Add support for YuanLey YS25-0402 (PCB-K0402WS-V1.0)

UART is broken out to the unpopulated switch header at the front of the
board.

This isn't quite the same as the V2.0 definition as the system led is
always on, not routed through the CPU.

Additionally, document that the newer revision of the same "YS25-0402"
is supported via the existing PCB-K0402WS-V3.0 target.

doc/devices/PCB-K0402WS-V1.0.md

@@ -0,0 +1,72 @@
+# PCB-K0402WS-V1.0
+
+This is the first revision of the PCB-K0402WS series of boards; it's very similar to 2.0 in terms of layout/wiring.
+
+The board does have footprints for a VLAN modeswitch at the front and a second flash chip on the bottom of the PCB, but these have been seen to ship unpopulated.
+
+### Brands
+
+* YuanLey YS25-0402 <sup><sub>Note: there are [multiple revisions](PCB-K0402WS-V3.0.md) of the YS25-0402. This first revision lacks the "Vlan" switch cutout on the front of the enclosure.</sub></sup>
+
+### Programming
+
+Use a SOIC-8 clamp to the flash chip (U1 on silkscreen) at the top of the board, leaving it otherwise unpowered.
+
+The board has been seen to ship with a single [BoyaMicro BY25Q16BSSIG](https://www.lcsc.com/datasheet/C382744.pdf) 16Mbit (2MiB) chip, though exact BOM may vary.
+
+<a href="photos/PCB-K0402WS-V1.0/flash.jpg"><img src="photos/PCB-K0402WS-V1.0/flash.jpg" width="300" /></a>
+
+### What works
+
+- All four 2.5GBASE-T RJ45 ports at 10/100/1000/2500 Mbps
+- Both SFP ports supporting 1G, 2.5G and 10G modules
+- LEDs (Power LED is always on)
+
+### PCB overview
+
+#### Board markings
+- Top silkscreen: PCB-K0402W-V1.0 / DIP-K0402WS-V1.0
+
+#### Key components
+- U1: SPI NOR flash, 2 MiB
+- S1: unpopulated slide switch footprint (three through-holes used as serial console)
+
+Front panel
+
+<a href="photos/PCB-K0402WS-V1.0/ports.jpg"><img src="photos/PCB-K0402WS-V1.0/ports.jpg" width="300" /></a>
+
+PCB top
+
+<a href="photos/PCB-K0402WS-V1.0/pcb-top.jpg"><img src="photos/PCB-K0402WS-V1.0/pcb-top.jpg" width="300" /></a>
+
+PCB bottom
+
+<a href="photos/PCB-K0402WS-V1.0/pcb-bottom.jpg"><img src="photos/PCB-K0402WS-V1.0/pcb-bottom.jpg" width="300" /></a>
+
+Bottom and rear
+
+<a href="photos/PCB-K0402WS-V1.0/bottom.jpg"><img src="photos/PCB-K0402WS-V1.0/bottom.jpg" width="300" /></a>
+
+### Power supply
+
+Input power is delivered via a standard DC barrel jack (5.5x2.1mm) with an included 12V 1A adapter.
+
+There is an optional grounding screw next to the DC input.
+
+### Serial console
+
+The PCB has a slide switch footprint (unpopulated) at the front right that is connected to the UART. It is labeled as "S1" on the silkscreen.
+
+Facing the top front (port) side of the board, the pinout from left to right is:
+
+| Position | Signal | GPIO              |
+|----------|--------|-------------------|
+| 1        | RX     | GPIO32\_UART0\_RX |
+| 2        | GND    | N/A               |
+| 3        | TX     | GPIO31\_UART0\_TX |
+
+Standard 0.1" / 2.54mm pin headers will not fit, so wires or clips may be used instead.
+
+The image below shows some oversized clips clumsily attached.
+
+<a href="photos/PCB-K0402WS-V1.0/uart.jpg"><img src="photos/PCB-K0402WS-V1.0/uart.jpg" width="300" /></a>

doc/devices/PCB-K0402WS-V3.0.md

@@ -22,6 +22,11 @@ of the device just above the big label, might be covered by a QC sticker.
 * SICSOLINK SL-G0402F
 
 <img src="photos/PCB-K0402WS-V3.0/SICSOLINK SL-G0402F.jpg" width="300"/>
+
+* YuanLey YS25-0402 <sup><sub>Note: there are [multiple revisions](PCB-K0402WS-V1.0.md) of the YS25-0402. This is the newer revision that has a "Vlan" switch on the front.</sub></sup>
+
+<img src="photos/PCB-K0402WS-V3.0/YuanLey_YS25-0402.jpg" width="300"/>
+
 ### Programming
 
 Using SPI clamp in-board is the only method for initial installation.

doc/supported_devices.md

@@ -42,6 +42,8 @@ The following devices have been tested and are fully working:
 | TRENDnet | TEG-S562        | No      | [TEG-S563/EU H/W: V1.0R](devices/TEG-S562.md)                             | 2M    | 4 + 2 |
 | XikeStor | SKS3200M-4GPY2XF| Yes     | [SWTG024AS-v1.0](devices/SWTG024AS.md)                                    |       | 4 + 2 |
 | XikeStor | SKS3200-8E1X    | Yes     | [SWTG118AS-V2.1-17462](devices/SWTGW218AS.md)                             | 2M    | 8 + 1 |
+| YuanLey  | YS25-0402       | No      | [PCB-K0402WS-V1.0](devices/PCB-K0402WS-V1.0.md)                           | 2M    | 4 + 2 |
+| YuanLey  | YS25-0402       | No      | [PCB-K0402WS-V3.0](devices/PCB-K0402WS-V3.0.md)                           | 2M    | 4 + 2 |
 | Ztyuav   | Z-QWYT0402      | No      | [PCB-K0402WS-V3.0](devices/PCB-K0402WS-V3.0.md)                           |       | 4 + 2 |
 
 For KP-9000-6XH-X2 / KP-9000-6XHML-X2 / Mokerlink 2G040210GSM devices, select

machine/PCB_K0402WS_V1.c

@@ -0,0 +1,57 @@
+#include "machine_defs.h"
+
+__code const struct machine machine = {
+	.machine_name = MACHINE_MODEL,
+	.isRTL8373 = 0,
+	.min_port = 3,
+	.max_port = 8,
+	.n_sfp = 2,
+	.log_to_phys_port = {0, 0, 0, 6, 1, 2, 3, 4, 5},
+	.phys_to_log_port = {4, 5, 6, 7, 8, 3, 0, 0, 0},
+	.is_sfp = {0, 0, 0, 2, 0, 0, 0, 0, 1},
+
+	/* Left SFP (logical 8, SDS1): GPIO30=ModAbs, GPIO37=RX_LOS */
+	.sfp_port[0].pin_detect = GPIO30_ACL_BIT3_EN,
+	.sfp_port[0].pin_los = GPIO37,
+	.sfp_port[0].pin_tx_disable = GPIO_NA,
+	.sfp_port[0].sds = 1,
+	.sfp_port[0].i2c = I2CBUS( GPIO39_I2C_SDA4, GPIO40_I2C_SCL3_MDC1 ),
+
+	/* Right SFP (logical 3, SDS0): GPIO50=ModAbs, GPIO51=RX_LOS */
+	.sfp_port[1].pin_detect = GPIO50_I2C_SCL2_UART1_TX,
+	.sfp_port[1].pin_los = GPIO51_I2C_SDA2_UART1_RX,
+	.sfp_port[1].pin_tx_disable = GPIO_NA,
+	.sfp_port[1].sds = 0,
+	.sfp_port[1].i2c = I2CBUS( GPIO41_I2C_SDA3_MDIO1, GPIO40_I2C_SCL3_MDC1 ),
+
+	.reset_pin = GPIO_NA,
+
+	/* These don't appear to be populated / wired-up; the power LED is always on */
+	.high_leds = { 0 },
+
+	/* Copper ports use SET0; SFP ports use SET1 */
+	.port_led_set = {0, 0, 0, 1, 0, 0, 0, 0, 1},
+
+	.led_sets = {
+		{	/* SET0: copper — LED0=amber (2.5G), LED2=green (1G/100M/10M) */
+			LEDS_2G5 | LEDS_LINK | LEDS_ACT,
+			0,
+			LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
+			0
+		},
+		{	/* SET1: SFP — all speeds link/act */
+			LEDS_10G | LEDS_2G5 | LEDS_1G | LEDS_100M | LEDS_10M | LEDS_LINK | LEDS_ACT,
+			0,
+			0,
+			0
+		},
+	},
+
+	.led_mux_custom = 1,
+	.led_mux = {
+		0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f,  /* GPIO0-7: unused */
+		0x0f, 0x0c, 0x0d, 0x0e, 0x10, 0x11, 0x12,        /* GPIO8-14 */
+		0x14, 0x15, 0x16, 0x18, 0x19, 0x1a,              /* GPIO15-20 */
+		0x1c, 0x1d, 0x1e, 0x20, 0x21, 0x22, 0x23         /* GPIO21-27 */
+	},
+};

machine/PCB_K0402WS_V1.h

@@ -0,0 +1,6 @@
+#ifndef _MACHINE_PCB_K0402WS_V1_H_
+#define _MACHINE_PCB_K0402WS_V1_H_
+
+#define MACHINE_MODEL "PCB-K0402WS-V1.0"
+
+#endif