Docs: Add SWTG024AS-v2.0-unmanaged version

Pinout Spreedsheet, photos and wiki about my findings. GPIO number may be has endian problem.
2026-08-30 14:52:51 +08:00 · 2025-09-06 10:23:09 +02:00
parent 8b91646b83
commit 0d63b08f89
4 changed files with 94 additions and 0 deletions
@@ -0,0 +1,94 @@
+### SWTG024AS
+SWTG024AS has at least 4 variants that look the same.
+
+Variants are `managed` and a` unmanaged` version.
+But both have pcb version `v1.0` and `v2.0`. 
+Also the RJ45 connects can be all plastic or metal shielding.
+
+# Unmanaged Switch
+## Brands
+|Brand|Type|Managed|PCB|PCB Label|Flash|Chip RTL|
+|---|---|---|---|---|---|---|
+| LIANGUO |SWTG024AS |No|  SWTG024AS-v2.0 | CM-23-11-2336 023-17453| 512kB| 8272 |
+
+# SWTG024AS-v2.0 managed vs unmanged
+Changed I found with my own board vs [Managed version](https://github.com/up-n-atom/SWTG118AS/tree/main/photos/SWGT024AS-v2.0) of the PCB.
+
+### Bottom
+*  R105: Installed, goes to R10-PullDown SFP2 -> TX DISABLE
+*  R85: Not Installed (Connected to K1)
+*  R90: Not installed (PowerLed) 
+*  LED3: Not installed (PowerLed)
+### Top
+* K1: Not installed (Reset butten)
+* R95: Installed (SFP2 signal RX-LOS), mean that the manage version can use RX-LOS function.
+* R270: Installed (SFP1 signal RX-LOS)
+* R268: Installed (SFP2 signal TX_DISABLE, but R262 200R pull-down is to high to drive by the SOC, needs mod!)
+
+### Notes
+* `TX Disable`-SFP2 and Button `K1` share the same GPIO pin via `R105` and `R85`.
+  But with `R88`, `TX Disable`-SFP2 can be mapped to `C4`.
+* `TX Disable` pull-down resistos on both SFP are to low to drive by the SOC.
+  We need to make a `Best`-BOM variant so we can use all the featues.
+
+# Connectors
+|`J4` SFP1 PINs | Signal | Component | GPIO | Notes |
+|---|---|---|---|---|
+|2|	TX_FAULT	      | B-R262	       | --- | | 
+|3|	TX_DISABLE	      | B-R263, T-R268 | C6	 | R262 = Pull-down 200R|
+|4|	MODDEF2 – SDA     |	B-R261	       | C7	 | |
+|5|	MODDEF1 – SCL     |	B-R260, T-R267 |---	 | |
+|6|	MODDEF0 – PRESENT |	B-R259, T-R296 | B30 | |
+|7|	RATE SEL          |	B-R257	       | --- | |
+|8|	LOS	              | B-R258, T-R270 | C5	 | | 
+|9|	TO?               | B-R256	       | --- | |
+
+|`J2` SFP2 PINs | Signal | Component | GPIO | Notes |
+|---|---|---|---|---|
+|2|	TX_FAULT	      | B-R70	      | ---	| |
+|3|	TX_DISABLE	      | B-R10, T-R88-L | C22	| R10 = Pull-down 200R |
+|4|	MODDEF2 – SDA     |	B-R26         | C9	| |
+|5|	MODDEF1 – SCL     |	B-R15, T-R87  |	---	| |
+|6|	MODDEF0 – PRESENT |	B-R14, T-R89  | C18	| |
+|7|	RATE SEL          |	B-R12	      | ---	| | 
+|8|	LOS	              | B-R13, T-R95  |	C19	| | 
+|9|	TO?               | B-R11	      | ---	| | 
+
+Note: component numbering `<L>-<REFDES>-<SIDE>`
+* L: Layer, T=Top, B=Bottom
+* REFDEES: full silkscreen like `R123`
+* SIDE: Side of the component. when the rj45 are facing towards you are you can read the silkscreen normal.
+  L = Left, R=right, B=bottom, T=top or P with a pin number.
+
+### T3
+This connector seems to go to U4 and U10.
+I thing is used to connect a external CPU to controlle the SOC.
+Even to program the flash via the SOC.
+Signals are based on that `U4` is likely a I2C-EEPROM, `U10` is likely other SPI-chip.
+|`T3` pin|what|Signal|
+|---|---|---|
+| 1 | U4-P6, 33R U10-P6| I2C-SCL, SPI-CLK |
+|2| GND | --- |
+|3| U4-P5, U10-P5  | I2C-SDA, SPI-DI/DO |
+|4| VCC  | 
+|5| 33R -> U10-P2 | SPI-DO/D1 | 
+|6| U10-P1 | SPI-CS |
+
+
+|`T8` pin|what|Signal|
+|---|---|---|
+| 1 | C14 | |
+| 2 | GND | |
+| 3 | C16 | |
+| 4 | 3V3 | |
+| 5 | C15 | |
+| 6 | C17 | |
+
+# Reset ciruit
+| Cmp | Function |
+|---|---|
+| R78 | 33k PullUp|
+| D3 | Discharge Diode |
+| C187 | RC-Delay |
+
+Reset-line found at `T-D3-D` active-low.