinking from 1460 to 600 between the
two repeats 860 bytes under fresh sequence numbers, which a browser
writes into the file; a window opening the same way skips 860.
Remember the length in tx_send() and use it in both places. The
retransmit path then repeats exactly the segment uIP still counts as
outstanding, which is what uip_connr->len makes it put on the wire.
uip_appdata is void *, so p - uip_appdata subtracts pointers of
different types. SDCC accepts it, C does not, and no host compiler will
build the file for a unit test. Cast to the type the byte count is meant
in; the generated firmware code is unchanged.
The vendor, model and serial strings are filtered while the EEPROM read
fills the buffers, so the page copies them out as they are. NUL still
ends a string, so a field shorter than its slot reads the same as before.
The three loops in send_status() become one call each. strcpy() cannot
return the length: rtl837x_common.h hides that prototype under
RTLP_HOST_TEST so host builds take the C library version, and a call
that adds its result to slen does not compile there. A small static
helper does the copy instead, and bank 1 drops by 96 bytes.
A port named NAS"1 made status.json unparsable, so the page stopped
loading, and the name survives a reboot in the saved config. VLAN names
and the SFP strings have the same problem.
They now go through a helper that replaces ", \ and non-printable bytes
with a dot, the way the hostname is already sanitized on ingest. The
length does not change, so the size checks still hold.
The helper also covers the 0xa0 byte that send_sfp_info() skipped as a
special case, so that check is gone.
Compiling these two files for the host turns up warnings that SDCC does
not print: four places mix & with | and two mix && with ||, and l2_delete
keeps a counter it never reads. The parentheses only say what the
compiler already does, so the generated code is unchanged.
counter_to_html() reads the SFRs directly for the zero test, which saves
14 bytes of bank 1.
send_status wrote the high and the low word of a packet counter one after
the other, each without its leading zeros. That reads fine until a port
passes four billion packets; from then on a low word of 5 prints as "0x15"
next to a high word of 1, and the rates the page derives from the
difference between two readings jump around. send_counters already padded
the low word, so both now share one helper that pads it only when the high
word is set, which also drops the leading "0" the counters page used to
print in front of every small value.
The session cookie carried neither Expires nor Max-Age, so browsers that
clean up session cookies aggressively (LibreWolf, for one) may drop it
while the session is still valid. Send Max-Age=session_timeout so the
declared lifetime matches the timeout already enforced by the firmware.
itoa16_html() only converted four digits, so extend it to five to print
timeouts up to 65535. That also fixes information.json, which used the
same helper and reported wrong values from 10000 s up.
Adds a numeric input next to the syslog settings to read and set the
session timeout without knowing the command. The current value is
reported in information.json, so the field also shows the default the
firmware was built with.
Costs 86 bytes of code (BANK1) and nothing in RAM.
Save to flash ran the stored config through the same filter as the
command log, so stored lines the page does not know were dropped. The
stored lines are now carried over as they are and only the log is
filtered.
ingress only changes the ports it lists, but the merge replaced every
stored ingress line. It now merges per port; "ingress t|u|a" still
replaces everything, and per-port settings an all-ports line already
overrode are not revived.
Write from the config editor no longer clears the command log or the
unsaved marker, since the edited text does not hold the changes made on
other pages; only Save, which merges them, clears the log.
The command log grows from 1 kB to 2 kB, which still fits the 2500 byte
output buffer, and send_cmd_log() stops at the end of that buffer.
handle_post() takes the request path from byte 6 of the segment it is
given. For the first segment of a POST that is the path, but for a later
segment of a multipart upload it is whatever part of the file happens to
sit there. The cmd and login handlers were matched before the multipart
state was checked, so a segment of a config or firmware upload with
"cmd " at that offset ran the rest of the segment as CLI commands, and
one with "login " there aborted the upload with 400.
Check for an upload in progress, and for new upload and config requests,
before looking at cmd and login. A new POST cannot match both sets of
words, so nothing changes for requests that are not uploads.
session_id is cleared at boot and only a successful login fills it in,
while the uptime counter and last_session_use both start at 0. For the
first SESSION_TIMEOUT seconds after a start, a request carrying an empty
"Cookie: session=" therefore passes is_word_x(session, session_id) and
is treated as logged in, which is enough for /cmd, /config and /upload.
Only look at the cookie once a session has been handed out.
The session timeout was a compile-time constant (200 s), so changing it
meant rebuilding the firmware. Make it a variable that keeps the same
default and add a "session <seconds>" command, so it can be set from
the console or from the startup configuration like the other settings.
Measured on KP_9000_9XHML_X_V3_1: ROM +180 bytes (BANK1 +17, BANK2
+161) and xdata +2 bytes; the internal RAM map is unchanged.
The pages become one index.html holding every section, one app.js and a
self-contained login.html. The layout is a sidebar with light, dark and
Selenized themes (or follow the OS), a live dashboard with per-port
packet rates, and confirmation dialogs in front of the actions that can
lock the operator out.
Behaviour changes against the previous pages:
- every request goes through one queue that waits for the previous
response BODY rather than its headers: the firmware shares a single
output buffer across connections and delimits responses by closing,
so a second request in flight corrupts the first
- "Save to flash" merges the command log into the startup configuration
with the grammar the console accepts, shows the result before writing,
verifies the sector by reading it back and clears the command log only
after that; the header shows an "unsaved changes" badge while the
running configuration differs from flash
- the console section shows the output the firmware returns for a
command, including the parser's explanation on a rejected one
- the firmware update section checks size, bank header and CRC16 of the
image in the browser before uploading, shows upload progress and waits
for the switch to come back after the reset
- the ports table shows the learned MAC of a port when there is exactly
one and the count otherwise; the MAC table sorts per column, filters,
and names the LAG a learned address sits behind
- the spanning tree section sends only the settings that changed on
Apply instead of one command per control event
- link aggregation groups are numbered 1-4 like the command line, and
applying an empty group clears it
The translation table is inline in app.js with English, Japanese and
Chinese. The language selector sits in the page header and reloads the
page so that dynamically built tables are rebuilt in the new language.
Only login.html and the favicon are served before authentication; the
stylesheet, the port images and the old script bundle no longer exist.
The simulator's allowlist follows the firmware's.
The session timer was refreshed only when a page from the file table was
served, so a client that loads its pages once and then talks to the JSON
endpoints alone is logged out SESSION_TIMEOUT seconds after the load,
however busy it is. A firmware upload started after that point is answered
with 401 instead of a verdict. Refresh the timer wherever the session
cookie validates, which covers every authenticated request, and drop the
file-serving refresh that this makes redundant.
Spanning tree so far saw only physical ports. Two ports aggregated towards
the same neighbour look to the protocol like two parallel paths, so it
blocks one of them and cuts the group in half.
Give each of the four groups an STP entity of its own, numbered above the
physical ports. A member port answers to its group: BPDUs arriving on it
are accounted to the entity, the entity's state is written to every member
together, and its BPDUs carry the state of a live member. Ports outside
any group keep behaving exactly as before.
Membership comes from the aggregation tables once a second; when it
changed, the entity's state is reapplied to the new set of members. The
CLI takes lag <1-4> wherever it takes port <n>, the web UI shows a group
as one row, and the saved config keeps the lag form of the commands.
The lookup tables live in BANK1, so the routine switches the code bank to
reach them with movc and never switches it back. That is the contract the
__naked declaration already implied: same bank or common segment only.
The name now says it.
crc16_bank1 is the routine unchanged. crc16 becomes a __banked wrapper in
BANK1, so a caller from another bank has its own bank put back by
__sdcc_banked_ret. The two existing call sites take the direct path and
pay nothing.
A file larger than the output buffer is sent in two phases: the first
buffer goes out in MSS-sized pieces, with o_idx walking through it, and
what is left is then streamed from flash a chunk at a time into outbuf
from offset 0.
The continuation branch never reset o_idx, so it kept the offset the first
phase had left it at, while uip_rexmit() retransmits from outbuf + o_idx.
A lost continuation segment was therefore retransmitted as the bytes 1460
further into the buffer, which the client accepts as the missing data, and
with o_idx + slen past the 2500-byte buffer it also read whatever xdata
follows outbuf.
Reproduced on a SWTGW218AS by dropping 15% of the switch's TCP segments:
seven of eight fetches of a 21 kB static came back the right length and
the wrong content, each first differing at a fixed phase of the 1460-byte
chunk. With o_idx reset the retransmission repeats the chunk it sent.
The o_idx += slen right after slen = 0 went too: it added nothing.
(cherry picked from commit 789d29423288f89411a41673e26ce1854b296c3d)
uip_init() does not set uip_conn, and httpd_init() runs right after it, so
the assignment went through a pointer nothing had assigned yet.
It has stayed invisible because the startup code does clear xdata: uip_conn
is NULL rather than garbage, appstate sits 28 bytes into struct uip_conn, and
the byte therefore lands at xdata 0x1C. With the current map that is inside
the command line buffer, at an offset nothing reads while the line is empty,
and cmd_editor_init() runs later anyway.
Nothing is broken today, but it is a write to an address that has nothing to
do with the state being set, and it moves the moment the struct grows or the
map shifts. Address the connection directly.
A device on an aggregate is learned against whichever member the frame came in
on, and the hash moves that around: the same address changes port every time
the flow mix changes. The table was telling the truth and there was no way to
read it, since nothing on the page or the console says those two ports are one
link.
port_lag_of() already exists and already knows the answer, so both views ask
it. The console prints LAG1 in place of the member, and /l2.json carries a
"lag" field beside the port, 0 when the port stands alone, which is the shape
/stp.json already uses.
Costs 151 bytes of BANK1.
* uip: time out an ESTABLISHED connection whose peer went silent
uIP has no keepalive and no idle timeout for an ESTABLISHED connection, so
a peer that vanishes without FIN or RST holds it open forever. A crashed
client does it, and so does a SYN caught while the switch is still
booting. With UIP_CONF_MAX_CONNECTIONS = 1 that wedges the single slot:
the web UI stops answering, port 80 no longer even SYN-ACKs, and only a
power cycle recovers it. Every other TCP state already has an exit path
(UIP_MAXRTX, UIP_TIME_WAIT_TIMEOUT); idle ESTABLISHED was the one hole.
Close it inside uIP rather than in httpd, so any future TCP service is
covered too. The retransmission timer is unused while nothing is in
flight, so the idle count lives in it: a 1 Hz strobe derived from the
uip_periodic() rate ages it, any arriving segment clears it, and past the
limit the connection is aborted through the same path as UIP_MAXRTX. Two
new options in uipopt.h, default off; this project enables 30 s.
httpd also joins uip_timedout() to its cleanup: it only handled closed
and aborted, so both this timeout and the existing UIP_MAXRTX one would
have left the transfer state stuck on a dead connection.
* uip: keep the tuning values out of the prose
The comment named the timeout and the tick rate, which go stale the
moment either constant is edited. It now says why an idle connection
is aged out and leaves the numbers to the defines under it.
The /cmd path carried its own copy of the plain-text response header,
which was the same string page_impl.c already keeps in
HTTP_RESPONCE_TXT, minus one difference: the shared one never said
Connection: close.
This httpd closes after every response, so a reply that does not
advertise it invites the browser to reuse the socket and lose the next
request. HTTP_RESPONCE_JSON has always said so; the text one was the
odd one out, and send_config() and send_cmd_log() were answering
without it.
The copy is gone and the shared string carries the header. The check
for a command that printed nothing now compares against the length
strtox() returned instead of sizeof() on the macro.
DrDoof
gnacho
feelfree69
Matt Merhar
René van Dorst
bloqaudio
logicog
eraiza0816
feelfree69