Merge pull request #119 from feelfree69/swtgw218as

Add MACHINE_SWTGW218AS Managed Switch.
Deselect all MACHINE type so the use always have to select a machine type.

doc/devices/SWTGW218AS.md

@@ -0,0 +1,24 @@
+### ZX-SWTGW218AS
+
+## Brands
+|Brand|Type|Managed|PCB|Flash|Chip RTL|
+|---|---|---|---|---|---|
+| Mokerlink | ZX-SWTGW218AS | Yes|  SWTG118AS-V2.0-16029 | 2MB (FM25Q16A)| 8273N + 8224N |
+| Sodola | | | | | |
+| Horaco | | | | | |
+
+
+## Photos
+
+<img src="photos/SWTGW218AS-managed/front.png" width="800" />
+
+<img src="photos/SWTGW218AS-managed/label.jpg" width="800" />
+
+## PCB
+
+See up'n'atom's Repo:
+
+https://github.com/up-n-atom/SWTG118AS/blob/main/photos/SWTG118AS-v2.0/SWTG118AS-v2.0-pcb-top.JPG
+
+https://github.com/up-n-atom/SWTG118AS/blob/main/photos/SWTG118AS-v2.0/SWTG118AS-v2.0-pcb-bottom.JPG
+

machine.c

@@ -213,6 +213,40 @@ __code const struct machine machine = {
 
 void machine_custom_init(void) { }
 
+#elif defined MACHINE_SWTGW218AS
+
+__code const struct machine machine = {
+	.machine_name = "SWTGW218AS 8+1 Managed Switch",
+	.isRTL8373 = 1,
+	.min_port = 0,
+	.max_port = 8,
+	.n_sfp = 1,
+	.log_to_phys_port = {1, 2, 3, 4, 5, 6, 7, 8, 9},
+	.phys_to_log_port = {0, 1, 2, 3, 4, 5, 6, 7, 8},
+	.is_sfp = {0, 0, 0, 0, 0, 0, 0, 0, 1},
+	.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
+	.sfp_port[0].pin_los = GPIO37,
+	.sfp_port[0].pin_tx_disable = GPIO_NA,
+	.sfp_port[0].sds = 1,
+	.sfp_port[0].i2c = { .sda = GPIO39_I2C_SDA4, .scl = GPIO40_I2C_SCL3_MDC1 },
+	.reset_pin = GPIO54_ACL_BIT2_EN,
+	.high_leds = { .mux = LED_27 | LED_28 | LED_29, .enable = LED_28 | LED_29 },
+	.port_led_set = { 0, 0, 0, 0, 0, 0, 0, 0, 1},
+	.led_sets = { { LEDS_2G5 | LEDS_LINK | LEDS_ACT, // Green LED (right)
+					0, // unused
+					LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT, // Amber LED (left)
+					0
+				  }, // unused
+				  { LEDS_10G | LEDS_5G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_LINK | LEDS_ACT, // SFP LED
+					0, // unused
+					0, // unused
+					0
+				  }, // unused		    	},
+				},
+};
+
+void machine_custom_init(void) { }
+
 #elif defined DEFAULT_8C_1SFP
 __code const struct machine machine = {
 	.machine_name = "8+1 SFP Port Switch",
@@ -314,4 +348,6 @@ __code const struct machine machine = {
 void machine_custom_init(void) { 
 	reg_bit_set(RTL837X_REG_LED_GLB_IO_EN, 6);
 }
+#else
+	#error "Please select a machine type in machine.h"
 #endif

machine.h

@@ -6,18 +6,17 @@
 /*
  * Select your machine type below
  */
-#define MACHINE_KP_9000_6XHML_X2
+// #define MACHINE_KP_9000_6XHML_X2
 // #define MACHINE_KP_9000_6XH_X
 // #define MACHINE_KP_9000_9XH_X_EU
 // #define MACHINE_SWGT024_V2_0
 // #define MACHINE_HORACO_ZX_SG4T2
 // #define MACHINE_TRENDNET_TEG_S562
 // #define MACHINE_HG0402XG_V1_1
+// #define MACHINE_SWTGW218AS
 // #define MACHINE_HI_K0402WS
 // #define DEFAULT_8C_1SFP
 
-// #define DEFAULT_5C_1SFP
-
 typedef struct {
 	// GPIO pins for SDA/SCL
 	uint8_t sda; 

rtlplayground.c

@@ -1902,6 +1902,8 @@ void bootloader(void)
 
 	leds_dump();
 
+	set_sys_led_state(SYS_LED_SLOW);
+
 	if (machine_detected.isRTL8373)
 		rtl8373_init();
 	else
@@ -1982,7 +1984,6 @@ void bootloader(void)
 			dest += 0x1000;
 		}
 	}
-	set_sys_led_state(SYS_LED_SLOW);
 
 #ifdef DEBUG
 	// This register seems to work on the RTL8373 only if also the SDS