Merge branch 'main' into add-device-ONT-S207CW-62TS-SE

doc/devices/F7008-2.5.md

@@ -0,0 +1,70 @@
+# F7008-2.5
+
+Documentation for the unmanaged 8 + 1 switch sold as `7018-2.5G` by Guangnianwei
+(光年微), board marking `F7008-2.5`, PCB `F7008-2.5GPOE-V1.2`.
+
+### Brands
+
+| Brand | Type | Managed | PCB | Flash | Chip RTL |
+|-------|------|---------|-----|-------|----------|
+| Guangnianwei (光年微) | 7018-2.5G | No | F7008-2.5GPOE-V1.2 | W25Q64JVSSIQ | 8373N + 8224N |
+
+### What works
+
+- All eight 2.5GBASE-T RJ45 ports at 10/100/1000/2500 Mbps
+- SFP+ port with 1G/2.5G/10G modules
+- LEDs of the eight RJ45 ports
+
+### Not verified
+
+- The LED pads for the SFP+ cage are not mapped yet. The SFP+ lamps are left
+  undriven, so an inserted module lights nothing.
+- The UART header footprint is present but unpopulated, and no boot log could be
+  captured from it, so the baud rate is unknown. There are most likely
+  unpopulated 0-Ohm resistors next to the header; bridging those should bring
+  the console to life.
+
+### Build target
+
+```
+make MACHINE=F7008_2_5
+```
+
+### LED wiring
+
+Measured pad to lamp map (`led_mux` index -> lamp):
+
+| Port | green lamp | yellow lamp |
+|------|-----------|-------------|
+| 1 | pad 0  | pad 1  |
+| 2 | pad 2  | pad 3  |
+| 3 | pad 4  | pad 5  |
+| 4 | pad 6  | pad 8  |
+| 5 | pad 9  | pad 10 |
+| 6 | pad 12 | pad 15 |
+| 7 | pad 18 | pad 21 |
+| 8 | pad 24 | pad 25 |
+
+Pads 7, 11, 13, 14, 16, 17, 19, 20, 22, 23, 26 and 27 do not drive an RJ45 lamp.
+
+The front panel is silkscreened `2.5G: Green / 10/100M: Yellow`, and the target
+follows it: the green lamp is on while the port is linked at 2.5G, the yellow
+lamp blinks while data is flowing.
+
+### PCB overview
+
+The board is marked `F7008-2.5GPOE-V1.2`.
+
+Top side:
+
+<img src="photos/F7008-2.5/PCB-top.jpg" width="600" />
+
+Bottom side:
+
+<img src="photos/F7008-2.5/PCB-bottom.jpg" width="600" />
+
+### Hardware notes
+
+- 4 x `RT4802SNE` magnetics
+- Unpopulated UART header footprint, next to the magnetics
+- Power input 12V 1A, 180 x 84 x 29 mm metal case

doc/devices/HASIVO_S1100WP_8GT_1SX_SE.md

@@ -0,0 +1,75 @@
+# Hasivo S1100WP-8GT-1SX-SE
+
+RTL8373-based 8×2.5G PoE + 1×SFP switch.
+
+### Label specifications
+
+- **Manufacturer**: Hasivo
+- **Model**: S1100WP-8GT-1SX-SE
+- **Ports**:
+  - 8 × RJ45: 10/100/1000/2500 Mbps with PoE
+  - 1 × SFP: 1G / 2.5G / 10G
+- **Power input**: DC 52V 2.5A
+- **Stock firmware defaults**: IP 192.168.0.1, user/password `admin`/`admin`
+
+### What works
+
+- All eight 2.5GBASE-T RJ45 ports at 10/100/1000/2500 Mbps (PoE is not configurable via RTLPlayground)
+- SFP port supporting 1G, 2.5G and 10G modules
+- LEDs: green (2.5G) and amber (1G/100M/10M) per copper port; combined link/act on the SFP port
+
+### Photos
+
+Front panel:
+
+<img src="photos/HASIVO_S1100WP-8GT-1SX-SE/front.jpg" width="600" />
+
+Label:
+
+<img src="photos/HASIVO_S1100WP-8GT-1SX-SE/label.jpg" width="600" />
+
+### PCB overview
+
+Top side:
+
+<img src="photos/HASIVO_S1100WP-8GT-1SX-SE/pcb_top.jpg" width="600" />
+
+Bottom side:
+
+<img src="photos/HASIVO_S1100WP-8GT-1SX-SE/pcb_bottom.jpg" width="600" />
+
+### Port layout
+
+| Logical port | Physical port | Type   |
+|--------------|---------------|--------|
+| 1-8          | 1-8           | Copper |
+| 9            | 9             | SFP    |
+
+### LED configuration
+
+Copper ports use LED SET0, the SFP port uses LED SET1.
+
+| SET  | LED0                                          | LED2                                                 |
+|------|-----------------------------------------------|------------------------------------------------------|
+| SET0 | Green — lights on 2.5G link with activity     | Amber — lights on 1G / 100M / 10M link with activity |
+| SET1 | All speeds — lights on any link with activity | —                                                    |
+
+### SFP GPIO assignments
+
+| SFP (logical 9) | pin_detect (ModAbs) | pin_los | pin_tx_disable | SerDes | I2C SDA         | I2C SCL             |
+|-----------------|---------------------|---------|----------------|--------|-----------------|---------------------|
+| SFP             | GPIO30_ACL_BIT3_EN  | GPIO37  | GPIO_NA        | SDS1   | GPIO39_I2C_SDA4 | GPIO40_I2C_SCL3_MDC1 |
+
+### Machine configuration
+
+- `reset_pin`: GPIO54_ACL_BIT2_EN
+- High LEDs (pads 27-29): mux = `LED_27 | LED_28_SYS | LED_29`, enable = `LED_28_SYS | LED_29`
+
+### PoE
+
+The 8 copper ports support PoE powered by a DC 52V 2.5A input. Power management is handled by two HS104PTI chipsets over I2C (GPIO47_I2C_SDA0, GPIO46_I2C_SCL0):
+
+* Chip 1 (I2C address 0x1A): 2.5G Ports 1–4
+* Chip 2 (I2C address 0x2A): 2.5G Ports 5–8
+
+Note: The current implementation does not yet support PoE management. Consequently, PoE currently operates in standalone mode without software control.

doc/devices/SWTG018AS_A_V2_0.md

@@ -1,9 +1,10 @@
 # SWTG018AS-A V2.0
 ## Brands
-| Brand  | Type             |Managed| PCB              | Flash           | Chip RTL      |
-|--------|------------------|-------|------------------|-----------------|---------------|
-| Ampcom | SWTG018AS-A V2.0 | No    | SWTG018AS-A V2.0 | 2MB             | 8273N + 8224N |
-| Horaco | HC-SWTGW218AS-A  | Yes   | SWTG018AS-A V2.0 | 2MB(25Q16JVSIQ) | 8273N + 8224N |
+| Brand   | Type             |Managed| PCB              | Flash           | Chip RTL      |
+|---------|------------------|-------|------------------|-----------------|---------------|
+| Ampcom  | SWTG018AS-A V2.0 | No    | SWTG018AS-A V2.0 | 2MB             | 8273N + 8224N |
+| Horaco  | HC-SWTGW218AS-A  | Yes   | SWTG018AS-A V2.0 | 2MB(25Q16JVSIQ) | 8273N + 8224N |
+| GoodTop | GT-ST018M        | Yes   | SWTG018AS-A V2.0 | ?               | 8273N + 8224N |
 
 
 The following is a documentation for the unmanaged switch marked as `SWTG018AS-A V2.0`.