Add Hi-K0402WS V2 hardware support (#391)

Signed-off-by: Pietro Ameruoso <p.ameruso@live.it>
Co-authored-by: Pietro Ameruoso <p.ameruso@live.it>

doc/devices/PCB-K0402WS-V2.0.md

@@ -0,0 +1,97 @@
+Hisource Hi-K0402WS V2
+
+RTL8372-based 4×2.5G + 2×SFP+ unmanaged switch.
+
+Using SPI clamp in-board is the only method for initial installation.
+
+### Label specifications
+
+- **Manufacturer**: HISOURCE
+- **Model**: Hi-K0402WS V2
+- **Ports**:
+  - 4 × RJ45: 10/100/1000/2500 Mbps
+  - 2 × SFP+: 1G / 2.5G / 10G
+
+### What works
+
+- All four 2.5GBASE-T RJ45 ports at 10/100/1000/2500 Mbps
+- Both SFP+ ports supporting 1G, 2.5G and 10G modules
+- LEDs: amber (2.5G) and green (1G/100M/10M) per copper port; combined link/act on SFP ports
+
+### PCB overview
+
+**Board markings**
+- PCB-K0402WS-V2.0
+- DIP-K0402WS-V2.0
+
+**Key components**
+- U1: SPI NOR flash, 2 MiB
+- S1: unpopulated slide switch footprint (three through-holes used as serial console)
+
+Front panel
+
+<img src="photos/PCB-K0402WS-V2.0/chassis-front.jpg" width="400" />
+
+Bottom label
+
+<img src="photos/PCB-K0402WS-V2.0/chassis-bottom.jpg" width="400" />
+
+Top side (PCB)
+
+<img src="photos/PCB-K0402WS-V2.0/PCB-top.jpg" width="300" />
+
+### Port layout
+
+| Front panel position | Logical port | Physical port | Type    |
+|----------------------|--------------|---------------|---------|
+| SFP left             | 8            | 5             | SFP+    |
+| RJ45 1               | 4            | 1             | Copper  |
+| RJ45 2               | 5            | 2             | Copper  |
+| RJ45 3               | 6            | 3             | Copper  |
+| RJ45 4               | 7            | 4             | Copper  |
+| SFP right            | 3            | 6             | SFP+    |
+
+### Serial console
+
+The PCB has three unpopulated through-holes intended for a slide switch, directly connected to UART0.
+Numbered from the left (SFP port side), the pinout is:
+
+| Position (left→right) | Signal | GPIO                     |
+|-----------------------|--------|--------------------------|
+| 1 (leftmost)          | RX     | GPIO32\_UART0\_RX (32)   |
+| 2 (middle)            | GND    | GND                      |
+| 3 (rightmost)         | TX     | GPIO31\_UART0\_TX (31)   |
+
+- **Settings**: 115200 baud / 8N1 / 3.3V TTL
+- Connect a USB-TTL adapter: adapter TX → pin 1, GND → pin 2, adapter RX → pin 3
+
+### LED configuration
+
+Copper ports use LED SET0, SFP ports use LED SET1.
+
+| SET  | LED0                                             | LED2                                              |
+|------|--------------------------------------------------|---------------------------------------------------|
+| SET0 | Amber — lights on 2.5G link                      | Green — lights on 1G / 100M / 10M link            |
+| SET1 | All speeds — lights on any link with activity    | —                                                 |
+
+LED pad to physical port mapping:
+
+| GPIO pads | Port                    |
+|-----------|-------------------------|
+| GPIO8–11  | Physical port 5 (left SFP)  |
+| GPIO12–14 | Physical port 1 (RJ45 1)    |
+| GPIO15–17 | Physical port 2 (RJ45 2)    |
+| GPIO18–20 | Physical port 3 (RJ45 3)    |
+| GPIO21–23 | Physical port 4 (RJ45 4)    |
+| GPIO24–27 | Physical port 6 (right SFP) |
+
+### SFP GPIO assignments
+
+| SFP              | pin\_detect (ModAbs)        | pin\_los               | SerDes | I2C SDA              | I2C SCL                  |
+|------------------|-----------------------------|------------------------|--------|----------------------|--------------------------|
+| Left (logical 8) | GPIO30\_ACL\_BIT3\_EN       | GPIO37                 | SDS1   | GPIO39\_I2C\_SDA4    | GPIO40\_I2C\_SCL3\_MDC1  |
+| Right (logical 3)| GPIO50\_I2C\_SCL2\_UART1\_TX | GPIO51\_I2C\_SDA2\_UART1\_RX | SDS0 | GPIO41\_I2C\_SDA3\_MDIO1 | GPIO40\_I2C\_SCL3\_MDC1 |
+
+GPIO assignments were verified by observing GPIO state changes during SFP module insertion/removal
+and cross-checked against an original firmware register dump.
+`pin_tx_disable` is GPIO\_NA on both ports (original firmware keeps all GPIOs as inputs).

doc/supported_devices.md

@@ -7,6 +7,7 @@ The following devices have been tested and are fully working:
 | Davuaz   | Da-K6501W       | No      | [PCB-K0501W-V2.0](devices/K0501W_V2_0.md)                                 |       | 5 + 1 |
 | FOXNEO   | FNS-1200P       | No      | [PCB-K0402W-U13-V2.0](devices/FNS-1200P.md)                               | 2M    | 4 + 2 |
 | Hisource | Hi-K0402WS      | No      | [PCB-K0402WS-V3.0](devices/PCB-K0402WS-V3.0.md)                           |       | 4 + 2 |
+| Hisource | Hi-K0402WS      | No      | [PCB-K0402WS-V2.0](devices/PCB-K0402WS-V2.0.md)                           | 2M    | 4 + 2 |
 | Hisource | Hi-K0801WS      | No      | [PCB-KO801W-V2.0](devices/HI-K0801WS.md)                                  |       | 8 + 1 |
 | hongyavision | LG-SG5T1    | No      | [PCB-SWTG024AS-V2.0_16895](devices/SWTG024AS-V2.0.md)                     | 0.5M  | 5 + 1 |
 | Horaco   | HC-SWTGW215AS   | Yes     | [SWTG024AS-A-V2.0.1_19650 5C 1SFP](devices/SWTG024AS-A-V2.0.1_5C_1SFP.md) | ?     | 5 + 1 |

machine.c

@@ -801,9 +801,13 @@ __code const struct machine machine = {
     },
 };
 
-#elif defined MACHINE_FNS1200P
+#elif defined(MACHINE_PCB_K0402WS_V2) || defined(MACHINE_FNS1200P)
 __code const struct machine machine = {
+#if defined(MACHINE_PCB_K0402WS_V2)
+	.machine_name = "PCB-K0402WS-V2.0",
+#else
     .machine_name = "FNS-1200P",
+#endif
     .isRTL8373 = 0,
     .min_port = 3,
     .max_port = 8,

machine.h

@@ -30,6 +30,7 @@
 // #define MACHINE_SWTGW218AS
 // #define MACHINE_PCB_SWTG018AS_V2_1_0
 // #define MACHINE_PCB_K0402WS_V3
+// #define MACHINE_PCB_K0402WS_V2
 // #define MACHINE_K0501W_V2_0
 // #define MACHINE_LIANGUO_ZX_SWTGW215AS
 // #define MACHINE_ZX310S_4T2XH

machine_init.c

@@ -48,7 +48,7 @@ void machine_custom_init(void) __banked
 	reg_bit_set(RTL837X_REG_LED_GLB_IO_EN, 6);
 }
 
-#elif defined MACHINE_FNS1200P
+#elif defined(MACHINE_PCB_K0402WS_V2) || defined(MACHINE_FNS1200P)
 void machine_custom_init(void) __banked
 {
     reg_bit_set(RTL837X_REG_LED_GLB_IO_EN, 6);