diff --git a/doc/devices/2M-PCB23-V3_2.md b/doc/devices/2M-PCB23-V3_2.md
new file mode 100644
index 00000000..706b44b4
--- /dev/null
+++ b/doc/devices/2M-PCB23-V3_2.md
@@ -0,0 +1,36 @@
+### 2M-PCB23-V3.2
+
+## Brands
+|Brand|Type|Managed|PCB|Flash|Chip RTL|
+|---|---|---|---|---|---|
+| keepLINK | KP-9000-9XHML-X | Yes|  2M-PCB23-V3.2 | 2M (Winbond 25Q) | |
+
+The original web interface reports this board as hardware version V3.2
+(original firmware V100.9.25, January 2026).
+
+## Compared to V3.1
+
+The component placement matches [2M-PCB23-V3.1](2M-PCB23-V3_1.md): same
+positions for the flash (U8), the T7/T8/T9/T10 headers, the SFP cage and its
+LED, and the unpopulated U7/U9 footprints. Build with
+`MACHINE=KP_9000_9XHML_X_V3_2`, which uses the V3.1 machine definition and
+only differs in the reported name.
+
+## Tested
+
+Installed from the original firmware through its web interface with
+`installer/output/rtlplayground_oem_upgrade.bin`, then:
+
+- RJ45 ports link at 2.5G; LEDs: orange at 2.5G, green below
+- SFP port: module detected with vendor/model/serial and DOM readings
+  (temperature, Vcc, TX bias, TX/RX power), link up at 10G
+- factory MAC read from flash (0x1FC000)
+- reset button (GPIO48): held for more than 10 s it restores the default config
+
+## Flash access
+
+Reading the flash in-circuit with a SOIC-8 clip did not work: the chip ID
+comes back as `EF FF FF` (only the manufacturer byte is right) and reads
+return 0xff, the same as on a V3.1 board. The switch chip is powered through
+the clip and keeps driving the SPI lines. Make sure a way back is acceptable
+before installing, or hold the switch chip in reset while reading.
diff --git a/doc/supported_devices.md b/doc/supported_devices.md
index 740ae1da..ee2d2c47 100644
--- a/doc/supported_devices.md
+++ b/doc/supported_devices.md
@@ -22,6 +22,7 @@ The following devices have been tested and are fully working:
 | Keeplink | KP-9000-6XH-X2 / KP-9000-6XHML-X2 | No/Yes | [2M-PCB43-V1.2 / V2.1](devices/KP-9000-6XH-X2.md) |       | 4 + 2 |
 | keepLINK | KP-9000-9XHML-X | Yes     | [2M-PCB23-V2.2](devices/2M-PCB23-V2_2.md)                                 | 2M    | 8 + 1 |
 | keepLINK | KP-9000-9XHML-X | Yes     | [2M-PCB23-V3.1](devices/2M-PCB23-V3_1.md)                                 | 2M    | 8 + 1 |
+| keepLINK | KP-9000-9XHML-X | Yes     | [2M-PCB23-V3.2](devices/2M-PCB23-V3_2.md)                                 | 2M    | 8 + 1 |
 | LIANGUO  | SWTG024AS       | No      | [SWTG024AS-v2.0-17452](devices/SWTG024AS.md)                              | 0.5M  | 4 + 2 |
 | Lianguo  | ZX-SWTGW215AS   | Yes     | [PCB-SWTG115AS-V2.0 / PCB-SWTG115AS-V2.1](devices/SWTGW215AS.md)          | 2M    | 5 + 1 |
 | Lianguo  | HYWS-SGT0108S   | No      | [2G5F_20G_V1.01](devices/HYWS-SGT0108S.md)                                | 0.5M  | 8 + 1 |
diff --git a/machine.c b/machine.c
index 01ec5767..aab941d6 100644
--- a/machine.c
+++ b/machine.c
@@ -237,9 +237,14 @@ __code const struct machine machine = {
 	},
 };
 
-#elif defined MACHINE_KP_9000_9XHML_X_V3_1
+#elif defined(MACHINE_KP_9000_9XHML_X_V3_1) || defined(MACHINE_KP_9000_9XHML_X_V3_2)
+// 2M-PCB23-V3.2 is wired like V3.1 (SFP detection, LEDs, factory MAC location)
 __code const struct machine machine = {
+#if defined(MACHINE_KP_9000_9XHML_X_V3_2)
+	.machine_name = "keepLink KP-9000-9XHML-X V3.2",
+#else
 	.machine_name = "keepLink KP-9000-9XHML-X V3.1",
+#endif
 	.isRTL8373 = 1,
 	.min_port = 0,
 	.max_port = 8,
diff --git a/machine.h b/machine.h
index cd393073..84367c2d 100644
--- a/machine.h
+++ b/machine.h
@@ -22,6 +22,7 @@
 // #define MACHINE_KP_9000_9XH_X_EU
 // #define MACHINE_KP_9000_9XHML_X_V2_2
 // #define MACHINE_KP_9000_9XHML_X_V3_1
+// #define MACHINE_KP_9000_9XHML_X_V3_2
 // #define MACHINE_SWGT024_V2_0_MANAGED
 // #define MACHINE_SWGT024_V2_0_UNMANAGED
 // #define MACHINE_TRENDNET_TEG_S562