diff --git a/doc/devices/SWTG024AS.md b/doc/devices/SWTG024AS.md
index 6da9c5ce..05e89ee3 100644
--- a/doc/devices/SWTG024AS.md
+++ b/doc/devices/SWTG024AS.md
@@ -1,4 +1,5 @@
-### SWTG024AS
+# SWTG024AS
+
 SWTG024AS has at least 4 variants that look the same.
 
 Variants are `managed` and a `unmanaged` version.
@@ -8,16 +9,224 @@ Also the RJ45 connectors can be all plastic/non-shielded or with metal shielding
 ## Brands
 |Brand|Type|Managed|PCB|PCB Label|Flash|Chip RTL|
 |---|---|---|---|---|---|---|
-| LIANGUO |SWTG024AS |No|  SWTG024AS-v2.0-17452 | CM-23-11-2336 023-17453| 512 KiB | 8272 |
-| Horaco |ZX-SWTG124AS | Yes |  SWTG024AS-v2.0 | ??? | ??? | 8272 |
-| Xikestore |SKS3200M-4GPY2XF | Yes |  SWTG024AS-v1.0 | CM-23-08-2043 023-16721 | 2048 KiB | 8272 |
+| Binardat | 2G06-04210GSM | No | PCB-SWTG024AS-A-2.0.1 | --- | 16MB | RTL8372N |
+| Horaco | ZX-SWTG124AS | Yes | SWTG024AS-v2.0 | ??? | ??? | 8272 |
+| LIANGUO | SWTG024AS | No | SWTG024AS-v2.0-17452 | CM-23-11-2336 023-17453 | 512 KiB | 8272 |
+| ONT | ONT-S207CW-62TS-SE | No | PCB-SWTG024AS-A-2.0.1 | --- | 16MB | RTL8372N |
 | Sodola | SL-SWTG124AS-D | Yes | SWTG024AS-v2.0-17452 | ??? | 2048 KiB | 8272 |
+| Xikestore | SKS3200M-4GPY2XF | Yes | SWTG024AS-v1.0 | CM-23-08-2043 023-16721 | 2048 KiB | 8272 |
 
 ## PCB
 
 <img src="photos/SWTG024AS-v2.0-unmanaged/SWTG024AS-v2.0-top-uman.png" width="300" />
 
-# SWTG024AS-v2.0 managed vs unmanged
+## PCB-SWTG024AS-A-2.0.1 Variant
+
+**Note:** ONT-S207CW-62TS-SE and Binardat 2G06-04210GSM are **identical in hardware** to this PCB variant. The only difference is the brand label.
+
+### Compatible Devices
+
+The following devices use the **same PCB-SWTG024AS-A-2.0.1 hardware** and are fully compatible with the same firmware configuration:
+
+| Brand | Model | Notes |
+|---|---|---|
+| ONT | ONT-S207CW-62TS-SE | Original device |
+| Binardat | 2G06-04210GSM | Identical hardware, same firmware |
+
+All these devices can use **MACHINE_PCB_SWTG024AS_A_2_0_1** with the LED configuration from this document.
+
+### Photos (Binardat 2G06-04210GSM)
+
+**Front View:**
+<img src="photos/SWTG024AS-v2.0-unmanaged/binardat-2g06-04210gsm-front.jpg" width="400" />
+
+**Back View:**
+<img src="photos/SWTG024AS-v2.0-unmanaged/binardat-2g06-04210gsm-back.jpg" width="400" />
+
+**PCB View:**
+<img src="photos/SWTG024AS-v2.0-unmanaged/binardat-2g06-04210gsm-pcb.jpg" width="400" />
+
+*Photos courtesy of [andreas5232](https://github.com/andreas5232) from [emesix/ONT-S207CW-62TS-SE#1](https://github.com/emesix/ONT-S207CW-62TS-SE/issues/1)*
+
+### Hardware Specification
+
+| Feature | Value |
+|---|---|
+| **CPU** | RTL8372N (detected via serial: "Detecting CPU: RTL8372N") |
+| **Flash** | GD25Q128E (16MB) |
+| **RAM** | Integrated in RTL8372N |
+| **RJ45 Ports** | 4x 2.5GBase-T (Ports 1-4) |
+| **SFP+ Ports** | 2x 10G (Ports 5-6) |
+| **Console** | 115200 baud (RTLPlayground firmware) / 9600 baud (stock firmware) |
+| **Web UI IP** | 192.168.2.1 |
+| **Loader Mode IP** | 192.168.10.247 |
+
+### Port Layout
+
+```
+┌─────────────────────────────────────────────┐
+│  ┌─────┐ ┌─────┐ ┌─────┐ ┌─────┐   ┌─────┐ ┌─────┐  │
+│  │RJ45 │ │RJ45 │ │RJ45 │ │RJ45 │   │SFP+ │ │SFP+ │  │
+│  │  1  │ │  2  │ │  3  │ │  4  │   │  5  │ │  6  │  │
+│  └─────┘ └─────┘ └─────┘ └─────┘   └─────┘ └─────┘  │
+│                                                     │
+│  [System LEDs]                                      │
+└─────────────────────────────────────────────┘
+```
+
+### Port Mapping
+
+Physical front panel (left to right):
+- Ports 1-4: RJ45 2.5GBase-T
+- Ports 5-6: SFP+ 10G (Port 5 = left/J4/SFP1, Port 6 = right/J2/SFP2)
+
+RTLPlayground logical mapping:
+- Logical port 3 → Physical SFP1 (J4, left)
+- Logical port 8 → Physical SFP2 (J2, right)
+- Logical ports 4-7 → Physical RJ45 ports 1-4
+
+| Physical Port | Logical Port | Type | LED Set | Web UI Port |
+|---|---|---|---|---|
+| 1 | 4 | RJ45 | 0 | 1 |
+| 2 | 5 | RJ45 | 0 | 2 |
+| 3 | 6 | RJ45 | 0 | 3 |
+| 4 | 7 | RJ45 | 0 | 4 |
+| 5 | 3 | SFP+ | 1 | 5 |
+| 6 | 8 | SFP+ | 1 | 6 |
+
+### LED Behavior (RTLPlayground v10+)
+
+#### RJ45 Ports (1-4)
+| LED Color | Speed |
+|---|---|
+| **Green** | 2.5G |
+| **Orange** | 1G / 100M / 10M |
+| **Off** | No link |
+
+#### SFP+ Ports (5-6)
+| LED Color | Speed |
+|---|---|
+| **Green** | 10G |
+| **Orange** | 2.5G / 1G |
+| **Off** | No link / No SFP module |
+
+### RTLPlayground Configuration
+
+**machine.h:**
+```c
+#define MACHINE_PCB_SWTG024AS_A_2_0_1
+```
+
+**machine.c configuration:**
+```c
+__code const struct machine machine = {
+    .machine_name = "PCB-SWTG024AS-A-2.0.1",
+    .isRTL8373 = 0,                    // RTL8372N
+    .mac_flash_offset = 0x1FC000,
+    .min_port = 3,
+    .max_port = 8,
+    .n_sfp = 2,
+    .log_to_phys_port = {0, 0, 0, 5, 1, 2, 3, 4, 6},
+    .phys_to_log_port = {4, 5, 6, 7, 3, 8, 0, 0, 0},
+    .is_sfp = {0, 0, 0, 1, 0, 0, 0, 0, 2},
+    
+    // SFP port on SDS0 / logical port 3
+    .sfp_port[0].pin_detect = GPIO37,
+    .sfp_port[0].pin_los = GPIO_NA,
+    .sfp_port[0].pin_tx_disable = GPIO_NA,
+    .sfp_port[0].sds = 0,
+    .sfp_port[0].i2c = { .sda = GPIO41_I2C_SDA3_MDIO1, .scl = GPIO40_I2C_SCL3_MDC1 },
+    
+    // SFP port on SDS1 / logical port 8
+    .sfp_port[1].pin_detect = GPIO38,
+    .sfp_port[1].pin_los = GPIO_NA,
+    .sfp_port[1].pin_tx_disable = GPIO_NA,
+    .sfp_port[1].sds = 1,
+    .sfp_port[1].i2c = { .sda = GPIO39_I2C_SDA4, .scl = GPIO40_I2C_SCL3_MDC1 },
+    
+    .reset_pin = GPIO_NA,
+    .high_leds = { .mux = LED_28_SYS | LED_29, .enable = LED_27 | LED_28_SYS | LED_29 },
+    .port_led_set = { 0, 0, 0, 1, 0, 0, 0, 0, 1 },
+    .led_sets = {
+        { // SET0: RJ45 - Green for 2.5G, Orange for 1G/100M/10M
+            LEDS_2G5 | LEDS_LINK | LEDS_ACT,
+            LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
+            0,
+            0
+        },
+        { // SET1: SFP+ - Green for 10G, Orange for 1G/2.5G
+            LEDS_10G | LEDS_LINK | LEDS_ACT,
+            LEDS_2G5 | LEDS_1G | LEDS_LINK | LEDS_ACT,
+            0,
+            0
+        },
+    },
+    .led_mux_custom = 1,
+    .led_mux = {
+        0x00,0x01,0x04,0x05,0x08,0x09,0x0c,0x3f,0x0d,0x10,0x11,0x0e,
+        0x14,0x11,0x12,0x15,0x15,0x16,0x18,0x19,0x1a,0x19,0x1d,0x1e,
+        0x1c,0x1d,0x20,0x21
+    },
+};
+```
+
+### Firmware History
+
+| Version | Date | Changes | Status |
+|---|---|---|---|
+| v3 | 2026-09-14 | Original PCB_SWTG024AS_A_2_0_1 config | All ports working, LEDs wrong |
+| v10 | 2026-09-17 | LED colors corrected for RJ45 and SFP+ | All ports + LEDs working |
+
+### Known Issues & Fixes
+
+#### Issue: LEDs showing wrong colors
+**Symptom:** RJ45 ports show green at all speeds, SFP LEDs don't light up
+**Fix:** Use v10 firmware with corrected LED sets and LED mux configuration
+
+#### Issue: No network connectivity after flash
+**Symptom:** Switch boots but no ping response
+**Fix:** Ensure `.isRTL8373 = 0` (RTL8372N) is set - this device uses RTL8372N, not RTL8373
+
+### Flashing Instructions
+
+#### Via Loader Mode (CH341A)
+```bash
+flashrom -p ch341a_spi -c "GD25Q128E" -w rtlplayground-PCB_SWTG024AS_A_2_0_1.bin
+```
+
+#### Via Web UI
+1. Access the web interface at `http://192.168.2.1`
+2. Navigate to **Firmware Update** (under System tab)
+3. Upload `rtlplayground_oem_upgrade-PCB_SWTG024AS_A_2_0_1.bin`
+4. Wait for flash completion and automatic reboot
+
+### Recovery
+
+If flashing fails and the switch does not boot:
+
+1. **Loader Mode Recovery:**
+   - Hold reset button while powering on
+   - Switch should be accessible at `192.168.10.247`
+   - Flash via `curl -T firmware.bin http://192.168.10.247/firmware`
+
+2. **Serial Recovery:**
+   - Connect via UART (115200 baud for RTLPlayground, 9600 for stock)
+   - Use CH341A: `flashrom -p ch341a_spi -c "GD25Q128E" -w firmware.bin`
+
+### Stock Firmware Information
+
+- **Default IP:** 192.168.10.247
+- **Default Login:** admin/admin (varies by OEM)
+- **Console Baud:** 9600
+- **CPU:** RTL8372N
+- **Hardware detection string:** "PCB-SWTG024AS-A-2.0.1"
+
+**Note:** This variant uses the same PCB as described above but may have different component population.
+
+---
+
+# SWTG024AS-v2.0 managed vs unmanaged
+
 Changes I found with my board vs [Managed version](https://github.com/up-n-atom/SWTG118AS/tree/main/photos/SWGT024AS-v2.0) of the PCB.
 
 ### Bottom
@@ -27,7 +236,7 @@ Changes I found with my board vs [Managed version](https://github.com/up-n-atom/
 * LED3: Not installed (System Led)
 ### Top
 * K1: Not installed (Reset Button)
-* R95: Installed (SFP2 (J2) signal RX-LOS), means that the managed-version can´t use the RX-LOS function.
+* R95: Installed (SFP2 (J2) signal RX-LOS), means that the managed-version can't use the RX-LOS function.
 * R270: Installed (SFP1 (J4) signal RX-LOS), same here as above.
 * R268: Installed (SFP2 (J2) signal TX-DISABLE, but R262 200R pull-down is to high to drive by the SOC, needs mod!)
 * U5: Flash is only 512 KiB instead of 2/4 MiB.
@@ -60,14 +269,14 @@ Changes I found with my board vs [Managed version](https://github.com/up-n-atom/
 
 |`J4` SFP1 PINs | Signal | Component | GPIO | Notes |
 |---|---|---|---|---|
-|2|	TX_FAULT	        | B-R262	       | --- | | 
-|3|	TX_DISABLE	      | B-R263, T-R268 | GPIO38 | R262 = Pull-down 200R|
-|4|	MODDEF2 – SDA     |	B-R261, T-R266 | GPIO39 | |
-|5|	MODDEF1 – SCL     |	B-R260, T-R267 | GPIO40	| Shared with both SFP |
-|6|	MODDEF0 – PRESENT |	B-R259, T-R296 | GPIO30 | |
-|7|	RATE SEL          |	B-R257	       | ---    | |
-|8|	LOS	              | B-R258, T-R270 | GPIO37 | | 
-|9|	TO?               | B-R256	       | ---    | |
+|2| TX_FAULT | B-R262 | --- | |
+|3| TX_DISABLE | B-R263, T-R268 | GPIO38 | R262 = Pull-down 200R|
+|4| MODDEF2 – SDA | B-R261, T-R266 | GPIO39 | |
+|5| MODDEF1 – SCL | B-R260, T-R267 | GPIO40 | Shared with both SFP |
+|6| MODDEF0 – PRESENT | B-R259, T-R296 | GPIO30 | |
+|7| RATE SEL | B-R257 | --- | |
+|8| LOS | B-R258, T-R270 | GPIO37 | |
+|9| TO? | B-R256 | --- | |
 
 ## J2
 
@@ -76,14 +285,14 @@ Changes I found with my board vs [Managed version](https://github.com/up-n-atom/
 
 |`J2` SFP2 PINs | Signal | Component | GPIO | Notes |
 |---|---|---|---|---|
-|2|	TX_FAULT	        | B-R70	         | ---	  | |
-|3|	TX_DISABLE	      | B-R10, B-R105-R, T-R88-L | GPIO54	| R10 = Pull-down 200R |
-|4|	MODDEF2 – SDA     |	B-R26, T-R85   | GPIO41 | |
-|5|	MODDEF1 – SCL     |	B-R15, T-R87   | GPIO40	| Shared with both SFP |
-|6|	MODDEF0 – PRESENT |	B-R14, T-R89   | GPIO50	| |
-|7|	RATE SEL          |	B-R12	         | ---	  | | 
-|8|	LOS	              | B-R13, T-R95   | GPIO51	| | 
-|9|	TO?               | B-R11	         | ---	  | | 
+|2| TX_FAULT | B-R70 | --- | |
+|3| TX_DISABLE | B-R10, B-R105-R, T-R88-L | GPIO54 | R10 = Pull-down 200R |
+|4| MODDEF2 – SDA | B-R26, T-R85 | GPIO41 | |
+|5| MODDEF1 – SCL | B-R15, T-R87 | GPIO40 | Shared with both SFP |
+|6| MODDEF0 – PRESENT | B-R14, T-R89 | GPIO50 | |
+|7| RATE SEL | B-R12 | --- | |
+|8| LOS | B-R13, T-R95 | GPIO51 | |
+|9| TO? | B-R11 | --- | |
 
 Note: component numbering `<L>-<REFDES>-<SIDE>`
 * L: Layer, T=Top, B=Bottom
@@ -108,7 +317,7 @@ The Slave Interface allows an extenal host to controll the SOC even if the inter
 Depending on the `IF_SEL` bootstrap resistors, this can me `I2C`, `SPI` or `SMI`.
 On this device it is `I2C` on address `0b1011100` or `0x5c` (7-bit notation).
 
-* I2c Read:  must be a write_read opperation `<Dev-ADDR><RegAddr15:8><RegAddr7:0>` `<DevAddr><Data7:0><Data15:8><Data23:16><Data31:24>`.
+* I2c Read: must be a write_read opperation `<Dev-ADDR><RegAddr15:8><RegAddr7:0>` `<DevAddr><Data7:0><Data15:8><Data23:16><Data31:24>`.
 * I2c Write: `<Dev-ADDR><RegAddr15:8><RegAddr7:0><DevAddr><Data7:0><Data15:8><Data23:16><Data31:24>`.
 
 Example register `0x0004` return chip id `0x00, 0x00, 0x72, 0x83` = `0x83720000`.
@@ -126,9 +335,9 @@ Note: 1 pin is square shaped.
 |`T8` pin|what|Signal|
 |---|---|---|
 | 1 | GPIO46 | |
-| 2 | GND    | |
+| 2 | GND | |
 | 3 | GPIO48 | |
-| 4 | 3V3    | |
+| 4 | 3V3 | |
 | 5 | GPIO47 | |
 | 6 | GPIO49 | |
 Note: 1 pin is square shaped.
@@ -136,47 +345,47 @@ Note: 1 pin is square shaped.
 # Reset ciruit
 | Cmp | Function |
 |---|---|
-| T-R78  | 33k PullUp      |
-| T-D3   | Discharge Diode |
-| T-C187 | RC-Delay        |
+| T-R78 | 33k PullUp |
+| T-D3 | Discharge Diode |
+| T-C187 | RC-Delay |
 
 Reset-line found at `T-D3-D` active-low.
 
 # GPIO
-| HEX VAL. | GPIO   | Component | What |  | GPIO | Component | What |
-| -------- | ------ |  ---- | ---- | ---- | ---- | ---- | ---- |
-| 00000001 | GPIO00 | T-C151-T, T-R28-T, T-R29-T |?    | | GPIO32 | T-R143-R | U0RXD |
-| 00000002 | GPIO01 | T-C152-T                |?    | | GPIO33 |  |  |
-| 00000004 | GPIO02 | T-C153-T                |?    | | GPIO34 |  |  |
-| 00000008 | GPIO03 | T-R33-T                 |?    | | GPIO35 |  |  |
-| 00000010 | GPIO04 | B-C155                  |?    | | GPIO36 | T-R88-L, T-R84-B | Optional SFP2 TX-DISABLE[^2], Reset |
-| 00000020 | GPIO05 | B-C156                  |?    | | GPIO37 | SFP1-8, T-R270 | SFP-LOS |
-| 00000040 | GPIO06 | T-C157-T                |?    | | GPIO38 | SFP1-3, T-R268 | SFP1 TX-DISABLE[^2] |
-| 00000080 | GPIO07 | T-C158-T, R165          |?    | | GPIO39 | SFP1-4, T-R266 | I2C-SDA4 |
-| 00000100 | GPIO08 |                         |     |  | GPIO40 | SFP2-5, T-R87; SFP1-5, T-R267; | I2C-SCL |
-| 00000200 | GPIO09 | SFP2-LED, T-R36-T       |LED-SFP2 | | GPIO41 | SFP2-4, T-R85 | I2C-SDA |
-| 00000400 | GPIO10 |                         |     | | GPIO42 |  U8-P6, T-R124 | SPI-MEMORY, CLK |
-| 00000800 | GPIO11 |                         |LEDx[^1] | | GPIO43 | U8-P5, T-R127 | SPI-MEMORY, DI,IO0 |
-| 00001000 | GPIO12 |                         |LEDx[^1] | | GPIO44 | U8-P2, T-R128 | SPI-MEMORY, DO,IO1 |
-| 00002000 | GPIO13 | PORT1-LED-GREEN         |LEDx[^1] | | GPIO45 | U8-P1, T-R123 | SPI-MEMORY, CS  |
-| 00004000 | GPIO14 | PORT1-LED-YELLOW        |LEDx | | GPIO46 | T8-1, T-R188| ? |
-| 00008000 | GPIO15 |                         |LEDx[^1] | | GPIO47 | T8-5, T-R190 | ? |
-| 00010000 | GPIO16 | PORT2-LED-GREEN         |LEDx[^1] | | GPIO48 | T8-3, T-R189 | ? |
-| 00020000 | GPIO17 | PORT2-LED-YELLOW        |LEDx | | GPIO49 | T8-6, T-R190 | ? |
-| 00040000 | GPIO18 |                         |LEDx[^1] | | GPIO50 | SFP2-6, T-R89 | SFP-DETECT |
-| 00080000 | GPIO19 | PORT3-LED-GREEN         |LEDx[^1] | | GPIO51 | SFP2-8, T-R95 | SFP-LOS |
-| 00100000 | GPIO20 | PORT3-LED-YELLOW        |LEDx | | GPIO52 |  |  |
-| 00200000 | GPIO21 |                         |LEDx[^1] | | GPIO53 |  |  |
-| 00400000 | GPIO22 | PORT4-LED-GREEN         |LEDx[^1] | | GPIO54 | SFP2-3, T-R105-L | SFP2 TX-DISABLE[^2] or via T-R85 to RESET[^3], T-R84-T |
-| 00800000 | GPIO23 | PORT4-LED-YELLOW        |LEDx | | GPIO55 | T-R78-B | |
-| 01000000 | GPIO24 | SFP1-LED-J4, T-R35      |LED-SFP1 | | GPIO56 | | |
-| 02000000 | GPIO25 |                         |     | | GPIO57 | | |
-| 04000000 | GPIO26 | ?                       |LEDx | | GPIO58 | | |
-| 08000000 | GPIO27 | R44L                    |?    | | GPIO59 | | |
-| 10000000 | GPIO28 | LED-SYSTEM, T-R50-R     |LED-SYSTEM  | | GPIO60 | | |
-| 20000000 | GPIO29 | T-R187-R                |     | | GPIO61 | | |
-| 40000000 | GPIO30 | SFP1-6, T-R269          |SFP-DETECT | | GPIO62 | | |
-| 80000000 | GPIO31 | T-R144-R                |U0TXD| | GPIO63 | | |
+| HEX VAL. | GPIO | Component | What | | GPIO | Component | What |
+| -------- | ------ | ---- | ---- | ---- | ---- | ---- | ---- |
+| 00000001 | GPIO00 | T-C151-T, T-R28-T, T-R29-T |? | | GPIO32 | T-R143-R | U0RXD |
+| 00000002 | GPIO01 | T-C152-T |? | | GPIO33 | | |
+| 00000004 | GPIO02 | T-C153-T |? | | GPIO34 | | |
+| 00000008 | GPIO03 | T-R33-T |? | | GPIO35 | | |
+| 00000010 | GPIO04 | B-C155 |? | | GPIO36 | T-R88-L, T-R84-B | Optional SFP2 TX-DISABLE[^2], Reset |
+| 00000020 | GPIO05 | B-C156 |? | | GPIO37 | SFP1-8, T-R270 | SFP-LOS |
+| 00000040 | GPIO06 | T-C157-T |? | | GPIO38 | SFP1-3, T-R268 | SFP1 TX-DISABLE[^2] |
+| 00000080 | GPIO07 | T-C158-T, R165 |? | | GPIO39 | SFP1-4, T-R266 | I2C-SDA4 |
+| 00000100 | GPIO08 | | | | GPIO40 | SFP2-5, T-R87; SFP1-5, T-R267; | I2C-SCL |
+| 00000200 | GPIO09 | SFP2-LED, T-R36-T |LED-SFP2 | | GPIO41 | SFP2-4, T-R85 | I2C-SDA |
+| 00000400 | GPIO10 | | | | GPIO42 | U8-P6, T-R124 | SPI-MEMORY, CLK |
+| 00000800 | GPIO11 | |LEDx[^1] | | GPIO43 | U8-P5, T-R127 | SPI-MEMORY, DI,IO0 |
+| 00001000 | GPIO12 | |LEDx[^1] | | GPIO44 | U8-P2, T-R128 | SPI-MEMORY, DO,IO1 |
+| 00002000 | GPIO13 | PORT1-LED-GREEN |LEDx[^1] | | GPIO45 | U8-P1, T-R123 | SPI-MEMORY, CS |
+| 00004000 | GPIO14 | PORT1-LED-YELLOW |LEDx | | GPIO46 | T8-1, T-R188| ? |
+| 00008000 | GPIO15 | |LEDx[^1] | | GPIO47 | T8-5, T-R190 | ? |
+| 00010000 | GPIO16 | PORT2-LED-GREEN |LEDx[^1] | | GPIO48 | T8-3, T-R189 | ? |
+| 00020000 | GPIO17 | PORT2-LED-YELLOW |LEDx | | GPIO49 | T8-6, T-R190 | ? |
+| 00040000 | GPIO18 | |LEDx[^1] | | GPIO50 | SFP2-6, T-R89 | SFP-DETECT |
+| 00080000 | GPIO19 | PORT3-LED-GREEN |LEDx[^1] | | GPIO51 | SFP2-8, T-R95 | SFP-LOS |
+| 00100000 | GPIO20 | PORT3-LED-YELLOW |LEDx | | GPIO52 | | |
+| 00200000 | GPIO21 | |LEDx[^1] | | GPIO53 | | |
+| 00400000 | GPIO22 | PORT4-LED-GREEN |LEDx[^1] | | GPIO54 | SFP2-3, T-R105-L | SFP2 TX-DISABLE[^2] or via T-R85 to RESET[^3], T-R84-T |
+| 00800000 | GPIO23 | PORT4-LED-YELLOW |LEDx | | GPIO55 | T-R78-B | |
+| 01000000 | GPIO24 | SFP1-LED-J4, T-R35 |LED-SFP1 | | GPIO56 | | |
+| 02000000 | GPIO25 | | | | GPIO57 | | |
+| 04000000 | GPIO26 | ? |LEDx | | GPIO58 | | |
+| 08000000 | GPIO27 | R44L |? | | GPIO59 | | |
+| 10000000 | GPIO28 | LED-SYSTEM, T-R50-R |LED-SYSTEM | | GPIO60 | | |
+| 20000000 | GPIO29 | T-R187-R | | | GPIO61 | | |
+| 40000000 | GPIO30 | SFP1-6, T-R269 |SFP-DETECT | | GPIO62 | | |
+| 80000000 | GPIO31 | T-R144-R |U0TXD| | GPIO63 | | |
 
 # LEDs
 
@@ -185,10 +394,10 @@ Reset-line found at `T-D3-D` active-low.
 | SYSTEM | T-R50-R (PU-4k2), T-R49-L, T-C185-L, B-R90 | GPIO28 | Low |
 | SFP1 | T-R35-L (PU-3k9), T-R34-L, T-C179-L | GPIO24 | Low |
 | SFP2 | T-R36-T (PD-4k0) | GPIO09 | High |
-| PORT1-LED-YELLOW |  | GPIO14 | Low |
-| PORT2-LED-YELLOW |  | GPIO17 | Low |
-| PORT3-LED-YELLOW |  | GPIO20 | Low |
-| PORT4-LED-YELLOW |  | GPIO23 | Low |
+| PORT1-LED-YELLOW | | GPIO14 | Low |
+| PORT2-LED-YELLOW | | GPIO17 | Low |
+| PORT3-LED-YELLOW | | GPIO20 | Low |
+| PORT4-LED-YELLOW | | GPIO23 | Low |
 
 # Power supply
 
diff --git a/doc/devices/photos/SWTG024AS-v2.0-unmanaged/binardat-2g06-04210gsm-back.jpg b/doc/devices/photos/SWTG024AS-v2.0-unmanaged/binardat-2g06-04210gsm-back.jpg
new file mode 100644
index 00000000..c9a16768
Binary files /dev/null and b/doc/devices/photos/SWTG024AS-v2.0-unmanaged/binardat-2g06-04210gsm-back.jpg differ
diff --git a/doc/devices/photos/SWTG024AS-v2.0-unmanaged/binardat-2g06-04210gsm-front.jpg b/doc/devices/photos/SWTG024AS-v2.0-unmanaged/binardat-2g06-04210gsm-front.jpg
new file mode 100644
index 00000000..4b20da5b
Binary files /dev/null and b/doc/devices/photos/SWTG024AS-v2.0-unmanaged/binardat-2g06-04210gsm-front.jpg differ
diff --git a/doc/devices/photos/SWTG024AS-v2.0-unmanaged/binardat-2g06-04210gsm-pcb.jpg b/doc/devices/photos/SWTG024AS-v2.0-unmanaged/binardat-2g06-04210gsm-pcb.jpg
new file mode 100644
index 00000000..6c2c32c8
Binary files /dev/null and b/doc/devices/photos/SWTG024AS-v2.0-unmanaged/binardat-2g06-04210gsm-pcb.jpg differ
diff --git a/machine.c b/machine.c
index 424c2c93..3784ef6d 100644
--- a/machine.c
+++ b/machine.c
@@ -864,8 +864,9 @@ __code const struct machine machine = {
 
 
 #elif defined MACHINE_PCB_SWTG024AS_A_2_0_1
-// NOTE: ONT-S207CW-62TS-SE uses this same configuration
-// See doc/devices/ONT-S207CW-62TS-SE.md for details
+// NOTE: ONT-S207CW-62TS-SE and Binardat 2G06-04210GSM use this same configuration
+// Both devices share identical PCB (PCB-SWTG024AS-A-2.0.1) with RTL8372N CPU
+// See doc/devices/SWTG024AS.md section "PCB-SWTG024AS-A-2.0.1 Variant" for details
 __code const struct machine machine = {
     .machine_name = "PCB-SWTG024AS-A-2.0.1",
     .isRTL8373 = 0,
diff --git a/machine.h b/machine.h
index 5cb13bc0..baeb7452 100644
--- a/machine.h
+++ b/machine.h
@@ -46,9 +46,10 @@
 // #define MACHINE_FG_8GT_1SX
 // #define MACHINE_LIANGUO_HYWS_SGT0108S
 // #define MACHINE_POE_2G080110GS
-// ONT-S207CW-62TS-SE: Identical to PCB-SWTG024AS-A-2.0.1 (RTL8372N, 4x2.5G + 2x10G SFP+)
-// Use MACHINE_PCB_SWTG024AS_A_2_0_1 for ONT-S207CW-62TS-SE
-// See doc/devices/ONT-S207CW-62TS-SE.md for configuration details
+// ONT-S207CW-62TS-SE and Binardat 2G06-04210GSM: Identical PCB-SWTG024AS-A-2.0.1
+// RTL8372N, 4x2.5G RJ45 + 2x10G SFP+, GD25Q128E (16MB)
+// Use MACHINE_PCB_SWTG024AS_A_2_0_1 for both devices
+// See doc/devices/SWTG024AS.md section "PCB-SWTG024AS-A-2.0.1 Variant" for details
 
 typedef struct {
 	// GPIO pins for SDA/SCL