lacp: implement IEEE 802.3ad link aggregation

Dynamic link aggregation on top of the static LAGG, for RTL8372/8373:
receive, selection and mux state machines (coupled mux, one aggregator
per group), with "lacp show" to look inside. Each of the four trunk
groups runs its own aggregator on the candidate ports assigned with
"lag <n> lacp <ports>"; the engine starts with the first such group and
stops with the last.

LACPDUs reach the CPU through the reserved-multicast trap, so delivery
needs no L2 entry and nothing written per VLAN or per PVID. The trap
acts on the address before the VLAN lookup and before the ingress
filters, so a LACPDU also arrives on a port that admits tagged frames
only and on a port STP holds in blocking, neither of which a forwarded
one reaches. A trapped frame carries no VLAN tag,
so lacp_in() takes the offset of the PDU body from TRAP_RX_BODY(). The
action is set with trap_rma_set(), which leaves the flags sharing that
register alone, and "lacp off" puts the slow-protocols drop default
back. doc/lacp.md and doc/link_aggregation.md record what was measured,
including why the trap looked like a dead end at first.

The web UI gets a Static/LACP mode per group on the LAG page with live
status, and the startup-config validator knows the per-group syntax. A
host-side sandbox for the state machines runs in the test harness
together with the LAG hash check. It drives both forms of an incoming
LACPDU, so the body offset of a trapped one is covered as well.

The L2 table page iterated with the "next unicast" read method, so
static multicast entries such as an IGMP group were invisible. It now
iterates with "next address", skips L3 entries (their layout carries IP
addresses where a MAC is expected), and reports the lowest member of a
multicast entry's port mask, so such an entry shows up as a static
entry on that port.

A port taken out of LACP forgets its partner, so "lacp show" after
"lacp off" no longer reports one. Applying the same candidate set to a
group again, as the LAG page does on every Apply, leaves the trunk
alone instead of tearing it down for a second or two. lacp_in() checks
the frame length and ethertype before reading a LACPDU, so a runt or a
foreign frame on the slow-protocols address cannot leave stale buffer
bytes as a partner. The sandbox covers these three in T20-T22. On the
LAG page, LACP mode with no ports checked sends "lag N lacp off", and
the startup-config validator wants at least one port after "lacp".

test/README.md

@@ -48,6 +48,8 @@ fires — so it drops straight into CI.
 | `test_port_tables` | `rtl837x_port.c` | VLAN entry layout and round trip, PVID register sharing, static multicast and management entries, per-port flush, trunk membership and hash seed |
 | `test_page_json` | `httpd/page_impl.c` + `rtl837x_port.c` | `/vlan.json`, `/vlanlist`, `/l2.json` (walk, wrap marker, paging inside `outbuf`), 64-bit counters in `/status.json` and `/counters.json` |
 | `test_httpd_tx` | `httpd/httpd.c` + `uip/uip.c` | a GET of a static file against a client that moves its receive window: ACK accounting, continuation chunks out of flash, retransmission |
+| `lacp/` | `rtl837x_lacp.c` | state machines against a simulated 802.3ad partner: convergence, mis-cabling, expiry, re-election, two groups, LACPDU containment entries |
+| `port_hash/` | `port_lag_members_set()` | a LAG seeds its own hash register |
 
 ## Adding a test for another module
 1. Write `test_<module>.c` with `main()` driving the module's entry points and